Search Documents

By Rashad MZ

The evaluation of ore deposits consumes much effort, cost and time, hence research work must aim to minimize these inputs with no loss of accuracy. The present study is devoted to assess the optimum conditions and methods of calculations which give minimum costs of ore exploration. An area of (a x a) where "a" is the zone of influence of the semi-variogram, i.e. (2800 x 2800 square metres) located within the Abu Tartur plateau is the subject of the intensive study. The distances between boreholes are varied ie. a/4, a/6, a/8 and a/ 10 respectively. The average ore grade (G), thickness (t) and relative ore reserves (tG) are calculated by four methods. The results indicate that at a distance equal to a/5, the inverse distance squared method gives the best results. These parameters save about 50 percent of the cost of exploration with a map accuracy greater than 90 Percent.

Jan 1, 1987

By C D. McCullough, M Gerner

Rarely do opportunities arise allowing closure of a mine site to be planned as a key beneficial land use asset within a new urban growth area; particularly so well prior to cessation of mining.Pit lakes are common mine closure legacies for many open cut mines and may form in open cut mine voids extending below the water table upon closure. Mine closure guidelines increasingly require post-mining land uses of equivalent capacity to premining conditions and that minimise long-term post-mining liabilities and maximise benefits to stakeholders and the environment. However, risks presented by pit lakes are regularly neglected in closure planning or are not able to be addressed to allow beneficial end use of the lake or surrounding land.This paper describes strategic planning initiated by quarry owners ten years before mining ceases. In liaison with the planning agencies, the planned closure of a large 100-year-old limestone quarry pit will form a lake on mine completion, with a well-considered beneficial end use in an urban setting in mind. The quarry pit and adjoining land at Batesford South about the edge of the City of Greater Geelong, Victoria, Australia. Geelong is experiencing growth pressures that necessitate development of a new growth area from about 2025.A multidisciplinary expert team assessed the constraints, opportunities and feasibility of rehabilitating the quarry and pit lake and developing the surrounding land as Geelong’s next urban growth area.The concept is exciting and demonstrates that a former mine site could become a valued home to about 40 000–45 000 people. About 30 per cent of the land will also be developed as an ecological riverine corridor including the pit lake that will become a regionally iconic lake as the centrepiece of an urban development.Our paper outlines technical challenges and how these can be met to achieve closure and beneficial use that meets the social, economic and environmental expectations of contemporary urban planning.CITATION:Gerner, M and McCullough, C?D, 2014. Planning for the future – development of beneficial end use from a quarry pit lake, Victoria, Australia, in Proceedings Life-of-Mine 2014 , pp 99–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Haukka M. T

A new low-dilution fusion method which has been successfully used for accurate determination of the major oxide components of silicate rocks, is applicable to rapid, accurate determination of trace or minor eiements in mineral exploration samples. Limit of detection is in many cases less than 5 ppm. Either rapid, approximate measurement and calculation methods (suitable for geochemical exploration), or more accurate methods (applicable to orebody evaluation studies) may be used.Rapid methods are described for nickel in rocks and sulphides containing 10 ppm to >2 per cent Ni, and for gallium. The rarely-determined element gallium is an example of a constituent which may be easily investigatedby XRF using the LiB02 fusion disc, which is a permanent, easily-stored analytical sample available for later rapid or accurate analyses. The method is applicable to over 30 elements at levels encountered in mineral exploration.

Jan 1, 1978

Under the Town and Country Planning Act 1977 the Ministry of Works and Development has a responsibility for providing information to local and regional planning authorities on public works and matters of national development and importance, for the exercise of their responsibilities under this Act. One such matter which has recently become a source of concern is the development of South Island lignite. In 1979 the Ministry of' Energy produced a position statement outlining a programme of' research leading to the possible extraction of lignite in Southland or Central Otago for conversion into about 50 per cent of New Zealand's liquid fuel requirements by 1995. Understandably this possibility has caused considerable concern at the local level, expressed particularly by bodies such as Federated Farmers and the local authorities. In the absence of any factual knowledge short of mere conjecture been able to recommend to local authorities is that they limit their planning period to ten years. After this time more information regarding the size, nature, location and certainty of the proposal will permit a more accurate assessment of the implications of the York. While on holiday earlier this year I took the opportunity to visit opencast mining areas in Germany and England to gain an appreciation of the scale of impacts involved and discuss with those concerned the procedures used in planning for such operations. What follows is a brief description of these operations, a comparison with the likely development in this country and the extraction of what may be some relevant principles of' operation for the planning of an environmentally acceptable project. Please note that the views expressed in this paper are mine alone and are not necessarily those of the Ministry of Works and Development.

Jan 1, 1981

In November, 1967, a four strand curved mould continuous casting machine coupled with a 50 ton basic oxygen furnace began producing billets for the rod mill and new merchant mill at the Newcastle Steelworks. To date over 500,000 tons of carbon and alloy steels have been cast at the rate of 20,000 tons per month, the major part for the wire industry. Many alterations have been made to the plant to simplify the process, improve quality and increase production. Casting parameters have been developed for each different type of steel. The quality of the final product has been influenced most by casting temperature, secondary cooling and casting speed. All these factors have been controlled and good results are reproduced. More exacting requirements of liquid steel quality have brought about the use of higher lime/silica ratio slags during steelmaking to control phosphorus revers- ions and standard ladle additions of manganese suicide and ferro aluminium for more effective deoxidation.

Jan 1, 1972

By Kershaw M. G, Maughan R. C A

A process for eliminating nickel from electrolytic zinc plant solutions by precipita- tion with dimethylglyoxime (DMG) was developed to enable the Electrolytic Zinc Company of Australasia Limited (EZ) to treat nickel-bearing zinc dust precipitates. These precipitates are leached to recover their Cd and Zn content. The final Zn bearing solutions contain relatively high Ni concentra- tions (20-100 mg/1) and are treated with DMG and then neutralized to pH 4.6-4.8. The pre- cipitate is filtered off and the solution returned to circuit. DMG consumption is about 200% of theo- retical requirement, and Ni removal is 80% complete overall.

Jan 1, 1977

Exploration by Cyprus Minerals Australia Company (formerly Amoco Minerals) has successfully outlined significant Au-(Cu) mineralisation at Starra, 150 kilometres south-east of Mt. Isa. Mineralisation is stratabound and localized in deformed and metamorphosed ironstones (B.I.F?) and iron-oxide bearing schists of the mid-Proterozoic Staveley Formation. Over 90% of the presently outlined potential ore occurs in 4 discrete zones within a strike length of 3.5 kilometres. The inferred geological resource in these zones is approximately 6 million tonnes grading 5 grams per tonne gold and 2% copper. Roughly half of this is open-pittable, but more rigidly applied mining criteria will probably reduce the exploitable tonnage. Detailed infill drilling is in progress and a pre-feasibility study has commenced. The joint venture partners, Cyprus Minerals (75%) and Elders Resources (25%) expect to make a development decision by the end of this year.

Jan 1, 1986

By D A. Collins

The floatability methodology developed by the AMIRA P9 project through research contributions by the Julius Kruttschnitt Minerals Research Centre (JKMRC, Brisbane, Australia), University of Cape Town (UCT, Cape Town, South Africa) and McGill University (Montreal, Canada) has been successfully commercialised through JKTech. The methodology involves detailed flotation plant campaigns which require large quantities of data to fit models that can be used in JKSimFloat (a steady state simulator for the flotation process). The methodology to date, although widely accepted as the best flotation optimisation technology available, is limited to existing circuit optimisation and requires full plant or pilot plant data to calibrate new models. The floatability of new ore types cannot be characterised using this method unless a pilot campaign is undertaken. After reviewing a large database of existing industrial floatability data, a new methodology is proposed that involves a laboratory based flotation test procedure and review of the floatability database to characterise the floatability of new ores. The full methodology is labelled the floatability index test procedure (JKFIT). This paper outlines the JKFIT procedure and the results of applying this methodology to pilot plant data from a copper ore. JKFIT was applied to two different feed sizes (namely a P80 of 180 microns and 212 microns) of this copper ore. The results of applying JKFIT to this case showed that the metallurgical response (in terms of grade and recovery) from the full pilot plant survey data could be predicted well. Further validation of this methodology was conducted on a separate copper ore. The results from this validation also showed that the JKFIT test was able to be used to predict the full plant performance. The JKFIT test has the potential to become the 'drop weight' test of flotation which will improve the confidence in plant design flow sheet layouts, allow full orebody characterisation and prediction of key grades and recoveries before the ore enters the plant, and will provide an improved methodology for chemistry impact analysis on different ores.

Jan 1, 2008

By A Hekmat, M Fuentes, F Armijo, R Castro, F Rodriguez

Interpreting the behaviour of granular material and simulating the gravity flow are complex processes in cave mining methods. In this paper, a new Cellular Automata based code – FlowSim – is used as a flexible tool to simulate the gravity flow and subsidence zone in block caving mines. The simulation results of the gravity flow model in a real scaled mine as well as a scaled physical model are presented in this study. In this research, FlowSim was first calibrated at a mine, based on the information obtained from smart markers. These markers were located in five points of the second block of the Esmeralda sector, at the El Teniente copper mine, Codelco, Chile. The calibration was performed with the objective of reducing the discrepancy between the extraction zone defined by markers in the mine and FlowSim outputs. Regarding the mine data, FlowSim was calibrated with the minimum error of ten per cent between real and simulated results. Then, the calibrated FlowSim model was used to simulate the flow behaviour of a scaled physical model. This model was constructed in the Block Caving Laboratory of the University of Chile to scale down the same block of the Esmeralda sector with the scale of 1:200. The FlowSim outputs show that this software enables the simulation of the gravity flow of the scaled model with less than five per cent discrepancy in grade and dilution entry to the drawpoints. According to the obtained results, this paper recommends FlowSim as an appropriate tool which can improve the design of production level in block caving and can enhance the prediction of the subsidence zone and dilution entry.CITATION:Castro, R, Hekmat, A, Fuentes, M, Armijo, F and Rodriguez, F, 2016. FlowSim – a versatile flow simulation tool to quantify extraction and design alternatives for block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 645–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By B Tutmez

Determination of stress-strain behaviour of rocks plays a crucial role in understanding the response of rocks during loading. However, it is a tedious, expensive and a time-consuming process to obtain such characteristics both in the laboratory and in situ. On the other hand, non-destructive testing methods such as ultrasonic velocities can produce a reliable and fast solution to indentify state of strain and stress in rocks. The present paper aims to provide insight into the relations amongst ultrasonic wave velocities, amplitudes and deformability properties of porous siltstone under compressive loading. For this purpose, pulse (vP) and shear wave velocities (vS) along with amplitudes (AP - AS), and applied loads with resultant strain were measured simultaneously so that response of siltstone to compression can be evaluated. In addition, initial vP and vS were recorded at the beginning of each test to calculate dynamic elastic properties of the specimens. This provided a comparison between static and dynamic elasticity properties of siltstone. Crack damage associated with the onset of dilation was also investigated. The results showed that there is a non-linear logarithmic relation between velocities and stress-strain level for siltstones.

Sep 26, 2011

By N Takamatsu

The environments surrounding the iron and steel industry have changed greatly in recent years. Reported in this paper are the technologies adopted by the Japanese iron and steel industry to fititself to change in global steel demands, degradation of iron ore and coal, prolonging service life of the facilities and requirements of energy saving. In addition, innovative technologies for CO2 emission control in iron making processes are also discussed.

Jul 11, 2011

The nature of the specialty glass and ceramic business magnifies the dependency of the ultimate product on the unique properties of their raw materials used to make them. This dependency has implications in the management of risk in the supply process which requires a special procurement organization and program commitment to be successful. The Coming system of managing critical materials and factors in development of alternate new suppliers and products is discussed.

Jan 1, 1989

The Professional Standards Act responds to the growing problem of professional liability by introducing a mechanism whereby professional associations can have schemes approved. Those schemes include a cap on liability; a requirement for compulsory insurance; the development of risk management strategies; and the establishment of a complaints and disciplinary system. The Act is also designed to support and develop the concept of self-regulation by the members of occupational associations who provide services to the community by providing them with those tools. It implicitly accepts that self-regulation is preferable to statutory regulation and that self-regulation serves the interest of the community and of the providers of services. The Act arose from a review of professional liability commenced in 1988. The Attorney General's Department produced an Issues Paper, released in September 1989, which outlined in detail the extent of the problem. This was widely circulated and an extensive number of comment were received.

Jan 1, 1995

By A Purton, C Taylor, E Conroy

The spatial modelling of geometallurgical domains is an important step in the characterisation of an ore deposit allowing for the quantification of various rock types, their differing rock properties and the overall value of a project. The traditional approach to modelling such features is through the use of deterministic models, where a single estimate of the extents and structure of the ore deposit is mapped out by geologists based on available data and their interpretation of the geological processes. Any uncertainty in the layout of different domains is not accounted for and heterogeneities of chemical and physical properties of the orebody are likely underestimated. Spatial machine learning techniques can be used to derive geometallurgical categories, or classes, from multiscale, multiresolution and high dimensional measured rock properties. Subsequently, geostatistical simulations of these classes can be applied to obtain multiple equiprobable realisations that define the layout of the geometallurgical classes at unknown locations between boreholes, or domains. In-turn these realisations can be used quantify the uncertainties in the location of boundaries between different domains. The development of a workflow for defining geometallurgical domains and later geostatistically simulating them across the Orebody H; a complex stratabound Bedded Iron Ore deposit located in Western Australia’s Pilbara region is demonstrated. This could be used to identify zones of high uncertainty where collection of additional data might help mitigate or minimise risks and in turn improve forecast production performances.

Mar 22, 2022

By H Ishikawa, S Palaniandy

The gravity-induced stirred mill such as the TowerMill is an energy-efficient grinding solution used in secondary, tertiary, and regrinding duties in the mineral processing concentrator. The interest in this technology is emerging, with more than 300 mills installed globally in various grinding duties and commodities for the last 30 years. Although the technology is matured, there are still opportunities for improvement and the development of new knowledge to improve its circuit energy efficiency and reduce water consumption. Recent studies show that a combination of stress intensity, ore hardness, slurry density, and mill feed configuration can be used to evaluate the performance of the grinding circuit. A recent pilot-scale TowerMill test work at various stress intensities shows that a lower operating work index and size-specific energy were achieved at higher agitator tip speed and using medium size grinding media. These outcomes were confirmed through several site trials. A smaller 17 mm grinding media has reduced the operating work index and size-specific energy by 18 per cent and 11 per cent, respectively, compared to the 20 mm in a magnetite concentrator. Moreover, the conversion from top feed to bottom feed configuration has reduced the operating work index and size-specific energy by 13 per cent and 37 per cent, respectively. The circulating load was reduced by 34–38 per cent, leading to a reduction in the dilution water consumption in the hydrocyclone feed sump by 20 per cent. A variable frequency drive offers flexibility to change the stress intensities on the TowerMill, where a 35 per cent reduction in specific energy was achieved when the ore became soft. This paper explores the potential design and operating strategies that can be implemented to enhance the energy efficiency, reduce water consumption and reduce CO2 emissions in the circuit and finally evaluate its impact on the total cost of ownership.

Aug 24, 2022

By A Brzovic, E Córdova

In an underground mine, different mining activities such as undercutting and cave progression generate redistribution in the present in situ stress field, and these changes are represented in the rock mass through induced seismicity.In order to study and analyse the induced seismicity generated in El Teniente, a block model was developed to account for the dissipated seismic energy through different areas of the mine from 1992 to 2015. More than 2.1 million seismic events were unified and classified in 3D in order to be used for the interpolations. The resultant model variables account for the accumulated energy releases in a monthly time resolution, and provide the ability to intersect different 3D entities with the stored information in the blocks, and estimate the energy evolution inside these entities.The generated model was used to analyse the geotechnical variables that determine the seismic response for the rock mass in the mine, such as geometry and direction of advance of the undercut fronts, lithological domains, and to study the ‘work’ the rock mass needed to go through in order to generate caving in areas with different stress settings.A specific area of the mine under high-stress conditions was analysed by studying the seismic energy associated with two subsidence caves interacting around the project, the modelled lithology. Using the same approach two adjacent projects are analysed to understand the released energy from the rock mass based on different stress and geotechnical settings for each project.CITATION:Córdova, E, Brzovic, A and González, R, 2016. Analysis of progressive seismicity and its correlation with geotechnical variables at the El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 835–844 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Grady B. V, Ault A. R, Newman O. M G, Fraser R. J, Malcolm J. McPhersqn

In all electrolytic zinc plants cadmium is removed as an impurity prior to the zinc electrowinning stage of the process. Cadmium metal is the favoured form of this by-product and most plants use an electrolytic route for its production. The formation of dendrites in cadmium electrowinning processes is the major limitation to deposition rates. There is an economic incentive, therefore, to better understand the factors affecting their growth. A technique that has been used by others to examine fundamental aspects of dendrite growth has been applied to industrial strength electrolytes. It involves potentiostatic deposition in a cell containing the electrolyte of interest. The variation in the current with time at a given overpotential allows the determination of the dendritic growth induction time. A method was developed (the Locus method) from the investigation of a set of such potentiostatic curves, obtained over a range of applied overpotentials, that appears to give a measure of electrolyte quality with respect to dendritic growth in galvanostatic deposition. The Locus technique predicts that zinc at industrial concentrations in cadmium electrolytes should have a significant effect on morphology and that deterioration of morphology will occur as the zinc concentration in the electrolyte is increased. This effect is consistent with literature prediction and was shown to relate to a reduction of the diffusion limiting current density. Magnafloc R333 is used as an additive at Pasminco Metals-EZ to control the morphology of cadmium deposits and the Locus method was successful in predicting its dendrite inhibiting properties. A possible mechanism is discussed. This work has opened avenues for future research with respect to a technique that may have an industrial application in electrolyte characterisation and has pointed to a direction in which better understanding of galvanostatic dendritic growth may be found.

Jan 1, 1993

By White B

A novel approach is suggested for the solution of planning and development problems in the coal, mining industry. The formation of coal measures depends to a significant extent on sequential geological processes and events which are probably best defined in a "system of processes and responses." The great number of variables in such a system is a characteristic feature of geological environments. Research work over the past two decades, in particular, has successfully established analytical procedures for the identification and definition of relevant and irrelevant variables for mining developments in specific geological situations. Such situations are typifiable within the regional geological setting of coal deposits. Scale gaps can be bridged by reliance on common symmetrical attributes and pervasive geometric features. Depositional processes and their resulting attributes are responsible for the development of mechanically significant rockmass "defects" and anisotropies; such features have to be identified and assessed for the selection of colliery design criteria. It is suggested that the procedural frame- work of systems engineering analysis is a most appropriate tool for the assessment of those geological features that can influence the mechanical behaviour of the "floor-seam-roof" system in "high technology" mining operations of the future. It is anticipated that the overall emphasis of future mining systems will be toward the use of larger scale more highly productive methods and machines, with higher capital outlay but

Jan 1, 1987

A modified liquation technique was developed for recovering tin from tinhouse scruff metal or hardhead containing about 10 per cent iron and 15 per cent occluded flux, palm oil, and moisture. This was effectedby heating the scruff metal to 950°C followed by rapid cooling to suppress the formation of FeSn2 and FeSn, and then subjecting it to the ordinary liquation and drossing processes of refining. By this method it was possible to recover about 83 per cent of the original tin content and, with subsequent smelting of the irony drosses, an overall recovery of 92 per cent was obtained.

Jan 1, 1969

Dynamic hydrothermal modeling is a tool that can aid in studying problems associated with hydrothermal ore deposits and can help increase our understanding of the spatial distribution of ore within hydrothermal systems. Models are constructed by a sequence of steps involving development of a conceptual model, followed by its mathematical description in terms of governing equation with accompanying initial and boundary conditions. This equation is then solved either analytically or numerically. The four model types ò that fully describe a hydrothermal 'system are those for fluid flow, heat and ore solute transport, and deformation. At Renison, models have been used to help understand two major exploration problems. These are the controls on ore localisation in dolomite horizons and feeder faults respectively. The types of models used ò have simulated the distribution of all mineral zones, pyrrhotite, and temperature in the dolomites. This has allowed evaluation of the effects on ore localisation by physical and chemical heterogeneities within the dolomite host rocks, and allowed estimation of potential controls in different physical and chemical environments.

Jan 1, 1987