Search Documents

By M Shaffer, D C. Grant, D J. Goudie, P Sylvester, C Voisey

Scanning electron microscope–Mineral Liberation Analyser SEM-MLA can be used to discriminate between hematite/magnetite in iron ores, but achieving backscattered electron (BSE) segmentation between the two minerals is difficult for particles =75 µm using typical preparation and analysis methods for the MLA based on a tungsten filament SEM (Quanta 400) with 25 kV high voltage. Preparing iron ore sample mounts using a slow-speed polishing method, and conducting the experiment on a field emission gun SEM-MLA (Quanta 650) with the high voltage (HV) setting lowered to 15 kV reduces instrument noise and results in very clean BSE images and segmentation. This method requires new X-ray standards to be acquired for each mineral identity at 15 kV because of major changes in the spectra at lower kV. However, once these X-rays are added to the mineral reference list, effective segmentation can be achieved and a proper analysis obtained.CITATION:Grant, D C, Goudie, D J, Voisey, C, Shaffer, M and Sylvester, P, 2017. Discriminating hematite/magnetite via scanning electron microscope–mineral liberation analyser in the - mesh size fraction of iron ores, in Proceedings Iron Ore 2017, pp 541–548 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Browner R, Lincoln F. J

The activity of silver in solid gold-silver alloys (electrum) has been measured with an electrochemical concentration cell based on the super ionic conductor silver-i3-alumina in the temperature range 200 to 80oaC.The measurements of the silver activity in the range 0.5 to 90.0 atom per eent silver were found to be highly reproducible although there is some disagreement with an earlier study which used a similar technique. At temperatures above 400° the silver activity exhibits both positive and negative deviations from ideality in the silver rich region.This method suggests a simple technique for the nondestructive determination of silver in electrum alloys.

Jan 1, 1983

ZINC concentrate, produced at Zeehan by flotation from Read Rosebery ore, is also dried and roasted at the same place for the production of a calcine suitable for use in the electrolytic zinc process at Risdon, Tasmania.DRYINGThe concentrate, dewatered to 12% moisture by an American filter, is fed into a dryer, the type of construction of which is similar to that of a duplex Edwards furnace. The dryer is 45 ft. long and 14 ft. wide, and has two rows of nine rabbles each, the two pairs nearest the firebox being watercooled.The longitudinal distance between rabble-centres is 4 ft. The rabbles are rotated at a speed of 3 r.p.m. by a I5-h.p. motor. Zinc concentrate is introduced by a screw feeder, consisting of two parallel-blade conveyors, revolving in opposite directions at aspeed of 31 r.p.m.Draft is supplied by a Sirocco fan, 15 in. intake, operated at 1340 r.p.m. by a 10-h.p. motor. The dust carried by the exit gases is removed in a wooden scrubbing tower, 3 ft. 6 in. x 4 ft. 6 in. x 27 ft. high, to which the fan delivers, and down which water issprayed.Wood (eucalyptus timber) is used as fuel, the consumption per ton of water evaporated being 0.55 :ton. Zinc concentrate from the dryer passed either to trucks for shipment or to Herreshoff furnaces. The portion for shipment is withdrawn at a point half-way down the furnace, being loaded on to a belt conveyor for transfer to railway trucks. The moisture at this point is 7% to 8%.

Jan 1, 1927

The Honourable Neil Pickard has been in Parliament for something like sixteen years. He was Minister for Education in 1976, served as Shadow Minister in a number of portfolio areas while his party was in opposition, and since their return to power in 1988, he has been the Minister for Minerals and Energy. Ladies and gentlemen, I ask you to welcome the Minister, the Honourable Neil Pickard.

Jan 1, 1989

By R Kroukamp, G Rech

CRONIMET Australia in cooperation with Speciality Metals International, the mining lease holder of the Mt Carbine Tungsten mine, have demonstrated the preconcentration and processing of large (>12 million tonnes) tailings and mine waste dumps on site in far north Queensland. The first stage of this project has proven the economic viability of preconcentration using sensor-based particle sorting whilst ensuring high recovery of industry critical tungsten minerals – wolframite and scheelite. Sensor-based sorting technology have enabled the production of a sorter product to feed the existing wet gravity plant ensuring higher recoveries and increasing concentrate production. Processing of 1,000 tonne low grade samples using the TOMRA x-ray transmission (XRT) ore sorter installed on site, has reduced the volume of material entering the downstream wet processing plant by up to 60%. The sorted 10-25mm size range produced the highest upgrade ratio (product/feed) of 24:1 and achieved sorter concentrate grade of 1.52% WO3, sorter waste grades below 0.014% WO3 and metal recoveries of up to 93.4%. The appropriately sized, barren sorter waste material is also sold as aggregate and other quarrying products and thus adding to the overall economic benefit of the project. The utilisation of the sorting technology on site has produced an economically viable project, significantly reduced capital cost, and reduced the time to market of the final tungsten concentrate. The next phase of the project includes design and installation of a larger two sorter plant capable of over 150t/h feedrate.

Nov 10, 2020

By Whang K, Choi H

A study of flocculation of ultra-fine coal particles by ultrasonic waves was investigated on a laboratory scale.The coal suspension was dilute, with low ionic strength, and at pH 6·2.When a stationary sonic wave is set up in a solution containing suspended coal particles, it is believed that high and low pressure regions are alternately established at the half wave-length of the sonic wave and this resultsin the migration of coal particles towards the low pressure regions.As expected the flocculation is more effective as to frequency and the power of the ultrasonic waves is increased.The shape and size of the test equipment are also important variables.

Jan 1, 1977

By J Manuel, N Ware

Ideal iron ore sinter is produced by optimising the balance between coarse (+2 mm), stable ore nuclei and a reactive matrix consisting largely of fluxed -1 mm fines. The authors have previously published work evaluating the matrix melting behaviour of a number of fine ores, using techniques developed by CSIRO. The focus of that work was to demonstrate the contribution of the matrix to overall sinter quality, with the results showing a direct correlation between melting point, matrix porosity and strength. CSIRO has also developed a complementary test to study the behaviour of coarse ore nucleus particles in contact with the sinter matrix and provide an evaluation of their reaction and assimilation properties. This test provides valuable fundamental information that can be used to better understand the role of specific ore types and optimise blend composition.The CSIRO laboratory-scale assimilation test is carried out by embedding particles of ores of specific sizes into a fluxed matrix of known sinter blend composition, using real ores and fluxes, in a laboratory test that directly relates to pot-grate and plant sintering conditions. Samples are fired under controlled conditions in a tube furnace using a standard heating profile and a constant, low-oxygen potential atmosphere. These conditions simulate the actual sintering process while removing the effects of the many locally-variable parameters (eg temperature, oxidation potential and localised chemistry) that exist in the actual process, meaning that trends in behaviour can be more clearly seen. Designed as a compromise between the industry-standard pot-grate sintering test and a more fundamental test using chemical reagents, the aim is to isolate and evaluate the nucleus behaviour of an individual blend component to allow an improved understanding of the role that an individual ore plays in a specific blend. Measured cross-sections of the resulting fired samples provide a semi-quantitative measure of reactivity, while accompanying photomicrographs allow a qualitative assessment of assimilation properties (eg volume and distribution of secondary porosity generated during reaction).In this paper, to complement the previous work published on melting behaviour, nucleus particles were selected from hematite, hematite-goethite and goethite ores and embedded in a simulated plant sinter matrix. Drilled core particles of two sizes were tested at fixed temperatures simulating low- (<1300°C) and high-temperature (>1300°C) sintering conditions. The resulting assimilation properties are compared and discussed as a function of particle size, temperature and ore/sinter mineralogy. The implications for the contribution of each component to the prediction of blend sinter quality are also discussed.CITATION:Ware, N and Manuel, J, 2015. Fundamental nucleus assimilation behaviour of hematite- and goethite-containing ores in iron ore sintering, in Proceedings Iron Ore 2015, pp 77–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A Melkumyan, K Silversides

The banded iron formation-hosted iron ore deposits located in the Hamersley Ranges of Western Australia contain marker shales that are used to distinguish lithology for geological and orebody mapping. These marker shales produce distinctive signatures in the natural gamma downhole logs, which are conventionally manually interpreted. This paper proposes an alternative method of automatically identifying these shales using dynamic time warping (DTW). A Gaussian processes (GPs)-based method for automatic identification is also considered. Both methods are tested on a deposit that contains the Marra Mamba sequence of the Hamersley Province.Both methods were trained to predict the location of the desired shales, and the resulting outputs were compared with a manual interpretation of the results to determine the accuracy. The GP method can identify signatures with an accuracy between 87.0 per cent and 92.0 per cent, which increases to 92.9 per cent and 95.7 per cent where the GP is certain. The DTW method has an accuracy between 90.0 per cent and 91.6 per cent, which increases to 94.0 per cent and 95.4 per cent where the DTW is certain.The GP method has several advantages, including a more automated library building process, a probabilistic output and a shorter run time. However, the DTW method was capable of accepting more distortion in the signature and therefore identified more signatures. This is important in a deposit where the signals are frequently distorted by events such as hydration and folding. Both methods provide a viable alternative to the current manual detection, but their differences make them applicable to different cases.CITATION:Silversides, K and Melkumyan, A, 2014. Comparison between Gaussian processes and dynamic time warping for classification of marker shales in iron ore deposits, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 177–184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By B Taylor

The Perseverance deposit is the most southerly known economic copper/gold deposit within the Cobar gold field. The deposit is situated approximately 12 km to the south-southeast of Cobar and is essentially blind to surface with the top of economic mineralisation occurring 750 m below ground level.Based on the December 2010 resource estimate (inclusive of reserves and net of depletion) the deposit contains 3 011 000 tonnes at 6.1 g/t Au and 0.90 per cent Cu (590 000 oz of gold and 28 000 tonnes of copper). The deposit is comprised of four principal lenses, the Perseverance, Hulk, Zone B, and Hercules lenses. In excess of 90 per cent of the known resource tonnes are contained within the Perseverance and Hulk lenses. The deposit is shear related and hosted within lower Devonian rocks of the Cobar Basin. The competency contrast of rhyolites juxtaposed against sediments by the Peak-Perseverance shear is the principal control on mineralisation. Both the Perseverance and Hulk lenses are primarily hosted by brecciated rhyolites juxtaposed against Chesney formation sediments across the Peak-Perseverance shear. This faulted rhyolite sediment contact roughly defines the global orientation of the deposit. The Perseverance lens continues within the shear for up to several hundred metres beyond the extent of the faulted rhyolite sediment contact. Mineralisation within the shear beyond the faulted rhyolite contact zone is hosted by sheared silicified sediments. The Perseverance lens remains open at depth and to the south.The Zone B and Hercules lenses, which are significantly less important in tonnage terms, are hosted by rhyolite breccias within the main body of the rhyolite and appear to be only tenuously related to the Peak-Perseverance shear. Within the Perseverance lens, the presence of northeast trending high grade breccia veins developed oblique to the north-south trending shear system has led to the development of steeply north plunging high grade ore shoots within a globally north-south trending mineralised domain. These high grade shoots have limited horizontal continuity but significant down plunge extent.The presence of coarse gold and the resulting strongly skewed nature of the gold grades, in conjunction with controls on mineralisation which are not parallel to the mineralised domain, has led to predictive difficulties regarding stope performance.Strong heterogeneity of the gold content of the ore and geological controls on mineralisation which are not parallel to the global trend of the mineralisation impose a set of difficulties which sound geological control is helping overcome.

Aug 22, 2011

Mining of narrow vein mineralisation, invariably depending on the mining method selected, involves the extraction of both ore and waste rock. The level to which mining of waste rock can be minimised depends on numerous factors, but particularly the thickness and dip of the deposit. Resue mining is a method of mining that allows split face firing within stopes to allow waste and ore to be mined separately, allowing dilution to be minimised. This paper examines the technique of resue firing and its applicability to the mining of narrow vein deposits. Particular emphasis is placed on the conditions in which resue mining presents a suitable option for mining of narrow veins.

Jan 1, 2008

By F Soleimani

Coal and gas outburst is a common hazard in coalmines and due to the complexity of its nature, efficaciously predicting the possibility of its occurrence is intricate. The mechanical and gas flow properties of coal, in situ and mining-induced stresses and geological structure are involved in outburst occurrence, whereas suggested thresholds for its prediction do not consider them all. Numerical modelling is known as an effective method that can not only consider couple the effect of different physics but also analyse the effect of associated parameters. In this paper, a coupled fluid flow and geomechanics model has been developed in COMSOL Multiphysics to simulate outbursts by considering the effect of gas pressure and composition, damage mechanics on related coal properties, and progressive excavation and mining-induced stress. For the proposed fully coupled outburst model, the effect of pore pressure and sorption are applied to the stress while the influence of stress changes and damage are considered in updating coal porosity and permeability in each time step. In addition, to study the effect of mining-induced stress, the excavation process is simulated by changing the material properties over time according to the schedule of heading development. Then, outburst initiation is analysed from the energy point of view by using the concept of energy conservation law. The simulation results are used in calculating energy sources of the outburst initiation, also, the effect of particle size and ejection velocity are studied, and the significance of particle size effect on the energy analysis and deformed coal on outburst initiation is discussed.

Oct 12, 2022

By R Shrimali, P Rajmeny, L Shekhawat, A Joshi

Rampura Agucha open pit mine has successfully been excavated to a depth of 320 m, incorporating multistage working. The key to success is the implementation of presplitting as control blast measures at every stage of mining, including intermediate cut backs, in addition to the final wall. The major challenges encountered in establishing presplitting in the hang wall as compared to the footwall of the mine are:reversely dipping foliation, ie dipping into the hang wall itselfstriking obliquely at an angle of 20–30° with regards to the general strike of the pit wallthe presence of numerous geological planes of weaknesses like major faults, slips, etc.Control blast parameters like hole inclination, spacing and stand-off with buffer row were chosen initially from the literature survey and were subsequently fine-tuned by field trials to the mine geo-mining conditions of the hang wall. Electronic initiation used for trim blasts along with double presplitting in fault-affected zones helped in getting better presplit performance and resultant stability of the hang wall.CITATION:Rajmeny, P, Shrimali, R, Shekhawat, L and Joshi, A, 2015. Establishing the design parameters of a control blast for long-term stability of the hang wall at Rampura Agucha Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 437–446 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P Corbett, P Sheffield

Centennial Coal operates the Springvale longwall mining operation which extracts coal beneath the Newnes Plateau in the Western Coalfields of New South Wales. Springvale, and the neighbouring Angus Place mine, have a history of difficult geotechnical conditions where combinations of a relatively high stress regime and weak, laminated roof and extensive geological faulting has led to numerous roof failures throughout the mine’s life. Following development, the mines underground roadways can experience high levels of roof movement which may lead to roof falls. Multipoint wire extensometers are extensively used throughout the mine for roadway condition monitoring, and to reactively drive remedial strata support through trigger action response plans (TARPs).As a result of the use of high-density extensometer monitoring over a long period, the mines have an extensive archive of legacy data. Data processing has evolved over time in order to accommodate the increasing data volume, including direct data entry from the recently introduced hard-wired real-time monitoring instruments. It is likely that telemetric real-time instruments will be introduced in the future, which will cause another step change in data management requirements. This paper discusses the transition to and evolution of relational database management systems for extensometer and associated data.This paper also presents case studies of the use of a new software tool for reprocessing legacy data to enable time-scaled visualisation of monitoring data in the context of longwall and development face positions and installed strata support. The software can be used proactively in the identification of geotechnical risk factors and their interaction with the mining process to allow a more robust geotechnical hazard process. It interfaces directly with the widely used ExtoChart database software and can be presented with scale drawings of geological and geotechnical data to allow correlation of monitoring data results with risk factors.CITATION:Corbett, P and Sheffield, P, 2015. The use of high-intensity monitoring data to better characterise geotechnical properties of a non-homogeneous rock mass, in Proceedings Third International Future Mining Conference, pp 145–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By B Bamford

High speed diamond cutting has extensive applications in civil and mining engineering. A project involving the diamond sawing of black granite is investigating the nature of the diamond cutting process. A sawing machine was devised to adjust the cutting load and measure cutting speed. Cuttings were collected for size distribution analysis. The surface produced by interaction between diamond. grits and the rock was subjected to microscopic investigation. Increasing load prompts the proportional increase in the cutting rate. But the mean size of cuttings shows little change. The photomicrographs of the cutting tracks indicate neither patterns of crack formation nor signs of the ductile behaviour of the rock. A diamond cutting model for hard rock is formulated on these observations. Diamond cutting is a process of surface failure, which advances in four stages. The polycrystalline characteristics of a hard rock and the action of high-speed diamond grits guarantee the creation of crack nuclei which develop into cracks in various directions. This network crisscrossing cracks enable the stripping of this surface layer from the rock.

Jan 1, 1992

By S McKinley, S Juras, E Uludag

More and more, today’s mining geologists are asked to identify and create 3D value domains for multidisciplinary usage: grade definition, geometallurgical performance and geotechnical characteristics, to name a few. Often, that domain shape is the result of an assumed or conjectured value as a surrogate to a set of conditions (eg kaolinite-rich, sericite alteration). Would it not be instead better to create the respective domain through identification of a consistent quantifiable geologically-based pattern as its basis?Critical to the identification of patterns is the transformation of 3D point data into a model by a method that uses few, if any, preselected thresholds. Too often we complicate the reviews of the modelled data by prejudging the value range of interest. And when we do revert to 2D views (ie sections and plans), we tend to only examine numbers or line traces. These hinder and obscure identification of geological patterns particularly in deposits of complex geology. Instead, these data should be looked at with minimal prejudgment and interrogated in 2D space by one of the best and most eye-catching display types: filled contour plots.Here we present two different processes that transform data with minimal preselection into formats that allow for pattern recognition by filled contour plots. These are: probability assisted constrained kriging (PACK) and multiple interval interpolant formation (Aranz Geo’s Leapfrog® software). The former creates a 3D model of probabilities on a threshold value; the latter creates numerous (=10), regularly-binned 3D interval interpolants. The results of each method are examined as filled contours over numerous sections or plans. Any distinct patterns are quickly discerned thereby readily identifying the best value to base the creation of a domain. These processes therefore provide a way to marry recent advances in software tools with what is supposed a geologist’s core skill: pattern recognition.CITATION:Juras, S, McKinley, S and Uludag, E, 2017. Pattern recognition in transformed data – the search for domain shapes in mine geology data, in Proceedings Tenth International Mining Geology Conference 2017, pp 37–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By R Simcock

Why Rehabilitate? Legislative Requirement Land rehabilitation is a condition of resource consents for mining. Clause 17 (1) of the Resource Management Act 1991 (duty to avoid, remedy, or mitigate adverse effects) provides the legislative basis for local authorities to impose resource consent conditions requiring land to be rehabilitated to approved uses during and after mining.

Jan 1, 1997

Two continuous computer controlled, remote air analysis (RAA) systems operate at The Zinc Corporation, Limited (ZC) to give early warning in case of an underground fire at ZC or New Broken Hill Consolidated Limited (NBHC) mines. Air drawn from underground sampling points via a tube bundle system is analysed for carbon monoxide and carbon dioxide. An alarm is sounded if the concentrations of these gases exceed bench mark figures.

Jan 1, 1983

By Muldoon T

Water sprays on mining machines are generally put there to reduce dust; however, research by the Bureau of Mines and others has shown that considerable airflows may also be generated by these sprays. This recognition of water spray-gen- erated air movement led to the "Spray-Fan" - a continuous miner auxiliary ventilation system which was shown to reduce methane peaks by a factor of 15. Recent successes and failures of the Spray Fan are reviewed. More recently, the same principles were used in the design of the "Shearer- Clearer" for reducing dust at longwall shearer operators. The original design was successful; however, a new design is now available which is more practical to install and does a much better job of holding the dust against the face downwind of the shearer. The latest research objective is to eliminate the negative impact of spray- generated air turbulence on continuous miner dust control. Most coal faces in the USA are ventilated in the exhaust mode using "line curtain", and the forward airflow on the side of the heading opposite the curtain is inevitably weak. Air turbulence generated by sprays which are incorrectly located and/or operated at excessive pressures can cause roll back - in which the dust cloud at the face is forced unwind against the ventilation and spreads over the miner cnerator. The general approach to reducing "roll back." is reviewed and art anti-roll back water spray system is presented.

Jan 1, 1983

By T Y. Dube

In this paper current net present value (NPV) based mine valuation techniques that take into account market and private risk are discussed and analysed. Potential pitfalls that arise from the application of a portfolio, market or commodity based risk metric to a mining project are identified. An alternative non-simulative framework for quantifying and factoring market and private risk in NPV calculations is proposed and then applied to a hypothetical case study in an attempt to overcome identified pitfalls. Mathematical proof that a static discounted cash flow (DCF) calculation can underestimate or overestimate mine NPV is presented, the conditions for each are outlined and the degree of underestimation defined.CITATION:Dube, T Y, 2012. How the use of market-based risk metrics can undervalue good mining projects and overvalue poor ones, in Proceedings Project Evaluation 2012 , pp 29-34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

Distal air-fall ashes are widespread deposits that may record volcanism many hundreds of kilometres from their source. They are characteristically thin, fine-grained and have a low preservation potential usually being either eroded, or reworked and incorporated in overlying sediments following deposition. The most likely sites of accumulation are deep sea, lake and swamp environments where low energy conditions favour preservation. Post-depositional alteration of predominantly glassy volcanic ash is commonly extensive hampering identification of such layers in the geological record. As a result air-fall tuffs are poorly represented in the rock record and furthermore are commonly misinterpreted. Southeast Queensland during the late Triassic hosted active silicic volcanism and a number of fault-controlled basins in which coal-bearing sediments were accumulating. Silicic volcanics of late Triassic age are represented by the Brisbane Tuff in the Brisbane city area, the Chillingham Volcanics to the south of Brisbane and extending into New South Wales, the North Arm and Mount Byron Volcanics to the north of Brisbane, the Aranbanga Beds exposed around Gayndah and the Agnes Waters and Muncon Volcanics which occur northwest of Bundaberg. Stephens (1986) interprets these Volcanics as the remnants of a major silicic igneous 'province which he likens to modern continental orogenic margins. The Ipswich, Tarong and Callide Basins of southeast Queensland all contain coal measure sequences of late Triassic age that accumulated in alluvial plain environments. A Dicroidium flora is common to all and palynol.ogical evidence indicates a late Triassic (Carnian) age (de Jersey, 1975; Stevens, 1981). The coal seams of the three basins are characterised by their thickness (up to 25 m) and the presence of abundant thin, laterally persistent, kaolinite claystones (tonsteins) that show a marked similarity of morphology, texture and mineralogy. Detailed studies of the Ipswich Coal Measures (Falkner, 1986) suggest a volcanic air-fall origin for the tonsteins of the Ipswich Basin. Similar.tonsteins from the Tarong and Callide Basins provide evidence for widespread silicic volcanism during the late Triassic in southeast Queensland.

Jan 1, 1987