Search Documents

By M Ujihira, M Komazaki, K Higuchi, D F

A diesel engine with a misfiring cylinder is likely to break down in a short time when the engine is used without maintenance. The authors have developed a method of detecting the occurrence of cylinder misfiring and specifying the misfiring cylinder by using wavelet analysis and statistical analysis on the root mean square (r.m.s.) values of two kinds of acceleration waveforms. This detection method is considered superior to traditional methods, which require several accelerometers, especially in terms of simplicity. Since the development of the method, research has been conducted on semi-automatic processing of measured signals and signal transmission from the worksite to a remote office. Field tests confirmed that 1 + 105 points of dynamic data could be transmitted through the mobile multimedia network within 15 minutes, and the time for signal processing was within 15 minutes. Final determination on the condition of a diesel engine in heavy machinery could be achieved within 30 minutes. Shortened processing time is expected by improvement of the processing software.

Jan 1, 2003

My early experience with the coal industry was in the latter half of the 1970s, where attention to only ones own æaccidentsÆ and concentration on behaviour controls were impeding the introduction of effective engineering controls such as ROPS, FOPS, roof support and residual current devices. Lack of the broad picture of personal damage and of relevant veridical (true saying) knowledge and data had to be overcome to achieve progress in reducing fatalities. Thirty years on, it is again necessary to take stock. How good is our knowledge, our data, our information on which we make decisions. Despite Australian all industry 1992-93 data showing 80.5 per cent of costs came from occurrences which permanently altered peopleÆs lives, New South Wales is still the only state reporting permanent disabilities. In 1991 - 1992, the rate of permanent disability per 1000 wage and salary earners was two. In 2000 - 2001, it was over four û more than doubled. Also strongly motivating is the huge cost. Industry carried 25 per cent of the $34.3 billion costs for 2000 - 2001, up ten per cent of 82.8 billion if the costs of pain, suffering and early death are included.

Jan 1, 2005

By Smit J. G

Following an increase in the number of methane ignitions in South African coal mines a new ventilation system was developed. The "Hydravert" system conceived in late 1979 for use in low seam coal mines, where the bord and pillar method of working is used, has been extensively developed to include applications for mining seams up to 4.5 metres high. A brief history of the development is supplied including some of the pitfalls encountered in the hydraulic equipment design and selection.

Jan 1, 1988

By Rose CW

Typical rehabilitation programmes for spoil piles and waste dumps in open cut coal mines involve the spreading of topsoil to assist vegetation growth. In the early years of rehabilitation before a protective vegetation cover has been established, this topsoil is susceptible to erosion during rainfall events. Since the long term success of rehabil- itation procedures is sensitive to adequate topsoil maintenance and since, on many mine sites, topsoil is a scarce resource, erosion losses of topsoil (particularly once fert- ilised) can severely restrict rehabilitation Measures.

Jan 1, 1983

A career in the mining industry is both challenging and rewarding but comes with some unique complications. Few other industries have such a far reaching effect on individualsÆ lifestyles. Furthermore, few people working within the resource sector could say their job has had no effect on their lifestyle. Mineral deposits in Australia seem to exist predominantly in remote locations like Telfer, Mount Isa and Olympic Dam. With this comes a choice for young professionals; one that is not easy to make, with either alternative often having its pitfalls. This remote nature usually requires professionals (especially graduates and juniors) to choose between a fly-in, fly-out location or relocation to a remote town with less facilities (and some may argue attractions) than their coastal cousins. The challenge for young professionals is to pursue a career that will satisfy their professional goals while developing and maintaining away of life that is emotionally fulfilling.

Jan 1, 2005

Modern, high-output, continuous process plant requires heavy capital expenditure and is exroected to achieve a high rate of return upon the investment made, thus its high utilisation is an economic necessity. Downtime is extremely expensive not only in terms of idle capital but also in terms of lost production and revenue. A sound maintenance management system can alleviate the problem of unscheduled stoppages and a key document in the maintenance system is the Work Order because it both initiates work and conveys maintenance control information back to the administrator. This key document must be supported by an information base that provides technical data, job procedures, spare parts, history and costing. To be effective this information must be easily and immediately available to all concerned. Computer technology has developed extremely rapidly over the last ten years and with it a wide variety of on-line computerised maintenance systems. Selection of the most appropriate system for a given industrial plant is not a straight-forward process. Computer requirements for hardware and software must be matched to the requirements of the maintenance system and such matching must be carried out in an ordered and rational way. At Kalgoorlie Nickel Smelter, time was taken to review the existing maintenance system, select, study and test the new computerised maintenance management package and plan its implementation. As a result, the initial target of equipment recognition has been achieved on schedule and within budget.

Jan 1, 1987

In response to requests from the iron ore mining industry, the Commonwealth Scientific and Industrial Research Organisation (CSIRO) Division of Mineral Physics has developed a number of bulk analysis techniques in which analyses are obtained directly from ore samples weighing many kilograms or from ore located on conveyor belts.Because penetrating neutron and gamma radiation is used, measurements are obtained from a large volume of ore, which ensures thal the analyses are represelllative of the bulk.Two different gamma-ray techniques have been developed to measure iron ore grade. The first is based on backscallering of 60CO gamma rays, while the second involves measurement of the annihilation radiation which arises when the ore is irradiated wilh 226Ra gamma rays. Both techniques measure the iron concentration with an accuracy (1 s) of better than 0.4% Fe.A thermal-neutron irradiation technique using a 252Cf neutron source has been developed for the simultaneous determination of iron and the aluminium impurity (expressed as AI2O3) in iron ore fines on a conveyor bell. Because the conveyor speed must not exceed about 0.05 m/s, if good accuracy for AI2O3 is required, an auxiliary analysis bell is required Lo avoid inLerference with normal ore processing. Dynamic trials have demonstrated that accuracies of 0.6% Fe and 0.1% AI2O3 can be obtained.

Jan 1, 1985

By Lunt D

Arsenic is classified chemically as a metalloid. That is, it has properties intermediate between those of metals and non-metals. Like non-metals, it combines with many metals to form arsenides (eg arsenopyrite FeAsS, niccolite NiAs, sperrylite PtAs2), but like metals it forms sulphides and oxides (eg realgar AsS, arsenolite As203). Arsenic is distributed widely in the Earth's crust at an average concentration of 1.5 mg/kg and is present in more than 150 minerals.

Jan 1, 1991

Attention is drawn to the largest eruptions with dense rock equivalent (D.R.E.) volumes approx-imating 50 km3. These have been strongly clustered during the last 40 000 years, with 11 recognised in the period 35 000 to 22 000 years ago, and 10 in about the last 9000 years, but none in the period 22 000 to 9000 years ago. With the latest such eruption, at Tambora, only 175 years ago, it is likely that we remain in a period of increased activity. During the last 100 000 years, roughly the period during which modern Homo sapiens has existed as a species, there has only been one eruption an order of magnitude larger (>_ 500 km3 D.R.E.). This took place at Lake Toba, Sumatra, about 75 000 years ago, and is estimated to have deposited ash to a thickness of a centimetre or so in parts of Ethiopia, Somaliland, Saudi Arabia and Iran, and to a thickness of a few millimetres in the eastern Mediterranean. The average interval between global eruptions of this magnitude is probably about 40 000 to 50 000 years. Insufficient work on the Quaternary history of volcanoes has been carried out to suggest where the next such eruption might occur. At Yellowstone, which has been well studied, the average interval between very large explosive eruptions is about 700 000 ¦ 120 000 years.As a prerequisite for magnitude-frequency analysis of eruptions, and hazard and risk impact assessments, it is important to classify past eruptions in a consistent manner. In an attempt to find a universally applicable method to estimate order of magnitude D.R.E. volumes from the distribution of airfall tephra, an empirical correction has been derived for the elongation of tephra dispersal fans due to wind. Dispersion distances for various thicknesses of tephra, recalculated for windless conditions, have been obtained from a study of about 40 tephra isopach maps for which D.R.E. volumes have been calculated, and a range of distances derived, equivalent to D.R.E. volumes from 106 m3

Jan 1, 1990

By C McInnes

The key to successful flotation plant design, production planning and mine/mill optimisation is a solid understanding of the resource to be processed. As advocated by the authors of this paper, the main components of geometallurgical modelling of an orebody and its associated flotation plant are: an ore sampling program and subsequent laboratory testing of these samples in order to extract process model parameters; geostatistical distribution throughout the resource model of the process parameters; calibration of the plant via benchmarking (for existing operations); and plant simulation using a system of process models and the distributed metallurgical parameters (from step two) as the data set.It is important that the grinding and flotation models are linked. For example, a laboratory test conducted on a drill core sample, intended to represent a portion of the orebody, is conducted at a specific grind (represented by a P80). However, when that ore is actually processed through the plant it may well be (and in many cases most likely will be) at another P80. Additionally, the flotation plant residence time will often be determined solely by the grinding circuit capacity and feed slurry density. In the case of SAG mill û ball mill circuits, the fluctuations in tonnage and grind are known to be high. The modelling approach described in this paper allows for changes in the measured flotation kinetic parameters in order to reflect the expected grind as determined by the comminution process.

Jan 1, 2005

A feasibility study will fail its objective if it does not identify and then correctly assess, all the risks which could have a substantial impact on the financial viability of a project. Before this assessment can be undertaken, one needs to understand the risk profile of the entity which is making the decision about the project. Some of the commonly encountered issues when assessing project risk are related to the problem of not being able to see the wood for the trees. In any risk analysis it is important that conservatism does not strangle a viable project; that the variables are internally consistent with each other, that reality checks are carried out and that appropriate expertise is used. Sensitivity analysis forms a part of the overall project risk assessment; however, it can only test those variables which have already been identified in the financial model. The most useful tool in performing a sensitivity analysis is Monte Carlo simulation. When properly used, it provides a more real world scenario than the simple adjustment of key variables by ¦ 10 per cent one at a time. Monte Carlo can provide valuable information about the robustness of a project. Project risk and sensitivity assessment is prone to the analysis paralysis syndrome. The focus should be on quality rather than quantity.

Jan 1, 1997

By Wilson CJN

The central Taupo Volcanic Zone is a region of intense Quaternary silicic volcanism accompanying rapid crustal extension. Modem central TVZ is the most frequently active and productive silicic volcanic system on Earth, erupting rhyolite at c. 0.28 m' s'. The rhyolites show no major compositional changes with time, but the total extent of magma chamber zonation has changed with the advent of rifting and crustal extension at c.0.7 Ma. At least 34 caldera-forming ignimbrite eruptions have formed a complex sequence of relatively short-lived, nested and/or overlapping volcanic centres in central TVZ. Taupo contrasts with other large silicic magmatic systems in the exceptionally high frequency, but small size, of caldera- forming eruptions. This contrast reflects the thin, rifted nature of the TVZ crust, that precludes the development of long- term magmatic cycles at Taupo.Within central TVZ, non-rhyolitic compositions have been erupted apparently irregularly in time and space; in particular there is no evidence for a geographic separation of basalts from andesites. TVZ is a rifted arc, but its segmented nature, high thermal flux and voluminous rhyolitic volcanism make it unique on Earth.

Jan 1, 1995

By Munro DL

The Mary Kathleen uranium deposit is in north-west Queensland, approximately halfway between the townships of Mount Isa and Cloncurry, at long. 1400 009 E and lat. 200 44' S. The deposit Iwas discovered by prospectors of the Walton McConachy Syndicate early in July, 1954, and climaxed a very intensive ground search by hundreds of part-time prospectors. during the uranium boom from March to July 1954ò Numerous small deposits, mostly in the vicinity of Mount Isa, were discovered in various rock environments, but Mary Kathleen is the only large deposit and, apart from a few tons of hand sorted material from the Milo lease, is the only deposit that has been worked. Exploration of the surrounding area, and proving of the economic worth of the deposit, were conducted from the time of discovery until February 1956 by a geological team camped near the deposit. Proving was carried out by drilling a pattern of vertical and inclined diamond drillholes at fifty-foot centres over the outcrop. An adit was driven eastwards through the deposit. Metallurgical research and design work in the South Australian Department of Mines Adelaide Laboratories were based on core samples and bulk samples from the deposit. The signing of a contract in March 1956 with the British Atomic Energy Authority to supply 4500 short tons of uranium oxide allowed mining to commence, and enabled the planned construction of water supply, township and treatment plant to proceed. The open out mine and plant are now serviced by a modern township, four miles away, which is connected to Cloncurry and Mount Isa by road. Although little field work has been done since the exploration phase, this paper differs in interpretation from a previous paper (Matheson and Searl, 1956) in that it is based on a revised structural inter- pretation (Compana, 1958), detailed mapping of progressive exposures in the open out, and a re-examination of diamond drill cores.\

Jan 1, 1968

This paper outlines a range of strategies for steady state optimisation of most types of concentrators. Optimisation is considered in terms of comminution performance, energy efficiency, concentrator strategy and overall mine/concentrator operating philosophies. Application becomes more complex as the range of optimisation is expanded. However, the potential gains also increase. A step by step framework for data collection and analysis is provided. This process is facilitated by powerful simulation and mass balancing programs which are now in common use. Once a sound, steady state rationale for optimisation has been developed, it may be used to provide a fine foundation for process control system development.

Jan 1, 1993

By S M. Mousavi

The issue of estimating evaporation in soils is central to the design of engineered soil caps for mine waste and landfill applications. In general, because evaporation from the soil is difficult to measure in the field, laboratory experiments and empirical methods have been used. Much of the earlier work has been conducted in soil science, although in recent years, geotechnical and geoenvironmental engineers have given great deal effort to this work. The result of this increased interest is the development of numerical models, such as UNSATH and SoilCover for estimating evaporation. In this study laboratory-measured evaporation from soil columns was compared with evaporation predicted using the computer program SoilCover, and the analytical method proposed by Gardner and Hillel. Good agreement among the results was observed. Also the sensitivity of the predicted evaporation to soil hydraulic and geotechnical properties, such as saturated hydraulic conductivity and coefficient of volume change was discussed and the practical implication of the sensitivity were highlighted. The work has application in the design and construction of soil covers over sulfide-bearing mine waste and landfills.

Jan 1, 2003

By G Muller, P Larrondo, M C. Godoy

The categories of Mineral Resources and Ore Reserves that may be used for public reporting in Australasia are defined in the current JORC Code (2004). Most internationally accepted codes emphasise the principles of transparency, materiality and competence in classifying resources. They also provide some guidance in considering the impact of data quality. There is no method recommended in the JORC Code to classify a Mineral Resource into the allowed categories of Measured, Indicated and Inferred for public reporting. A clearly defined procedure is desirable for many reasons, including consistency, repeatability and auditability. The demonstrated use of geological knowledge in the classification method is desirable. In deposits with abundant historical data there can be large variations in data type and quality. Quantification of the error of the estimates may also be considered. Ways to formally incorporate such information into the resource classification process are presented as a first step towards establishing an objective, repeatable methodology that allocates resources into appropriate categories based on defined criteria of accuracy and precision.

Jan 1, 2006

By M Kuruppu, B Besa

Currently, conventional methods of decline development put enormous cost pressure on the profitability of mining operations. This is the case with narrow vein orebodies where current methods and mine design of decline development may be too expensive to support economic extraction of the ore. The time it takes to drill, clean and blast an end in conventional decline development can be up to 473 minutes. This is because, once an end is blasted, cleaning should first be completed before drilling can commence, resulting in low advance rates per shift. Improvements in advance rates during decline development can be achieved by application of the electric monorail transport system (EMTS) based drilling system. The system is composed of a two-boom drill mounted on the monorail and a pneumatic face cleaning system that loads blasted material into monorail containers. The operation allows for drilling of the top part of the face to commence as the monorail loading system continues to clean the blasted material at the development face. The preliminary indication is that an advance rate of 12 m per day could be achieved compared to 6 m per day in conventional decline development. The increase in the advance rate results from increased number of blasts that are possible per shift due to reduced time of cleaning and drilling the development face. The continuous drilling system has the advantage of accelerated decline development and orebodies will be accessed quickly and cheaply. Other advantages of the system include negotiating steep and changing gradients (ie reducing decline length), ability to negotiate tight horizontal curves, small operating room and limited diesel fumes.

Jan 1, 2008

The role of metals in the economy is discussed with regard to the flow of metals through to final demand and is illustrated by data for seven metals. Factors influencing the changing pattern of metal consumption are described, including relative prices. A des- cription and discussion of current metal demand forecasting methodologies precedes a discussion firstly of broad economic trends and secondly of the evolving pattern of metal consumption relative to GDP (metal consumption intensity), as technology and other factors change and as economies mature. The tendency for metal consumption intensity to plateau and decline when economies reach a certain region of per capita GDP, following a rapid rise early in the industrial- ization process, is shown in comparative data for seven metals and six countries.

Jan 1, 1979

As the Mount Morgan electrolytic chlorine plant is the first of its kind installed in Australia, and as the details of this method of producing chlorine have, up to the present time, been kept more or less secret all over the world, the author trusts that this paper may fill a gap in the technical literature of the subject.When an electric current is passed through a strong solution of sodium chloride the following reaction takes place -2 NaCl + 2 H 20 = 2 NaOH + C1 2 + H 2 Chlorine gas is liberated at the anode or entering pole of the current, while caustic soda and hydrogen are formed at the cathode or leaving pole of the current. If the two electrodes be simply immersed in a vessel containing salt and the current be turned on, there will be no result save slight smell of escaping chlorine gas. The passage of the current will have certainly split up the salt water according to the above equation, but as the products would be in juxtaposition they would immediately reunite, and the electrical energy would have been spent without any beneficial result having been obtained. Therefore, the all-important problem in designing an electrolytic chlorine cell is the finding of some effective means of isolating from each other the chlorine and caustic: soda as soon as liberated from the...

Jan 1, 1911

A major problem in the continuous casting of aluminium killed strip steel is the incidence of black and grey lines in the strip surface caused by the alumina inclusions. One place for limiting the number of alumina inclusions is by providing favourable fluid flow conditions in the ladle so that the inclusions float out to the surface or adhere to the ladle wall. In laboratory equipment 20 kg of steel was melted in an alumina crucible of 14 cm diameter in an induction furnace. Deoxidation was carried out while the melt was constantly stirred by argon bubbling. Bubble frequencies were measured at the lance tip using a microphone technique. High speed cine photo- graphy was incorporated to measure melt top surface velocities. Experimental results indicate that the rate of removal of inclusions is a function of both the gas input and the power input. However due to unfavourable surface area to volume ratio, reoxidation of the melt took place. Some other experimental difficulties in working at high temperatures are also discussed such as lance design, melting arrangement and sampling techniques.

Jan 1, 1984