Search Documents

By P Craig, M Holden, C Zhang, D Foster, J Oh, S Saydam, J Liu, H L. Ramandi, S Akdag

High stress in rock masses can cause significant instability problems such as squeezing deformation in soft rock and rock bursts in hard rock. The support system applied in burst-prone areas in high-stress conditions is required to be able to carry high load and accommodate large deformation of the rock mass without experiencing any serious damage. Yielding support systems are promising to provide support for both squeezing and burst-prone rock mass encountered in mining or tunnelling at depth. They are ideally strong and stiff initially and then ductile after yielding (Potvin and Hadjigeorgiou, 2020). With respect to support design, a ground support system has to create a safe working environment under both static and dynamic loading conditions by providing the functions of reinforcing, retaining, holding and connecting elements (Cai and Kasier, 2018). Rigid rock bolts and cable bolts perform reinforcing and holding functions of a ground support system. In highly fractured ground or with large excavation spans (eg at roadway intersections or in caverns), unstable ground depth can exceed the length of typical rigid rock bolts (ie greater than ~3.0 m). In such cases, flexible cable bolts are needed to tie the reinforced and retained rock mass back to deeper and more stable rock. The flexibility of cable bolts allows anchor lengths greater than the tunnel opening that would otherwise restrict rigid bolts. Cable bolts also offer higher strength to weight ratio, with tensile strengths 2–3 times that of standard rebar bolts. This high strength comes at the cost of lower strain tolerance, typically around 5–7 per cent at break. Despite the lower strain tolerance, cable bolts are often used as dynamic support in demanding burst-prone ground conditions. The lower strain tolerance is compensated by allowing sufficient free length for stretching or incorporating a yielding device. There are a number of dynamic cable bolts available on the market and a number of testing campaigns have been undertaken to quantify the dynamic performance of these cable bolts. This paper reviews the existing range of dynamic cable bolts and discusses the potential areas for improvement and further research.

Nov 29, 2022

There is no doubt that the mining sector is considered to be the backbone of many countries. Furthermore, it has played an important role in the prosperity of nations, whether developed or developing. Saudi Arabia is one of these countries that has a large variety of metallic and non-metallic mineral resources that range in size and value occurrences of limited potential to deposits large enough to sustain profitable exploitation. Therefore, the Saudi government needs to reinforce the capacity of the sectoral institutions to better regulate and promote the sustainable development of the sector. The ability to overcome the administrative and legal complications that constrain private sector participation in the minerals sector, through new mining code which will streamline the procedures for obtaining licenses and will add more predictability and transparency to the application process, are proposed for increasing the sustainable development. This paper will outline how the Saudi government is tackling the major challenges that face the minerals industry. This paper provides the background to the Saudi Arabian mineral sector and its industrial base. Finally, the paper identifies the problems and constraints that face the minerals sector in Saudi Arabia and provides an assessment of the effects of government policies and planning efforts in the minerals sector, particularly during the period of the development plans which started in 1970.

Jan 1, 2009

By T Alexieva

Since the early 1900s the geotechnical community has investigated every significant failure of a tailings dam, improved our knowledge of the behaviour of the tailings storage facilities, developed analysis methods, compiled lessons learned, and committed to zero failures. The rate of occurrence of tailings dam failures has reduced since the 1980s, however, failures continue to occur and continue to surprise us. At BHP, we have decided to take an approach to the tailings management that is similar to the approach to safety. We are looking at ways to eliminate, substitute, separate or engineer around the hazard (tailings dam failure). As such, our ultimate long term goal would be to eliminate the need for new tailings facilities. Unfortunately, we have not developed yet technologies for extracting many of the common metals and minerals without producing tailings. Our shorter term goal is to substitute the current conventional slurry tailings facilities with less risky dryer facilities. We are working with vendors and research organizations to develop technologies that can be efficiently applied on a large scale. At the same time, we are committed to using the best available engineering to reduce the risks associated with our existing and new conventional tailings facilities. The best engineering can be achieved by people with the appropriate education, experience, attention to detail, discipline and authority. We have implemented a system of governance to make sure, we have the best engineering applied to all our facilities, considering the specific conditions at each site.This paper presents the current tailings governance process at BHP, and the initiatives that were undertook towards achieving a zero failure goal. CITATION:Alexieva, T, 2018. Tailings governance, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 2–7 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By T Roberts

The transition of mechanical cooling refrigerants from their inception in the 1800s through to the current day has been driven by several factors. Original refrigerants such as sulfur and carbon dioxide, chloromethane and ammonia, whilst effective came with toxicity and/or flammability issues. In 1930 DuPont trademarked a new synthetic refrigerant known as Freon® 12, this development was the introduction of ‘chlorofluorocarbons’ (CFCs).Throughout the 1930s and 1940s additional synthetic refrigerants were developed, namely Freon® 11 and Freon® 22. Due to their non-toxic and non-flammable characteristics, synthetic refrigerants were extensively used for domestic, commercial and industrial applications for the next 60 years.In 1985, one of the first scientific papers suggested a potential mechanism linking CFCs and areduction in the density of the ozone layer. In 1987 the Montreal protocol is ratified; it is the first UN treaty to be ratified by every country on earth. Due to CFC’s ozone depletion potential (ODP), the treaty required the consumption of CFC’s to be reduced by 50 per cent over the next ten years. By 1996 the phase out of CFC’s (Freon® 12) is completed, the phase out of HCFC (Freon® 22) refrigerants comes into effect.On 1 January 2018 the phase down of HFC’s begins. Whilst having zero impact on the ozone layer HFC refrigerants have high global warming potential (GWP). As we transition through the HFC phase down (2018–2035) we are beginning to see the emergence of what some consider to be the fourth synthetic wave, hydrofluoro-olefins (HFO’s). HFO’s and their blends have zero ODP and low GWP’s, ranging from 150 to less than 1. The reduction in GWP with HFO’s typically comes at the expense of flammability, which is not ideal. Each refrigerant has its optimal application, therefor when considering refrigerant choices for mining systems, a complete assessment of the environmental, health and safety, efficiency and commercial impacts should be considered now more than ever.

Oct 12, 2022

By T N. Little

This review paper presents an integrated and practical insight to blasting geology and its importance. This approach involves developing blasting objective up front and implementing geology specific blast designs. The author refers to this approach as ‘starting at both ends’. There are many human-imposed controls on blasting operations, such as: safety, security, legislative, company standards, heritage, and environmental constraints. Thus it is possible for some operators to lose sight of the controls imposed by nature. This paper demonstrates how site geology controls or influences many aspects of the rock breaking processes and how a focus on this aspect has potential to add considerable value to mining operations. It is obvious that mining companies concentrate their efforts on economic/ore geology (good rock geology). However it is the author’s experience that they also concentrate on engineering geology (bad rock geology) only when forced to do so by the ground conditions, but seem to run out of puff before they apply blasting geology (big rock geology). This paper contains five main sections. In the first section, the impact of geological controls on blasthole drilling is briefly discussed in terms of drill selection, penetration rates, bit wear, blasthole stability, blasthole deviation, and health precautions. In the second section the geological controls on aspects of geometric design are reviewed. These include: hazardous minerals, valuable minerals, selection of the blasting techniques, geological structures, blasting direction, and blasting geometry. Section three overlaps with the geometric design section and deals with aspects related to explosives. Topics addressed include selecting the explosive type based on geology, distribution of explosive charge in space and time, explosive performance, and the rock response to explosive loading. In the fourth section, examples are given of the operational complexity needed to implement a blast to cater for difficult bench geologies, environment constraints, past mining (voids) and need for a high degree of quality control. Section five demonstrates geological controls on blast results. Blasting results include the muck pile characteristics, downstream handling and processing, damage to the remaining rock, and blasting emissions.

Nov 8, 2011

By H Bateman, I Cawrse, G Carnes, S Cawrse

In developing mineral resources, the focus typically centres on the management of identified social and environmental impacts and compliance with regulatory requirements. However, opportunities to protect and enhance the environment and communities are most effective in the planning and design phases. Achieving the objective of integrating sustainability considerations as an element of design decision making requires that the design criteria be technically sound, relevant to the project and applicable to desired design outcomes. This is particularly important for projects employing virtual teaming, where design engineers may be geographically dispersed and are unlikely to be familiar with site specific sustainability challenges and opportunities. This paper documents the approach taken by BHP Billiton to incorporate sustainability principles, objectives and guidelines in design criteria for the Olympic Dam Expansion (ODX) project. It describes the range of inputs used in defining sustainability objectives which interface in a framework that is dynamic and transferable to other mining projects and to engineering design in general. The Sustainability in Design Criteria document distils statutory requirements, corporate standards, lessons learned and leading industry practice into a single coherent framework that supports engineers to approach problem solving as a holistic and integrated exercise with a long term perspective. The framework also serves to improve linkages between internal stakeholders by fostering greater communication, collaboration and innovation to deliver more sustainable outcomes through the design process.

Jan 1, 2009

By N Takamatsu

The environments surrounding the iron and steel industry have changed greatly in recent years. Reported in this paper are the technologies adopted by the Japanese iron and steel industry to fititself to change in global steel demands, degradation of iron ore and coal, prolonging service life of the facilities and requirements of energy saving. In addition, innovative technologies for CO2 emission control in iron making processes are also discussed.

Jul 11, 2011

By B Robertson

Over the 40 years that the author has been engaged in the Australian underground coal mining industry, there has been a continuous improvement in safety performance as the sector has grown in size and productivity. The underground environment hosts many hazards with significant risk profiles that are kept in check by effective health and safety management systems that have evolved largely following major underground disasters. Observations are made on the changes observed for specific aspects of the underground coal sector, with particular reference to ventilation issues, and predications are made as to the needs of the future.CITATION:Robertson, B, 2013. Past achievements and future challenges in the underground coal sector, in Proceedings The Australian Mine Ventilation Conference , pp 27-32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By X Tian, J Forster, A Olmsted, E R. Bobicki, M Goldbaum, D Boucher, C A. Pickles

As the global demand for metal values expands, it becomes increasingly important to create more sustainable mining operations. Consequently, considerable research and technology development is required to produce processes which are both more energy efficient and have a minimal environmental impact. One potential technology is the utilisation of microwave pre-treatment to reduce the energy requirements in comminution. Microwaves can preferentially heat the valuable mineral phases in an ore and the resulting differential thermal expansion leads to the formation of microfractures along the grain boundaries. As a result of the preferential heating, ore competency is reduced, mineral liberation is enhanced, a coarser grind size can be employed, and plant throughput can be increased. Furthermore, microwave pre-treatment can be combined with advanced ore sorting, to decrease the quantity of gangue material processed downstream and hence reduce tailings production. Previous studies on the microwave treatment of ores over the last 30 years have mainly been limited to low power bench-scale studies and there is a paucity of information on pilot and/or commercial scale studies. In the present research, the microwave heating behaviours of over 40 ores have been studied at the bench-scale. These results were used to generate a database, from which a unique classification system was developed. This system was used to rank the amenability of any given ore for microwave pre-treatment. This knowledge can be employed to predict the performance of the ores in the high-power pilot scale tests and thus can be used as a pre-screening tool. The effects of high-power microwave pre-treatment on grindability and liberation were reported. Additionally, the ore sorting potential was evaluated using a combination of X-ray transmission (XRT) and microwave infrared (MW/IR).

Aug 24, 2022

The Cadia Valley Operations currently hosts a large operational open pit, a large operational sublevel caving underground mine and two other underground projects at the study stage. This scenario creates an unusual situation for the evaluation and planning of a fifth major open pit project. The Cadia East Open Pit is a large gold-copper development located adjacent to the operational open pit and above one of the underground projects. A study team is conducting a comprehensive and robust analysis of the target orebody. Two key factors for this project include the existing and planned projects within the valley and the wide range of available mining methods. The aim for the study team is to present an optimal and practical case which suits the entire Cadia Valley Operation. A rigorous and robust analysis of the situation requires that each factor be properly evaluated. A modular system has been developed which allows the wide range of scenarios to be quickly and meaningfully considered. Sensitivities for each module drive the further development of that particular module. As each scenario progresses, an assessment is made evaluating its value, strategic value and practicality. In such a way, the number of scenarios is gradually reduced at each stage to produce a final short list of feasible cases. Each scenario on the shortlist is then assessed with regard to the existing operations and other projects. A qualitative and quantitative analysis is made. This ranking is used to provide the recommended case.

Jan 1, 2007

By A Roseman, T Gruber

Traditional methods for installing gaskets for segmented bored tunnels have relied upon different bonding procedures with adhesives that carry a series of disadvantages to segment producers. Fixation of the gaskets into the concrete segment as part of the casting procedure has been developed over the last 20 years and has emerged as an economical solution to produce high-quality tunnel segments for various technical tunnel applications. This paper investigates the advantages of using anchored gaskets, the different tunnel systems that employ anchor gaskets and reviews the first anchor gasket project; the Lee Tunnel and analyses how segment production efficiencies are gained.CITATION:Gruber, T and Roseman, A, 2014. Use of anchored gaskets in segmented bored tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 253–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The paper provides an overview of the development and content of APCOM symposia since their inception in 1961. This development is set within the context of the academic environment in which much of the research published at APCOM symposia is conducted. This environment includes rigorous external assessment of research quality at national levels and against international benchmarks, which carries significant consequences for funding and for the continued existence of the academic minerals industry disciplines. Adverse consequences that undermine the academic provision of mining and resource engineering will impact negatively on the minerals industry by reducing the level of research and education resources available to it.The traditional reductionist approach to research is contrasted with the inter-disciplinary approach that is required to address the complex systems problems that the minerals industry will have to address to ensure its technical, economical and environmental sustainability. Such an approach offers a means of raising research profiles, of establishing mutually beneficial academic-industry engagement and provides an opportunity for APCOM to take a lead role in identifying the research and development agenda for the future

Sep 26, 2011

By G J. Wilkie, P A. Revell

The R&D landscape for ore pre-concentration technologies within mining is characterised by the development of individual technologies and point solutions. This presents METS and mining companies with the combined challenge of understanding how to apply pre-concentration technologies to create maximum value, and how to sustainably integrate the technologies into their businesses to maintain the value. The paper will consider the requirements of an integrated pre-concentration system and presents a portfolio of R&D projects that have co-developed and integrated a suite of new precencentration technologies and methodologies across the mining value chain. Focus areas include in-situ orebody characterisation, blast design, real time cross belt mineral sensing, and consideration of how much data needs to be acquired in order to make value based decisions between ore pre-concentration options. An ore pre-concentration workflow is presented to demonstrate how additional optimisation opportunities are enabled both by moving decision points further upstream in the value chain, and by integrating the concepts of pre-concentration into the design of mineral processing equipment. Additionally, several research projects examine the non-technical factors that present barriers to uptake of new technologies within mining companies. Organisational culture, risk management and socio-political factors are discussed and a set of management tools are presented that allow organisations to self-assess their readiness for new technology uptake, along with process models to assist management with identifying and navigating the ecosystem of stakeholders that are decision makers in the use of pre-concentration technologies.

Nov 10, 2020

By A Penney, M J. Pascoe, R M. Stephenson

The empirical McCracken and Stacey stability and risk assessment method has been in use for more than 20 years to assess geotechnical stability issues for raise bored shafts. The methodology has been applied with various levels of success. Increasingly, trends in mining and civil tunnelling have been towards larger diameter, single pass, raise bored shafts to rapidly provide means of ventilation, material movement (ore passes), or emergency egress. Identifying and assessing potentially problematic zones before raise boring commences can allow for appropriate risk-based decisions on construction, or to investigate alternative solutions. The implementation of a proactive solution to raising through an identified weak zone is preferred to the application of an engineered solution to an area subjected to substantial instability or failure. Methods for investigating potentially problematic areas are discussed in this paper based on AMC’s benchmarking data. Proactive investigation programmes resulting from these investigations are also discussed. Previous publications discussing the benchmarking data have concentrated on Australian case studies. Increased efforts and recent updates have been made to expand the database to include international case studies. This has provided further refinement of lower bound ‘raise bore rock quality index’ (QR) values, and various rock mass parameters for stability assessments. CITATION:Penney, A, Stephenson, R M and Pascoe, M J, 2018. Raise bore stability and risk assessment empirical database update, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 434–445 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Kanau JL, Kilgour I

This paper describes the metallurgical processes at the 80 000tpd Ok Tedi Mining Limited concentrator, which treats copper- gold ore by single-stage crushing, SAG and ball milling and flotation to produce over 500 000tpa of concentrate. Plant and process developments, including installation of column cells, reduction of fluorine in concentrate, use of sulphidisation and process control improve- ments are also discussed.

Jan 1, 1991

By E Jamieson

For a number of years, Alcoa World Alumina Australia (Alcoa) has been investigating opportunities to produce economically viable products from bauxite residues. Three of these potential products are described here, being Red Sand, ALKALOAM« and REDLIMETM.Red Sand has a nominal particle size of +100 micron and is physically little different to crushed bauxite from which it is derived. In AlcoaÆs Western Australian refineries, Red Sand constitutes up to half of the residue going to impoundment areas. Initial testing indicates that this sand could be processed to provide an acceptable general landfill material, a construction back fill or a material suitable for road base construction. ALKALOAM« is the fine-grained residue often referred to as red mud. A great deal of work has been done to show the benefits of adding this material to sandy soils, which are common in coastal regions of WA. ALKALOAM« has properties that can elevate the pH of the acidic soils and also retain phosphorous, reducing overall fertiliser use and protecting sensitive waterways. REDLIMETM is a by-product of the refining process. This material has a high acid neutralising value. REDLIMETM could be more effective at pH control than most available products because of the fine particle size and sodium carbonate that remains with the product.

Jan 1, 2004

By Neill T. J, Howarth D. F, Malcolm J. McPhersqn

For many years Isa Mine has seen the need for a continuous mining machine which will economically cut hard rock. Tunnel borers are unsuitable due to the size and inflexibility of the machine and the shape of excavation mined. The design of roadheader type machines will not permit the use of the necessary cutting technology. in 1983 a joint project was undertaken by The Robbins Company and Mount Isa Mines Limited to develop and to trial a machine suitable for cutting hard rock in an operating mine. The project was based on the proven technology of raiseboring applied to horizontal development. The Mobile Miner was fabricated and trialled in a disused quarry in the U.S.A. during early 1984. Following these trials, the machine was transported to Mount Isa and commenced mining in September that year. The initial duty was to continue the development of a decline commenced by conventional mining for a conveyor system to serve the deeper southern areas of the 1100 copper orebody. This system will permit direct tipping of copper ore to a new crusher complex and conveying of the - crushed ore approximately 2 kilometres to the central hoisting shaft facilities. The Robbins Mobile Miner MM120-3001 uses a vertical rotating cutting wheel mounted on a horizontal swinging boom to excavate a nominally rectangular shaped heading. The cuttings are collected on an apron and conveyed back through the machine. The resulting excavation is smooth-walled with no blasting damage to the surrounding rock. This provides a safer working environment than does conventional drill and blast development mining. Ground support requirements are considerably reduced.

Jan 1, 1986

By S O. Hille

Modern remote mining operations in Australia are more commonly trending towards fly-in/fly-out (FIFO) sites. This trend is driven by numerous factors including increased business centralisation, reduction in operating costs, and a desire to live in coastal cities that offer closer family networks and a greater diversity of facilities. Consequently, the resource development industry has had to adapt. When WMCÆs Mount Keith Nickel Operation commenced operations in 1994, it was developed as FIFO for its entire workforce. Since then, there have been several permutations of rosters within a 21 day compressed work cycle including the 14/7 cycle. This paper discusses a case study of the change in management process to the 9/5 work cycle focusing on minimising fatigue in the workplace. It includes the discussion of the business case, employee reaction and the practical application. The impact of the best practice change after 18 months is discussed.

Jan 1, 2002

Barrick Gold Granny Smith Mine is currently undergoing conversion from an open cut operation to an underground mine at the Wallaby deposit. The underground project commenced in 2005 with the development of the reserves immediately below the pit and is now currently entering a production ramp-up phase for mining of these two initial surfaces below the pit. With increasing gold prices the owner has been forced to re-evaluate the underground project and has decided to investigate the potential of a deep level mine. This deep level underground mine presents a collection of challenges with the most notable being exploitation of a series of well separated near horizontal lodes ranging in thickness from less than 1 to 20 m. A variety of room and pillar mining methods are employed for extraction with careful consideration to resource recovery and pillar design for long-term stability. Compounding these deep level challenges is a need to accelerate mine level development to maintain the production profile of the mine. This paper describes the challenges, key learnings and outcomes of the studies undertaken to date associated with this project.

Jan 1, 2008

By M J. Thurley, L Lindqvist, D Degerfeldt, J Nyström, R Nordenskjöld

Rock breakage is a major component of all mining and mineral processing operations with the particle size distribution linked to productivity through the comminution chain. Optimisation and automatic control of comminution, material handling, and agglomeration processes is a complex task with large potential for gains in productivity, and energy efficiency. A key factor in realising these gains is the requirement for fully-automated online particle size distribution measurement to provide the necessary feedback and input for control. Moreover, to enable automatic control system it is necessary to provide a consistent, reliable size distribution measurement that avoids the significant errors resulting from under-sizing overlapped particles and over-sizing clusters of fine particles. Published literature and observation of commercial systems indicate a body of predominantly 2D photographic based particle size measurement systems that suffer from a number of significant errors except in the simplest case of a monolayer of particles under good illumination with limited colour variation in the material. In order to overcome these limitations a university and industry collaboration developed three-dimensional particle measurement (3DPM) between 2006 and 2012, based on 3D surface profile measurement of the visible material on conveyor. 3DPM avoids particle delineation errors due to variation in material colour and shadows, detects overlapping versus non-overlapping particles, and identifies areas of fine particles as fines and not large rocks. 3DPM measures: the visible material and calculates its particle size distribution, bulk volume, detects boulders, and conveyor belt fill factor in an automated consistent manner. Furthermore, 3DPM’s advanced algorithms allow observation of particle variation that would otherwise be undetected without the capacity to identify visible areas-of-fines and overlapped particles. Boliden Mines has installed 3DPM at three operations for measurement between the stockpile silo and grinding mill, and measurement after the primary crusher. Fragmentation measurements across multiple years of measurement are presented with some observations of plant behaviour. In the future 3DPM results will be incorporated into automatic control strategies for plant optimisation. 3DPM is used across a wide range of material types and applications that also includes; limestone aggregate for quality control in manufacturing, agglomerates for closed-loop automatic control in chemical production, and measurement of coke for size-based blending feed control to the blast furnace in steel production. CITATION:Thurley, M J, Degerfeldt, D, Nyström, J, Nordenskjöld, R and Lindqvist, L, 2018. Automated, online measurement of bulk material size distribution on conveyor using 3D profile imaging at Boliden Mines, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 641–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018