Search Documents

By G Huggins

Excavation in underground jointed rock masses creates cavities into which the surrounding rock mass deforms. Deformations, besides intact rock deformation, include mechanistic deformations such as slip and rotation. In this paper deformational moduli were measured for prototype and blocky (jointed) models using elastic analogue methods for stopes from MIM LimitedÆs Lead Mine. The blocks for the models were defined in terms of the prototypeÆs joint sets, their spatial separations, orientations and average friction characteristics. From dimensional analyses, a relationship between prototype and model deformations was used to predict stope mid-span deformations. The results of this physical modelling work, conducted in the 1970s, motivated an investigation into the electro-treatment of tailings backfill to achieve improved strength and stiffness characteristics. Tailings backfill containing fines and having a high clay content can be electrically dewatered, and at times grouted, cemented, ion exchanged or agglutinated, to achieve relatively high magnitudes of strength and stiffness. These treated tailings stiffnesses can reduce the deformation magnitudes within a rock mass and, in doing so, reduce problems encountered in mine pillar extraction. The application of these tailings modification techniques is examined in relation to the elastic analogue methods.

Jan 1, 1998

By Lane G

This paper addresses project commissioning, that is, activities that culminate in the transfer of a project from the construction phase to routine plant operation. These activities should be initiated early in the engineering and design phase to ensure that the plant design is operator friendly and that construction is scheduled such that pre-operational testing and hand over to the owner occurs in a timely and cost-effective manner. For the purposes of this paper, commissioning includes all activities related to pre-operational testing, no-load testing, water commissioning, and ore commissioning. That is, all activities from construction completion to practical completion of the prime contract. This process is facilitated in numerous ways dependent on the nature of the project prime contract and the size of the project. For small lump sum projects, the contractor's responsibility may include all phases of commissioning to practical completion, whereas, a managing contractor on a complex multi-contract project may only be required to bring the project to mechanical completion and hand over to the owner for ore commissioning. Irrespective of the responsibilities, commissioning programs require careful planning, effective communication and detailed reporting. Unsuccessful

Jan 1, 1997

By J E. Eberhardt

Ore sorting has long been used to raise the efficiency and thus lower the environmental impact of mineral processing operations. It was first instituted as hand sorting, according to a humanly perceived difference in the ore, but is now automated using large mechanical sorters in order to meet the high tonnage throughput required in most minerals processing applications. In the past, ore sorting was generally used as a niche processing route when other approaches failed, and in this context, consequential environmental benefits are often not the first consideration in adopting sorting. When applicable, ore sorting offers environmental benefits in reductions in fines waste, reagent usage and energy consumption in milling. Although there are significant opportunities for the use of ore sorting technology in many minerals processing operations, industry applications, to date, have been limited mainly to the processing of diamonds, magnesite, talc and uranium ores. This limitation has principally been due to a lack of suitable sensing technologies for a wide range of ore types. The authors report on a wide-ranging review of the automated sorting of mineral ores, and in particular, on methods for discrimination of ore characteristics prior to mechanical sorting.

Jan 1, 2002

Agglomeration Drum Selection and Design A model has been developed by for drum agglomeration which allows selection of geometry and power input. Specific aspects considered are: calculation of total operating volume, solids residence time based on drum geometry and operating parameters, selection of the drum aspect ratio, selection of proportion of critical speed, calculation of rotating power requirements. The model uses solids total residence time to calculate the required operating volume. The burden density is calculated from the solids bulk density, agglomerate packing and the fluid density. Power is calculated using a modified Liddell and Moys correlation for burden position and shape, and the operating drum speed. A further power allowance is made to allow for accretion drop off during drum rotation. Results from the model (especially power and per cent operating fill) have been verified from industrial installations of significant size. Predicted and observed power draws are within five per cent when burden slip and bypassing are not significant. When these are significant (at fills above 15 per cent) the actual power draw will be less than the model prediction. Under these circumstances the quality of the agglomerates will be poor.

Sep 13, 2010

By M Hino, D R. Swinbourne

The thermodynamic properties of arsenic in metal, speiss, matte, slag and gas phases are first summarised in this paper. Arsenic associates with sulphide minerals and generally has compounds of high volatility, but it has a weak affinity for sulphur and a strong affinity for metals, especially copper and iron. In the initial stage of the oxidation of sulphide concentrates arsenic is volatilised easily prior to the oxidation of FeS, although it tends to be fixed in the condensed phase as FeAsO4 if the concentrate is over-oxidised. Thermodynamic simulation of oxidative copper smelting reveals the distribution of arsenic between matte, slag and gas, and the possibility of condensation of arsenic from the resulting waste gas is discussed. In reductive smelting more arsenic remains in the metal or matte, and is sometimes concentrated as a separate speiss phase. The phase relations and thermodynamic properties of speiss are also summarised briefly. Arsenic refining from smelted copper metal is shown, from an examination of the basic principles of arsenic removal into slags, to be difficult. Owing to its weak affinity for lead however, arsenic refining from lead bullion is seen to be much easier.

Jan 1, 2000

By P Rourke

In this climate of increasing demand for commodities, it is becoming necessary to expand and optimise existing bulk material handling facilities in order to increase capacity to satisfy demand. Production capacity in these facilities is often adversely impacted during the expansion process. A successful and proven strategy to reduce this impact is to bring the additional capacity online in stages coinciding with routine maintenance or other short shutdowns. Compatibility of the automation systems with staged upgrades in capacity is the key to achieving a successful outcome. Since 1994, Hatch has been researching a generic, highly configurable product transport control system that can be reconfigured to cater for plant expansions or modifications without incurring significant risk to production capacity. In 2002, BHP Billiton Iron Ore (BHPB IO) recognised the need for such a generic Route Selection and Sequencing (RSS) system and engaged Hatch to build a generic RSS system as part of the $US351 million BHPB IO Products and Capacity Expansion (PACE) project. In 2004, Hatch successfully deployed such a generic configurable control system at BHPB IO Port Hedland Ore Handling Facility. This generic system is known as the Hatch Product Transport (HPT) System.

Jan 1, 2005

By Cripps-Clark CJ

Sulphur partition between metal and slag has been examined on a cast-by-cast basis for BTIP furnaces. Partition values. were calculated from thermodynamic equilibrium data together with oxygen activities computed from the manganese partition. The S-C interaction coefficient, esc , was treated as an adjust- able parameter and the agreement between calculated and measured S partition values optimized. In the case of furnaces operating with low viscosity slags this procedure led to estimates of esc in close agreement with previously measured values. The same analysis applied to daily average data for several Kawasaki Steel furnaces led to the same esti- mates of e c s , indicating a similar approach to equilibrium. Silicon partition between metal and slag has been examined on a time average basis and found to be far removed from thermodynamic equilibrium for most Australian furnaces. A study of Japanese furnaces of comparable size reveals a temperature dependence of Si parti- tion which appears to be close to equilibrium. Australian furnaces approach this behaviour only when operating with low viscosity slags. A preliminary examination of the effects of burdening with TiO 2 on the silicon partition is also reported.

Jan 1, 1980

By Koeng R, Richardson M, Hoare R

A discrete event computer simulation model was developed for two of the stoping methods currently used at the Z.C. Mines Broken Hill oper- ations. The objective in undertaking this project was to provide an effective tool for mine planning and design to allow comparisons of alternative extraction strategies and attempt to optimise the allocation of capital equipment and human resources. The Slam II simulation program was used in conjunction with ,a com- monly used data editor, text editor and graphics package to allow the simulation to be done on a personal computer with minimum training requirements. The computer hardware used was a portable computer cur- rently available using 80386/20MHz electronics. Specific logic techniques were developed to allow the Slam II language to simulate mining opera- tions because it was originally developed for manufacturing and com- mercial simulations. The design of the model was based on observations and a data collec- tion campaign. The model was designed with flexibility which allows simple editing of the input data which includes: - Insitu volumes - Development statistics -Loadout efficiencies -Loader speeds, availabilities and capacities -Chute numbers, volumes, distances and blockage statistics -Trucking statistics -Work schedules -Utility statistics

Jan 1, 1988

By Kitzinger F

The economic climate of the Canadian mining industry forced an increased interest in rapid, continuous excavation techniques for hard rock formations. The potential applications and advantages of continuous mining over the present drill- blast-muck labour intensive cyclical methods are considerable. Noranda investigated an electrical technique, Plasma Blasting showing considerable promise for mining hard rock. The background of the technology and the theory of blasting rock with electricity is described. The Plasma Blasting process is based on the fast discharge of stored electrical energy into a small amount of electrolyte, suitably located in the rock. The electrical energy converts the electrolyte into high pressure plasma, which expands very quickly, thereby, generating a shock wave. This shock wave produces a stress field inside the rock, resulting in a blast similar to that made by chemical explosives, but without the deleterious fumes. Noranda is currently blasting boulders of 4-5 tonnes and is at present constructing a mobile, autonomous secondary rock breaker for underground and open pit applications. Tests on in situ hard rock formations will lead to the development of a continuous mining machine. Production rates of 500 tonnes per man-shift could be obtained with such a machine.

Jan 1, 1990

By Cripps-Clark CJ, Deague TK

In order to study conditions under which SiO(g) may be formed in a blast furnace, equilibrium phase diagrams were constructed for the combustion of high and low ash cokes with oxygen-enriched blast and oil injection under conditions of high and low raceway pressures. Free energy minimisation techniques were used to calculate the composition of gaseous and condensed phases. Where coke ash is assumed, for simplicity, to comprise Si02 only, the coke can be comple- tely gasified, mainly to SiO and CO, under restricted conditions of coke to blast ratio and at temperatures greater than 1600 - 1650¦C, depending on system pressure. The formation of SiO(g) is partially suppressed by the introduction of alumina into the ash, because of the formation of solid and liquid alumino- silicate compounds. The minimum temperature for complete silicon gasification is raised to about 1700¦C. The results of the equilibrium calcula- tions are related-to actual raceway conditions. It is proposed that virtually all silicon in the coke ash is gasified such that, on condensation, it affects hot metal chemistry and slag properties and secondly, that the effects will be greater with higher ash cokes.

Jan 1, 1980

By Marshall GA

Structural fatigue damage of haul truck frames is a costly problem associated with the operation of large mine haul trucks. A monitoring programme is described which has been instigated to measure stresses in the frames of haul trucks under actual mine operating conditions. The instrumentation used and methodology employed in the computer analysis of the results is briefly described. The results of the monitoring programmes are reviewed, and the effects of various factors affecting structural fatigue damage of three common types of rear dump truck are considered. Factors discussed include the effects of haul route features (for example shovel, dump and crusher areas); the effect of operations such as turning, braking, loading and dumping; the influence of payload; the effects of malfunctions in suspensions; and the influence of haul route surface quality. It is shown that with respect to payload, while structural fatigue damage is increased with payload, the structural damage per unit of payload does not change significantly for moderate increases in payload above the nominal value. Finally, on the basis of these results, recommendations are made for haul route design and operational practices which will increase the structural fatigue life of haul truck frames.

Jan 1, 1986

By E Jak

A viscosity model has been developed for both completely liquid and heterogeneous, partly crystallised slags in the Al2O3-CaO-æFeOÆ-SiO2 system in equilibrium with metallic iron. The Urbain formalism has been modified to describe the viscosities of the liquid slag phase over the complete range of compositions and a wide range of temperatures. The Roscoe equation has been used to describe the effect of presence of solid suspension (slurry effect) on the viscosity. The parameters of the viscosity model were optimised to describe large experimental data set in the low-order subsystems, as well as in the multi-component system. The computer package FACT was used for prediction of the proportion of solids and the composition of the remaining liquid phase. The model provides a good description of the experimental data (over four thousand experimental points) in liquid phase, and liquid + solid mixtures, over the complete range of compositions and a wide range of temperatures. This model can now be used for viscosity predictions in industrial slag systems. An example of the application of the new model to slag cleaning and reduction smelting processes is given in this paper.

Jan 1, 2000

Excavation through fill material in underground metalliferous mines is usually avoided where possible, unlike in Civil Engineering application where excavation through soft ground is normally a matter of course. In the mining situation, where excavation is normally for access only, then excavation designs are engineered for mining in hard rock, except where previous lack of forward planning has made such excavation inevitable or a mining strategy sequence necessitates some mining through fill in order to achieve optimum recovery of ore. Historically, this has been the case, because of the lack of knowledge of the support characteristics of the fill material placed underground and the lack of knowledge of the composition of the fill material as placed. The expertise and experience available from mechanised excavation techniques in Civil Engineering application (shield jacking, forepoling, spiling, and soft tunnel boring, to name a few) are available for application to the underground mining situation if the need ever arises. This paper describes the situations in underground mining development where mining through fill material is required, the different types of fill material encountered and the types of support available

Jan 1, 1981

The major incentives for developing continuous processes for the production of formcoke are to achieve a wider range of coals which can be used, greater operating flexibility enabling the production of various coke qualities, and environmental improvements. The characteristics of a formcoke which must be considered when assessing its performance in the blast furnace are compressive strength, abrasion resistance, volatile matter, reac- tivity, porosity, density, size, shape, ash yield and sulphur content. Lurgi's development work in attempting to pro- duce a formcoke which meets the specified requirements has resulted in most current efforts being concentrated on the Bergbauforschung/Lurgi hot briquetting process. This process blends hot char produced from a non-caking coal with small quantities of caking coal in a special mixer in the plastic range of the caking coal. The material is subsequently briquetted hot, then subjected to a thermal after-treatment to produce a strong abrasion resistant formcoke. A 650 tonne per day plant for British Steel Corporation is now under construction. A study of the equipment requirements and the operating costs indicate that the economics of large scale formcoke plants compare favourably with those of conventional coke-making plants.

Jan 1, 1975

By K Thompson

The Diavik Diamond Mine is a world-class operation located in an extreme environment 220 km south of the Arctic Circle in CanadaÆs Northwest Territories. The mine has a number of distinctive characteristics û such as limited winter access via an ice road, mine infrastructure being located on an island, with mining taking place behind dykes holding back a lake, temperatures at the mine that get down to -45¦C in winter, and the presence of bears, wolves, foxes and wolverines! One thing that Diavik does have in common with other mines around the world is the need for reconciliation. In late 2005 Diavik implemented SnowdenÆs Reconcilor software system to facilitate the process of reconciling geological models, mine plans, production data and plant results. This paper provides a case study of the reconciliation system implementation. It outlines the migration of Diavik away from a comprehensive and effective spreadsheet-based reconciliation process to a commercial grade, automated and web-based information management system. This paper documents the reasons for moving away from the spreadsheet system, the key parameters used for reconciliation, and the benefits gained by closing the loop between reconciliation and ongoing process improvement.

Jan 1, 2006

By Phillips D. N, Herbert H. K, Fletcher A. C, Lewis R. K

Quartzite is a common feedstock used for the production of silicon by reduction at high temperatures in a submerged electric arc furnace. Silica fume, formed as a by-product in this process, contains crystalline silica in the respirable fraction. The crystalline silica in the fume represents entrained quartz derived from unreacted quartzite raw material within the furnace. A knowledge of the fragmentation of quartzite feedstock, in response to thermal disaggregation in the furnace, is important in feedstock selection to help minimise (a) the amount of crystalline silica in fume, critical from an occupational health and safety perspective, and (b) impurity levels necessary to achieve the highest possible purity of product silicon. In this study, a series of quartzites has been assessed in terms of the above requirements and correlations drawn between mineralogical and chemical characteristics. Alkaline solubility correlates with grain-size and level of stored strain in the quartz matrix. Grain-size affects the surface area available for attack while stored strain enhances the chemical reactivity of the strained matrix as well as profoundly influencing the disaggregation and microfracturing characteristics of strained grains and, hence, available surface area for chemical reaction.

Jan 1, 1995

By Yianatos J. B

The advances in the study of control alternatives for flotation columns are reviewed. An integral solution to the control problem has to deal with problems associated with instrumentation, process modelling, control strategies and control algorithms. The term hierarchical control is used here to mean the intelligent integration of available knowledge, control algorithms and logic rules of decision. The selection of information, algorithms and rules is based on the experimental and theoretical knowledge of the column flotation process. The software support was designed and implemented in object oriented computer programs. This technique allowed the implementation of a combination of control techniques, algorithmics and heuristics, in the form of a control strategy. This strategy has shown to fit well with processes exhibiting complex dynamic characteristics. The hierarchical control was implemented in a pilot column and included the following general aspects: co-ordination of distributed conventional control loops, use of sets of control parameters for the froth depth control loop according to the froth depth state, verification and diagnosis of sensors, on-line predictive estimation of gas hold-up, diagnosis of common operating problems and the use of predictive control to account for feed flowrate changes.

Jan 1, 1995

China has abundant bauxite resources, but these resources are mostly of a diaspore, which has a feature of low Al2O3 to SiO2 mass ratio, typically ranging from four to six. Compared to other materials, this kind of raw materials consumes more alkaline and energy in the process of metallurgy, and incurred a high alumina production cost. To solve this problem, researchers in China have done a lot of work on removing of the silicon from bauxite. Under the impetus of these works, in 2003, the first flotation plant of diasporic bauxite in the world was constructed in Zhongzhou, Henan, China. Seven years of operating experience shows that this technology can signifi cantly reduce the costs of following-metallurgy processing. These efforts are an important reference for the processing of similar resource. In general, for Western scholars it is diffi cult to fully understand these works because most of them are published in Chinese. In this paper, a detail introduction for the research progress on China bauxite de-silica flotation was presented, these works involved crystal chemistry, wettability of bauxite minerals, collector and modifi er in bauxite fl otation and flotation practice, etc.

Sep 13, 2010

By McCarthy P. L

A distinctive feature of the goldfields of Victoria was the extrac- tion of gold from deep leads, that is the buried river beds of Vic- toria's ancient rivers and streams. It is estimated that about 265,000 kg of gold was produced from Victoria's deep lead mines which comprises about 11.5% of Victoria's total production of gold (Bowen, 1974). The significance of deep lead mining for Victoria, however, went far beyond its economic contribution to Victoria. If Profes- sor Blainey is correct it was the frustrations of mining gold from deep alluvial leads in Ballarat during 1854 which precipitated the Eureka Stockade (Blainey, 1963, 46-52). This event resulted in the implementation of a fair mining administration and was an emphatic statement of the rise of democratic movements in Australia. Much of the technology and skill for mining deep leads had to be developed locally because at that time no other major gold- field elsewhere in Australia or the world had gold deposits with comparable problems. Deep lead mining in Victoria was there- fore largely a home grown industry and the equipment for that industry was often designed and produced in Victoria.

Jan 1, 1988

By Hagan T. N

Quite apart from economic considerations, the following performance parameters must be considered when selecting an explosive for a particular blasting operation. 1. total energy yield/kg, and more particularly, strain energy/kg and bubble energy/kg of charge 2. charge weight/m of blasthole 3. sensitivity of the charge 4. water resistance of the charge The effective division of an explosive's total energy into strain energy (SE) and bubble energy (BE) is explained as is the influence of each energy component on blast results. Because some rocks require a high strain energy for effective breakage, while others are most satisfactorily fragmented by bubble energy, values of SE and BE are more meaningful than those of total energy. Unfortunately, our extensive knowledge of the effects of certain variables on total energy has not yet been completely supplanted by the influence of these variables on SE and BE values. Relative SE/kg and BE/kg values are presented for a range of explosives. The 'charge density of ammonium nitrate/ fuel oil (ANFO)-type explosives is essentially constant throughout the length of the charge; because of their compressibility, slurry

Jan 1, 1974