Search Documents

By Pollard D, Meadows N

The presence of impurities which are electropositive to zinc in acid zinc electro- lyte causes changes to deposit morphology and reduced current efficiency. Glue may be added to control some impurity effects, but assaying for animal glue concentration is difficult and seldom done. Measurement of the activation overpotential for zinc deposition by cyclic voltammetry is used in some plants to monitor electrolyte quality and control glue additions. The deposit morphology and current efficiency of zinc deposition from commercial electrolyte were investigated for various glue additions in the presence of increased levels of antimony. Cyclic voltammetry was invest- i,ated as a method of optimizing glue additions in the presence of antimony. Scanning electron microscopy showed deposits characteristic of the impurity element present and the glue addition rate. Cyclic voltammetry measurements showed some correlation between current efficiency and activation polarization potential. The importance of using tankhouse electrolytes where results are to be related to tankhouse operation was noted.

Jan 1, 1984

Production of oic at BHP Minerals Pty Ltd's Cannington Mine commenced in May 1997. The initial sloping blocks at the [nine are located in the upper part of the Footwall Lead lode, and the Hangingwall Lead and Glenholme Breccia lodes. This paper discusses the geological investigations, interpretation and modelling that was undertaken for the Footwall Lead lode production block at Cannington Mine, as well as providing a basic geological introduction to the Cannington deposit.

Jan 1, 1997

By A Thornton, D Engelhardt, J Woodg

Grinding is a critical part of nearly all mineral processing operations. It is the largest consumer of energy on the mine site (and thus indirectly a producer of greenhouse gas through the generation of electrical energy at the power station). Since comminution is one of the main consumers of electrical energy worldwide, efficient control of grinding mills is of paramount importance. Mill Auto-Pilot is a control system developed for SAG mills to stabilise load and power and improve the efficiency of control and increase throughput. A dynamic, mechanistic model of the grinding circuit is used to determine circuit parameters which can not normally be measured using conventional instrumentation. The circuit model is built from models of the unit operations (such as conveyors, SAG mills, cyclones, sumps, etc), and so captures the dynamic complexities and interactions of real circuit operation. CSA Mines at Cobar NSW accepted an offer to be the reference site for Mill Auto-Pilot and the system was installed in March 2004. In this application the model is used to predict mill load mass, mill solids residence time and cyclone underflow density. These parameters are used to control mill load, power and mill discharge density. The outcomes of the introduction of Mill Auto-Pilot at the CSA Mine are discussed.

Jan 1, 2004

Urban railway systems need high invest- ments, especially if their routes and stations have to be placed in the subsurface. In the FRG the construction and equipment cost of urban underground railway systems are in the range of 60 to 100 Mill DM per km tunnel. For this reason, track sections on the surface and on elevated structures are used as far as that is possible. Considering whole systems, the costs are in a range from to 45 Mill DM per km length for a metro system with about 80 % of its tracks and stations in tunnels and from 20 to 25 Mill DM per km for a light railway system with about 25 % subsurface infra= structure. The amount of route lengths in tunnels depends on the size of a city, the situation regarding above ground structure and free space on the surface, the level of service quality which has to be achieved with the railway system etc. Despite of the urgent needs to improve the transport conditions there very often arise doubts if an urban railway system is really necessary and can be justified in an economic sense. The experience from many cities around the world shows, that there arise a lot of benefits from urban railway systems, especially with larger sections placed under- ground. They are to be found in the interests of the operator (f.e. operating costs), the user (travel time, quality of service etc.) and regarding social aspects (environmental protection, accidents, consumption of energy Etc.).

Jan 1, 1987

The present practices in electro-refining of copper are shown to be the result of piecemeal and gradual improvements and innovations as metallurgists responded to changing cost pressures and the availability of new technology.Major changes were inhibited by capital cost restraints and a reluctance to build unproven ideas into new plants.It is suggested that the level of technology available today, combined with the greatest cost pressures the industry has known, call for fundamental re-appraisal and a questioning of widely accepted conventional practices.Examples of the industry reaction to changing pressures are given, and directions for future developments are suggested.

Jan 1, 1985

The Blackwater Coal Mine is a modern open cut operation using large draglines for over- :)urden removal and shovels, loaders and trucks to mine and haul coal to the crushing and coal ?reparation plant. Operations at the mine are described in sequence following through overburden removal to the railing of product coal from the mine site. The close operating connection between the mine and washery, which results from the blending of raw coal into clean product via the qashplant bypass system, is stressed. Some features of special interest at Blackwater Mine, such as land reclamation and slope stability,are outlined.

Jan 1, 1974

By Ooms M, Scott OJ

This paper is concerned with the design and operation of storage and discharge facilit- ies for bulk solids handling. It presents an overview of the basic design philisophy emphas- ising the influence of bulk solid flow propert- ies and bin geometry on the flow patterns developed and how these, in turn, affect the reclaim efficiency and the bin structural in- tegrity and wear characteristics of both bins and chutes. The salient aspects of feeder design and operation will be discussed and the need to consider feeders as integral parts of the bin discharge system will be stressed.

Jan 1, 1978

By Denholm W. T

The SMELT-2 package is specifically designed to perform on-line simulation of smelting processes. This paper describes its application to the simulation of continuous matte converting followed by reductive slag cleaning in SIROSMELT reactors. The matte, containing 50% Cu is assumed to be produced at the rate of 20 tph in a continuous matte smelting furnace such as an Outokumpu Flash Furnace, Noranda or Sirosmelt reactor. Two alternative fluxing strategies in the converter are examined, namely: ò conventional silicate slags, ò calcium ferrite slags, and the flow sheets associated with each strategy are discussed. A regular solution model is used in the present study to account for the variations in the activity coefficients of components in the slag.

Jan 1, 1989

By N Murphy and, S Santomartino, M Cramer

Acid rock drainage (ARD) can have detrimental effects on mining infrastructure, water reuse options and environmental discharge. As a result, some form of short- or long-term treatment is required at many mine sites. Successful treatment depends on a number of factors including the selection of an appropriate treatment technology and its correct implementation. A variety of passive and active technologies are available for dealing with ARD. Passive treatment solutions do not require continuous chemical inputs but take advantage of naturally occurring chemical and biological processes. They are often low cost, site specific approaches and are predominantly used in post-closure situations. Passive systems are well suited to drainage with low acid loads and low soluble aluminium concentrations, and are more effective with highly reduced (ie low oxygen) water. While they are often regarded as permanent fixes, most require some form of ongoing maintenance and all have an engineered life expectancy (ie finite carbonate and organic matter budgets). Passive treatments include, oxic limestone drains, anoxic limestone drains, limestone diversion wells, various reducing and alkalinity producing systems, pyrolusite limestone beds, aerobic and anaerobic wetlands, permeable reactive barriers (organic ¦ carbonate and zero valent iron), slag leach beds, and gas redox and displacement systems (GaRDS). Active treatment solutions require a continuous or semi-continuous activity (eg reagent dosing) to correct water quality issues. They can be engineered to treat virtually any type of drainage or site specific ARD issue, and have no set acid load or redox limitations. Tasks handled by active treatment systems are almost invariably larger and more costly than for passive systems. Active treatment approaches include; pH control, adsorption/absorption, ion-exchange, electrochemical concentration, biological mediation/redox control, flocculation/filtration and crystallisation. A range of generally available and proprietary technologies has been developed around these approaches. Active treatment involving pH correction with alkaline amendments is the most common and cost-effective form of ARD treatment. A variety of fixed plant and portable treatment systems are available. Calcium-based reagents, including quicklime (CaO), hydrated lime (Ca(OH)2) and limestone (CaCO3) remain the reagents of choice for the majority of active ARD treatment worldwide. This is principally due to their widespread availability, non-proprietary nature, and variety of proven dispensing technologies and cost-effectiveness. Limestone, in particular, is a very low cost reagent. However, due to æefficiency of useÆ problems with limestone in passive treatment systems, combined with its very low cost, there has been a recent emphasis on developing active treatment systems that use limestone efficiently. As the requirement for treatment increases, there is a growing emphasis on treatment sludge management and sludge stability. The final choice of a suitable treatment technology is dependent upon water chemistry (eg pH, type of metal contamination, acidity), flow rates, acid load, local natural resources (neutralising materials, topography), climate, site logistics, environmental risk and economics. The benefits and limitations of both passive and active treatment technologies are summarised.

Jan 1, 2003

By C Hertle

GHD-Black & Veatch (GHD-BV) have completed design and specification of the ash thickening plant at Tarong Power Station, including operation of a pilot plant. Construction of the plant is in progress and commissioning is planned for early-2004. The objective of the new plant is to convert the low concentration (lean phase) ash slurry currently generated by the power station into concentrated slurry which will then be pumped to the existing ash dam. Water recovered from the lean slurry will be returned to the power station for reuse. The drivers behind this project are to extend the life of the ash dam and to reduce water pumping costs. A maximum flow of 1000 litres per second is expected in the thickening plant. The process involves a screening phase, which removes large material that could cause blockages or equipment damage. A 50 metre diameter thickener then concentrates the screened lean ash slurry to 55 - 60 per cent w/w solids. In addition, the thickener plant will allow the harvesting of floating cenospheres (hollow, spherical ash particles) from the lean slurry. Cenospheres are currently collected from the surface of the ash dam and drained on a pad adjacent to the dam. The new system will use a surface skimmer to remove the cenospheres from the thickener and transfer them to settling ponds for further classification. The settling ponds simulate the detention on the existing ash dam, and allow entrained fine ash and slow settling cenospheres time to settle. As settling occurs in ponds, the slow settling cenospheres can be completely recovered whereas when they settle in the dam, the opportunity for recovery is lost. Cenospheres are a valuable by-product produced during the combustion process, and recycling of this material reduces the waste generated by the power station. Water recovered from the thickener drains to a three megalitre reservoir. Water is drawn from the reservoir for thickener plant service water and various other uses in the power station. The bulk of the water is used to sluice ash from the power station to the thickening plant. In the current configuration, surface water from the ash dam is reused but must be pumped several kilometres back up to the power station. The dam also holds an inventory of several thousand megalitres of water and has significant evaporative losses. Therefore the current raw water make up demand is substantial. In addition, some areas of the power station traditionally using raw water will be modified as part of this project to allow the use of recovered water, further reducing the raw water demand. The design incorporates many features of sustainable water management. By more effectively recovering water from the lean ash slurry, the amount of raw water make up required by the system will be significantly reduced. This method of water recovery provides a more sustainable and energy efficient ash-transport mechanism.

Jan 1, 2003

Almost all industrial products, such as buildings, cars, plastics, railways, radio and television sets, computers, and others are made from materials extracted from the Earth. Earth is main resource of energy and up to now; the energy has been derived mainly from natural resources. Mining industry has significant influence to the nature, sometimes evokes a devastation of nature. On the other hand we have got a lot of nice examples that good preparation, sensitive mining practice and consistent reclamation can minimise the negative effects. All the mentioned problems calls for effective tools for mine design, mine operation and mine reclamation. Third millennium brings next challenge given by advances in information and communication technology. The development of very sophisticated software tools provides to technical systems some features of autonomous æthinkingÆ and intelligent behaviour. We can find large effort and a lot of scientific papers reflecting last advancement in science and technology and providing inspiration for new mining technology of third millennium called Intelligent Mine. Some aspects related to creation and utilisation of æIntelligent ModelsÆ as a background of æIntelligent MineÆ are presented and discussed in this paper.

Jan 1, 2003

Through the stress synthesis of many exanples of macrostructure from eastern to western parts of China, it can be concluded that in Chinese tectonics there are two push- twisting forces, one of which ("Rl", from SE to NW) came from the Pacific Ocean plate thrusting over the Chinese continent plate in the eastern part of China; the other ("R2", from SW to NE) resulted from the thrusting of the India plate. The meeting line could be situated along the belt from 104¦-106¦E longitude in the middle part of China. To the south of Qinling the meeting line was an abyssal and giant fault situated from Longmen to the Er Inland Sea where the Tibet-Gansi fold system was intersqueezed to the Sidluan platform; to the north of Qinling, situated on the Fengxiang subsidence of the Eerduosi basin, the meeting line was located about 105¦E in Mongolia and appeared in the form of an arcuate structure, i.e. the Mongolia arcuate structure, which could extend to Beijiaer Lake towards the north. A new special type of structure named rotation-apart structure occurred from Gansu, Qinghai province to Ningxia, Neimeng autonomous region, in the west of Shandong province and in the western part of Chaidamu Basin.

Jan 1, 1987

Formed in 1965 to investigate the bauxite deposits on the Gove Peninsula, in the Northern Territory of Australia, Nabalco Pty. Limited undertook to determine the feasibility of establishing a mining operation and alumina plant of at least 500 000 tonne/year capacity. The drilling programme undertaken and the analytical methods, assumptions and criteria used to define practicably extractable bauxite are described. The ore characteristics and the interpretation of results used to evaluate the reserves are detailed. The operating techniques developed in mining ten per cent of the reserves and variations experienced between indicated and actual mining are examined and discussed.

Jan 1, 1979

Roadheaders have had a chequered history in hard rock excavation in Australia since their introduction into the country in 1972. This has resulted in a poor reputation among both clients and contractors and subsequent reluctance to design tunnels and underground space around their performance characteristics.This has now changed because of the introduction into Australia of a new breed of Roadheader, the Mitsui. This paper sets out the history of development of the Mitsui range of Roadheaders. It describes the process which resulted in the introduction of this new machine, its performance to-date and the characteristics which have contributed to the success of the machine. The combination of these factors have led to a change in attitude to the use of Roadheaders in underground excavations.

Jan 1, 1993

By Gill L. F, Gleeson HB

This paper describes the development of a Computer Aided Design and Drafting based mine planning system in the State Electricity Com- mission of Victoria. The system combines a commercially available CADD system with a commercially available mining/geological package. The methodology used in the establishment of the combined system, the fea- tures of the system and the current status of development are discussed.

Jan 1, 1989

By Balks AI

Systematic roof bolting in Australian coal mines began at Elrington Colliery in 19)49. Since that time the proportion of the roof supported by roof bolts has increased until, in 1970, 1.5 million were installed in Australian coal mines. This rapid growth of roof bolting has meant that the range and variety of roof bolting machines has altered also. The-number of machines now available both to bore holes and place roof bolts has increased. to the point where both rotary and per- cussive machines are used extensively. Generally, until the last four years, roof bolting machinery in Australia followed the practices in vogue in the United States. However, in -recent time the particular problems of Australian coal mining have necessitated the development of equipment primarily suitable to Australian conditions.

Jan 1, 1971

By Hopkins G. M F

Intensive exploration of the Archaean ultra mafic sequence bordering the Kambalda dome has resulted in the discovery of at least ten dis- tinct areas of nickel sulphide mineralisation subsequent to the initial drill intersection in January, 1966. Sulphide ore reserves to June 30, 1972 were 19.36 million tonnes at 3.3% nickel after mining of 3.0 million tonnes at 3:7%,nickel since production commenced in March, 1967. About 75% of contained nickel metal reserves occur in sulphide concentrations located at the base of the-ultramafic sequence, in contact with underlying meta-tholeiitic basalt. The remaining reserve occurs in concentrations of sulphides within the ultramafic sequence, usually within 100 metres of the underlying contact and typically in proximity to contact mineralisation. These hanging wall orebodies are smaller, contain significantly lower con- centrations of sulphide, and generally exhibit higher Ni:S ratios than underlying contact ore- bodies. The majority of contact sulphides concentr- ations form narrow, elongate, north north-west trending bodies, closely coincident with fault bounded depressions in the contact. Detailed study of the Lunnon Shoot ore environment in- dicates that it was a locus of crustal failure during, and subsequent to, emplacement of ultra- mafic rocks. Resultant structures parallel and

Jan 1, 1973

This paper outlines the thermodynamic and mass balance principles which affect the distribution of cobalt between matte and slag during the pyrometallurgical treatment of nickel - copper sulphides and considers the implications with regard to maximising the recovery of cobalt from the smelting and converting circuit.

Jan 1, 1992

By N G. Corner

A sea bed sampling programme by CRA Exploration Pty Limited over an area of 12 000 km offshore from Westland, Southland and Otago, New Zealand, led to the discovery of the Harvester Prospect, an area of some 67 km2 which averaged 189 mg/m3 gold in surface samples. This area was in water depths of 70 to 106 m and contained a high grade core of 33 km2 which averaged 283 mg/m3 gold. The gold recovered was fine grained, averaging 124 microns, and indicated a potential resource of approximately 10 t of gold per metre of thickness. Interpretation of existing seismic and geological data suggested that the gold anomaly may be associated with a unit of sediments 10 - 40 m thick, probably deposited during a lower sea level stand. Two initial attempts at vibrocoring the anomaly produced inconclusive results. In 1989 a much more powerful vibrocorer with scaled up support facilities and a dedicated 24 h turnaround laboratory were employed. The final results clearly showed that the gold was from an uneconomic surface enrichment.

Jan 1, 1990

The Split Rock low grade copper prospect was discovered in 1969 by Cyprus Mines Corporation using stream geochemistry. Cyprus "Imes carried out geochemical and geophysical investigations, geological mapping, and percussion and diamond drilling, and concluded that the grade of mineralisation was too low (0.1% copper) to be of interest. In the present study, the geology was remapped and very substantial differences from the previous observations are recorded. (lineraliced acid dykes in a 1 000 foot hole drilled by Cyprus Mines had a total inter- section of almost 300 feet with an average crade of 0.4% copper. Surrounding drill holes at distances of 500 feet did not intersect +hese dykes. This group of drill holes occupies a small part of an area about 2 km by 1 km which was affected by intense quartz sericite pyrite alteration along many fractures with an associated soil copper anomaly. It may be that the quartz sericite alteraiion with feeble copper mineralisation represents hydrothermal alteration emanating `rom a mineralised intrusion of which the dykes mentioned above are off shoots.

Jan 1, 1978