Search Documents

PAPERS : 1 COMPUTER AIDED DESIGN OF MINE WATER MANAGEMENT - Z KESSERU 2 THE HYDROGEOLOGICAL PROBLEMS OF GROUNDWATER PROTECTION IN MINING REGIONS - V A MIRONENKO 3 WATER MANAGEMENT OF THE MAE MOH PROJECT -òò SIRI CHITCHOB 4 WATER MANAGEMENT AND WATER TREATMENT AT GOLDPN CROSS - M P A WILLIAMS

Jan 1, 1988

AustraliaÆs success as a mineral producer and exporter rests heavily on its technological competence. That competence is based not just on adopting internationally-developed technology but also on ground breaking research conducted at Australian research institutions, many of which have global reputations. A number of forces are now operating to speed the introduction of advanced technology to mining and processing operations around the globe and this will create pressure on the Australian industryÆs ability to retain its competitive edge. Examining the foundations of that national research base and the associated culture of innovation may provide some guide to the dynamics that will be required to maintain technical competitiveness in the future.

Jan 1, 2008

By Brown D. N, Troth D. A

Large blast furnaces demand high standards of preparation of feed materials which must meet tight specifications of chemical and physical quality. Measurement of these factors must be expeditious but the nature of the coke, sinter, ores and fluxes and the large tonnages involved requires substantial mechanical sampling plant. The equipment, its operations, and its problems, associated with the 5000 t.p.d. No.5 blast furnace at Australian Iron and Steel Pty. Ltd., Port Kembla, are described and the efficacy of chemical blending achieved in the ore blending yards and sintering operation, is reported.

Jan 1, 1976

Uniaxial compressive strength and Young's modulus values measured in the laboratory on NX diamond drill cores were examined statistically to bring out any significant differences between different locations in the mine which might require special treatment in subsequent photoelastic analyses of the mine layout. Correlations were sought between the strength and modulus and various other features of the rock. The estimated mineral content of the core correlated with the modulus of the core, but the range of modulus values was too limited to show any strong correlation with compressive strength.Strength in the vertical direction was found to be significantly higher than in the horizontal direction and the same pattern was followed by the moduli, but was less pronounced. It was concluded that, whilst the modulus variations were significant, they would not invalidate any photoelastic studies.

Jan 1, 1969

By Adranyl W. W

Sub-level caving with bottom ore drawing has gained wide acceptance in rich, soft, low magnetic iron ores because it provides moderate ore dilution and ore losses. The main problem here is the high rock pressure exerted on sub-level drives situated in the sub-level sill pillars. To reduce this effect, the ore block is divided into panels. This paper illustraes the method of determining the maximum panel width providing low maintenance cost of sub-level drives.

Jan 1, 1995

By P Lilly

Blasting is the primary comminution process in most mining operations. This process involves the highly complex and dynamic interaction between two main components. The first is the detonating explosive and the second is the rock mass into which the explosive is loaded. The mechanical properties of the rock material (such as dynamic strength, tensile strength, dynamic modulus and fracture toughness) are important considerations in understanding the blasting process. However, it is the characteristics of the geological defects (joints, foliation planes, bedding planes) within the rock mass that ultimately determine how effectively a blast performs in terms of fragmentation, all else being equal. The defect characteristics include, but are not limited to, their orientation, spacing, and mechanical properties. During the blasting process, some of the geotechnical characteristics of the rock mass are substantially changed. From the blasting outcome point of view, the most notable and important is the change in fragment size distribution that the rock mass undergoes. The pre-blast in situ defect-bounded block size distribution is transformed into the post-blast muckpile fragment size distribution. Consequently, it is fundamental to our understanding of and ability to predict the blasting process that both the blastability of a rock mass and its transformation into the fragment size distribution can be appropriately quantified.

Jan 1, 2001

By Arit I, Adisoma G

General Limit Equilibrium Method (GLE) and Janbu's Generalised Procedure of Slices (GPS) are two limit equilibrium methods in slope stability analysis which satisfy all equilibrium conditions. Numerical difficulties associated with these metho

Jan 1, 1998

By Walton S, Wheeler D. J, Sargent D. M, Ting L. Y

Goonyella-Riverside mine is an open cut coal mine in Central Queensland. One component of the mining operations at this site is an uncompacted spoil dump some 50 m above the natural ground surface and over 300 ha in extent formed as a result of bucket wheel excavator operations. Plateau area slopes are 0.5¦ to 1.5¦ with irregular outer dump slopes of 9.5¦ - 17¦Investigation was undertaken and a series of trials planned to assess the suitability of a variety of stabilisation proposals to meet the client's requirements and to conform with Department of Resource Industrystabilisation guidelines.

Jan 1, 1992

The Malvern Hills coal project is now in an advanced stage of development with the stripping of overburden from above former underground workings in which a 3 m seam of subbituminous C coal with very low ash and sulphur was previously mined. The main seam dips at 45¦ to the south-east, along with other adjacent potentially recoverable thinner seams, and the strike extent of past coal mining in the Malvern Hills approaches 10 km with most extraction by underground methods. Overburden and interburden is predominantly weak mudstone, with only very minor sandstone, whilst a 1 - 2 m thick veneer of Last Glaciation loess covers the area. The coal product from the present mine site will supply the local industrial market, with production planned to peak at about 20 000 tpa. Settling pond design has been based on several different approaches, including an estimate of likely inflows from the contributing catchment of about 5 ha under predicted storms having a ten year recurrence interval. A pond of about 1000 m2 in area has been constructed with its invert in mudstone bedrock, and soil slopes have been lined with lime-stabilised clayey loess silt incorporating a gravel armour layer. The pond outflow takes place via a 2 m high 1.8 m diameter concrete dewatering tower, with a skimmer arrangement to lower the pond by approximately 500 mm between storm events. The overflow water discharges to the main stream above a natural wetland, which will act as a secondary polishing pond, and this is to be enhanced in conjunction with the neighbouring forestry company. Discharge consents specify turbidity and pH as the controlling criteria, and both will be monitored at the settling pond discharge point as well as at the entry to the main stream. Investigations to date indicate that the pH of water exiting from previous underground workings is in the range 6.8 to 7.2, and that acidic drainage will not be an issue with this mine site. No dispersive clays have been identified in assessing the overburden and batter materials, although erosion during storm events is expected and all drains will ultimately be routed through the main settling pond to ensure adequate control of runoff-generated sediment. Reestablishment of vegetation on cut and fill batters remains a priority, and ongoing monitoring will ensure satisfactory long-term performance of the pond system.

Jan 1, 2003

By Brechtel C. E

Providing adequate airflow to effectively dilute and remove diesel pollutants in large mine working headings is a little researched area. A simulated diesel mucking operation was carried out in the Exxon Colony Pilot Mine in Colorado to establish expected levels of diesel pollutants in dead-ended working headings. This heading was nominally 15.3 m (50-ft) wide by 9.2 m (30-ft) high. Two face ventilation systems were tested using sulfur hexafluoride tracer gas to represent the diesel pollutants. The results of these tests showed that conventional face ventilation systems operating at high flow rates could adequately ventilate diesel equipment in the 447-522 kW (600-700 hp) range, even in a dead heading 91.4 m (300 ft) in length.

Jan 1, 1988

Hamersley Iron Pty. Limited has maintained an interest in the screening of iron ore fines (nominally -6 mm). However, no dry screening process had successfully demonstrated acceptable separating efficiencies at high tonnage rates, low operating costs, and mechanical reliability when screening iron ore fines (containing up to 6% free moisture) at sizes of around 1 to 2 mm. A new type of vibrating inclined screen has recently been developed which is claimed to have a non-blinding screening surface. It was decided to test a pilot scale unit in an existing pilot plant located at Hamersley's facilities at Dampier, Western Australia. The appropriate operating parameters such as vibration speed and feed rate were determined using one fine ore type. Mats with different aperture sizes, and different feed moisture contents were also tested. Trials were then conducted on various fine ore types to indicate the effect of different size distributions on separating efficiencies. The effects of feed moisture content were determined with these ore types, and a blend of lump (nominally -30+6 mm) and fines was tested to compare the screen's performance with that of the bottom deck of the minesite product Screens.

Jan 1, 1991

By Harbort G. J

Jameson cell pilot plant trials were conducted in a number of areas in the Red Dome gold/copper flotation plant during 1991. The aim of testwork was to reduce the amount of cyanide soluble copper reporting in tailing to the gold leach plant, and hence reduce cyanide consumption. A number of these tests were conducted in parallel with conventional flotation columns. Laboratory tests were conducted to simulate the performance of the existing plant when compared with the addition of the Jameson cell allowing an extra sulphidising phase. This paper reviews the comparison of the Jameson cell and conventional columns in recovering cyanide soluble copper, while maximising copper concentrate grade. Key parameters that are investigated are residence times, air/pulp ratios, superficial gas recoveries and size by size recoveries. A brief comparison of performance of the Jameson cell and column in the controlled potential sulphidisation process is also presented. An estimation of the reduction in cyanide consumption is given.

Jan 1, 1992

By Lunt D

Arsenic is classified chemically as a metalloid. That is, it has properties intermediate between those of metals and non-metals. Like non-metals, it combines with many metals to form arsenides (eg arsenopyrite FeAsS, niccolite NiAs, sperrylite PtAs2), but like metals it forms sulphides and oxides (eg realgar AsS, arsenolite As203). Arsenic is distributed widely in the Earth's crust at an average concentration of 1.5 mg/kg and is present in more than 150 minerals.

Jan 1, 1991

By Higuchi K, Sekimoto Y

In this report,the results of the large diameter drilling tests in coal seams assisted with water jet are described. The stress relief in coal seams by this new method is as effective as by the conventional method and the penetration speed by this method is 1.5 times as fast as by the other method. 1 Introduction The average mining depth of Japanese coal mines has already attained about 700m from the surface. Almost all coal mines are suffered from occurrence of coal and gas outbursts. To prevent outbursts, some countermeasures are taken generally. In particular, large diameter stress relief borings have been carried out quite often at Akabira coal mine located in the northern part of the Ishikari coal field in Hokkaido,JAPAN. These borings have had successful results but the drilling work of such large diameter

Jan 1, 1987

Jarrah Decline is currently the only underground operation at the Boddington Gold Mine, (BGM). The mine is located 120 km SE from Perth in WA, with mineralisation hosted within deeply weathered felsic and intermediate intrusions and volcanic rocks of the Saddleback Greenstone Belt (Morley and McBride,1995). Open cut operations commenced in April 1987 with a mill throughout of 3.OMtpa. A number of upgrades have since taken place, with the oxide material throughput currently milled at a rate of 7Mtpa. In 1992 a separate circuit, the supergene mill, was commissioned to treat copper material from the open cut and now ore from the Jarrah Decline. Current throughput in the supergene plant is 30,000 tonne per month, with a varied blend according to mill requirements. Total gold production from the Jarrah Decline in 1994 was 60,000 ounces from 90,000 tonne of ore.

Jan 1, 1990

About 3km2 of the central Luise Caldera, in which the Lihir orebody is located, is geothermally active wit.lj gas seeps and fumaroles, and in some areas, a water table at boiling point.The proposed mine, adjacent to Luise Harbor, will be excavated to more than 200m below sea level and will extend into the geothermal system to depths at which current rock temperatures are 170¦C.

Jan 1, 1994

Mining is taking place at increasing depths of cover on the Southern Coalfield beneath pre- dominantly massive sandstone strata. Within the next twenty years, there will be longwall mining at depths greater than 600 m. As the Sydney Metropolitan area continues to expand and as coal mining approaches these urban areas subsidence will continue to become an increas- ingly important aspect of coal mining research. Investigations commenced in the mid 1960's and it is now possible to predict subsidence in the Southern Coalfield with reasonable con- fidence. The work is showing that the characteristics of the subsidence troughs over the deeper mining at Appin differ from the characteristics of mine subsidence at less cover. The longwall mining at Appin Colliery has resulted in a maximum measured subsidence of 730 mm. The maximum strains were small because of the large radii of curvature of the subsidence profiles. There was no damage to any of the buildings in the township of Appin.

Jan 1, 1981

By R A. Pax

Operational grinding mills emit significant acoustic emissions which are a consequence of the dynamic environment prevailing inside them. From a technical perspective, the noise presents an opportunity to determine some details of the processes occurring inside the mills. The noise generated is not random and can be attributed to a range of events that occur inside these mills, consequently non-contact acoustic determinations of in-mill behaviour provide powerful insights into the operation of primary comminution tumbling mills. To enable a logically coherent picture to be formed of the processes inside a mill, arrays of microphones have been used. This approach allows a clearer picture of the in-mill behaviour of the charge to be accessed. In contrast to single microphone approaches, usually located near the expected charge toe position, an array of microphones allows much more useful information to be obtained from grinding mill noise.This paper will discuss and present data obtained from microphone arrays positioned at the toe and shoulder locations of a mill, and how this information can then be used for the optimisation of grinding mills in real-time.CITATION:Pax, R A, 2012. Determining mill operational efficiencies using non-contact acoustic emissions from microphone arrays, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 119-126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By H Lieberwirth, M Pfeifer, F Heinicke

HPGRs (high pressure grinding rolls) have been developed within the last decades for energy efficient processing of a wide variety of ores. Special interest has been raised by projects increasing the capacities of processing plants by installing HPGRs prior to ball mills. Bond ball mill tests have been used for decades as a base for ball mill dimensioning in mineral circuits. For final CAPEXOPEX considerations of the processing circuit, one key question is about the level of grinding energy split between HPGR and downstream grinding stages. This is especially interesting if the downstream process comprises multiple grinding stages combined with separation steps. The paper presents investigations on grinding energy consumption, size distribution and microfracturing of HPGR products, which affect the efficiency of the whole comminution and sorting process.

Aug 24, 2022

The Main Seam occurs in two 'pods', termed North and South, separated by an east-west oriented 'want' zone (most probably a palaeo-channel). The seam on either side of the 'want' area reaches thicknesses of over 30 metres but the North Main Seam adjacent to the 'want' zone has been split into multiple seams of 10 to 15 m thickness. Rock types in the inter-burden of this area are characterised by inter-bedded sandstones and carbonaceous mudstones varying in thickness from 0.5 to 5 m. In the South Main Seam, an area of un-split coal exists and is characterised by few inorganic partings. Overburden in this area varies geographically from relatively thick mudstones in the south and east part of the coal deposit to inter-bedded sandstones and carbonaceous mudstones adjacent to the 'want' area. The sandstone/mudstone overburden probably represents a splay or splay-channel complex emanating from the larger 'want' area palaeo-channel. Modelling lithological variability is of use because it is one of the factors used in predicting cavability and roof support system design. The coal in both the north and south deposits were found to exhibit highly predictable quality and breakage parameters in relation to the coal geometry. Although ash yield and sulphur are mostly low and not variable, volatile matter and thus fixed carbon, varied in relation to seam thickness. In general, volatile matter (dat) decreased and moisture increased with decreasing seam thickness whereas moisture increased with decreasing seam thickness. In addition to these parameters it was found that the energy needed to crush the coal was lowest at the top and bottom of the seam and, on a whole seam basis, decreased with seam thickness. All of these parameters were found to vary in relation to the vitrain band content of the coal which itself was controlled by seam geometry. These parameters can therefore be modelled and inputted into mining plans and quality control operations.

Jan 1, 1996