Search Documents

By H Ishikawa, S Palaniandy

The gravity-induced stirred mill such as the TowerMill is an energy-efficient grinding solution used in secondary, tertiary, and regrinding duties in the mineral processing concentrator. The interest in this technology is emerging, with more than 300 mills installed globally in various grinding duties and commodities for the last 30 years. Although the technology is matured, there are still opportunities for improvement and the development of new knowledge to improve its circuit energy efficiency and reduce water consumption. Recent studies show that a combination of stress intensity, ore hardness, slurry density, and mill feed configuration can be used to evaluate the performance of the grinding circuit. A recent pilot-scale TowerMill test work at various stress intensities shows that a lower operating work index and size-specific energy were achieved at higher agitator tip speed and using medium size grinding media. These outcomes were confirmed through several site trials. A smaller 17 mm grinding media has reduced the operating work index and size-specific energy by 18 per cent and 11 per cent, respectively, compared to the 20 mm in a magnetite concentrator. Moreover, the conversion from top feed to bottom feed configuration has reduced the operating work index and size-specific energy by 13 per cent and 37 per cent, respectively. The circulating load was reduced by 34–38 per cent, leading to a reduction in the dilution water consumption in the hydrocyclone feed sump by 20 per cent. A variable frequency drive offers flexibility to change the stress intensities on the TowerMill, where a 35 per cent reduction in specific energy was achieved when the ore became soft. This paper explores the potential design and operating strategies that can be implemented to enhance the energy efficiency, reduce water consumption and reduce CO2 emissions in the circuit and finally evaluate its impact on the total cost of ownership.

Aug 24, 2022

By E Hawkins, S Sheldon

Block caving is becoming a more widely adopted mining method allowing for underground massive low grade orebodies to be extracted economically. Underbreak during cave propagation is difficult to predict in terms of recovery and is not well-researched due to the small number of caving operations. During mining of E26 Lift 2 (E26L2) block cave at CMOC Northparkes Mines, a wedge of high grade material failed to cave, even with the assistance of preconditioning and subsequent attempts to induce caving. The ultimate solution for recovery of the uncaved wedge was the establishment of the E26 sublevel cave (SLC), which commenced mining in 2015, with production following in 2016. The SLC provides approximately 1Mtpa to supplement the lowering grade of the current E48 block cave feed. Applying the sublevel caving methodology to recover block cave underbreak has proven challenging. The impact of the caving stresses and preconditioning of the wedge have caused production limitations requiring continual remediation throughout production of the E26 SLC. The dependence on remediation work created a roadblock to implementing precharging as the prevalence of brow loss raised concerns over the inability to hook up the charged ring. In 2018, a wireless initiation trial was completed in the E26 SLC over 24 rings. The trial showed that precharging was achievable in this environment and greatly improved the safety of charge up personnel.

Mar 15, 2021

By J Taylor, M Smith, A Tunnadine, D Nikolakopoulos

As Olympic Dam rapidly expands into the Southern Mine Area (SMA) the Mine Geology team has concurrently ramped up underground diamond drilling to sustain rates of above 175 km/a. With >10 underground rigs double-shifting, traditional paper sections used for the management of drill programs were no longer optimal due to scale of operations. An opportunity was identified to modernise monitoring of all underground diamond drill programs, through the integration of logged copper sulfide estimates with Olympic Dam’s first-fully integrated deposit-scale geological model in Leapfrog Geo. This paper describes the transition within the Mine Geology team from reliance on 2D paper sections, towards near-real time 3D geological modelling for optimising end-of-hole decisions in the field. This transition was enabled by innovative database solutions informing locally constrained implicit models, limited by a distance buffer around active underground fan drilling. Due to the high volume of historic drilling, there were significant computational challenges with the implementation of daily production style implicit models at Olympic Dam and initial testing of regular updates to implicit gradeshells and sulfide domains required in excess of 12 hrs to run. The enabling solution was to optimise the interfaces between the AcQuire database, Deswik MDM and Leapfrog Geo to create a dynamic, streamlined workflow that was easily completed by Mine Geologists in accordance with daily production duties. Geologists are now building rapid implicit models for a range of variables from an integrated data set of logged sulfide estimates and existing assays, spatially constrained by 150 m buffers around active drilling using a unique drill fan identifier flagged during the planning phase. Once the live-implicit models are updated, they are exported for visualisation on field tablets to be used during logging and core checks at the start and end of every shift. To manage the risk of ‘going digital’ interpretation remains at the forefront of the drill section close-out process, with Mine Geologists critically reviewing the finished sections on a standardised template with new learnings wireframed and communicated to stakeholders. The Live Field Model has enabled a step-change in the geological effectiveness of diamond drilling, reducing over – and under-drilling ore-waste at Olympic Dam continuing to push drilling effectiveness towards 20 per cent of intercepts >2 per cent Cu. In addition, upside or risk identified during the proactive management of drilling execution can be rapidly capitalised or mitigated.

Mar 22, 2022

By A E. Waltho, W J. Shaw

Predicting the physical characteristics of various ore types has for long been a difficult problem during mining. Grade control practices tend to concentrate on the chemical grade of the ore. Estimation of physical characteristics such as beneficiation behaviour is commonly limited to the simplistic application of historical averages. Large amounts of geochemical data are often gathered during the exploration and mining stages of a project, especially in ferrous and base metal deposits. In addition to the elements of principal economic interest, samples are often analysed for suites of gangue constituents to determine whether the mineralisation lies within target specifications. This multi-element data is often put to no other use than this simple chemical classification, yet it may present the geologist or metallurgist with valuable insights into the mineral content and physical characteristics of the deposit. Normative mineral estimates have been used as a method for characterising igneous rocks for almost 100 years. The method establishes and applies a set of sequential rules, by which the chemical components of a sample are assigned to mineral components. Provided that it is possible to make some realistic assumptions about the mineral species likely to be present in a rock unit or deposit and their paragenesis, this approach can be extended to a variety of mineral deposits. The geochemical data that are routinely collected when, for example, drilling iron ore and base metal deposits, can be used to derive estimates of normative mineral content. These estimates can be used to characterise physical or metallurgical aspects of the ore, such as density, beneficiation behaviour and metal recovery. This paper examines the application of normative mineral estimates to a variety of practical resource characterisation problems. The potential for predicting the lump and fines proportions of iron and manganese ores is also discussed.

Jan 1, 1999

By R Morrison, R Dunn

In many mineral processing operations, the reported production figures for an accounting period may not make the best use of available data. While most of the mathematical approaches, such as check-in/check-out, mass balancing, used in effective metallurgical accounting strategies are well understood, the sources and magnitude of measurement errors generally are not. As part of the æAMIRA P754-Metal Accounting and ReconciliationÆ project, a study was undertaken at the Northparkes copper/gold concentrator near Parkes, New South Wales to examine the data used in their concentrator metallurgical accounting system. This paper summarises the results of a detailed examination of the mass measurement systems around the concentrator as well as the primary sampling system used for grade estimation. The goal of this work was to develop practical techniques to quantify the error (ie both accuracy and precision) of the measured metal accounting information. With this information, statistical confidence levels for this data can then be calculated. If the errors are small, the effect of error in each piece of measured data can then be propagated to other calculated production figures such as recovery and feed grade using a statistical technique called æthe propagation of errorÆ.

Jan 1, 2007

By B Firth, G OÆBrien, B Jenkins

In coal flotation, particles of different components of the coal such as maceral groups and mineral matter and their associations have different hydrophobicities and therefore different flotation responses. By using a new coal grain analysis method for characterising individual grains, more detailed flotation performance analysis and modelling approaches have been developed. The method involves the use of microscopic imaging techniques to obtain estimates of size, compositional and density information on individual grains of fine coal. The density and composition partitioning of coal processed through different flotation systems provides an avenue to pinpoint the actual cause of poor process performance so that corrective action may be initiated. The information on grain size, density and composition is being used as input data to develop more detailed flotation process models to provide better predictions of process performance for both mechanical and column flotation devices. A number of approaches may be taken to flotation modelling such as the probability approach and the kinetic model approach or a combination of the two. In the work reported here, a simple probability approach has been taken, which will be further refined in due course. The use of grain data to map the responses of different types of coal grains through various fine coal cleaning processes provided a more advanced diagnostic capability for fine coal cleaning circuits. This enabled flotation performance curves analogous to partition curves for density separators to be produced for flotation devices.

Jan 1, 2005

By H Benzer

Grinding clinker to finished cement consumes more energy than any other comminution process. World production of cement in 2009 was 2840 million tonnes and the energy required for comminution was 40-60 kWh/tonne depending on the clinker characteristics and the fineness of the finished cement. Machines used include single and multi compartment ball mills, HPGRs, vertical roller mills, centrifugal air separators, V separators, screens and crushers. The circuit most commonly used consists of a closed circuit HPGR followed by a single compartment ball mill and an air separator, and in operation the variables are adjusted to obtain maximum throughput with no loss of quality of the separator fines.A common objective in cement plants is to reduce energy consumption without affecting the particle size in the finished cement and simulation is used as one procedure to achieve this. Models are now available for all the machines commonly used in clinker circuits and circuit optimisation studies using simulation have been carried out in many plants leading to decrease in energy consumption per tonne of cement. In this paper the models used will be discussed briefly and several case studies will be reviewed which will highlight the effect of change in ball size in a two compartment mill, the role of the HPGR in an HPGR – ball mill – air separator circuit, and the use of a high intensity vibrating mill for producing finished cement with high additive ratio.

Aug 8, 2011

By A V. Ozsever

The selectivity in flotation columns involving the separation of particles of varying degrees of floatability is based on differential flotation rates in the collection zone, reflux action between the froth and collection zones, and differential detachment rates in the froth zone. Using well known theoretical models describing the separation process and experimental data, froth zone and overall flotation recovery values were quantified for particles in an anthracite coal that have a wide range of floatability potential. For highly floatable particles, froth recovery had a very minimal impact on overall recovery while the recovery of weakly floatable material was decreased substantially by reductions in froth recovery values. In addition, under carrying-capacity limiting conditions, selectivity was enhanced by the preferential detachment of the weakly floatable material. Based on this concept, highly floatable material was added directly into the froth zone when treating the anthracite coal. The enriched froth phase reduced the product ash content of the anthracite product by five absolute percentage points while maintaining a constant recovery value.

Jan 1, 2005

By X Hu, C-C Yang, J Pan

In this work, preheating and roasting tests of pellets made from blends of Western Australia ultra-fine (WAU) magnetite concentrate and Chinese domestic magnetite concentrate or Brazilian hematite concentrate were carried out. The results showed that pellets made from 100 per cent WAU magnetite concentrate possesses inferior preheating and roasting performance when preheating at 1050°C for 20 minutes and roasting at 1300°C for 40 minutes, the compressive strength of preheated and fired pellets is 502 N/pellet and 2313 N/pellet, respectively. When 40 per cent Chinese domestic magnetite concentrate or 20 per cent Brazilian hematite concentrate was blended with 60 per cent or 80 per cent WAU magnetite concentrate, the appropriate preheating temperature of the pellets are reduced from 1050°C to 950°C and 975°C, and also the firing temperature of two types pellets are decreased from 1300°C to 1250°C and 1280°C respectively. Moreover, the compressive strength of fired pellets is obviously improved up to 2746 N/pellet and 2630 N/pellet respectively. Microstructure analysis of the fired pellets made from 100 per cent WAU shows its poor growth of Fe2O3 grains, low interlinkage degree of hematite grains, small size of crystallised grains and high porosity of pellet; however, the fired pellets that blended with domestic magnetite concentrate or with Brazilian hematite concentrate have fully growth of Fe2O3 grains, closer interlinkage of hematite grains, lower porosity and stronger consolidation. The preheating and roasting performance of WAU magnetite concentrate pellets can be improved by optimising ore matching.CITATION:Pan, J, Hu, X, Zhu, D-Q and Yang, C-C, 2017. Pelletising performance of Western Australian ultra-fine magnetite concentrate and strengthening technique by optimising ore matching, in Proceedings Iron Ore 2017, pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By G Milligan

This paper describes how water is being planned, managed and used in Queensland as both a precious natural resource, vital for healthy ecosystems, and as a valuable tradeable commodity, necessary to secure economic prosperity. Queensland has been progressively implementing a planned package of water industry improvements agreed by the Council of Australia Governments in 1994. The Water Act 2000 provides the legislative basis for implementing the COAG water reform framework in Queensland and sets out statutory water planning processes. A Water Resource Plan (WRP) is a strategic document that specifies water sharing and environmental flow outcomes across a whole catchment over a period of up to ten years. A Resource Operations Plan (ROP) sets out the details of implementing a WRP, including environmental flow rules, establishment of tradeable water allocations that are separate from land, rules for water trading, rules for operating water infrastructure, arrangements for the release of any unallocated water identified in the WRP, and requirements for monitoring and reporting. Water Resource Planning and Resource Operations Planning are progressing in priority catchments and aquifers across the State. Ways to obtain a water entitlement now depend on whether a WRP and/or a ROP exist in a particular catchment. Water trading provides for the buying and selling of water entitlements on a permanent basis where permitted under a ROP. Details of tradeable water allocations are securely registered on the Water Allocations Register, which is similar to a land titles register. Leasing and temporary transfers of water entitlements are also possible. Water brokers are emerging to facilitate water trading which aims to improve water use efficiency and move water to higher value uses. Queensland is leading the way in the implementation of the COAG water reform framework and the pursuit of sustainable water resource management. The StateÆs progress in this regard is increasing certainty for water users, while ensuring that considerations of equity amongst existing and future users and amongst various uses, as well as considerations of ecological sustainability and the wider community, are all taken into account. The mining sector stands to benefit substantially from these new approaches to planning, managing and using this precious resource.

Jan 1, 2003

By T N. Little

The author contends that geoscience is presently under-utilised in the rock fragmentation by blasting process. Before we can set standards in this area, the following is required: mine geologists need to gain a better understanding of the blasting process and the blasting team needs to obtain a better appreciation of geology. Both groups need to be informed of what can be done to improve blasting outcomes, why it is necessary and how it can be achieved. By working closely together, both the geoscience toolkits and blasting expertise can be applied and focused on priority blast sensitive issues, with potential to improve mine economics and safety. Finally, and ideally, mine geologists need to take a leadership role in raw rock mass data collection and data management, and invited to take an active role in rock mass related behaviour data collection, integration and presentation.This paper attempts to provide insight into all these prerequisites for setting a new standard for collaboration and mutual learning in this strategic opportunity area. The potential for blasting to leverage downstream processes is highlighted. Blasting objectives and blast design principles are introduced along with the required rock mass related inputs. Some hazardous geological materials and environmental conditions are described, along with how they can affect operational complexity.Four case examples are used to illustrate the need for closer liaison between geology and blasting professionals. The first related to grade control blasting, aims to demonstrate how a blasting geology approach can add significant value. Case example two demonstrates how geological models and bench face analysis can assist with fragment control. The third and fourth case examples involve an overview of two case studies where timely geological and geotechnical knowledge input and intervention into blasting activities may have reduced losses due to blast initiated open pit slope collapses.CITATION:Little, T N, 2017. Geoscience input into blasting operations – let’s set a new standard, in Proceedings Tenth International Mining Geology Conference 2017, pp 375–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By W T. C Kendall, H D. Ngo

Garden Well is a shear-hosted Archaean orogenic gold deposit located 100 km north of Laverton, Western Australia. The Garden Well processing plant is designed for a nominal 491 t/h milling rate and annual capacity of 4 Mt. The plant has three key innovations:1. a scrubbing circuit, expected to reduce grinding power consumption by up to 20 per cent2. a secondary cycloning/gravity circuit, providing a second opportunity for gravity gold recovery (additionally, the circuit effectively increases the leach residence time of the coarse gold bearing fraction of the leach feed by approximately 60 per cent, without any additional tankage)3. the use of mid-stream oxygenation to enhance gold recovery.The Garden Well deposit is free-milling with overall laboratory gravity/leach gold recoveries exceeding 95 per cent at a P80 grind size of 150 ¦m. Three mineralogical domains have been identified: oxide, transition and fresh, with the fresh domain having subdomains of fresh ultramafic and fresh shale. There is a high component of gravity recoverable gold in all three domains.This paper will discuss these innovations and the design challenges and the risk mitigation strategies that were adopted to ameliorate the prototyping risk. The performance of the plant since commissioning together with lessons for the future will also be presented.CITATION:Smith, R J, Kendall, W T C and Ngo, H D, 2013. Treatment plant innovation at Garden Well, in Proceedings World Gold 2013 , pp 315-324 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By J Gould, T Elkington

Mine operation strategies are commonly optimised with a net present value (NPV) maximisation objective. There are well known properties of a typical mining project optimised for NPV, including high production rates and declining cut-off grade schedules. In practice, however, frequently there are operations that diverge from such NPV-maximising properties. Although a range of reasons for this can be at play, one possible explanation is that operators intuitively adjust their strategies to compensate for the flaws inherent to NPV maximisation. In particular, NPV analysis does not reflect the benefits of managerial flexibility inherent in a mining plan. Real options valuation (ROV) is an alternative approach that addresses this issue. We compare the properties of NPV and ROV optimisation solutions generated for the same scenario. Our simple case study demonstrates that the presence of real operating options in the optimisation model not only entails increased project value as expected, but also tends to encourage lower processing capacity (with lower associated capital cost), higher cut-off grades and greater use of stockpiles.CITATION:Elkington, T and Gould, J, 2012. Real option value optimisation, in Proceedings Project Evaluation 2012 , pp 35-40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By A R. Sale

This paper highlights two aspects of the mineral sands industry in Australia: the development of the industry from approximately 1870 through to 1980, and the author’s experience in the industry from 1966 to date.The first real heavy mineral (HM) mining in Australia started in 1870 with the mining of heavy mineral slicks on the beaches along the east coast of Australia. The real potential of Australian heavy minerals was however only realised in the 1920s with the first production of a heavy mineral concentrate that was shipped to Canada for processing. Post WW 11 and the Korean War, Australia was the largest producer of mineral sands products in the world as well as a significant developer of associated separation equipment and technology. The number of producing companies in the east coast peaked at 33 in 1957, was reduced to ten by 1965, and subsequently further reduced to five in 1980 as a result of potential mining areas being declared National Parks or Conservation Reserves. Today there is one company, Unimin Australia Pty Ltd (formally Consolidated Rutile Ltd) operating on the east coast. In contrast there were three companies on the west coast in 1965, four companies in 1980, and four companies today (albeit not the same companies).There have been considerable ups and downs for the industry in Australia, however world wide it was renowned in the past as being an industry that attracted numerous interesting and innovative characters that played a major role in developing it into the vibrant industry that it is today. This, given the current climate, is predicted to continue into the future.The author has been continuously involved in the industry for over 45 years from 1966, initially as an electrician at Consolidated Rutile Ltd culminating in the role of General Manager/President of Iluka Resources Limited USA, prior to his retirement in 2009. His exposure has been world wide and has covered all aspects of the industry but in the main focused on project development and operational areas. During this time there have been significant technological advances, yet to some extent the basic principles have not changed at all. Some of the most noteworthy advances include the development of the Wright Spiral in 1977, the development of the Reading High Intensity Wet Magnet (WHIMS), the rare earth magnets, the CRL floating thickener and the improvement of analytical techniques. From a safety, health and environmental perspective there has been significant advances that the industry has much to be proud of. These include wetland restoration both in Australia and in the US, the restoration of farmland in Virginia and Capel, and the re-establishment of native species, for example at Eneabba and Richards Bay to name but a few.

Oct 5, 2011

By J Li, J Regan, D Payne

The Caval Ridge Mine is an open cut coalmine and located within the Bowen Basin region in Central Queensland, and commenced mining and processing operations in 2014. A number of geotechnical challenges for managing dragline bench and lowwall stabilities have been encountered in both southern and northern pits over the years. Southern Pits contain steep seam dips of up to 15° (27 per cent) whilst the northern pits also have shears below pit floors. Geotechnical guidelines to manage the risk of dragline bench failure and lowwall instability have been developed and improved since these geotechnical challenges were identified. The dragline guidelines include dragline tub offset distances from the 60° Line (SDL) or buttressing thickness for different seam dips greater than or equal to 8°. The low wall stabilisation guideline established floor disruption widths and depths depending on seam dips and presence of floor shears to known depths of up to 3 m. As mining operations advance, lowwalls have remained stable until floor disruptions were fired, then returned to stable soon after the shot. The maximum distance of lowwall cracking with blasting has been as far back as the second spoil peak (the prestrip truck dumps construction limit). These failures need to be eliminated to allow the operational flexibility and haulage benefit of constructing the prestrip truck dumps behind the first spoil peak, while maintaining no risk to personnel or equipment. The floor shear depth was verified by collaborating with the exploration teams and taking advantage of the already planned 8-inch coal quality core holes, drilling them an extra 5–10 m past the coal seam floor and locating the shear presence. With this continuous improvement effort, no lowwall failures have occurred during floor disruption firing from the second strip after the new floor disruption depth guidance have been applied. This paper documents the processes for developing these geotechnical guidelines, operational implementation, and outcomes. Operational applications over the years confirmed that these guidelines have effectively managed the dragline bench and lowwall failure risks related with the steep seam dips and floor shears in this open cut coalmine.

Nov 29, 2022

By Q Fan

The steelmaking desulfurisation plays an important role in coal-based steelmaking route of blast furnace and BOF converter within the flow sheet of BF-deS-BOF. With the advent of H2-based ironmaking and steelmaking process, the transition flow sheet of DRI-Smelter-BOF has been assessed and developed by the steelmaking industry. What is the role of deS in H2-based route of DRI-smelter-BOF? This paper will present the influence of sulfur-containing iron ore on steelmaking desulfurisation and the leading role of EAF-smelter played in H2-based steelmaking route. The sulfur contents of iron ore vary considerably around the world and lower-grade iron ores with high sulfur are likely to be used for H2-based route, a considerable amount of sulfur that comes from DRI will report to the melt of EAF-smelter and the operating conditions of EAF-smelter also impact the sulfur content of the hot melt for steelmaking deS. The EAF-smelter of H2-based route is the focus of the steelmaking industry at moment, unfortunately, an industrial-scale EAF-smelter has been the missing link of the flow sheet of DRI-Smelter-deS-BOF, despite similar EAF-smelters being used for various applications of Fe-Ti and Fe-Ni processes. The latest progress is that several pilot-scale and industrial-scale EAF-smelters with reducing capability are planned for construction within next several years and low-grade Australia iron ores are certainly to be employed as basic feedstocks for H2-based route of DRI-Smelter-deS-BOF.

Sep 18, 2023

By G C. Snedden

Tandem row stator arrangements are common in the last stage of multirow, gas turbine compressors. Tandem row stators, or stator and de-swirler vane combinations are used to relieve the loading on the stator but ensure axial flow leaving the compressor. In this paper a standard 40” (1016 mm) ventilation fan in the Air Blow Fan’s range is modified to utilise the plate support struts on the barrel to relieve the aerodynamic loading on the aerofoil stator. Performance maps for both versions of the fan were generated using computational fluid dynamics and are compared across a wide range of rotor setting angles showing a clear advantage of approximately 2 per cent in efficiency for the tandem blade design. In addition, the area of high efficiency that represents the practically usable area of the map extends over a greater area in terms of flow rate and total pressure rise.

Oct 12, 2022

By S H. Burgmans, B Anderson

This paper aims to define the specific challenges relating to dredging fine tailings from an above ground storage facility for transferral to a mined-out pit. In addition, it compares dredging and mining perspectives on dredging of fine tailings.

Jul 1, 2021

By C Jenkins, M Mativenga, C Stanton, J Gerber

In 2014, Arrium completed an optimisation program on its magnetite concentrator, enabling a reduction in the overall cost base of producing concentrate through an increased ability to treat a wider range of ore types, previously considered waste. The development was the culmination of four years of work, conducted in house by Arrium’s mining development group. The overall intent of the plant design focused on improving the concentrator’s ability to treat a wider range of magnetite ore types. Metallurgical analysis of these feed ore groups outlined a need for more grinding power if production quality was to be maintained and throughput increased. As such, a tertiary grinding circuit was designed which, alongside the rectification of key operational bottlenecks, would allow the plant to continue to produce concentrate at the required specification and rate. The technology chosen for the tertiary grinding application was the XT IsaMillTM, which is known for efficient fine grinding when compared to conventional ball milling. The transfer sizes between the existing comminution circuits were coarsened, allowed for the treatment of different ores at the required rates. The optimisation project was successfully completed in February 2014 after a three month commissioning phase. The initial metallurgical testing and engineering of new equipment proved highly successful with all equipment meeting or exceeding design parameters.CITATION:Stanton, C, Mativenga, M, Gerber, J and Jenkins, C, 2015. Unlocking plant capability through targeted debottlenecking of Arrium’s magnetite concentrator, in Proceedings Iron Ore 2015, pp 185–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

This paper reviews hydrometallurgical processing technology for refractory gold ores, which form an increasing resource stock for gold. The reasons fQr ore refractoriness and pressure, chemical and biooxidation process options are briefly listed. Electrochemical technology, suitable for processing refractory ore is reviewed and some preliminary results for the electrochemical oxidation of slurried arsenopyrite are given.

Jan 1, 1992