Search Documents

By D C. S M, J Skudder, R F. Sandenbergh

Metallic sulfide minerals present in most gold ores, Morila gold ore included, often decompose under typical gold leaching conditions. The reactions and their products consume oxygen and sodium cyanide, consequently competing for oxygen and cyanide used in gold dissolution. The resultant effect is to reduce both the kinetics of gold dissolution and overall extraction efficiencies. The present paper discusses results obtained from plant data analysis and laboratory work investigating the problem of higher than expected consumption of sodium cyanide at Morila Mine Gold Plant. Cyanide consumption at the Morila Mine Gold Plant had been consistently running at 46 per cent higher than the expected value without any corresponding increase in gold recovery. In fact, plant data analysis showed an inverse relationship between cyanide consumption and grind, as well as cyanide consumption and gold recovery. Experimental and plant data analysis indicated that better control of the [CN-]/[O2] ratio is necessary for the efficient use of reagents and achievement of higher gold recoveries. Careful control of this ratio at a minimum of eight enabled the reduction of sodium cyanide consumption by 200 g/t, that is, from 650 g/t to 450 g/t. Coupling these experimental conditions with the addition of lead nitrate at 100 g/t improved the overall gold recovery to 93 per cent compared to the average plant recovery of 90.2 per cent over a six-month period. This improvement was also reflected in the leaching kinetics where 70 per cent gold extraction was achieved after four hours, as compared to 59 per cent in the absence of lead nitrate addition. Also of great importance is the fact that the combination of hydrogen peroxide and oxygen gave inferior performance relative to either of the two reagents used separately. This scenario presents an opportunity for excluding hydrogen peroxide, an expensive reagent, and focusing on improving the oxygen addition system to boost dissolved oxygen concentration in the plant.

Jan 1, 2007

IN the course of his employment the Broken Hill Co. the writer has had occasion to use and instruct others in the use of the Shamrock rescue apparatus. This paper deals with the various types of apparatus tested. The common object of the various types of breathing apparatus is to enable the wearer to remain and work for varying periods of time in an atmosphere which is either deficient in oxygen or is poisonous that is, contains carbon monoxide or irritating and irrespirable vapours, such as the smoke from underground fires, sulphur dioxide or ammonia fumes. For any apparatus to be efficient as required in the above paragraph it must fulfil the following conditions;1. Air-tight as regards the passage of the air from the outside to the inside. In atmosphere containing carbon dioxide a slight leak would not render the apparatus useless; but where irritating vapours, such as the smoke from burning oregon and sulphides, are met with, even the slightest leak must be avoided.2. The oxygen supply must be ample, and so supplied that it is not checked by expiration.3. Expiration and inspiration must not be retarded.

Jan 1, 1911

By Elber L, Whiten WJ, Cunningham KD, King GL, Bailey CW, Clay PA

The Savage River Mines concentrator treats magnetite ore at about 300 tonne/h, and produces feed for a pelletising plant. The plant incorporates two parallel grinding lines, each consisting of an autogenous mill, in closed circuit with a screen, a rougher mag- netic separator, a ball mill in closed circuit with parallel cyclones, and a finisher magnetic separator. Significant fluctuations in ore grade and grindability make it difficult to maintain pro- duct size in the narrow range desired, and to achieve maximum possible throughput at the same time, using the present largely manual control system. The present paper describes the develop- ment of a control system based on a mini- computer. It has been possible to implement a scheme of on-line estimation of product size which is sufficiently accurate for use in an automatic control system. The size estimation is essentially derived in terms of plant variables which control the ball mill cyclone cut size. Three control functions have so far been implemented and tested. These are control of the feed rate to the autogenous mill, control of water addition to the autogenous mill, and control of the ball mill sump level.

Jan 1, 1978

By A Torpy, N C. Wilson

Improvements in electron optics, field emission gun design, and X-ray detector technology have led to the development of a new class of microanalysis tools. By combining multiple wavelength dispersive (WD) spectrometers, spectral energy dispersive (ED) spectrometers and cathodoluminescence (CL) data sets, a wealth of information can be collected during routine electron beam mapping and analysis. In this paper, data collection on a field emission electron microprobe equipped with five wavelength dispersive, two silicon drift energy dispersive X-ray spectrometers and a wavelength dispersive linear array optical spectrometer has been automated with the optical, electron and X-ray signals being collected in parallel. To analyse the large hyperspectral data sets we have implemented an autoclustering strategy that can be used to produce a quantitative chemical phase map. The cathodoluminescence spectra can be deconvoluted to produce peak intensity maps, which are then converted into elemental speciation images with quantitative sensitivity down to parts per million levels. Both methods are illustrated using typical mineral processing examples, firstly a Ni-laterite sample is investigated with the fine-scale distribution of Ni examined in detail. Secondly, a scheelite sample with rare earth zoning in mapped and rare earth levels quantified.

Jan 1, 2008

By Sehic OA

One aim of testwork and flowsheet development is to ultimately provide a reliable and flexible plant that is simple to operate and maintain. Testwork can indicate amenability of ores to CIP treatment and provide a basis for process design and economic appraisal. Batch cyanidation and CIP tests are often sufficient for small projects. Continuous multistage test rigs can be operated to simulate plant operation and to provide data for flowsheet optimisation. Operating requirements, gold recoveries and potential problem areas can be anticipated at an early stage with more confidence. Subsequent project development involving decisions on the basic flowsheet, equipment types and general plant arrangements are based on practical considerations and experience. Computer aided process modeling and economic appraisal can be useful in analysing various tradeoffs, firming up the flowsheet and equipment sizes, and in specifying operating targets for the future CIP plant. INTRODUCTION Carbon-in-pulp (CIP) technology which has developed rapidly since 1974 is now accepted as an economically and technically viable process for the efficient recovery of gold. This paper describes testwork and flowsheet development procedures used for CIP evaluation and design.

Jan 1, 1982

Prefeasibility planning and cost estimation of conveyor systems has historically been undertaken by comparing fi xed plant transport requirements to that of similar systems in service. This paper describes the development of a prefeasibility conveyor technical design and cost estimation application using Microsoft Excel Visual Basic for Applications (VBA) platform. The application tool known as D-Convey (Dachshund Convey) was developed with the goal enabling the end user: to develop a technical model for conceptualised conveyor systems, to perform economic analysis on the developed technical model, and to conduct a comparative and risk analysis. An Excel VBA based platform was utilised to draw upon both the analytical and graphical capabilities of a spreadsheet. Some of the features of D-Convey system include a revolutionary dynamic graphical help system, known as the 'information pane' in lieu of traditional help fi les as well as the use of familiar graphical user interface elements such as the MS Offi ce 2007 task ribbon. The D-Convey system incorporates material database allowing for mass handling prefeasibility estimation in other industries; it has been validated at a local quarry.

Dec 6, 2010

By Moskovits EE

Spodumene was recovered from pegmatite by flota.ticn in lAoretory tests and ;pilot-plant, operation using an anionic collector e1 ulsi3.n. i sir_tilar process applied to beryl pegmatite g^.ve encouraging results.

Jan 1, 1963

The Joint' Venture Method is a procedure for assessing the value of exploration properties, particularly those for which resources have yet to be delineated. It aims to convert the terms of an actual or synthetic joint venture into the equivalence of an arms- lengths cash transaction between a willing seller and a willing buyer. This paper sets out one approach to achieving that conversion. It discusses both simple and complex cases and gives some examples from both public and private documents. It also includes some case studies in which the Joint Venture Method of valuation can be compared with values derived for the same project using other methodologies including actual cash deals. The Method has failings in both mathematics and logic. However because it does reflect or simulate an arms-length deal which takes into account past exploration effort and expenditure and an assessment of prospectivity at a particular point in time, it is felt that it can provide a reasonable approximation of trade value or asset value of a prospect, particularly if used in conjunction with other methods.

Jan 1, 1994

By M Ujihira, M Komazaki, K Higuchi, D F

A diesel engine with a misfiring cylinder is likely to break down in a short time when the engine is used without maintenance. The authors have developed a method of detecting the occurrence of cylinder misfiring and specifying the misfiring cylinder by using wavelet analysis and statistical analysis on the root mean square (r.m.s.) values of two kinds of acceleration waveforms. This detection method is considered superior to traditional methods, which require several accelerometers, especially in terms of simplicity. Since the development of the method, research has been conducted on semi-automatic processing of measured signals and signal transmission from the worksite to a remote office. Field tests confirmed that 1 + 105 points of dynamic data could be transmitted through the mobile multimedia network within 15 minutes, and the time for signal processing was within 15 minutes. Final determination on the condition of a diesel engine in heavy machinery could be achieved within 30 minutes. Shortened processing time is expected by improvement of the processing software.

Jan 1, 2003

From the viewpoint of mechanical efficiency, charges should be fully coupled and, upon detonation, should just fail to break the rock in compression. But because mining thrives on its cost-effectiveness rather than its mechan- ical efficiency, the explosive which generates maximum energy per $ should generally be used, even though the mechanical efficiency of this explosive's detonation products may be sub- optimum. Wherever possible, each charge should have a length:diameter ratio of about 20 or more and should shoot to a concavely biplanar free face that is both parallel and reasonably close to the blasthole. Success in obtaining parallel effective faces often demands the drilling of angled blastholes and, hence, will require intensified research and development efforts by drilling manufacturers, especially where hard strong rocks are encountered. Blastholes should be drilled on equilateral triangular grids and fired in a Vl or shallower V-type sequence using inter-row delays which ensure that good pro- gressive relief of burden is achieved. The conventional method of calculating Se/Be values (on the basis of planar effective faces) is often invalid.

Jan 1, 1986

By J Bower

The JORC Code does not specify a definition for ælevel of confidenceÆ. The common approach in the mining industry is to use a certain drill spacing or number of data samples to classify resources by the confidence categories. Another approach includes application of the quantitative geostatistical criteria for non-subjective and consistent definition of the resource categories. This approach, which has become increasingly popular in the mining industry, provides a quantitative measure of the resource estimation uncertainty. In this study, uncertainties associated with the different drilling grids at the Weipa bauxite deposit (Queensland, Australia) have been modelled using conditional simulation methodology. Criteria used at Weipa for defining resource categories are as follows: mineralisation can be classified as a Measured Resource if tonnage and grade of its volume representing three months of production can be estimated with a precision error not exceeding ¦10 per cent (at 95 per cent probability, ie two standard deviations); and mineralisation can be classified as an Indicated Resource if grade and tonnage of its volume representing annual production can be estimated with a precision error not exceeding ¦10 per cent (at 95 per cent probability). Several different grids have been created by subsampling the drill hole database. The studied variables include Al2O3, SiO2, thickness of the bauxite seam and location of the footwall contact. The variables have been modelled by sequential Gaussian simulation. Based on this study the following drill spacings have been recommended: Measured Resources û 150 m by 150 m, Indicated Resources û 300 m by 300 m.

Jan 1, 2009

By R Farana

The future challenges in mining instrumentation, mainly on future intelligent mines, are to continue providing instruments with the highest level of reliability at the lowest possible cost, and also to take advantage of technology existing in other industries and to adapt it to the mining context. New wireless instruments (smart sensors, smart actuators, smart controllers) would also be very useful, as well as instruments fully adapted to the monitoring of large movements that are observed, in both underground and open pit mines. Mining instrumentation is found to various degrees in most mines, both open pit and underground. Smart mining instruments present a certain number of aspects specific to the environment in which the instruments are installed. Namely, the instruments can be installed either for short-term or long-term purposes. The mining industry is always looking for useful instruments that can provide relevant information on ground behaviour adjacent to mining stopes or permanent infrastructure. The instruments must meet the various criteria, and must also evolve with the new mining technologies that are continuously being implemented. A strong collaboration between the mining industry, research organisations, and instrument manufacturers is the key to meeting these objectives. This contribution describes the current trends on smart sensors and smart instrumentation with Wireless LAN support.

Jan 1, 2003

By Chen Z, Dong H

This paper describes the autogenous carrier flotation of 0 - 20 ¦m ilmenite using 40 -- 80 }tm ilmenite as carrier. Investigation is made of the influence of main technological parameters on autogenous carrier flotation. The mechanism of autogenous carrier flotation is discussed using extended DLVO theory. The main conclusions are as follows: 1. the smaller the fine particles the more easily they adhere.to carriers; 2. the selectivity of autogenous carrier flotation depends on the selectivity of adsorption of collector. In the autogenous carrier flotation of ilmenite/plagioclase mixture assaying 15.35 per cent TiO2, a concentrate containing 47.17 per cent Ti02 can be obtained by primary separation with a recovery of 93.05 per cent. KEYWORDS: Autogenous carrier flotation, extended DLVO theory, ilmenite, styrylphosphonic acid.

Jan 1, 1993

The paper is introduced by some general comments on the Electrolytic Zinc Company West Coast Mines operations. An outline of the geology of the Rosebery Mine orebodies preced- es a resume of the mining methods used prior to the current mechanization programme. The reasons for the introduction of longhole stoping techniques are given together with a brief explanation of both sublevel longhole and longhole stoping methods. The application of remotely controlled loaders within these stoping methods is discussed. A description of the remote control mechanisms, used on Atlas Copco 310 and 511 Cavo loaders, is followed by comments on these mechanisms from both a maintenance and production viewpoint. A summary of perform- ance statistics and operator safety records vindicate the selection of remotely controlled loaders for the longhole stoping areas at Rosebery Mine.

Jan 1, 1977

By B Ascott

As a prerequisite to achieving integrated regional production reporting across multiple sites, Newmont Australia initiated a project to standardise the configuration and use of mine control systems at three underground sites. This paper outlines the project and considers the outcomes which, in a number of cases, have exceeded the original objectives.

Jan 1, 2008

A three-dimensional finite element analysis is used to determine the stress intensity factors associated with the chevron-notched semi-circular bend test specimen. The stress intensity factor calibration is done over a range of crack lengths a

Jan 1, 1998

The mechanisms of fragmentation in homogeneous materials and structured rock mass are reviewed. A method previously used to predict vibration damage to the remaining rock is extended and shown to be valid for the prediction of fragmentation in the rock mass removed by blasting. The effectiveness of different explosives in different types of rock blasting is discussed.

Jan 1, 1990

By Brouwer G, Shaw J

As South African gold mines go deeper, and improved and more uniform working condi- tions are required, ever larger amounts of refrigeration are needed. At the same time new and more suitable cooling equipment is becoming available for use with new mining layouts as well as on existing shaft systems. The advent of the large diameter rotor screw compressor has meant that there is now a machine available with great flexibility in performance and construction for efficient underground use. The first installation using this type of machine is described.

Jan 1, 1988

By Quinn P, Robertson G, Agar GE

The replacement of diphenylguanidine (DPG) for separating INCO Bessemer matte with a water soluble collector requires a frother since most collectors do not have frothing properties. The objective of this study was to identify a non persistent frother which produced a deep froth and collapsed rapidly, while maintaining acceptable metallurgical separation. Incremental rougher flotation tests failed to differentiate any metallurgical benefit through the use of a specific frother, so other tests were employed to identify the candidate frother. The equilibrium froth height and rate of froth collapse (froth stability) of several commercial frothers were evaluated as a function of frother concentration using a 'frothmeter' apparatus. Frothers evaluated were methyl isobutyl carbinol (MIBC), Pine Oil, triethoxy butane, Dowfroth SA1263, Dowfroth 250C, Dowfroth 200 and Allied Colloids CRNI-1002. Dowfroth SA1263 produced the largest froth height, and TEB had the greatest rate of froth collapse. Frothers with properties similar to Dowfroth SA1263 and Dowfroth 250 were rejected due to their persistent froths. TEB was rejected because it has a low flash point and Pine Oil could be a nuisance to add to a flotation column. Therefore, the preferred frothers were declared to be Dowfroth 200 or Allied Colloids CRNl-1002.

Jan 1, 1993

The overall mineral assemblage of the Broken Hill orebody is similar to that of a skarn. However unlike the classical skarns it does not represent contact metamorphism of pre-existing limestone beds. It is a stratiform accumulation of exhalative-sedimentary silica, sulphides, (Ca, Fe, Mn) silicates and carbonates, fluoride and phosphate that has later undergone regional metamorphism. The resulting development of coarse-grained quartz, sphalerite, galena, rhodonite, bustamite, mixed carbonates, fluorite, apatite and many minor phases has produced a sulphide-rich skarn- like mass that like many others of its kind, might best be referred to as a stratiform skarn. Recent investigations of occurrences of this type are showing that the incidence of concentrations of particular metamorphic minerals in and adjacent to such orebodies are closely related to bedding and to former sedimentary facies patterns. From this it appears that the mineral assemblages may be used to deduce not only the nature of the materials laid down in the beds, but also the physico-chemical conditions under which sedimentation took place. Several stratiform deposits, including Broken Hill, are used as examples to show that variations in these conditions may have a profound influence on the subsequent response of the rock to regional metamorphism and hence on the mineral assemblages that finally develop.

Jan 1, 1983