Search Documents

By M Carr, K Williams, W Chen, J Plinke

The depletion of iron ore deposits at the face of the mine site dictates the necessity for the exploitation of formerly less attractive orebodies to meet the demand of the modern world. These orebodies will typically be found close to or even beneath the water table where an increasing clay and moisture content will result. Problematic iron ores, colloquially termed as ‘wet and sticky’ material (WSM), can have a significant impact in the material handling stream due to the expensive downtime of processing equipment, which is attributed to the inter-particle and boundary cohesion and adhesion forces of the bulk material.In order to gain a better understanding of the causes of poor handleability, experimental test methods to determine wall adhesion, and inter-particle adhesion within bulk materials were developed. Based on the combination of wall adhesion and inter-particle adhesion measurements, with traditional methods of assessing bulk material handleability, a new method to assess the potential of bulk materials to cause handling problems is proposed. This method reduces the multitude of factors leading to problematic behaviour to a handleability index (HI) [0,1], which is easily assessed and understood. The method is suitable for adhesive materials and applicable for a wide range of material flow, from gravity reclaim stockpiles to transfer chutes and carry back on conveyor belts.Additionally, this research presents an assessment of the HI derived by experimental testing of three iron ore samples. A clear understanding of the problematic behaviour of the iron ore samples is achieved with the use of dust extinction moisture (DEM) tests, which indicates the regions where problematic behaviour may be experienced on-site.CITATION:Carr, M, Plinke, J, Williams, K, Roberts, A and Chen, W, 2017. Determination of the handleability index of adhesive bulk materials, in Proceedings Iron Ore 2017, pp 503–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The areas of concern lay in the processing of, and the subsequent hearing into, Waihi Gold's resource consent applications to extend Martha Mine. The proposed amendments to the Resource Management Act 1991 might see the introduction of contestability in the processing of applications - which would have assisted Waihi Gold; and the use of commissioners to hear the applications, with a right of appeal to the Environment Court on points of law only. It is also proposed to have major applications heard directly by the Environment Court. If Waihi Gold's applications had been heard at first instance by the Court, the delays in time and associated costs would have been reduced. However a hearing by commissioners only would not have been satisfactory, there being no right of appeal against the conditions of consent, which if implemented as granted by the Councils would have had a significant impact on the costs associated with the extended project.

Jan 1, 1998

By R C, K L. Rees, J S. J van Deventer

In contrast with previously published models for the carbon-in-pulp (CIP) process, the model proposed in this paper incorporates film transfer, intraparticle diffusion, simultaneous leaching, preg-robbing, the loading of multicomponent species, and the effects of fouling and changing cyanide levels. The rationale behind this comprehensive model is that changes in fouling and competitive adsorption along a CIP cascade affect the profiles of gold loading. As it is impossible to quantify all these non-ideal factors, a method is proposed whereby an imaginary species is postulated so as to combine all the competitive effects. A plant survey at the Telfer mine has shown that the mass loss due to a gravimetric analysis of the fouled carbon could be used directly to quantify this competitive effect. The degradation and consumption of cyanide along the Telfer CIP cascade enhance the loading of copper on to the carbon, which should be taken into account when modelling the gold profiles. It appeared that the effect of cyanide itself on the loading of gold was negligible compared with its effect on the copper. Evidently much more research is required on this topic in order to optimise CIP operations exposed to constantly changing conditions.

Jan 1, 1998

The general types of industrial behaviour of liberated valuable sulfide minerals in the 0 - 10 ¦m size fraction are described and tests to explore on site at a concentrator the general nature of any deficient behaviour are discussed. In addition, the general types of behaviour of the gangue minerals in this size fraction are also described in terms of their mechanisms for recovery. These behaviours are also discussed in terms of the type of grinding device and grinding environment in which they were produced and the target grinding product size. Major recent improvements in the industrial capabilities of grinding devices are discussed.Present difficulties in characterisation of particles in the 0 - 10 ¦m range are described and desirable improvements for the future are outlined. Further, desirable improvements for industrial processing of valuable minerals in this size range are discussed along with some remedial actions.

Jan 1, 2005

Local conditions at Hatches Creek are described, together with the mineralogy, mining and treatment of tungsten ores, with particular reference to procedures adopted by Pimer Mines, N.L.The Hatches Creek tungsten field covers an area of about 20 square miles in: Central Australia; 285 miles' N.E. of Alice Springs. Access is by rail to Alice Springs, then by 200 miles of bitumen highway to Barlo Creek and 8,5, miles of bush track to the field. Passengers can also reach the mines by... A semi-desert climate prevails Rain; generally in the form of thunderstorms falls in the summer months: December to March. Average annual rainfall is approximately 15 inches but there is great variation from year to year, occasional droughts being followed by torrential downpours. Vegetation is sparse except in the wide creek beds. Surface water occurs in rock holes some of which, spaced miles apart, carry permanent water...

Jan 1, 1955

By A Wanninayake, E Novello, I Gillani

A residue storage facility (RSF) was designed to cater for Davidson Creek Area and Robertson Range Area operations under the FerrAus Pilbara iron ore development project in the Pilbara Region, Western Australia. Annual ore production was about 15 million tonnes over a period of up to 15 years. The RSF was designed to handle a tailings production rate of 2.2 Mt/a over the project life with ability to be expanded at a later date. The composition of tailings was predominantly -45 ¦ material with some spiral reject material. The fraction of solids was expected to be between 40 per cent and 50 per cent solids by weight.The RSF was designed as an above ground storage facility, integrating with a mine waste dump planned close to the selected RSF site. This integration helped to increase the stability of the RSF embankment and to reduce the construction cost. The main source of construction material for the remaining part of the RSF embankment was selected to be mine waste. The RSF was designed to be constructed in stages by considering the availability of mine waste according to the mining schedule. The use of mine waste for construction of RSF embankments has several benefits over use of borrowed material. These include less construction costs and less disturbances to the environment, by minimising borrowed areas and waste dump footprints.CITATION:Wanninayake, A, Novello, E and Gillani, I, 2013. Effective use of mine waste in the design of a residue storage facility, Pilbara region, Western Australia, in Proceedings Iron Ore 2013 , pp 39-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By P N. Holtham

Magnetic separation is routinely used in the processing of titaniumminerals, and the efficiency of these operations can be determined bymeasuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved.This paper describes the development of an inductance-basedinstrument for measuring very low levels of magnetic susceptibilityon-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance.A prototype instrument has been installed in the zircon scavengercircuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction.Using the instrument, the zircon content of this stream can now beaccurately determined from the measured magnetic susceptibility,provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

State ownership of mineral in the ground is not newthe Regalian Right is an ancient concept. And the compulsory purchase of land and the minerals beneath it by the State or a body approved by the State (Fitzgerald, 1952) was a principle well established and enforced in practice over a hundred years ago, when such powers became a practical necessity during the period of railway building in Britain and elsewhere:The acquisition of mineral properties which stand in the way of public construction projects still goes on. But in recent years nationalization is being increasingly undertaken as part of the planned use of national resources, for the closer regulation of economic activities, or merely, so it would seem, as a matter of political expediency or national pride. For instance, the unsevered coal in Britain came under State ownership in 1938 in an attempt to simplify a complex pattern of freehold titles which were impedingplanned mining operations. Later, unsevered minerals became a factor in negotiations arising under various town and country planning acts. The acquisition of the Rio Tinto mines by the Spanish Government implies political aspirations. Or State purchase may even be accidental: it was the easiest course for the Sierra Leone Government consequential upon its failure to prevent widespread trespass over legally-held diamond privileges in 1955.This paper has been prompted by problems that have arisen when properties containing unsevered mineral have been expropriated by the Crown in New Zealand: expropriations, it is true, that have been on a small scale in rela...

Jan 1, 1957

Experimental petrology may be used to accurately constrain PTX conditions in order to calibrate and understand geologic processes. This method may be used to answer postulated questions, by recreating known geologic conditions and observing changes in the experimental charges. The purpose of this project was to determine the eutectic composition and temperature in the ternary system PbS-FeS-ZnS ¦ (Ag2S), at ambient and elevated pressures and elucidate if the sulfides of the Broken Hill orebody may have been partially molten during highgrade (granulite facies) metamorphism. The study determined the eutectic temperature and composition in the system PbS-FeS-ZnS to be 800¦2¦C and 62.5% PbS, 30.5%FeS, 7% ZnS respectively, at one atmosphere, and the eutectic temperature at 27 kbars was found to be 960¦C¦10¦C, with a eutectic composition enriched in ZnS relative to the one atmosphere eutectic. the addition of lwt.% Ag2S to the system depresses the eutectic temperature to 772¦2¦C at 1 atmosphere and below 810¦5¦C at 5 kbars. The conditions of peak metamotphism for the cental and southern areas of the Broken Hill Block, New South Wales, Australia , lie above the solidus of the PbS-FeS-ZnS-Ag2S system, strongly suggesting that partial melting occurred in the orebody.

Jan 1, 1998

By Hara Y, Arino S, Nakamura M, Tachimori M

The theoretical and experimental studies have been done to clarify the hearth flow of iron and slag. The results of dissections show that the hearth can be treated as a packed bed of coke hav- ing good permeability with a coke-free layer at the bottom of the hearth. 3-dimensional numerical calculations of hearth flow with and without a coke-free layer are carried out, and the results are assured by a water model simulation. The influences of a coke-free layer on the iron flow and the discharge route of iron and slag are examined. The 3-dimensional flow pattern can be represented simply by the travelling time, which depends on characteristically the profile of coke-free layer and the quantity of iron in the hearth. Those flow parameters could be obtained by the results of radioisotope tracer test ( Co for iron flow, and Sc for slag flow) at several furnaces. As a result, it is found that the coke-free layer repeats the cycle of appearance and disappearance at several-month intervals. This cycle corres- ponds to large temperature fluctuation at the bottom of hearth. The relation between iron flow and skull (solidified iron, coke and deposited graphite mixed layer) on the hearth brick was studied by the model experiment and the thermal analysis based on the indications of thermocouples installed in the bottom of the hearth. If a thin coke-free layer is formed on the skull, a fast iron flow is generated in the layer, and melts away the skull. The growth and melting of skull produces the fluctuation of thermal load on a bottom brick, causing brick Damage.

Jan 1, 1981

THE Australian States and New Zealand have for many years provided instruction in mining, metallurgy, geology, and their allied subjects through their Universities and Schools of Mines. Though such education has been provided at considerable expenditure, there is no legal recognition whatever given to the holders of degrees, diplomas, or certificates granted by the authorities controlling these educational institutions. Certain of the, Australian States and New Zealand require, however, that mine managers and other officials employed by the mining industry shall 'hold' certificates granted by their respective Mines Departments.The position at present is that each educational institution is practically a law unto itself, and therefore in many ways there is a want of uniformity amongst institutions all aiming at the same result the training of mining men. The object of this paper is, in the first place, to point out certain aspects of this want of uniformity, and thereby how disabilities accrue. Some points in connection with the granting of State certificates will also be...

Jan 1, 1915

Coal cleat and faulting influence failure, gas release, and choice of preferred mining directions, locations, and sequences. Unfortunately soil and younger rock cover restrict direct mapping of these structures ahead of mining operations. Aerial photographs of cover contain indirect indications of concealed structures in arrays of linear photostructures. These arrays are commonly too complex for interpretation by simple visual inspection.Analytical techniques applicable to complex arrays are illustrated for a covered part of the Galilee Coal Basin, Queensland. These techniques are: optical determination of sets in arrays of photostructures; correlation of these sets with sub-surface structures; filtering of m-rays for particular sets; detection of anomalies associated with concealed structures in the density distributions of particular sets; fitting filtered arrays to trajectories; correlation of trajectories with the regional directional variations of concealed structures; contouring of ratios of sets to discriminate anomalies associated with concealed fractures and variations in the total and bed thicknesses of cover; kinematic and dynamic inference on the basis of fracture-trace angular and spatial relationships.

Jan 1, 1979

By J Karlovšek

Civil engineering infrastructures are often subjected to different types of natural and mechanical activities. These influences may result in serviceability or even in stability of structures due to material deformations, increased water content within the materials used or the formation of internal or adjacent cavities that may threaten the infrastructure. Construction practices can lead to development of such defects in the form of cavities. In civil engineering it is crucial to detect these variations in material properties and to detect the presence of defects. However, as they are often hidden from view, these attributes may be difficult or impossible to target with traditional testing methods. For these reasons rapid geophysical methods, such as ground penetrating radar (GPR), are increasingly being used. At the University of Queensland (UQ) GPR is used for detection of voids and cavities which have been caused by an over excavation of the earth pressure balance machine (EPB) operating in a closed mode.A variety of numerical simulations using the finite-difference time-domain (FDTD) methods and preliminary experiments have been carried out in order to specify information about the nature, type, size, location and other characteristics of targets to be detected by GPR. In doing this the difficulty of interpreting GPR data, which is mainly due to the complexity of the factors involved in multiple possible solutions of the observed features, can be overcome.

Mar 8, 2011

Future metal prices play a direct role in both the economic evaluation and short to medium planning of a mine scheduling sequence. It is difficult to predict with accuracy the future price of volatile metal commodities, however, it is possible to fix some future metal price, outside of long term contracts by the selling of futures contracts through a commodities exchange. The futures contract represents a fixed amount of a specified quality of a commodity for future delivery at a predetermined price. Several different types of hedging are possible, one in particular which is best suited for mining companies. There are relative advantages and disadvantages when trading in futures contracts and particular reference is made to gold contracts on the Sydney Futures Exchange.

Jan 1, 1980

By Carlos G. C

Geological mapping in various parts of Australia is revealing a number of regional associations of mineralizations with particular persistent stratigraphic horizons. Such associations have been found in the Broken Hill district of New South Wales, in the Nairne district of South Australia, in the Mount Isa district of Queensland, and in the Cloncurry district of Queensland. The question has arisen as to whether such mineralizations are of sedimentary origin, syngenetic with the enclosing formation, or whether they are of epigenetic origin, and reflect the selective hydrothermal mineralization of favourable beds on a regional scale.The purpose of this investigation is to test the use of sulphur-selenium ratios as an objective method of distinguishing between suphide deposits or sedimentary or supergene origin, and sulphide deposits of hydrothermal origin, with particular application to the districts mentioned. At the same time much data has been accumulated as to the selenium content of Australian sulphide ores. The possible use of sulphur-selenium ratios for this purpose was first demonstrated by Goldschmidt and his coworkers (1933; 1935), and later by Carstens (1941). Goldschmidt and Strock (1935) found that pyrite of sedimentary origin had a sulphur : selenium ratio of the order of 200,000 or more, whereas pyrite of hydrothermal origin had a sulphur: selenium ratio of 10,000 to 20,000. Carstensfound that sedimentary pyrite deposits in Norway contained less than 1 g. Se per ton, whereas hydrothermal pyrite deposits contained 20 to 30 g. per ton.

Jan 1, 1954

Close spatial relationships between the deposits of the Etheridge Goldfield (23 000 kg of bullion) and various regional geological and geophysical features suggest that genesis of the ore deposits was a multi-stage process that started with magmatic and metamorphic stages in the mid-Proterozoic, climaxed with structural and hydrothermal stages in the late Palaeozoic and terminated with an oxidation enrichment stage in the Cainozoic. Acceptance of this hypothesis permits classification of the Georgetown region into areas likely to contain deposits of the Etheridge type and those unlikely to do so. Consequently there is little scope for the discovery of extensions of this field. However, the stratigraphic interval between the source rocks of the Etheridge field and stratigraphically bigger host rocks of the Croydon field may contain disseminated replacement gold deposits of the Carlin type. The potential host (pyritic carbonaceous and locally dolomitic siltstone of the Candlow Formation) is locally faulted and cut by granitoids and the extension of a mineralised, long-standing zone of structural weakness.

Jan 1, 1980

New Developments in Spirals and Spiral Plant Operations Records indicate that spiral separators have been utilised in mineral separation for over 100 years. The Spiral's predecessor, the sluice, has been in use for centuries in different forms and a spiral can be thought of as a sluice wound around a column. The spiral separator is distinguished from the straight sluice, and other flowing film separators, in uniquely introducing centrifugal motion. The elegance of the spiral concept was embraced due to significantly improved separation efficiencies, ease of operation and tolerance of variation in feed conditions. Advances in spiral technology have improved the metallurgical performance, modernised the materials of construction, increased unit capacities and simplified operation. These advances have ensured that spirals continue to play a major industry role amidst other advancing and competing technologies. Recent developments in spiral and spiral plant technology include: the launch of the VHG spiral model, specifically aimed at feeds with very high levels of high-density mineral particles; the introduction of a high capacity wash water spiral model; and innovations in feed stabilisation and control. Details of these developments are presented together with the resultant operational benefits including feed stabilisation, product control and improved metallurgical performances.

Sep 13, 2010

Pilot-Scale Study of Deep Cone Thickener for Phosphatic Clay Dewatering

Sep 13, 2010

THE Broken Hill mining field, approximately 31 miles in length, is at present being exploited by seven companies, viz. : North Broken Hill Limited, Junction North Broken Hill No Liability, Broken Hill Proprietary Block 14 Company, Broken Hill ProprietaryCompany Limited, Sulphide Corporation Limited, Broken Hill South Limited, and Zinc Corporation Limited.The variation in size and shape of the ore-bodies in the mines of these companies, together with the many alterations in pitch and dip, necessitates differences in methods of mining, each company working out its problem in its own particular way.In the matter of chute construction for the handling of the ore broken in the stopes, each mine belonging to the above companies has adopted a style particularly its own, though it may be said that one or two of the types approximate very closely to each other, slight minor differences only being noticed in the design. It is the purpose of this paper to give a brief description of the principal types of chutes now in use in th,e various mines on the field, and in doing so they may roughly be classified into three groups, viz:1. Bulk Chutes, 2. Circular Chutes, 3. Square-set Chutes.The Bulk type of chute is used in the North and British mines of the North Broken Hill Limited, the Central and Junction mines of the Sulphide Corporation, the South Blocks mine of the Zinc Corporation, and the Block 14 mine.The Circular type of chute is used by the Broken Hill South mine and the South Blocks mine.The Square-set chute is used in the Proprietary mine, the Junction North mine, and occasionally in other mines where the square set method of mining is a necessity, and more particularly as mullock passes.

Jan 1, 1925

This paper puts the view that, for one gold deposit in Victoria at least, the Australasian Code for the Reporting of Identified Mineral Resources is severely deficient. The author questions whether or not the Code constrains the proper dissemination of information relevant to resource valuation. The author offers a view about the estimation of inferred resources, and provides data believed pertinent to the proper valuation of Ballarat Goldfields Ltd Ballarat East Project.

Jan 1, 1990