Search Documents

Vertical flow systems (SAPS, vertical flow wetlands) are increasingly used for passive treatment of mine drainage that is net acid. Data on 30 systems in eastern US show that well designed systems typically add about 40 g/d/m2 of alkalinity to influent net acid water. If they are designed with a conservative loading rate of 25 g/d/m2 and carefully constructed, they produce net alkaline water. Alkalinity added depends on influent acidity, Fe, pH, and retention time, and ranges widely, from 7 to 484 mg/L, so this is not a useful design criterion. Some waters may benefit from retention times longer than the conventional 12 - 16 hours, but the design must be partly based on cost-benefit considerations. Systems with fine limestone added to the compost layer perform better than average, perhaps to an alkalinity generation rate of 80 g/m2/d. A variety of problems are noted in the 30 systems and others reported in the literature. Systems with high influent Fe (> ~75 mg/L, varying with pH) tend to gradually decrease in flow rate because of precipitation and settling of Fe hydroxides on top of the compost layer. Some high-Fe systems precipitate Fe in the limestone layer, suggesting inadequate compost thickness, or short-circuiting through thin spots. Systems with Al exceeding about 10 mg/L tend to plug because of Al hydroxide precipitation in the limestone layer. Flushing only removes a small part of this precipitate, but can extend life. Some systems are ineffective because of failure of the inflow system. Some systems are uneconomic because they are oversized. A continuing program of inspection and maintenance is necessary for long-term performance.

Jan 1, 2003

Efficiency, Economics, Energy and Emissions - Emerging Criteria for Comminution Circuit Decision Making

Sep 13, 2010

By Munro P. D

Eh-pH measurements were taken on an industrial zinc reverse flotation process at Brunswick Mining and Smelting Corporation Limited. Laboratory zinc reverse flotation testwork on samples of the feed to the industrial process produced Eh-pH data which were similar to the data from the industrial process.Later, the Eh-pH data from the industrial process were compared with data from a pilot plant scale zinc reverse flotation process at Mount Isa Mines Limited. After comparison with the data from Brunswick Mining and Smelting Corporation, deficiencies in the pilot plant Eh-pH data could be recognised and corrective actions were taken for the pilot plant. A robust pilot plant zinc reverse flotation process was obtained with consistent performance at the expected level.The implications of these findings for a range of processes are also discussed.

Jan 1, 1988

Contractors are used extensively in the development of underground mines in Australia. Often problems arise, some originating as far back as the feasibility stage of projects, through inexperience, lack of preparation and inflexibility by both parties.Guidelines are put forward for both principals and contractors which are seen as necessary to ensure that disputation is avoided and the full benefits of the use of contractors are obtained.

Jan 1, 1985

By Rashkovski GB

Until recently amalgamation has been the main process forextracting large gold particles from gravity concentrates obtainedduring the dressing of ores and placer gold deposits.Development of new technology for treating the gravityconcentrates was necessary because of the harmful effect ofmercury on subsequent production processes and theenvironment. The harmful effect of mercury is particularlyevident in the resin-in-pulp process that is widely applied inRussia.

Jan 1, 1993

THIS instrument, depends on the principle that, over a short period, the surfaee of a porous substance from which a liquid is evaporating receives the same amount of heat by conduction, convection, and radiation as it loses in the latent heat of the evaporating liquid. If, then, the amount of heat being received by a surface can be measured, the rate of evaporation can also be obtained. The Kata thermometer is also based on this principle differently applied.The instrument, as shown in Fig. 1, consists essentially of a thermometer with a sliding which is divided by three pointers into two equal parts which may be spaced so as to cover a distance of, for example, 5° of the thermometer scale. The instrument is calibrated so that the amount of heat required per unit area of the bulb to raise the menissus is known. The method of using the instrument is as follows:The slide is first set so that thc central pointer is at the temperature of the evaporating surface.The thermometer is cooled by any convenient means so that the meniscus is several below the lowest pointer. The thermometer is then placed near the evaporating surface, when the Ineniscus begins to rise and the time taken for it to rise from the lowest to the top pointer is measured. From this and the calibration results the amount of heat retained per unit area of the bulb at the mean temperature...

Jan 1, 1928

By J Koppe, J F. Costa

A fundamental error of sampling occurs when a sample is extracted from a larger mass of ore or lot. The act of sampling requires that all particles belonging to the lot have an equal chance of being extracted. This type of sampling is called unbiased sampling. The sampling equipment (herein referred to as the sampler) should be constructed with some additional mechanical characteristics to guarantee that the samples will be unbiased. Samplers, extracting increments from a continuous flow, such as a conveyor belt, collect aliquots at regular time intervals. These time intervals relate to the number of aliquots extracted from a given mass of lot, whilst passing through the continuous flow. The frequency of extractions will influence the precision or the error of the sample (integration error). Further, the ore variability influences the amount collected from the continuous flow. Normally, the sampling protocol utilised is designed for the extractions obtained from the conveyor belt, omitting any error committed during this operation, ie the error of extracting from the continuous flow. This study aims to analyse the error of sampling a continuous flow by using a variogram with added on auxiliary functions. Each different piece of material passing through the flow will exhibit a distinct temporal variogram, which should influence the frequency of the samples being extracted for each chosen sampling error. The methodology used is presented in the form of a case study from a coal processing plant.

Jan 1, 2005

An Environmental Impact Statement (EIS) for a major mining development typically has to address various aspects of surface water management, including some which generally tend to be the more contentious: the diversion of rivers and creeks from areas disturbed by mining, and their rehabilitation; the effective management of disturbed area run-off via the collection, containment and treatment of contaminated water on site in sedimentation dams; the collection, containment and treatment of mine pit water; the decommissioning of surface water storages; final void water quality; and water discharge criteria. Environmental Impact Assessment processes for proposed mining developments in Australia at the state and commonwealth level usually involve a form of Initial Advice Statement (or Notice of Intent), Terms of Reference, an EIS, and a Supplementary Report (or similar) which responds to agency and public comment on the EIS. The EIS is used by approval agencies to decide the acceptability of the Project, and to set the conditions of approval. The conditions are often in the form of a state-issued æOperational LicenceÆ or similar. With mining, the initial approval at the EIS stage is often just a pre-cursor to various other planning related approvals, including obtaining a mining lease. Afterwards, mine plans and plans of operations must be submitted to government at various stages of the mineÆs life, ostensibly to provide the detailed mine planning over periods of one û five years. Despite all this additional planning and documentation beyond the submission of the EIS, government approval agencies are increasingly not satisfied with conceptual water management designs and commitments to an outcome (such as meeting a specified water quality standard) in the EIS. Agencies are also requiring sufficient water management design information to be convinced that the outcomes are achievable. To assist proponents of major mining developments, the Queensland Government has published Technical Guidelines for water management, and Environment Australia has published a æBest Practice Environmental Management in MiningÆ booklet on water management. In addition, the Australian and New Zealand Environment and Conservation Council (ANZECC. 2000) has published Water Quality Guidelines which provide an approach to water management, and provide receiving water investigation trigger criteria. So, what are the water management issues that are likely to be the subject of comment, debate and negotiation prior to the EIS being approved? and what commitments may a mining proponent have to make in order to convince the approval agencies that sufficient investigation and design has been provided? This paper provides some answers to this question, by reference to recent major mining proposals which the author has managed through state and commonwealth Environmental Impact Assessment processes.

Jan 1, 2003

Innovative and Resource-Preserving Washing Processes for Primary and Secondary Raw Materials

Sep 13, 2010

Two continuous computer controlled, remote air analysis (RAA) systems operate at The Zinc Corporation, Limited (ZC) to give early warning in case of an underground fire at ZC or New Broken Hill Consolidated Limited (NBHC) mines. Air drawn from underground sampling points via a tube bundle system is analysed for carbon monoxide and carbon dioxide. An alarm is sounded if the concentrations of these gases exceed bench mark figures.

Jan 1, 1983

Iron from the blast furnace constitutes the starting point in steel production and any increase that can be made in iron production will bring about important repercussions in a long line of processes. Coke constitutes a major item in furnace operation and consumption at the Port Kembla Works of Australian Iron & Steel Ltd. has been approximately 1,850 lb. per ton of iron produced on ore practice, or 3,000 tons per day.For many years coke quality has been subject to much criticism by furnace operators throughout the world, sometimes with little real grounds. Whatever the merits of previous arguments, and they were no doubt two-sided, the development of bigger furnaces has focused attention on coke strength. At the same time a decrease in the quantity of good quality coking coals available to many plants has stimulated research in this field.Extensive coke research has been carried out overseas, and in Australia the.B.H.P. Organization is now actively doing likewise in its Central Research Laboratories at Shortland near Newcastle, N.S.W., and works research groups at Newcastle and Port Kembla Steelworks. Similar work has been initiated in the beehive coking industry. Such work is in its infancy and this paper will outline the direction of the activities at Port Kembla rather than propound specific solutions.At Port Kembla good quality coking coals are readily available from the IIIawarra coalfield. The seams generally mined for coking are Bulli and Wongawilli and to a much smaller extent Tongarra. Characteristics of these coals appear in Table 1.

Jan 1, 1958

By A Lu, C Wang

The natural semiconducting mineral rutile and sphalerite exhibited highly photocatalytic activities on degradation of methyl orange under visible light irradiation. The isomorphous substitutions of host metal ions by foreign ions and other defect states in natural semiconductors altered the band structure, decreased the intrinsic band gap, and then made them very attractive for solar energy utilisation. Our study indicated that natural semiconductor minerals might be suggested as a new class of cost-effective and solar light-responsive photocatalyst.

Jan 1, 2008

By D M. Marques, J F. C L Costa

The estimation of process plant head grade is not trivial and is a source of constant dispute within the mining industry. Grade estimates informed by the short term mine planning are frequently not reproduced by sampling the continuous flow of ore at the plant. Head grades are normally obtained by periodically sampling the continuous flow during a day or shift, and taking the average of the multiple increments collected. The standard error of this mean grade depends on the ore variability and the frequency (number) of aliquots extracted. The more increments are taken the higher is the precision on the calculated mean. Variographic experiments are normally used to map grade variability along a certain period of time and the extension variance is derived from this variogram. This experiment is time consuming, expensive and cumbersome. Mining industry personnel rarely apply this approach. Additionally, a temporal variogram can vary from day to day as different ores are mined along the life of the mine. This paper investigates a novel approach based on simulating the grades feeding the processing plant. In situ 3D grade models are built using geostatistical simulations. Grade spatial continuity and variability are reproduced in models that mimic the real deposit. These models are used in mine planning and scheduling transforming a 3D block model into an one dimensional string of values feeding the plant (one dimension flow). These grades have the statistical characteristics of the unknown real grades and can be sampled to emulate a variographic experiment. The results showed consistency and adequacy to estimate the sampling error (Gy, 1998 p 31) for various sampling intervals using the simulated grades. Also the results show a variographic experiment can change significantly from time to time, as ore changes and a selected sampling protocol can become obsolete if not adjusted for ore variability.CITATION:Costa, J F C L and Marques, D M, 2012. Defining a sampling strategy for a continuous flow supported by geostatistical simulations, in Proceedings Sampling 2012 , pp 3-8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

Characteristics Analysis of a Bastnaesite Rare Earth Mineral for Recovery of Cerium

Sep 13, 2010

The Australian Mineral Industry has to compete on world markets, so its mineral research has to be aware of overseas developments, it must be of world class, and it must utilise as many ideas as possible in order to solve those problems that uniquely affect Australian minerals processing. North American mineral and resource research may be taken as a guide to world government, industrial, contract, and entrepreneurial research trends and ideas. A number of interesting findings are noted that may guide Australian developments and strategies for the future, in minerals research and exploitation.

Jan 1, 1986

By Davies C. E

At present the source of virgin iron for steel produced in New Zealand is titanomagne- tite extracted from titaniferous beachsands. Some of these beachsand deposits contain extractable quantities of ilmenite as well as titanomagnetite and both minerals represent challenging sources of vanadium and titanium products in addition to iron. This study looks at some theoretical aspects of smelting these ores directly with coal rather than with electric power, and takes into consideration the properties of the raw materials, the thermodynamics of possible process routes and the background of the economics involved.

Jan 1, 1980

Excessive use of computers in teaching, especially in self-learning programs, may destroy creativity and initiative. It is essential that engineers remain innovative to develop new technology. Safety legislation may have hindered the Development of mine managers. It may be necessary to develop two distinct streams of mining engineers. One should be biased towards human relations and safety, to 'be a certificated mine manager, and the other should be mathematically based as a high-technology mining engineer who would not necessarily qualify for a certificate of competency without a postgraduate course.

Jan 1, 1986

By Jeffery RI, Pollard CA, Fear NJ

The paper describes the detailed hydrogeological studies carried out prior to the sinking of twin shafts at British Coal's new mine at Asfordby, Leicestershire, UK. The test methods for assessing potential groundwater inflows to the shafts are discussed and details are given of the ground freezing scheme employed through the major aquifer zone in the Sherwood Sandstone at a depth of 375 metres. During shaft sinking pressure recovery tests were carried out to further assess potential inflows and the results are compared with those from the surface tests prior to sinking.

Jan 1, 1988

By Kubo H, Kubita K, Morinara M

A quantitative method for predicting the mechanical properties of zinc alloys is proposed on the basis of the molecular orbital calculation of electronic structures. A new parameter which is the s-orbital energy level, Mk , of alloying elements in zinc was introduced into this method. This Mk parameter correlates with the electronegativity and the atomic radius of elements. The compositional average of this parameter varied linearly with the tensile strength and the hardness of commercial alloys and some alloys developed by Mitsui. This electronic method was very convenient in designing high performance zinc alloys efficiently.

Jan 1, 1993

Characterisation of Computer Printed Circuit Boards for Hazardous Properties and Beneficiation Studies

Sep 13, 2010