Search Documents

Gekko Systems Pty Ltd have developed the Python Underground Processing Plant for the concentration of gold and sulfide ores. The Python plant has an established flow sheet including fine crushing, screening, gravity separation and flotation which aims to concentrate the valuable minerals (gold/sulfides). The aim of the plant is to achieve high valuable recovery into a mass yield of 10 - 30 per cent to reduce the amount of material that is needed to be taken to downstream processing. This paper examines the test work protocol for testing an ore to assess its suitability for the Python flow sheet. This paper will discuss the test methods employed to determine crushing requirements, continuous gravity recovery and flotation performance and how the results relate to Python design for the comminution, gravity and flotation circuits. Results from past test work will be discussed.

Aug 1, 2010

By C R. Ure

To substantially reduce, if not eliminate, carbon dioxide (CO₂) emissions from ironmaking it is necessary to convert from blast furnace (BF) ironmaking using coking coal as the reductant to direct reduction (DR) ironmaking using hydrogen (H₂) and green electricity. Currently, almost all natural gas (NG) based direct reduced iron (DRI) production utilises iron oxide pellets in shaft furnaces, as opposed to fines in fluidised beds. Also, these pellets are ordinarily produced from high-grade magnetite concentrate, rather than hematite and goethite with typically higher gangue contents. The use of high-grade magnetite concentrate is driven by the preference to melt DRI in conventional electric arc furnaces (EAFs), thereby avoiding the basic oxygen furnace (BOF) for making crude steel (CS). However, in replacing BF with DR ironmaking it is not economically feasible to source enough high-grade magnetite to replace the lower grade hematite and goethite currently consumed. That is not to say that hematite and goethite, or even low-grade magnetite, cannot be used in DR ironmaking. However, their higher gangue content, resulting in higher slag production, requires that the EAF producing CS be replaced with a submerged arc furnace (SAF) that will produce pig iron (PI) for the BOF as does the BF. Here, critical issues to be addressed are, what are the technicalities in replacing high-grade magnetite concentrate with hematite and goethite and NG with H₂ in DRI pellet production and melting? This paper summarises certain relevant published information on DRI pellet research, test work and production together with relevant information on Pilbara ores. It attempts to illustrate the inter- relationship of composition and processing conditions on DRI pellet properties. It is intended to serve as a rudimentary guide to understanding the complexities of formulation, testing, evaluation, production and goethite and offer insight into this challenge.

Sep 18, 2023

By L Lorenzen, H Muller

"Every year a large number of projects are evaluated by small listed and unlisted mining companies that are hoping to find the ideal project, which will catapult them from a mining junior status to that of a mid-tier mining company. Usually this includes finding the æidealÆ or ærightÆ orebody and then developing a process which will allow cost-effective recovery of the valuable metals and the production of a saleable product. These dreams are seldom realised and there are a number of good and obvious reasons for this. Issues that are generally high up on the agenda for the smaller companies are: cost of developing a project before the feasibility study stage finding a suitable, or optimum processing technology financing of the project dealing with risk.The most expensive part of the development process for the small miner is often the exploration side of the business and finding the æidealÆ orebody. However, finding the right orebody will not be discussed in this paper. The æidealÆ orebody does not necessarily solve the problems of the mining junior, as much of the uncertainty lies in the process required to recover and produce the final metal product. Once a mineralised deposit has been identified and the grade at least reasonably qualified, the development of a suitable process becomes the driver to convert the deposit into an orebody. This paper proposes that a small exploration company has a very limited opportunity to succeed if it does not do sufficient homework before it identifies the æidealÆ orebody. The risk profile for the small mining company, by its very nature, has to be different to that of a major company and as a result the opportunities often lie in managing different and often new process options, which may be the key to bring such projects on line successfully.CITATION:Muller, H and Lorenzen, L, 2012. Project selection and process development for mining juniors, in Proceedings Project Evaluation 2012, pp 149-158 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By T Seifert, P Krolop, K Niiranen, S Gilbricht

The Per Geijer iron oxide apatite deposits (IOA) display significant potential mineral resources for Luossavaara-Kiirunavaara AB (publ), known as LKAB. LKAB continuously mines magnetite/hematite ores in northern Sweden for almost 130 years. The Per Geijer deposits reveal a high phosphorus content and vary from magnetite-dominated to hematite-dominated ores, respectively. Furthermore, they show a large variation in texture, mineral composition, and relation to wall rocks. The high phosphorus concentration of these ores results from highly elevated content of apatite as gangue mineral. Reliable, robust, and qualitative characterisation of the mineralisation is required as these ores inherit complex mineralogical and textural features. For this purpose, comminution tests at laboratory scale in combination with scanning electron microscopy-mineral liberation analysis (SEMMLA) were carried out. Based on this work, significant information on the modal mineralogy and degree of liberation of minerals of economic interest (eg magnetite, hematite, and apatite) were obtained. Results show that there is a difference in the degree of liberation of magnetite and hematite between ore types. This seems to be dependent both on the size fractions and the dominance of each iron oxide in the individual ore type. The amount of gangue minerals seems to have no significant impact on the degree of liberation after comminution. Apatite is generally best liberated in ore types associated with silicates, regardless of magnetite or hematite dominance. Based on the results of this study it can be inferred that a high degree of liberation of the minerals of economic interest can be achieved. However, results need to be verified with further beneficiation steps such magnetic separation, apatite flotation and possibly reverse silicate flotation.

Nov 8, 2021

By M J. Gillespie, P D. Erskine

Mine site rehabilitation generally includes the re-shaping of overburden to create a final landform, manipulation of substrates and subsequent revegetation. Due to the wide range of environmental variables that influence rehabilitation progression, having clearly-stated final land-use goals and ongoing significant contributions to the planning process, from prefeasibility through to mine closure, is essential for achieving stable landforms and sustainable rehabilitated communities. Two examples of rehabilitation processes in the phosphate rich region of North West Queensland are used to illustrate some of the possible benefits of early planning and communication of rehabilitation requirements.Approximately 160 km south of Mount Isa, Incitec Pivot Limited operates a 35 year old open cut mine at Phosphate Hill. Monitoring of rehabilitation areas and selected analogue sites is undertaken annually, but the initial landform design, substrate management and species selection has created a difficult environment for revegetated areas to successfully establish. Constant management input (such as weed management, erosion control, supplementary seeding, etc) will, therefore, be required over a long time frame.The second example uses exploratory drilling and historic costean pits at Legend International HoldingÆs Paradise South site, 135 km north of Mount Isa, to determine the success of natural vegetation colonisation on waste rock and compacted soils, and the effects of cattle grazing on recolonisation. This information can be used by planners of the mine life to inform possible end-land use decisions and proposed completion criteria.In a semi-arid environment such as North West Queensland, the creation of a post-mine landscape suitable for nature conservation and/or grazing can be an arduous task. The input from environmental personnel at all stages of the mining process will positively impact upon the quality of the resulting rehabilitation and ensure undesirable legacy issues are minimised.CITATION:Gillespie, M J and Erskine, P D, 2012. Importance of early rehabilitation planning - Case studies from North West Queensland, in Proceedings Life-of-Mine 2012 , pp 187-196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By G N. Musafer, M H. Thompson, R C. Wolff, E Kozan

The most important aspect of modelling a geological variable, such as metal grade, is the spatial correlation. Spatial correlation describes the relationship between realisations of a geological variable sampled at different locations. Any method for spatially modelling such a variable should be capable of accurately estimating the true spatial correlation. Conventional kriged models are the most commonly used in mining for estimating grade or other variables at unsampled locations, and these models use the variogram or covariance function to model the spatial correlations in the process of estimation. However, this usage assumes the relationships of the observations of the variable of interest at nearby locations are only influenced by the vector distance between the locations. This means that these models assume linear spatial correlation of grade. In reality, the relationship with an observation of grade at a nearby location may be influenced by both distance between the locations and the value of the observations (ie non-linear spatial correlation, such as may exist for variables of interest in geometallurgy). Hence this may lead to inaccurate estimation of the ore reserve if a kriged model is used for estimating grade of unsampled locations when non-linear spatial correlation is present. Copula-based methods, which are widely used in financial and actuarial modelling to quantify the non-linear dependence structures, may offer a solution. This method was introduced by Bßrdossy and Li (2008) to geostatistical modelling to quantify the non-linear spatial dependence structure in a groundwater quality measurement network. Their copula-based spatial modelling is applied in this research paper to estimate the grade of 3D blocks. Furthermore, real-world mining data is used to validate this model. These copula-based grade estimates are compared with the results of conventional ordinary and lognormal kriging to present the reliability of this method.CITATION:Musafer, G N, Thompson, M H, Kozan, E and Wolff, R C, 2013. Copula-based spatial modelling of geometallurgical variables, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 239-246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

I feel a little like the Parson delivering his Sunday Sermon, chastizing his parishioners for not coming to Church. Those who need to hear me are absent.Nevertheless, I hope that if you agree with what I am about to say you will go forth and spread the word.We often hear of the impact mining has on the community. I prefer tonight to deal with the impact some community attitudes have on mining, and I want to point out that the results of these attitudes rebound to the detriment of our society. I want to deal particularly with regulation, taxation, and proflts.In a civilization whose standard of living is essentially dependent on an adequate and reliable supply of cheap metals and fuels, it should be evident to Blind Freddie that mining must be encouraged.I must express concern at the constraints inflicted on the mining industry by our community. We tend to blame Government for our difficulties, but we must recognize that Government acts merely as agent for the community. It is fair to say that in a free society, if Government actions do not reflect the demands of the electorate, then it doesn't stay the Government. It is important though for Government, in framing its policies, to ensure that it is not unduly influenced by the loud voices of minority groups.The people of our nation have every right to demand that our industry meet certain criteria to be allowed to operate. We all wish to live in a healthy and congenial environment, and to have our individual comforts protected. It is essential, however, that the community realizes that its demands on the mining industry are affecting Australia's prosperity.Each new regulation and each new tax or impost has its effect on investment, employment, and national revenue. Restraints result in an increase in costs which in turn raises the minimum value of a mineral deposit which is economically mineable. It results in minerals, which could be mined under more favourable circumstances, remaining in the ground, perhaps lost for ever.

Jan 1, 1978

By X Li, J Wang, D Liu, Y Liu, K Hu

"Since the adoption of open-door policy 30 years ago, rapid economic growth has resulted in serious resource depletion and environmental destruction, especially in mining areas. As an urgent response to this situation, the central government and the Ministry of Land and Resources (MLR) have adjusted policies with concrete and realistic actions for halting this trend of non-sustainable mining activities in China. æGreen Mine CampaignÆ is one of the actions implemented. In 2010, MLR announced the æGreen Mine CampaignÆ, in which existing and new mines will be evaluated against the æGreen Mine Construction StandardsÆ and certified as æGreen MineÆ if complying with these standards. The standards cover five key aspects: the considerations of science-supported resource exploitation efficient resource utilisation standardised management environmental friendliness harmonious community relationship.Every year, MLR reviews ægreen minesÆ from all provinces. Thirty seven mines, including coal, metal, non-metal, gold, chemical industry and building materials mines, passed the review and were certified as green mines in 2010. In 2011, 187 out of 194 mines that participated in the review were certified as ægreen minesÆ. These mines are viewed as good examples of sustainable mining development in China.CITATION:Liu, Y, Hu, K, Li, X, Liu, Y, Liu, D and Wang, J, 2012. The green mine campaign and sustainable mining in China, in Proceedings Life-of-Mine 2012, pp 339-342 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

I find that during the short time I have been in this district, the majority of boilers are, and have been, receiving very bad usage owing to the difficulties which they have to contend against, viz., oil and bad water. Oil on the heating surface of a boiler is of a highly dangerous nature inasmuch as it allows the surface to become overheated, owing to the water not coming into direct contact with the plates, and it naturally follows that when the crown sheets of a flue or firebox become overheated, you lose a considerable amount of the strength of the plate, and the flue or crown comes down. Referring to the oil question, I find that too much care cannot or exercised on the part of engine drivers in order to minimise as much as possible the internal lubrication of the various engines under their control. For I consider that it is here that the most of the trouble is caused. My reasons for stating such to be the case, are:-That the majority of enginedrivers before coming to this field have been used to driving engines that have been exhausting into the atmosphere, and probably they have been taught that it is far better to use a little extra lubrication than to have a hot bearing. So far so good. But one thing that must not be overlooked is that on these fields the conditions are altered in this respect, as the majority of engines in this district are not exhausting into the atmosphere, but are condensing their exhaust steam and using the water so condensed for feed purposes.

Jan 1, 1901

By K J. Ward, C N. Hatton, J Scalia IV, C A. Bareither, D L. Spencer

The mining industry is experiencing change in the governance of tailings facilities (TFs). Guidance and regulations across many jurisdictions contribute to this amorphous change. The Canadian Dam Association, Mining Association of Canada, Australian National Committee on Large Dams, and the Global Industry Standard on Tailings Management, produced by the International Council on Mining and Metals, are establishing guidelines for more rigorous industry governance. Evolving guidance regarding TFs is developing concurrently with a shortage of experienced tailings engineers, which adversely affects the resource base available to support new governance. This paper presents an updated semi-quantitative estimate of the impending resource shortage of qualified tailings professionals. Updates are provided herein for the estimated number of TFs worldwide, which included available data on active and inactive TFs, as well as the estimated labor resources required to service these facilities. The tailings labor shortage is discussed in the context of academic and professional training currently available to increase the quantity of trained personnel. This paper represents a discrete moment in time as contributions to the available information and inventories accessed continue to improve, but as of today are incomplete. However, the data and information included provide insight into the resource deficiencies currently within our profession, training and education opportunities to address those resource deficiencies, and a snapshot of a recent professional training course offered on mine tailings.

Jul 1, 2021

By Shklyar FP, Babushkin NM, Bokovikov BA, Fedotov PB

A mathematical model for gas flow dynamics and heat and mass transfer processes occuring in the tuyere raceways and in the zone of the final for- mation and heating of pig iron and slag has been developed and simulated on a digital computer. It takes into account the formation and size of the raceway zones, combustion of coke and its substit- utes, oxidation of the metal, radiation from the gases to the raceway boundaries, physical heat losses and the direct reduction of the pig iron elements below the raceway zones. To evaluate the distribution of heat produced by the oxidation of metal between gases and prod- ucts of smelting, the problem of heating the mat- erials in the raceways with the sources of heat in the materials under conditions of intensive gas circulation in the raceways is solved. To determine the amount of heat transferred by radiation from the gas to the boundaries of the raceways, the problem of radiant heat transfer be- tween two grey bodies forming a closed system is solved. Using the structural parameters of the furn- ace, the inlet parameters of the combination blast and exit parameters of the melt, the model permits the calculation of the temperatures of materials entering and leaving the raceways and also the res- idual temperature of the gases, which qualitatively differs from the theoretical combustion temperature. Analysis of the operation of several different blast furnaces has shown that the overall picture of the interaction between gas flow dynamics, mass and heat transfer processes occuring in the race- ways and in the zone of final product formation, obtained with the aid of the model, now permits us to approach from a different position the deter- mination of the limiting factors in furnace operat- ion. It also allows us to explain certain phenom- ena observed in blast furnace practice and to dis- cover new relationships which may be used in analy- sis and control of the smelting process.

Jan 1, 1981

By R Sterk, B Reid

The Konongo Gold Project is located on the western margin of the 125 Moz Ashanti Gold Belt in Ghana, West Africa. It is situated 60 km along strike of the world-class mineral system at Obuasi and is interpreted to lie on the same controlling regional shear system.The project is operated by Signature Metals, a subsidiary of the Liongold Corporation, and is managed and funded by the Liongold Corporation.Historic underground operations at Konongo produced 1.6 Moz Au at a head grade of 11.8 g/t Au, from eight operations spread along 16 km of the shear system. Mining focused almost exclusively on free-milling gold in quartz, ignoring the gold-bearing sulfide mineralisation associated with the quartz veins. Underground mining ceased in 1986.In 2013, Signature Metals re-focused the program at Konongo to assess the viability of mining the sulfide ore sustainably. This led to the first campaign review of the historic underground data and resource potential since mine closure. The Obenemase mine was the first of the eight operations to be assessed as part of this campaign.Large amounts of legacy data have survived for Obenemase and several historic resource estimations have been completed based on these data. The data typically consisted of hand-drawn sections and plans, and ledgers of commonly incomplete drilling and sampling data. Some drill core have been lost over time, but a large amount of quarter-core and half-core as well as pulps and rejects are still available. Previous resource estimates had a low confidence value because all the available assay and geological data were integrated effectively with the estimates, resulting in a lack of understanding of both grade and geological continuity.This project built a new geological model for Obenemase that greatly enhances the understanding of the controls on mineralisation using a thorough approach of re-surveying, re-cataloguing and re-logging. This model led to an increased degree of confidence and a subsequent upgrade of resource classification, and created several previously unrecognised strong exploration targets. The resulting resource estimates increased the value of the project by 100 per cent.This paper emphasises and highlights the importance of a well-understood geological model on the confidence of a resource estimate and how this may directly impact on the project’s ‘bottom line’.CITATION:Sterk, R and Reid, B, 2014. The Konongo Gold Project, Ghana – an example of how geology makes all the difference to a resource estimate, in Proceedings Ninth International Mining Geology Conference 2014 , pp 467–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

This paper examines the broader implications of recent and ongoing changes in mineral resource managementå and reporting practices and the impact that these might have on mining companies. It is likely that an International Reporting Code will be developed in the near future, based on a number of National codes produced in recent years. However, this is only part of the reporting story, as an International Code brings with it a range of further issues to resolve. For the Code to be effective, there needs to be international recognition and perhaps licensing of Competent Persons and an expanded base of sponsoring professional bodies. Also, in an increasingly global business, shareholders, regulators and other interested parties need to know and understand the general processes involved in resource and reserve estimation and reporting in order to recognise companies that maintain the highest standards. There is a current trend towards greater scrutiny of company performance in a range of areas under the banner of corporate governance, and many changes are happening that will place greater disclosure burdens on all companies in the future. Good corporate governance means management of company assets for the benefit of the stakeholders. For a mining company, there is no greater asset than its mineral resources and reserves and directors are just as responsible for effective management of their mineral resources as they are for financial good practice. The paper looks at the relevance of corporate governance principles to mineral resource management and the changes that this could bring to the way that companies deal with regulators, shareholders, financiers and others. Finally, increased scrutiny and further regulation inevitably means greater effort by the industry and higher costs. Despite this the author believes that there are substantial offsetting benefits to be gained by companies prepared to take the initiative in improving resource management practices and communicating these improvements to shareholders. In order to achieve the benefits however, the industry needs to fully engage in the changes that are taking place û setting its own standards and working with the regulators rather than sitting back and being legislated against. Mineral resource reporting provides a good model of how this process can work and there will be other opportunities in the coming years as the industry seeks to develop best practice in mineral resource management. The author is an employee of Rio Tinto but wishes to point out that the views expressed in this paper are his own and not necessarily those of Rio Tinto.

Jan 1, 2002

By R Barritt, P Scott

Across the globe, it is a common scenario that tailings storage facilities (TSFs) are being decommissioned; however, their subsequent impact on the local environment and landscape can often be overlooked during the mine planning process. In addition, the requirement of a cover system for a facilities closure may not be a priority until the latter stages of the mine/mill operation when potential cover materials may have been utilised elsewhere or, worse, buried. Developing a conceptual design and closure plan for a TSF early in a mining venture is fundamental to its success once operations have ceased. If a cover system is a planned component for rehabilitation of a TSF, it is vital that its design is appropriate to the facility and any local site constraints, such as climate and cover system material availability. It is also strongly recommended that various cover system options are physically trialled at the site by using performance-monitoring instrumentation. Through this process, an informed decision can be made regarding the most appropriate cover system design to meet any regulatory and stakeholder closure objectives and criteria specific to the site in question; however, in order for the cover system’s performance to be determined through on-site trials, it is essential that an appropriate instrumentation design is utilised. Often, little attention is paid to the data that is being obtained, and its importance may only become apparent after several years of monitoring at an expense to the venture. This should not be the case. Many sites have used an appropriate initial planning stage to understand what is required for the successful closure of a TSF, how it can be achieved and how monitoring data can be utilised to prove, or otherwise, that a cover system design will be a success.CITATION:Barritt, R and Scott, P, 2015. Cover system performance monitoring for tailings – are we doing it correctly?, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 283–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Q Yang

This paper describes the design and construction of three 7.2 m span access ramp-tunnels to the three level underground car park of the newly redeveloped Top Ryde City Shopping Centre in northern Sydney. The tunnels were to be excavated without significant impact on the overlying Devlin Street, one of the busiest arterial roads in the Sydney metropolitan area and a major link in the Sydney road network. The interpretation of the geological conditions indicated that the tunnels would be driven in a formation of heavily jointed, extremely weathered to fresh Triassic Ashfield shale with some structural features such as dyke, fault and shear zones identified in the available boreholes logs. Both empirical and numerical methods were used to design the tunnels and to predict the ground surface settlements. The design solution, which was influenced by the relatively small scale nature of the work and the current demands on the tunnel construction market, included presupport, initial support and permanent steel fibre reinforced shotcrete (SFRS) lining. The interactions of the driven portals with cut and cover sections and the proposed deep excavation of the new shopping centre were considered at the design development stage and in the construction phase to ensure the safety of the live road. The tunnels have been successfully constructed and are now operational.

Mar 8, 2011

By D A. Sketchley

The Merlin Zone, a 2008 high-grade Mo-Re discovery, is a part of the Mount Dore Deposit in the Eastern Succession of the Mount Isa Inlier in Queensland, Australia. Hosted by carbonaceous metapelites and phyllites, the Merlin mineralisation comprises molybdenite veins, breccia infillings, stylolitic fracture fillings, and disseminations. Because rhenium is geochemically similar to molybdenum and commonly associated with it, global production of rhenium has been mostly a by-product of molybdenum refining. The high-grade rhenium in the Merlin Zone is an exciting discovery that is expected to become a direct source of rhenium. At the time of discovery, quality assurance (QA) procedures for rhenium were not in place at the Merlin Zone; therefore, they needed to be developed.The Merlin Zone was discovered using reverse circulation drilling, which led to concerns about molybdenite loss due to poor sample recovery. The twinning of the discovery hole with diamond core demonstrated a two-fold increase in molybdenum grade over several tens of metres. Consequently, the resources of the Merlin Zone were defined using assays from diamond drill core.Early analytical work, which was initially done only for molybdenum, comprised geochemical analysis with an aqua regia digestion, which have poor precision and can be biased low. Although initial testing for rhenium used similar procedures to those for molybdenum, a scarcity of commercial rhenium reference materials led to a validation process using neutron activation analyses and different digestions. This resulted in introduction of four-acid digestion assays, development of matrix-matched reference materials, and improvements to the quality of molybdenum and rhenium assays for reporting resources. Coarse and pulp duplicates were used to check for sampling bias and to ensure that levels of precision were adequate for the style of mineralisation and analytical methods. In addition, the direct and consistent geochemical correlation between molybdenum and rhenium provided another method for checking analyses.

Aug 22, 2011

By A N. Parry

In May 2018 Kasbah Resources Limited (“Kasbah”) completed an ore sorting test work program which was a precursor to releasing in July 2018 an updated Definitive Feasibility Study (“DFS”) for the Achmmach Tin Project in Morocco, which it is proposing to develop along with its joint venture partners. The testwork program evaluated ore sorting as a pre-concentration option to achieve early elimination of gangue and the low-grade component of ROM feed, thereby potentially:  Significantly upgrading the head grade of tin to the downstream processing plant.  Significantly reducing the required throughput capacity (and projected capital expenditure) of the downstream processing plant.  Reducing total consumables, power and water requirements in downstream processing.  Increasing the recovery of tin in the gravity and flotation circuit due to the higher feed grade achievable with ore sorting.  Reducing tailings tonnage, tailings cost and environmental footprint.  Using sorter rejects for mine backfill or road base applications. Key aspects of the design of the metallurgical testwork program centred around the need to ensure that samples representative of ROM ore feed (including projected mining dilution) were selected for the ore sorting testwork. The design and implementation of the ore sorting bulk testwork program is described, as well as a summary of the test work results and a discussion of the enhancement of the project economics reported by Kasbah, which led the company to adopt ore sorting as part of the proposed processing circuit in the updated 2018 DFS.

Nov 10, 2020

By K Hobbs

Mining is experiencing a difficult period of low profitability and declining productivity. To achieve sustainability, mining companies are challenged with improving output, quality and safety while decreasing costs. At the same time, organisations are having to manage a workforce in which individuals no longer accept a traditional style of management, employees prefer more flexible employment, and diversity within teams is becoming the expected norm.Increasing organisational diversity has been shown to have a positive impact on performance and therefore sustainability. Gender diversity and equality between working men and women is the area most studied in this regard. Executives are becoming more aware of the correlation between gender diversity and performance with some larger organisations having dedicated resources to increase the number and status of women in their organisations. Despite this, limited improvement in gender equality is apparent globally over the last decade with some industries, including mining, going backwards. So why is this the case and what other strategies are available?In 2015, the United Nations Women National Committee Australia (UN Women NCA) in conjunction with Autopia released a white paper discussing the lack of visible change in gender equality despite the widespread implementation of merit-based personnel management strategies. Using research from around the world and thoughts from influential government, education and business leaders, the paper ‘Rethinking Merit’ debunks the myth of the meritocracy. It provides a number of recommendations for organisations committed to improving their performance and sustainability through diversity, including a variety of real-life company examples, instead of relying solely on merit-based decision-making.This paper takes the recommendations of ‘Rethinking Merit’ and applies them to the mining industry. It shows the relevance that rethinking merit has for the industry and why applying the recommendations can result in an increase in diversity, therefore enabling greater performance and sustainability of mining companies. This paper provides case studies from Aurizon, Iluka Resources and BHP Billiton and, as a guide for managers, a generic diversity strategy designed to be implemented alongside traditional merit-based personnel management techniques.CITATION:Hobbs, K, 2016. Rethinking merit for a sustainable mining industry, in Proceedings International Mine Management Conference, pp 139-154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By A Dal-Corobbo, R Zick

The coal mining industry is now faced with new regulatory requirements that limit the discharge of chlorides into receiving streams. To meet these new regulatory standards for treated mine water, a zero liquid waste approach was developed using advanced treatment technologies. The approach described in this paper will generate clean water for reuse in various energy endeavours or discharge to the environment, with no substantial liquid or solid waste from the treatment process leaving the site.CITATION:Dal-Corobbo, A and Zick, R, 2013. Zero liquid discharge in coal mining operations, in Proceedings Water in Mining 2013 , pp 221-226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By H Yuan, H Tian, Y Zhang, Z Wang, C Wang

Submerged arc welding (SAW) is one of the significant metal-joining processes for manufacturing marine vessels, steel pipes, and offshore structures with high deposition rate and engineering reliability. Welding flux serves several essential functions, including atmospheric shielding, arc stabilisation, bead morphology control and weld metal (WM) refinement. Therefore, from a thermodynamic point of view, the focus for flux design and WM compositional/microstructural modification has been placed to elucidating the transfer pathways and mechanisms of major alloying elements, such as Si, Mn, Ti and O during welding. To this end, a thermodynamic model has been established to predict alloying element contents in the WM. Such functions are enabled by the physicochemical properties of the fluxes, which are inherently rooted in the nature of the fluxes. A unique yet systematical investigation, including physicochemical property changes and structural evolution behaviours, has been conducted over the wide range of fluxes applied to actual welding of EH36 shipbuilding steels. Combined with spectroscopic methods, structural behaviours of network formers such as SiO2, Al2O3 and TiO2 and network modifiers such as MgO, MnO and CaO have been illustrated. Viscosity and ionic conductivity have been found to be positively associated with the degree of polymerisation.

Aug 21, 2024