Search Documents

By H Ş. Duzgun

It is expected that the future of mines will heavily adopt autonomy. However, problems with leveraging workforce transition, meeting Sustainable Development Goals, SDG’s (poverty, reduced inequalities), managing uncertainties (geologic, operational, economic), cybersecurity (connectivity, cyber-physical infrastructure) and innovation (transformative processes, real-time decision-making etc) are required to be solved for the intended autonomy. These problems also impact the safety of the future mine environment. The AI technologies provide a broad range of opportunities for enhancing mine safety. However, development of an accurate AI model for mine safety requires a large number of data, which may not be readily available to overcome the associated uncertainties in the mine environment.

May 5, 2022

By H Asche

The proposed Rockwater Power Project is a hydropower development on the Waitaki River in the South Island of New Zealand. The proposed development will have an installed capacity of 250 MW with a peak flow capacity of 260 m3/s. The project commences at Lake Waitaki and extends some 35 km downstream on the north bank to a surface power station at Stonewall. Flow is returned to the Waitaki River via an outfall channel.The tunnelling for the project is through Greywacke, which comprises Permian and Triassic age marine sediments that are well indurated and weakly metamorphosed. The rock mass is jointed and sheared and there are frequent faults, which range up to hundreds of metres in width. Three 12 m diameter tunnel boring machines (TBMs) are proposed to excavate the 35 km long tunnel.The paper describes the development of the tunnel alignment, rock mass classification, design of the support, rock and hydraulic loads, support installation options and construction sequencing.The alternatives of rock bolts and shotcrete and segmental lining were both investigated and are discussed. Support using rock bolts and shotcrete offers the potential of rapid construction with minimum support cost when the ground conditions are good, but delays due to support installation increases with deteriorating ground conditions. In contrast, segmentally lined tunnels offer greater certainty in cycle time with reduced program risk. Both options are described and discussed.The horizontal alignment is affected by the presence of major fault zones, which are either avoided, or pretreated by driving conventional tunnels through in advance of the TBM delivery, topographical constraints with the rugged topography and operational hydraulic constraints. Construction requirements, future power station operation and the minimisation of leakage from the tunnel have all impacted on the vertical alignment.The number and sequencing of TBMs to be used is discussed in terms of program time and risk minimisation.

Mar 8, 2011

By G Mudd, N Haque, S A. Northey

Life cycle assessment (LCA) provides an internationally standardised framework for estimating the environmental impacts associated with products or services (International Organisation for Standardisation, 2006). A particular strength of LCA is the ability to consider indirect impacts that occur at different stages of a product’s life (eg raw material acquisition, manufacture, use, disposal or recycling) and through its supply chain (Figure 1). A wide variety of impact categories are able to be considered by LCA, such as the potential contribution to global warming, ozone depletion, marine eco-toxicity or freshwater eutrophication.CSIRO has a long history of using LCA to compare the environmental impacts associated with alternative mining, mineral processing and metal production technologies (Haque and Norgate, 2014; Norgate and Haque, 2012, 2013). These ‘mine-to-metal’ assessments have primarily focused upon estimating embodied energy and greenhouse gas impacts associated with these production processes; however, more recently there has been a refocus to also consider consumptive water-use impacts in more detail (Northey et al, 2014).CITATION:Northey, S A, Haque, N and Mudd, G, 2016. Water-related data requirements for improved life cycle assessment of mining, mineral processing and tailings management, in Proceedings Life-of-Mine 2016 Conference, pp 16–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By B Liu, W J. Zhang, S Saydam, B Li

Rock bolts are commonly used to reinforce ground in underground mining and civil tunnel environments. Rock bolts serve two main functions: i) they suspend large, loose blocks of ground, and ii) provide a protective pressure arch to restrain the deformation in an excavated void. Automated and precise tracking of rock bolt positions can assist with the operational success of ground support by reducing the amount of labour required in current manual practices. A point cloud is a large list of x, y and z coordinates in three-dimensional space, that when visualised, show a precise 3D representation of a physical environment. Point cloud data can be collected using accurate LiDAR scanners. These scanners can be mounted on a stationary tripod or on a moving vehicle. A key way point cloud data is used is in the bolt detection project being completed in conjunction with UNSW Sydney, which aims to provide an automated location of underground rock bolts from LiDAR scans. The immediate challenge with identifying rock bolts is that they constitute a very small portion of the data set amounting to approximately 0.01 per cent of some of the collected civil tunnel data. The process of detecting rock bolts from point clouds therefore requires a quick elimination of large background data while still preserving the bolt data. A further challenge is that the geometry of underground environments can often be very complex and non-uniform. To overcome these challenges, a two-step coarse to fine deep learning approach is taken. The first step is a coarse background elimination step aimed at removing as much of the background data as possible. The second step is a finer classification method, which uses deep learning to further segment the bolts from the remaining background. Additionally, a computer vision module is being implemented, which is expected to increase the detection rate by adding another dimension to the training data set.

Nov 29, 2022

By Bluhm S. J, Feio L, Ramsden R

A new mining area at the Vaal Reefs gold mine is to have a shaft. system which will extend to a depth of 4 200 m and will require 130 MW of cooling. A novel feature of the proposed cooling system is a large underground air cooling installation in which an ice slurry is sprayed into the ventilation air. The design of the ice slurry bulk air cooler, in the form of counter.flow cooling towers, is discussed. Comparative thermal tests with cold water and ice slurries (with ice mass fractions up to 22 per cent), were carried out in a 5 m high test tower. The presence of the ice in the water spray increases the resistance to heat flow and reduces the overall thermal characteristics of the air cooler by 8 per cent. Notwithstanding this, the use of ice slurries is indeed beneficial in terms of overall costs. It is concluded that a 25 MW air cooler should use 410 kg/s of ice slurry with a 10 per cent ice mass fraction to cool 550 kg/s of air which is 75 per cent of the total air flow rate.

Jan 1, 1988

Much interesting data on cemented carbides has been published over a period of years which, when classified and pieced together, gives a clear picture of this special branch of powder metallurgy. This is an attempt to present the essential information in an ordered account.THE HARD CARBIDES-THEIR PROPERTIES AND PREPARATIONThe so-called hard or refractory carbides are the carbides of a number of metals which are grouped together in the Periodic Classification. These metals are in groups IV, V and VI. They are titanium, vanadium, chromium, zirconium, niobium (columbium), molybdenum, hafnium, tantalum and tungsten. These carbides have attracted the attention of chemists because of their remarkable properties. They possess very high melting points, and are rather difficult to prepare in the pure state. Their outstanding propertyis their extreme hardness, which they share with certain other carbides, such as those of silicon and boron. In addition, these compounds possess distinctly metallic properties, such as lustre (in fused specimens) and high thermal conductivities.(l)t They are capable of forming alloys in two ways:1. With metals, particularly those of the iron group. 2. With each other (a case of solid solubility).The constitution of these substances is not that of ordinary salts, which obey the usual valency rules, but must be likened to that of certain intermetallic compounds. Actually they are "interstitial" compounds(2), that is, they are formed from the ordinary metallic lattice by the insertion of the relatively small carbon atoms in the interstices.. The energy required to fill the lattice completely is high, and this explains the difficulty often found in obtaining the exact stoicheiometric compound. Thus the carbides can have a range of composition, and can be considered as solutions of carbon in the respective metals.Physical Properties of the CarbidesThe hardness of these compounds is so great that it is difficult to compare the individual compounds on this basis. Becker(l) gives values on Moh's scale, which are not very accurate and are of no great value. Burden(3) has reproduced a diagram by Hatfield which indicates that the cemented carbides are between 1,400 and 2,000 on the Vickers diamond scale. However, the pure carbides are harder, tungsten carbide being about 2,200. Hoyt(4) describes a method of measuring hardness applicable to powdered specimenswhereby the powder is rubbed on a standard block of cemented tungsten carbide under standard conditions, and the rate of wear is determined. In...

Jan 1, 1942

By S Grant, S Emeric, P Baker, E Jones, D Clark

As we strive for a sustainable and resilient future, repurposing assets has become a top priority. In Australia alone, we have a significant number of mineral projects in the pipeline, extensive existing operations, and over 50 000 legacy sites. Collectively, this presents a unique opportunity to be a world leader in mine rehabilitation. Complex stakeholder landscapes, inflexible policies, aged regulatory frameworks, technical uncertainties and increasing liabilities are all barriers hindering effective transition of legacy assets. The impetus for change is further catalysed by shifting consumer preferences, workforces in flux and regional Australians questioning what the transition means for their local community. We need innovative approaches to take a leading role in the industry and support global efforts more broadly. Co-designing an ambitious, shared vision spanning projects, operations and legacy assets with all key parties is a fundamental step to unlock and realise maximum societal, environmental, economic and reputational value. Serious play and gamification can further enhance this visioning process.

Aug 2, 2023

By K McSweeney, A Marton

This paper discusses the development of a strategy for ensuring long-term geotechnical stability of final pit walls at AngloGold AustraliaÆs Sunrise Dam Gold Mine. The strategy makes use of improved blasting techniques, changes to the mining sequence and other geotechnical techniques. Only the blasting techniques will be discussed in this paper. These were developed from numerous trials over a period of several months from May 2003 through to November 2003. The focus was to reduce crest loss damage and thereby improve final wall integrity, maintain designed safe berm widths, and ensure long-term stability. Crest loss mechanisms are now understood and are explained in this paper. The preferred solution is outlined; which is a combination of improved blasting and changes in the mining sequence to cater for pre-existing ground conditions. These ground conditions include dynamic hyper saline water with sometimes intersecting steeply dipping discrete structures. Project requirements were defined as mitigating or eliminating crest loss using 127 mm diameter pre-splitting and targeting minimal production blasting vibration levels against the walls. Blast results were measured by post blast visual inspections and video. Blast design input utilised the predictive algorithms built into simulation software when attempting to minimise vibration levels against the walls. Protection of the already fired pre-split line is now achieved using small charges against the wall and timing sequences which form a mask for the later firing main charges. The pre-split spacing is now modified to suit the geology. There eight blast domains identified around the perimeter of the pit, each having varying joint orientation. In addition, blasting the bench adjacent to the berm crest has particular considerations not required by the middle and lower benches. The preferred solution was to purposefully translate this damaged top section of the pre-split bench into a planned subsequent dig zone. The design of this top æweightÆ is a direct response to the nature of the crest loss mechanism.

Jan 1, 2004

By Stevenson I, Dickinson W, Taylor R. N

Despite flash smelting's widespread use little is known about the actual processes taking place in flash furnace shafts and comparatively few reports of sampling campaigns have appeared in the published literature. his paper reviews the previous reports of the use of horizontal trough samplers and analyses their expected collection efficiency. In the light of the deficiencies revealed by this analysis an isokinetic sampler was produced and a vertical sampling technique was also developed to obtain samples from directly below the burners in the shaft of the flash furnace at the Kalgoorlie nickel smelter. Comparison of the sizing of the samples obtained with the horizontal trough and isokinetic samplers confirmed the theoretical analyses and showed that the trough samplers were not collecting the fine particles. Besides providing data to validate mathematical models of the burners and shaft, chemical analyses of the shaft samples showed that the coal in the charge was reacting preferentially and that the plume of at least one of the burners was being deflected from its axial position. In the region directly below the burner there was evidence that the disperser on the burner was imparting more momentum to the coarser particles and that these were concentrating in the outer regions of the particle plumes issuing from the burners.

Jan 1, 1992

Owing to the 'creeps' and consequent movements in the mines, followed by the recent fire in the southern workings, the whole of the orebody above the 800 ft. level is now very much crushed and broken. The same applies to the hanging wall or overwall coutrny, which has subsided towards the workings, so that for some years past all development work within the lode has had to be carried out with extreme care.The continual but slow subsidence of the overburden into the stopes necessitates a periodical renewal of all gangways in the lode, and, as the subsidence amounts to as much as 60 ft. in places, these new gangways must necessarily pass through the mullock-filling of old stopes in addition to broken ore. They at times pass into the broken ground of the hanging-wall for some distance, where the orebody has widened underneath by the original folding and puckering.

Jan 1, 1932

Estimation of the semi-variogram is basic to the geostatistical processing of data. The most widely used arithmetic average estimator is here employed with various sampling patterns to calculate experimental semi-variograms in a deposit which is simulated to have a defined semi-variogram. Percentage differences between theoretical and experimental semi-variograms are reported.

Jan 1, 1984

By R Dunne, G Lane, S Ha, D Dreisinger

The paper outlines the 17 Mt/a Telfer Project plant process design from sample selection to feasibility study design. The 366 Mt Telfer mine reserve consists of a diverse range of copper and gold mineralisation, from massive sulfide reef ores to stockwork ore, oxide copper minerals to chalcopyrite, siltstone to competent quartzite, all with relatively high levels of gravity recoverable gold. The complexity of the orebody demanded a flexible plant that could recover copper and gold values by a combination of gravity recovery, flotation and concentrate leaching. The demands of treating ore from a high grade underground mine and a variable grade open pit (that includes underground old mine workings) necessitated a dual train approach from primary crushing to concentrate production in order to minimise the requirement for campaigning of different ore types. An extensive sampling, testwork and technical evaluation program was undertaken to identify processing characteristics and the optimum process route for each ore type. The design experience included: the development of robust primary stockpiling and pebble crushing concepts; detailed review of scale-up of SAG and ball mill pilot plant data to plant scale; the selection of two 15 MW SAG mills and two 13 MW ball mills for the grinding circuit; and detailed modelling of the pyrite concentrate carbon-in-leach (CIL)/sulfidisation acidification recovery thickening (SART)/acidification volatilisation recovery (AVR) process to optimise design for copper and cyanide recovery from leach liquors. The Telfer plant design also measures the development of process design based on experiences at the Cadia Hill Cu/Au concentrator, commissioned in 1998. The differences between the two plants are compared and contrasted.

Jan 1, 2003

By J Pan, C M. Tang, D Q. Zhu, C C. Yang, S W. Li, Z Q. Guo

The short process of electric furnace steelmaking with direct reduction iron (DRI) as raw material is an important process for smelting high-quality and special steels. In order to prepare high-quality DRI, the pellets with basicity of natural basicity and 0.4 were prepared from magnetite concentrate (MR=0.09, MR=0.4) and hematite concentrate (HR=0.02, HR=0.4). Based on the HYL method, the gas-based direct reduction experiments were conducted under the condition of rich hydrogen (H2/CO = 2.6). The reduction index (RI), reduction swelling (RSI), cold compressive strength (CCS), and phase changes of the pellets were systematically studied. The results show that the RI of four kinds of pellets is greater than four in the temperature range of 800~950°C. For the magnetite pellets, at a fixed reduction temperature, the RSI increases and then gradually decreases, reaching a peak between 50 per cent and 80 per cent. Moreover, the RSI enhances with the increase of the reduction temperature. In general, the RI, RSI, and reduced CCS of the MR=0.09 pellets are better than those of the MR=0.4 pellets. For the hematite pellets, the maximum RSI decreases from 23 per cent to 17 per cent during hydrogen-rich reduction, while the compressive strength increases from 500 to 1070 Nꞏpellet-1. The main reason is that the glass phase generated by the increase of basicity adheres to the surface of hematite grains, hindering the contact between reducing gas and particles. As a result, the apparent activation energy is reduced, which is not conducive to the reduction process. In addition, the glassy phase attached to the hematite reduces the migration rate of Fe2+/Fe3+, resulting in a difference in the reduction expansion rate of hematite in the inner and outer layers of the pellet. Thus, concentric cracks are formed inside the pellets, the RSI increases and reduced CCS decreases.

Sep 18, 2023

By Frfas C, Parrilla F, Regife J. M

A project to develop the Zinclor electrowinning cell to industrial size is being conducted at Tecnicas Reunidas' Research and Development Centre with Spanish Ministry of Industry support. This project is the final development phase in zinc electrowinning from a chloride medium, the highest ZINCLOR technology development level prior to the industrial scale having already been reached. This paper covers the outcomes and conclusions corresponding to project Phases 1 and 2: Process Selection and Industrial Electrodes (1 m2) design and testing. The most important achievement reached is that there are presently available industrial cathodes and anodes for the Zinclor diaphragm cell giving an optimum response for zinc chloride electrowinning with unit power consumptions between 2.65 and 2.80 kWh/kg Zn, depending on the diaphragm type. Standard electrolysis conditions were: 65 g/L ZnC12, 3 g/L HCl, 160 g/L NaCl, 350 g/t Zn arabig gum as the addition agent, 36¦C, and 400 A/m2 current density. The selection of electrodes, diaphragms and organic additives for the industrial scale tests have been optimised. The complete electrowinning cell development, with electrodes having an active area of I m2, enables the evaluation of Zinclor Technology application for industrial processes.

Jan 1, 1993

By L Y. Yang, Z Wang

This work presents the fundamental properties of CITIC magnetite concentrate and its performance in pelletising and sintering. CITIC concentrate has been widely used in pelletising to produce pellets for blast furnaces. It is also used in sintering to benefit from its sintering performance. CITIC concentrate has excellent balling properties owing to its size distribution, particle surface properties, large specific surface area and balling index, leading to strong green pellets and product pellets. When used in sintering at appropriate levels, sinter bed permeability improves, productivity is increased while coke consumption reduces, and sinter strength improves.

Nov 8, 2021

Gold was determined directly in eight different mill cyanide solutions, by atomic absorption spectroscopy in an acetylene-air flame. Some of the mill solutions were diluted with water to bring them into the most sensitive absorption region (5-50 p.p.m. Au) whereas those solutions with very low gold content «2 p.p.m.) were concentrated by evaporation.Calcium was complexed with ethylene diamine tetra-acetic acid (EDTA) to avoid the undesirable effect of a precipitate on atomization.When added to standard gold solutions, EDTA had no effect on absorption, nor did any of the impurities common in mill cyanide solutions.Known amounts of gold, ranging from 2 to 30 p.p.m., were added to mill solution'aliquots and recovered to within 100 ± 2·5 per cent. For duplicate determinations under normal worKing conditions, standard deviation was 1·32 p.p.m.Excellent agreement was found between atomic absorption gold values and accurate fire assay values.INTRODUCTIONAtomic absorption spectroscopy has been shown to offer a rapid and accurate method for the determination of trace amounts of a number of metal ions. In the field of primary metallurgy atomic adsorption has been used for routine determinations of lead, copper, silver, zinc, cadmium and iron in a variety of raw materials and intermediate products.The scope of atomic absorption spectroscopy was reviewed recently by Willis (1963).The noble metals silver, gold, platinum, rhodium and palladium were determined by atomic absorption from chloride solutions by Lockyer ·and Hames (1959). In their determination of gold down to 1 p.p.m., they found no interference from the noble metals, nor from considerable excess...

Jan 1, 1964

A laboratory size solvent extraction apparatus has been constructed, which incorp- orates three stages of countercurrent extraction, followed by two stages of counter- current stripping. The model uses a gravity flow system from one stage to another and air lift pumps to recirculate organic and aqueous phases. A novel pump/mixer system is used to transfer solutions from the mixer compartments to the settler compartments. The model has proven valuable in the teaching of solvent extraction principles.

Jan 1, 1999

At last year's. annual meeting of The Institute, Sir George Fisher, as President, compared it somewhat nostalgically with a meeting of its kind in the 1920s when comment was expressed on the decline of Australianmining and on the lack of new mineral discoveries.I feel that tonight's annual meeting is even more an occasion for nostalgia, for it represents the seventy-fifth anniversary of the founding of The Australasian Institute of Mining and Metallurgy. I hope, therefore, that I may be allowed to retrace some of the circumstances of this Institute's origin and at the same time to look at some of the broader happenings of those 75 years.From this distance in time it is, of course, much easier to get things in perspective and one of the things that compels enormous admiration in looking back over the history of our Institute is to note the qualities of foresight and keen concern for professional standards which moved the pioneers in this Institute. They had no benefit of hindsight to aid them.Just over 75 years ago, a small group of men met in Broken Hill to discus.s the possibilities of forming an association of mining engineers. The moving spirit was Uriah Dudley, our first secretary, manager of the Umberumberka mine at Silverton. The first formal move to form an association of mining engineers came from the Amalgamated Mining Managers Association of Australasia. At the time, this association was a fairly new group, being 5 years old.It had been formed to try to raise the standard of management throughout the industry. Uriah Dudley and our first provisional president, John Howell, held their first talks in 1891 and further meetings at Broken Hill followed. The inaugural meeting, attended by 200 members, was held in Adelaide in April, 1893.

Jan 1, 1968

By Bigu J, Grenier M. G, Knight G

Particulate control is a major concern in underground mining and the subject of continuing research world wide. In Canada the federal government's Mining Research Laboratory at EIIiot Lake, Ontario, has been using two aerosol counters to aid its investigations. Specific studies with the units include: a) evaluating total and elemental size efficiencies of dust filtration units: b) characterizing the dust particulate cloud from different mining operations: and c) determining dust transportation characteristics.

Jan 1, 1988

By M Tessier, M Pahkala, L Sletmoe

The Red Lake mine is one of the richest gold mines in the world. The primary mining methods are overhand and underhand cut and fill. Starting in 2003, Goldcorp initiated an expansion program at the mine. The expansion includes a new 6.55 m diameter hoisting shaft currently under construction. The shaft will be driven to a length of over 2180 m. The shaft will be used as a primary ventilation intake to the mine. In addition to the new hoisting shaft, a return air raise is being driven approximately 1690 m from surface. This raise will be a parallel return to the existing mine infrastructure. This paper describes the ventilation and climatic analyses performed in support of the expansion project. The study included a full mine ventilation survey, in situ rock mass measurements, analysing options related to mine layout, airway sizing calculations, air heating options, and climatic simulations. Specifications were prepared for an air heating system and main and booster fans. Analyses were also performed related to heat in the stoping areas namely caused by auxiliary fans and backfill with high cement content.

Jan 1, 2005