Search Documents

By E J. B van Etten

This paper reports on the results of several years of monitoring rehabilitation at a silica sand mine on the Swan Coastal Plain, south of Perth. Mining here occurs below the regional watertable and leaves a post-mine landscape of dredge pond voids (pit lakes) with surrounding battered slopes. The restoration we recommended was to develop the pit lakes as wetlands of regional analogue and value. Several different restoration techniques have been applied to re-vegetate pit lake slopes over many years which have enabled an evaluation of reasons for success/failure of different restoration approaches. Learning acquired clearly showed the benefits of using fresh topsoil for restoration over topsoil that has been stockpiled for several years. Most topsoil used in restoration was from seasonal wetlands and consequently restoration was most successful in the riparian zone from the edge of pit lakes to about 2 m vertically above the water table. Topsoil restored areas above this level remained poor in plant species and cover. Conversely, remedial seeding/planting proved largely unsuccessful. Permanently and seasonally flooded pit lake margins recolonised relatively quickly and successfully with native sedges and rushes. Development of rehabilitated upper slope plant communities over time was evident with loss of typical wetland species and greater growth and survivorship of upland and dampland plant species on mid to upper rehabilitated slopes. Plant communities of lower slopes showed a converse pattern of development, with a shift towards a more typical wetland composition. We believe matching topsoil to site and development of topographic profiles similar to natural wetlands of the region are the keys to optimising restoration success of sand mines with shallow water tables.

Oct 5, 2011

By Daniels E. J, Morgan W. A

In response to the increase in consumption of galvanised steel for automobiles in the last decade and the problems associated with remelting larger quantities of galvanised steel scrap, a process is being developed to separate and recover the steel and zinc from galvanised ferrous scrap. The zinc is dissolved from the scrap in hot caustic using anodic assistance and is recovered electrolytically as dendritic powder. The dezinced ferrous scrap is rinsed and used directly. The process is effective for zinc, lead, and aluminum removal on loose and baled scrap and on all types of galvanised steel. The process has been pilot tested for batch treatment of 900 tonnes of mostly baled scrap. A pilot plant to treat continuously loose scrap, with a design capacity of 48 000 tonnes annually, has been in operation in East Chicago, Indiana since early in 1993. The first 450 t of scrap degalvanised in the pilot plant have residual zinc below 0.01 per cent and sodium dragout below 0.01 per cent. Use of degalvanised steel scrap decreases raw materials, environmental compliance costs, and opportunity costs to steel- and iron-makers. Availability of clean degalvanised scrap may enable integrated steel producers to recycle furnace dusts to the sinter plant and EAF shops to produce flat products without the use of high quality scrap alternatives such as DRI, pig iron, or iron carbide. Recycling the components of galvanised steel scrap saves primary energy, decreases zinc imports, and adds value to the scrap. The quantities of zinc available by the year 2000 from prompt and obsolete automotive scrap will approach 25 per cent of zinc consumed in the major automotive production centres of the world. Zinc recycling from galvanised steel scrap, either before or after scrap melting, will have to be Implemented.

Jan 1, 1993

By Willis GM

The matte-metal-equilibria in the system Pb-Cu-S have been studied at temperatures between 720 and 920¦C by direct sampling and D.T.A. methods. These results are compared with those of other workers. The applications of such data to a continuous copper drossing process, and to a number of other metallurgical processes are discussed.

Jan 1, 1975

By P Tobar

The development plan (long-term plan) of El Teniente Mine, Codelco-Chile, includes 100 per cent primary ore, located at increasing depths, which may involve several difficulties related to the application of the current panel caving method, such as a high seismicity level, a coarse fragmentation and ore pass damage. Therefore, it is a strategic priority for the El Teniente mine, to design and to test alternative mining methods, at similar or lower costs to ensure an efficient and safe ore extraction. In this context, the Macrotrench method is developed, as a competitive alternative to the current method. The document describes the panel caving method, the experience achieved in the primary ore exploitation from the geomechanical point of view. It also describes the æmacrotrenchÆ method as an alternative to the current exploitation method. Finally, the comparative advantages of macrotrench in relation to panel caving are presented. The results obtained during the engineering stage include the following aspects:the mining design, the material handling, a geomechanical evaluation of the method, and a comparative analysis.

Jan 1, 2000

By T P. Medhurst

In many cases mine design is the most important driver of the profitability of a mining project, however to reach an æoptimumÆ mine plan many compromises have to be made. Some of the fundamental profit (and loss) drivers relate to stoping methods and stope design parameters. Inevitably trade-offs have to be made between the stability of underground openings, ground support costs and production efficiency. This paper looks at the role of geomechanics in the mine planning and design process. The concepts of æcontrollable lossesÆ and æuncontrollable lossesÆ are developed as a means of partitioning ground control costs. A stope design example is given which provides a method of examining mining costs, and includes a decision making element in order to quantify geotechnical impacts and select stope dimensions. The method also provides a general framework as a means of balancing ground control costs against maximising returns from an underground mining project.

Jan 1, 2000

By J R. Manuel, J M. F Clout

The importance of goethite to Australian iron ore production is steadily increasing as the proportion of goethite-rich, martite-goethite bedded and channel iron deposits increases at the expense of declining production from high-grade microplaty hematite deposits. For this reason, an improved understanding of goethite in iron deposits, its genesis, goethite types and their physical and metallurgical properties is vital to maintaining optimum sintering and blast furnace performance in Asian steel mills.The terminology used to describe goethite in Australian iron deposits is currently highly variable. The discredited mineral name ‘limonite’ is still in widespread use as a field term for goethite and there are many misconceptions concerning goethite chemical grade and downstream physical and metallurgical properties. The goethite classification proposed here is based on geological and physical properties from which three types are recognised including brown goethite, dark brown-black vitreous goethite and highly microporous, friable yellow ochreous goethite.In practice, typical vitreous goethite with highly reflective surfaces and conchoidal fracturing, characteristic of the hard cap zone appears from X-ray fluorescence (XRF) and electron microprobe analysis to be significantly higher in Si (up to 18.7 wt per cent), Al (up to 3.5 wt per cent) and S (up to 0.14 wt per cent) compared to the generally very low (<1 wt per cent for Si and Al) levels of these elements in ochreous goethite and brown goethite. The data dispels the common misconception that friable earthy or yellow ochreous goethite is high in Al and Si and other chemical impurities. However, P was found to be consistently higher (mean of 0.112 wt per cent and up to 0.296 wt per cent) in ochreous goethite than brown goethite (mean of 0.011 wt per cent) or vitreous goethite (mean of 0.031 wt per cent). The highly porous microstructure of ochreous goethite is thought to have a much higher surface area, which may aid in preferential adsorption of P onto the ochreous goethite mineral surface.CITATION:Manuel, J R and Clout, J M F, 2017. Goethite classification, distribution and properties with reference to Australian iron deposits, in Proceedings Iron Ore 2017, pp 567–574 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Bureau of Medical Inspection, Broken Hill, New South Wales.INTRODUCTIONFor a considerable time it has be3n realised that the pathological changes produced in human lungs by the inhalation of free silica varied, not only according to the amount of silica inhaled, its particle size and the period during which it was inhaled, but also according to other mineral elements which might be admixed with the fine silica dust and inhaled along with it, or inhaled subsequently to the silica containing dust. It was observed that, in many instances, these admixed dusts tended to inhibit the action of the free silica in causing injury to the lungs, as well as the development of certain complications, whilst in other cases it was felt that certain substances could actually accelerate the tissue damage caused by the silica.A fresh impetus to the problem of the prevention of the development of silicosis was given when, in 1937 and 1939, Denny, Robson and Irwin published papers entitled "The Prevention of Silicosis by Metallic Aluminum." Working at the same time at the Saranac La.boratory, and quite independently, and using a colloidal aluminum hydroxide, Gardner arrived at the same conclusions as Denny, Robson and Irwin, namely, that in experimental animals the development of silicotic changes could be prevented if eithertogether with the silica, or subsequent to its inhalation...

Jan 1, 1946

Thiess Dampier Mitsui's Moura-Mine is located in the south-eastern corner of Queensland's Bowen Basin, some 180 kms west of Gladstone. Current requirements of the open cut operation are to drill and blast 25 million cubic metres of overburden per year, consuming some 12,000 tonnes of explosive in order to meet the requirements of the mine's four operating draglines and one overburden shovel. By early 1985 it had become obvious that the existing drill and blast equipment and technology could not cope with the long-term needs of the open cut mining operation. Three 61R drills were in need of rebuilding or replacement. Bulk ANFO trucks working two shifts per day were unable to match the requirements of the four draglines dne to long travel distances, slow discharge rates and their inability to load water-resistant products into the increasing number of wet holes. This paper outlines the significant steps taken to introduce new equipment and technology and the resulting improvements in the mine's productivity and economics.

Jan 1, 1986

Existing production facilities are constantly looking at ways to increase capacity. Many recent solutions have focused on the implementation of capital and infrastructure projects. It is accepted that capital expansions are frequently necessary for production gains; however, in many cases existing assets have the potential to deliver substantially better throughput than they are currently achieving. By focusing on automation of production control systems, production reporting and business processes substantial gains can be achieved utilising existing assets. This potential can be realised quickly and has been proven across several sites and industries. In the Pilbara region of Western Australia throughput gains of between two per cent and 25 per cent (translating to millions of tonnes per annum) have been achieved from existing assets using the methodologies discussed. The improvement process involves evaluating the entire production chain from the time the ore arrives at the plant to the time it is dispatched. A technical evaluation of the performance of the control system and plant automation interfaces to upstream and downstream processes is conducted. The relationship of these processes to the business systems and the human interface to the systems is reviewed to ensure a complete picture of the system is understood. Technical evaluation targets include: individual equipment operation, the engineering level of control systems, feed controls, etc; managing recirculating loads, surge capacities, dynamic inventories as well as management of in-feed systems and integration into yard and out-feed systems; and communication flow between control and other systems, data alignment between rail and shipping schedules, yard systems, sales systems and maintenance systems including such fundamentals as truck dispatch links to plant control. In parallel with the technical evaluation, business system evaluation takes place, including analysis of the operational systems, methods and personnel.

Jan 1, 2007

The extraction of world-class mineral deposits using massive underground mining techniques is not an entirely new theme to world mining companies and experts. Previous MassMin conferences have helped to gather and disseminate the valuable experience and knowledge so important for the proliferation of safe and efficient mining of large underground deposits. With the passing years since the first MassMin conference in Denver in 1981, a number of factors have contributed to an increase in massive underground mining around the world, including environmental pressures, gradual exhaustion of shallower deposits and the enabling effects of improving technology in disciplines related to underground mining. Massive underground mining is heading deeper, embracing challenges which include working with elevated temperatures, increasing in situ and mining induced stress levels and longer ore transport routes. Improvements in mineral processing technology will tend to lead operators to contemplate the extraction of lower grade orebodies in the event that the ore can be efficiently transported to the surface and hence the plant. No doubt this tendency, and its associated challenges is encouraging a rich growth in innovative engineering in such fields as mine planning and materials handling as well as geomechanical issues such as support design and the simulation of extraction sequence effects on stress re-distribution. MassMin 2000, we are sure, will showcase a wide variety of new contributions in thought and actions in these fields. There is a definite place for academic institutions and mining related suppliers in the process of developing new technologies and practices in support of present and future endeavour in this field. Dyno Nobel has its own part to play, certainly as an enthusiastic and proud major sponsor of MassMin 2000, but also by means of identifying common cause between our Vision and Values and the needs, present and future, of the underground massive mining industry. The critical success factors, which Dyno Nobel pursues are:health, safety and environment, customer relationships and market development, cost optimisation (while maintaining quality), technology and innovation, organisational development, and leveraging capabilities globally. Through the present paper we would like to share some of these values and offer some practical insights as to how their realisation will contribute to the achievement of MassMin goals and needs.

Jan 1, 2000

By L Keeney

Geometallurgy is not a mechanism designed to replace current geological and metallurgical deposit characterisation but an added component required to understand orebody variability. Current geological characterisation approaches focus on understanding deposit genesis aimed at identifying new mineralised regions and metallurgical characterisation determines parameters required for engineering design of processing plants. Geometallurgical integration has the task of drawing on aspects of each stream to enable spatial mapping of performance indices across a deposit. It is a complimentary activity to current practice and adds a new dimension to orebody knowledge. Although the notion of conducting an integrated geological and metallurgical analysis is not a new concept, limited publications exist in the field proposing integrated methods, with several technical issues existing in current geometallurgical integration approaches. An iterative method drawing on existing geological and metallurgical characterisation and new measurement tools and inputs is proposed. The integrated method comprises of discrete components dynamically linked together through iterative feedback loops with each component having a specific purpose achieved by applying a range of data acquisition technologies and statistical tests. The key outcomes of the method are:overcoming the lack of optimised geometallurgical domains relevant to processing performance,development of a rigorous approach to identifying parameters controlling processability,improved protocols for relevant metallurgical test data and sample selection, andability to generate greater data support to enable rigorous geostatistical modelling of geometallurgical attributes. This paper outlines the integrated mapping and modelling method developed and draws on multiple data acquisition technologies applied within the AMIRA P843 GeMIII Project.

Sep 5, 2011

Barrick Gold Granny Smith Mine is currently undergoing conversion from an open cut operation to an underground mine at the Wallaby deposit. The underground project commenced in 2005 with the development of the reserves immediately below the pit and is now currently entering a production ramp-up phase for mining of these two initial surfaces below the pit. With increasing gold prices the owner has been forced to re-evaluate the underground project and has decided to investigate the potential of a deep level mine. This deep level underground mine presents a collection of challenges with the most notable being exploitation of a series of well separated near horizontal lodes ranging in thickness from less than 1 to 20 m. A variety of room and pillar mining methods are employed for extraction with careful consideration to resource recovery and pillar design for long-term stability. Compounding these deep level challenges is a need to accelerate mine level development to maintain the production profile of the mine. This paper describes the challenges, key learnings and outcomes of the studies undertaken to date associated with this project.

Jan 1, 2008

By G S. C Murray

Major mining projects are developed with the assistance of lending institutions who provide hundreds of millions of dollars in funding over several years, and of course expect those funds to be returned with interest. Two Australian banks have adopted the Equator Principles, an emerging financial industry benchmark for assessing and managing environmental and social risk in project financing. Project financiers have encountered environmental and social issues that are both complex and challenging, particularly with respect to projects in the emerging markets of Asia-Pacific and elsewhere. There are many recent and historical examples of failures by resource companies to effectively manage their environmental, social, safety and security risks, some of which have caused the project to fail completely, and some of which have caused the temporary cessation of production. These events put the financial institutionsÆ funds at risk through inadequate management capacity and non-compliance adversely affecting the ability of the borrowers to repay the loans. They can also reflect adversely on the reputation of the lending institutions. In assessing these risks, lenders are increasingly looking at the track record of the borrower in its country of origin and in other countries where it operates. Lenders are wary of companies that have one standard for operations in a developed country, where the regulatory environment may tightly control what they do, and another standard for operations in countries where the regulatory regime is perhaps less stringent. Lenders may require environmental and social reviews or audits to be conducted on their behalf by competent third parties prior to a loan being approved, and annually over the life of the relationship. The mining industryÆs concept of the unwritten æsocial licence to operateÆ is highly relevant in relation to the delivery of community benefits that are sustainable post-mine closure. This paper provides examples of recent practices that support financial viability and sustainable development, as well as examples of some failures that have put lenders at risk.

Jan 1, 2007

A cry that is often heard from front-line employees, particularly as a mine grows or circumstances change is "We used to be one big team but now they have set up teams for different functions - we don't know what's going on and we don't share resources any more. We used to just get in and do what had to be done, now we can't.". It usually occurs after management decides that, with the increasing mine complexity, functions and accountabilities of a manageable size need to be identified and defined for individuals and teams to facilitate optimum performance. However, as the statement indicates, these changes have often not delivered all the intended benefits. This paper will explore the reasons why the full benefits have not been realised and will identify actions which can be taken to improve the likelihood of optimal outcomes.

Jan 1, 1998

By S Hanrahan, S McLaughlin

A case study is presented that details the safety journey at a North American project involving two major contracts: a 1000 m shaft recovery and rehabilitation, and the development of a drainage gallery in a large open pit operation. In the early stages of the contracts, there were a number of incidents that created tension between the owner and contractor, which resulted in the contractor being placed on a final warning with almost imminent potential termination. As a result of this, it was agreed to initiate a focused safety recovery plan as a ‘last chance’.Over a period of two years, the engagement and consequent performance of the contractor was turned around, steadily working to set it up for success such that in one of the contract work areas, a record of ‘one year LTI (lost time injury) free’ was achieved. The journey involved the owner and the contractor teams working cohesively to educate all parties in the safety requirements and, most importantly, providing the context and understanding for certain requirements being put in place. Early on in the process, it was recognised that the owner team unknowingly was an impediment in that they did not fully understand the safety requirements and so was not able to lead the way for the contractor effectively. The journey to rectify the situation was supported and followed up by focused engagement with the project team, which generated a progressive improvement in a very challenging environment.In particular, the contractor turnaround was significant and of enough value for the contractor to ultimately export some of the safety systems from this site to other contract sites. This demonstrated the ultimate benefit of the contractor understanding and buying into a safety culture and system.CITATION:Hanrahan, S and McLaughlin, S, 2016. Winning the safety battle, in Proceedings International Mine Management Conference, pp 181-186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

A New Cell for Electrochemically Aided Flotation

Sep 13, 2010

Detachment of Particles from Bubbles in a Stirred Cell

Sep 13, 2010

By P Odins

Traditionally, stratigraphic deposits have been represented by a large number of gridded surface and product analytical models, related to each other by naming convention. This approach, though suitable for structurally simple stratigraphic deposits, does not lend itself well to addressing the complex style of stratigraphic deposits which are becoming more prevalent. In addition, the sheer number of individual gridded models involved makes it very difficult to keep a consistent audit trail of the overall deposit model. Recently, a new enhanced block model structure known as Horizon Adaptive Rectangular Prism (HARP) models was introduced to address these issues. An HARP model is specifically designed to allow stratigraphic units to be represented with virtually no loss of structural integrity, by allowing the tops and bases of the individual HARP blocks to ‘bend’ in concert with the input surfaces. By bringing together the best of grid modelling, triangulation modelling, block modelling and grade estimation, the HARP model opens up many exciting new opportunities for the stratigraphic geologist or engineer to take their model further than was previously possible. Examples of improvements in modelling methodology using a HARP model include: the ability to represent complex normal, reverse and thrust faulting; the ability to store thousands of additional analytical, geotechnical or calculated variables in each individual block; advanced visualisation, manipulation and plotting capabilities; and the ability to calculate volumes and resources against complex, three-dimensional (3D) solid pit designs. Finally, several ‘real world’ scenarios, illustrating how this advancement in modelling technology can benefit a wide range of mining professionals are detailed. These examples demonstrate how productivity gains can be made in both long-term resource modelling and short-term ‘week by week’ geological modelling as an adjunct to mine planning.

Aug 22, 2011

(Quality can be defined as that which is acceptable to the market and can be supplied with a predictable degree of uniformity and dependability at a low cost. The market for any mining product is downstream processing, whether it be an alumina refinery, a gold processing plant or a flotation plant. The cost of that downstream process is partly dependent on uniformity of its feed material both in physical and chemical terms. With more operations adopting procedures which require quality assurances in line with International Standards, from their raw material suppliers, miners must look to their grade control processes to provide uniformity and predicability.This is not a new concept. The mining industry has constantly been working with ahighly variable raw material supplied by Mother Nature, from whom we cannot demand quality assurances. Through the processes of exploration, resource and reserve definition, long and short term mine planning and day to day grade control an end product has been supplied which consistently meets our customers requirements, in an economic fashion. When any of these processes fail, then penalties are incurred which can range from increased mineral processing costs to loss of markets and in the ultimate case, failure of a mining operation.

Jan 1, 1992

By Pigdon SP, Anderson RM

The production of stabilised backfill at mine sites commonly uses Portland cement as the binder. Calcined gypsum has cementing properties and is cheaper to produce than cement. This paper discusses the strength of fills stabilised with calcined gypsum. Laboratory tests were carried out on specimens prepared from tailings obtained from four different sites to allow for the wide variety of tailings found in practice. The results show that the gypsum-based fills can achieve a strength of I MPa using around two and a half to four times the corresponding amount of cement.

Jan 1, 1998