Search Documents

By J Watson, C Zhang, I Canbulat, C Wei

Coal burst is defined as a dynamic release of energy within the rock or coal mass in underground coalmines that causes violent rock or coal ejection in the vicinity of mine excavations. It poses one of the highest safety and productivity risks in the mining industry as coal bursts have the potential to cause multiple fatalities. As Australian coalmines go deeper, the likelihood of coal burst increases. Thus, it is critical to assess the ground support requirements in coal burst-prone conditions. A previous study conducted by the authors (Wei et al, 2022) reviewed the support capacities of a wide range of ground support elements in laboratory tests. This study aims to examine the role and effects of the ground support elements and systems for Australian underground coalmines to minimise the damage caused by catastrophic dynamic failures (ie coal and rock burst) and enhance the safety of mine workers.

Nov 29, 2022

In order to meet the increasing demand for coal for their Newcastle Steel Works, the Broken Hill Pty. Co. Ltd., on June 5, 1937, approved of a scheme to sink a tunnel to the Victoria Seam at their Burwood Colliery. This seam was virgin at this locality and lay nominally horizontal at a depth of 320ft. vertical from the surface.For the purpose of despatch of the coal produced it was decided that the tunnel be equipped with a rubber belt conveyor system.This was a comparatively new departure in Australia, and, indeed, was one of the first installations of its kind in the world, designed to raise coal from considerable depth by this means. Later the tunnel was extended to the Borehole Seam, which lay nominally horizontal at a vertical depth of 600ft. from the surface. The whole installation is the subject of this paper.In planning a project of this kind, consideration had to be given to the following:-1. Location of tunnel with regard to existing surface railway sidings and shafts.2. Ultimate tonnage required.3. Width and construction of belt.4. Speed of belt.5. Inclination of belts.6. Number of belts and design of equipment.7. Cross-sectional area of tunnel.8. Inclination of tunnel.9. Surface drainage.10. Type of equipment for drifting the tunnel.11. Method of ventilating the tunnel during sinking.After the general layout and design of the scheme had been prepared it was decided that tunnel drifting would begin immediately and that the belt installation, together with the feeder plant, would be detailed and manufactured by the time the drift...

Jan 1, 1947

Industrial minerals by definition are minerals used as part of an industrial process and usually are one of a number of components, eg finely ground Limestone is an extender in the manufacture of paint. They are normally non-metallic and non-fuel, but like all generalisations there are a number of exceptions. Take rutile û a source of titanium, a metal and also the raw material in the manufacture of titanium dioxide pigment. Industrial minerals under this general definition include construction and agricultural minerals. They are included in the same grouping, principally because their sources are similar and in many cases the raw material, example limestone, can be multi-functional. Calcium carbonate raw materials such as limestone, are used in a wide range of applications from industry as an inert filler, to agriculture as a 'lime' source and to construction and as an important component in the manufacture of cement. As far as this paper is concerned I will avoid discussing the agricultural or construction applications, including burnt lime production.

Jan 1, 1985

By Schonert K

The throughput of a HP-roller mill is determined by the acceleration of the feed material within acceleration zone and introduction into the compression zone. Both processes depend on the internal friction and the friction of the material on the roller surface which is influenced by the surface structure and adhering of material. The particle motion in the acceleration zone has been investigated with high speed videos showing the effect of the centrifugal force and the slip on the roller surface. The throughput is discussed in the term of the specific throughput which can be approximated by a linear function characterised by the throughput number and the throughput elasticity. The throughput number is a helpful measure for investigating the influence of the feed material and the surface structure. The experimental results give some guidance for chosing an optimum corrugation profile.

Jan 1, 1993

Cores of pre-Tertiary basement from ten oil exploration wells are related petrologically to the "axial", "marginal" and "shelf" facies of the New Zealand Geosyncline.A NW. Nelson-type basement is inferred beneath peninsular Taranaki and the western continental shelf. The terms Taranaki Basin and Wanganui Basin are re-defined and the terms North Wanganui Basin, South Wanganui Basin, Pipiriki High, Taranaki Fault, and Turakina Fault are proposed. Major faults are interpreted as of mainly transcurrent type and appear to form the western part of a splay at the northern end of the Alpine Fault. Evidence for a major Cook Strait Fault is reviewed.

Jan 1, 1967

YOUR Excellency, Fellow Members of the Australasian Institute Of Mining Engineers and Gentlemen:- Nearly a decade has passed, since our Institute first met in New Zealand. May I, at the very outset of this second gathering, congratulate the Institute on the great progress that has been made in the interval. At the first meeting in New Zealand in the year 1903, I understand that less than 20 persons were present, and now in the large concourse before me I believe there are not fewer than 140 persons, while if every member of the Institute to-day where here there would be over 500 which is a great change from a membership of only 250 in 1903. I feel deeply appreciative of the honour you have conferred upon me by electing me your President for the year 1911. In return for the compliment, may I ask you to believe that I shall do everything in my power to further the interests of the Institute throughout the coming year.It is a great regret to me to realise that soon my work in New Zealand will be over. However, I trust that the new...

Jan 1, 1911

By L Reynolds

The portable infrared mineral analyser (PIMA) was trialled to determine the extent and intensity of any hydrothermal alteration halo associated with gold mineralisation in the Hyde-Macraes Shear Zone (HMSZ) of the Otago Schist.   Twelve diamond drillholes through the HMSZ were analysed with the PIMA at a sample spacing of 1 m. The drillholes were selected on two traverses along the line of strike and down-dip of the mineralisation in and around Panel 2 of the Frasers underground development.   The study showed that the Hangingwall shear of the HMSZ has a more distinctive infrared signature in intersections with high grades. The Hangingwall shear in these drill holes is defined by a shift in the wavelength of the Al-OH absorption feature from ~2220 nm to <2210 nm. This shift is attributed to a change in the mineralogy from phengite to muscovite. Overprinting this trend in some of the drillholes is the presence of the 2210 nm Al-OH absorption feature, ascribed to kaolinite. Kaolinite also tends to be present in numerous other regions of the schist above the Hangingwall shear associated with steeply dipping faults and foliation parallel joints. In drill holes with low grades the Hangingwall shear does not exhibit any obvious infrared signature.   At the scale of study, the PIMA does not provide evidence for an alteration halo associated with hydrothermal mineralisation above the Hangingwall shear. Possible tectonic movement may have displaced any alteration halo that once existed, away from the zone of mineralisation. For this reason, PIMA apparently cannot be used for predicting the location of the Hangingwall shear during exploration drilling. However, the study did show that the PIMA could define the Hangingwall shear when the rocks were sufficiently altered and mineralised.

Jan 1, 2007

By A Crosky, S Saydam, H Chen, H L. Ramandi

Cable bolts and rock bolts are used as primary and secondary anchoring systems in many underground mines. Reports on the premature failure of cable bolts and rock bolts due to stress corrosion cracking (SCC) in underground coalmines have been increasing in the past two decades. The previous studies found that the SCC in both rock bolts and cable bolts occur as a consequence of atomic hydrogen diffusion into the material, which is known as hydrogen-induced stress corrosion cracking, HISCC (Craig et al, 2016; Wu et al, 2018b). While research to understand the process of SCC occurrence in underground mines is still required, finding a prevention solution to protect the bolts from HISCC is crucial. In this study, we analyse a variety of commercially available coatings for steel corrosion prevention, including barrier coating (ie epoxy, polyester TGIC) and sacrificial coating (hot-dip galvanising). We test the coating on coupons manufactured from rock bolts and cable bolts used in the coal mining industry.

Nov 29, 2022

Electroosmotic Dewatering and Consolidation of Mineral Waste Tailings

Sep 13, 2010

By Barnett DW

Financial risk analysis provides the tools to examine the uncertainty of capital decisions in new mining ventures. This paper explores the methodology by which financial risks can be studied and quantified. The most commonly used risk evaluation methods, such as sensitivity analysis and discount rate adjustment, are presented as an introduction to a more comprehensive discussion of stochastic methods of discounted cash flow analysis using Monte Carlo sampling. The discussion is illustrated with examples of a stochastic discounted cash flow. The advantages of Monte Carlo sampling in risk analysis are discussed together with its problems, particularly those originating from the correlation amongst the variables that determine the economic output of a mining venture, and the difficulties created by insufficient data, imperfect knowledge and complexity. The paper also surveys the most commonly used software used in risk analysis.

Jan 1, 1994

Traditional vat leaching has been done on a batch basis, which involves loading the vats, leaching, drainage, washing, draining again, and unloading. As a result of these many steps and the attendent cost of labor, vat leaching is generally not an economic proposition. Also, like heap leaching, there is a tendency for channeling to occur within the bed, whether the leach solution flow is by percolation upwards or downwards. No doubt experimenters over the decades have been enticed by the idea of fluidization induced by upward flow through the ore bed. If the bed could be fluidized, then a continuous flow of material could be set up, dispensing with the high cost of loading and unloading the vat. A quick calculation of solution flow requirements, however, soon reveals that the volume of constant liquid movement necessary to sustain fluidization is prohibitive from a power and cost standpoint. The premise of the Mackie Vat Leaching Jig (MVLT) concept was that the large volume of liquid flow required for fluidization could be achieved instantaneously, and that during this small element of time, the solids would flow under the influence of the hydraulic gradient in the vat. If this procedure could be repeated in a cyclic manner, then a steady-state condition could be set up. Experiments in the laboratory demonstrated that solids flow could be achieved in this manner.

Jan 1, 1991

The use of rubber-tyred equipment in a decline mining system requires that roadways be kept free of running water. At Renison this is achieved by the use of stage pumping or gravitating to a major pump station and pumping from there directly to the surface. The frequent use of pick-up lines and pump boxes in the decline system provides a method of water control and reduces the amount of slimes in pump lines. The Bassett Fault structure, which lies on the hangingwall of the mine is the major source of ground water. This is encountered in diamond drill holes and exploration develop- ment. Dewatering of this structure is possible by controlling the flow from selected holes. Future pumping requirements may be predicted by analysing changes in the level of the water table and by calculating dewatering rates required to maintain ore reserves available for production.

Jan 1, 1977

By Neill B. K, Fander H. W, Wong K, Dunlop G, O&apos

Commercial interest in refractory gold is increasing rapidly. This trend is supported by the work patterns of Amdel, where, apartfrom routine process- ing of free-milling and refractory ores, the majority of testing now includes biological and pressure oxidation studies to enhance gold recoveries. Central Mineralogical Services have examined, among other ores, an apparently unique type of refractory coating. A summary is given of experience at Optimet Laboratories, Pty., Limited. Research into nitric acid pre-oxidation, underway at the South Australian Institute of Technology since 1987, has shown significant improvements in gold recoveries, and in some cases, large reductions in reagent consump- tions. Three final-year student research projects were undertaken in 1990, jointly between the University of Adelaide and the S.A. Institute of Tech- nology. These projects involved biological pre-oxidation, pressure leaching, and Scanning Electron Microscope examination of refractory ores, and the resultant pre-oxidation and cyanidation products.

Jan 1, 1991

By Hatherly P, Dunn P

There are- several in-seam coal research projects currently under investigation by the Cooperative Research Centre for Mining Technology and Equipment (CMTE). The overall aim of the projects is to produce new technologies to enhance safety and the efficiency of in-seam gas drainage drilling. Results from high pressure waterjet rotary drilling trials indicate that by applying high pressure water to a rotary drill bit, the hole can be drilled to follow the planned trajectory very closely. Steerable drill bits for drilling long holes (>1 km) have been produced and trialed. A flexible high speed drilling system provides a capacity for rapid in-seam drilling, particularly suited to cross panel drainage. Geophysical tools are being developed to provide a geological steering capability and a better understanding of potential gas outbursts zones.

Jan 1, 1998

By Okura T, Hino J

Coal utilization for copper flash smelting in Japan was initiated due to the sudden upheaval in the price of oil in the last ten years. A major portion of the heavy fuel oil has already been replaced by coal resulting in a corresponding decrease in energy costs. In addition to energy cost savings, an interesting metallurgical phenomenon was observed in flash smelting operations. Unlike oil combustion, coal is not burned completely in the shaft. A considerable fraction of coal particles remain on the surface of slag and are burned at the settler. Chemical investigation has shown that oxygen potentials at the settler have consequently decreased, bringing the slag and matte phases into reducing conditions, thus oxidation and reduction can coexist in one flash smelting unit. As a result, a decrease in magnetite and copper contents in the slag, elimination of furnace hearth build-up and dissolution of intermediate layer between matte and slag have been observed. In general, these led to improvements of furnace operations. However, thermodynamic investigations have shown that some minor elements such as As, Sb, Bi and Pb concentrate from slag to matte. Results evaluated on the basis of thermodynamic data relatively agree with practical observa- tions. Consequently, for coal utilization in flash smelting operations it will be necessary to control oxygen potentials from the stand- points of copper loss in slag and minor element Distributions.

Jan 1, 1987

By Teague JK, Read HW

The relationship between the maceral composition of coal and the strength of the coke produced from that coal has received a great deal of attention in recent years. Studies using two Bulli Seam coals, and blends of Bulli and Wongawilli Seam coals, from the Illawarra Measures of the Southern Coalfield of New South Wales were carried out. The optimum range of vitrinite was found to lie between 45% and 60% (mineral matter free). Above and below this vitrinite range coke strength deteriorated. I Coke strength indices increased with rank and the optimum vitrinite content increased with an increase in rank. These changes will require confirmation as trends by testing a third level of rank. It was noted that vitrinite content decreased with an increase in the specific gravity of separation of the coal. . T Use of- petrographic analyses will increase confidence in choosing coals for coking, provided the coals are well known. Such analyses offer the possibility of greater flexibility in coal purchases and the possibility of producing a marketable blend from coals, which have limited market potential. Critical base coals for blends can be conserved. Significantly more work is required before coal reserves can be utilised to optimum advantage. This work would require extension of-the studies discussed in this paper and, in particular, the testing of a wider range of rank.

Jan 1, 1970

The majority of coke in Australia is made in by-product slot ovens at steelworks in Port Kembla, Newcastle and Whyalla. Most of the coals for these plants come from New South Wales but a regular proportion of Queensland coals may be introduced. The plants and the coals are reviewed in the paper.

Jan 1, 1975

The bureaucracy in Victoria has worked against exploration and mining development. There is no doubt that the new Mineral Resources development Act has simplified matters on the mining side of the system. However, WMC's Bendigo and Deep Lead experiences demonstrate that other parts of the bureaucracy can cause serious delays. The mining industry continues to view the approval process causal of excessive costs and delays compared with other States (and countries) and prohibitive to investment in Victoria.

Jan 1, 1992

This paper explores options worthy of consideration in the management of S02 produced from the gold roasting operations at Kalgoorlie. Some of the options have relevance to other sources of SO2 in the region, eminating from nickel smelting operations. The paper considers the following options: 1. Capture of SO2 within the roaster where sulphur-containing reaction products are mixed with the calcine. 2. Processes in which the sulphur-containing products are bled separately from the stack for further treatment or for dumping as a waste. These include: Seawater-based scrubbing of SO2; Sulphuric acid manufacture as a feedstock for fertiliser production or for leaching of bauxite; its use as Caro's acid: and the production of value-added sulphur-containing reagents eg liquid S02 and sulphonic acid.

Jan 1, 1992

By Boyes B. A, Haydon D. J

The Paddington project is a gold mining and processing operation located 35 km north of Kalgoorlie in the Eastern Goldfields region of Western Australia (Figure 1). The project, which is operated by Pancontinental Goldmining Areas Pty Ltd, treats 1.25 Mtpa of oxidised gold ore, derived mainly from open cuts adjacent to the plant, with minor tonnages from other pits in the region treated on a custom-milling basis. Gold is recovered using a conventional CIL process. The process raw water supply of 3 500 kUd is derived from the local groundwater system. Average salinity of the raw water is around 90 000 - 100 000 mg/L total dissolved solids. A small portion of the raw water is passed through a vacuum distillation desalination plant to produce the project's 200 kUd requirement for high quality water for potable use and gold recovery.

Jan 1, 1988