Search Documents

By A D. Campbell

The Homer Tunnel is located in a remote area of the South Island of New Zealand and carries large numbers of tourists to Milford Sound through an avalanche prone area. The tunnel is 1280 m long with a steep ten per cent unidirectional grade descending to the west. Construction of the tunnel began in the 1930s and was completed to a nominal 6 m width in 1954. In 1996, two passing bays were stripped-out to accommodate bi-directional flow of tourist coaches. During all phases of construction and widening there have been episodes of strain bursting.The condition of the tunnel and standard of internal services is below current international practice, principally in terms of; in-tunnel air quality, fire life safety, ground support, and road safety. A number of near-miss events have occurred involving coach fires on the approaches and inside the tunnel. The national road authority, NZTA, is considering a substantial investment to improve amenity and safety of the tunnel.This paper describes the rationale for the proposed upgrade works and the investigations undertaken to enable that design. A holistic approach to road tunnel safety has been adopted that balances the key interrelated safety drivers, namely; tunnel lining, traffic operations, ventilation, power supply and egress while ensuring continuity of safe access to Milford Sound.

Mar 8, 2011

Any Australian who knows of the poverty of the early settlers in the first few years following the arrival of Captain Arthur Phillip with his "first fleet" at Botany Bay must feel proud of the progress that has been made in the 174 years that have elapsed since that momentous occasionGFor all its attractive appearance as reported by Captain Cook and Sir Joseph Banks, the shores of Botany Bay and of Port Jackson proved most ,inhospitable, and the accessible country surrounding them anything but suitable for sustaining the life of the small settlement. It is well known that during the first 15 or 20 years the hardy colonists and un-tfortunate convicts were close to starvation on several occasions and were only saved by the arrival of supply ships, which were dependent on the vagaries of wind and current, and the hazards of the uncharted seas they had to -navigate-.When Australia was little more than a miserable penal settlement, Great Britain was one of the great-powers of the world, and the U,.S.A. was an independent nation with a growing degree of prosperity that even then gave promise of its mighty awakening to become, as it has, a e.olossus of industry and commerce,-and the. leader in living standards of the world to-day.Australia, from such a shaky, and comparatively recent start, has risen to a position in which its living standards rank very high in comparison with those of most of the nations of Europe and America. Exact com-parisons are hard to fix because of the wide variety of factors involved .but the Institute of Pab?Lic Affairs .(Victoria) places Australia fifthin the world, excelled only by the U.S.A., Canada, Sweden and Switzerland. The next best after Australia are the United Kingdom, West Germany and France.How we achieved such a high standard of living is a vast subject for study but some of the economic aspects of our climb from abject poverty to a position of near affluence can readily be identified.

Jan 1, 1962

By W Mahoney, F Clement, E Saraiva

Prefabricated waterproofing sheet membranes are extremely complicated to install in underground sections with complex geometries and, despite being already subjected to quality tests in the factory, the installed membrane often exhibits leakages due to different reasons. Main sources of leaks are the required high amount of welding seams and damages caused during installation of reinforcement, as well as overstretching and poorly installed secondary concrete linings. Also the design of the tunnel lining is strongly influenced and limited by the use of prefabricated waterproofing sheet membranes. The use of sprayed waterproofing membranes for more than a decade has contributed to durability and serviceability, as well as to increasing sustainability of tunnel linings. The presented sprayed waterproofing membrane MasterSeal 345 is an advantageous alternative to prefabricated waterproofing sheet membranes under typical tunnelling conditions, especially in geometrically complex areas, such as in lay-by niches, cross passages and crossover caverns, where installation of conventional waterproofing membranes is inherently difficult, and locating leaks is challenging. This membrane has been successfully used in underground projects with different waterproofing design concepts and under diverse hydro-geological and environmental conditions for over a decade. It provides tunnel designers with different options and optimisation for the design of the tunnel concrete lining. Additional advantages to owners, contractors and designers from the use of the sprayed membrane include flexibility in the design, increased productivity and flexibility in working programming, as well as improved logistics, resulting in significant program and cost savings and reduced long-term maintenance costs. This paper describes the key features of this sprayed waterproofing membrane, its application range and limitations, the waterproofing concept, design options and related benefits. Further, guidance for membrane application and quality control and a summary of two recent project references in the United Kingdom and in Switzerland are provided.CITATION:Saraiva, E, Clement, F and Mahoney, W, 2014. The use of sprayable waterproofing membranes in underground structures – concept, design options, benefits and limitations, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 323–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By P Warner

Mines are often located in remote areas that are not well served by æstiffÆ power grids. Radial transmission networks, high lightning incidence (eg in South Africa the Witwatersrand experiences seven to ten strikes/km2 per year), low short circuit strengths and diesel generation are not uncommon. All these factors result in the electric power supply to many mines being unusually prone to dips and disturbances. æLegacyÆ winder drives û cyclo converters and dc drives û convert power directly from the supply to the motor, with no intermediate energy storage element. Further, they rely on the supply network for commutation and are therefore sensitive to supply voltage disturbances. There is a high probability that a dc or cyclo mine winder will trip during a supply disturbance, often resulting in lost production time and call-outs for technical staff to reset or even repair equipment. In contrast, a voltage source inverter (VSI) ac drive stores a large quantity of energy (in the dc link capacitors) and is fully self-commutating. Hence, this topology is inherently more immune to supply voltage disturbances. Indeed, vendors of ac VSI mine winders make general statements about the superior performance of their drives during supply disturbances. However, the advantages have apparently not been previously quantified. This paper compares different winder drive topologies and their sensitivity to supply disturbances, considers categories of supply disturbances and quantifies the cost of the effects on the different drive types.

Jan 1, 2005

By B Roache

Ground support installation into the face of development headings has become an accepted practice at many Australian hard rock mines. Ground support is installed in the development face to reduce personnel exposure to rockfall while conducting work tasks such as marking up, installing lifter tubes, charging, and face sampling. The ground support system installed in the face is typically friction bolts and mesh. This support system can be effective at reducing rockfall occurrence, but it also increases the cost of development per metre, in terms of capital for the ground support, jumbo and operator capital allocation and the installation time slowing each drill and blast cycle. Other issues associated with meshing and bolting the development face include management of rock bolts and mesh sheets in the fired dirt of every cut, damage to services such as vent duct, geometry issues when installing ground support onto irregular development profiles and operator error. Fibrecrete installation onto the development face for support is an option considered by many mines, but it can be difficult to manage due to the removal of visual indications of misfires and slowing the mining cycle due to the wait time for fibrecrete curing. The use of Thin Spray Liner (TSL) products in underground hard rock mines has been relatively infrequent in the past, mainly due to issues with cost, health and safety, and liner strength. Kanmantoo Mine investigated the use of TSLs for the purpose of development face support, while collecting data on the costs and practicalities associated with their use. Several TSL products were trialled and a preferred TSL product was selected for use as face support. Cost savings, drill and blast cycle timing improvements and other benefits were achieved while meeting the requirement to reduce rockfall risk.

Mar 29, 2023

By S N SHEARD

The use of geophysics in mineral exploration in Australia, and overseas, has increased dramatically over this century. This paper shows that using simple equipment with clever interpretation that the foundations of modem geophysics were laid, using all the same principles. The plethora and diversity of mineral exploration geophysical techniques does not allow a full description of their evolution to be given in such a paper. To convey this evolution, however, the progress of two different geophysical methods, magnetics - a potential field (passive) method, and electromagnetics - an electrical (active) method, are described. Examples of magnetic survey data from the 1920s and more recent vehicle home and airborne surveys are given to show the increase in data quality through technological improvement. A set of four airborne electromagnetic data sets spanning three decades is used to indicate the improvement in electromagnetic techniques. It is argued, that considerable progress is still required in the electromagnetic field to increase its interpretability.

Jan 1, 1992

By S Goff

The Northern Sewerage Project (NSP) is a $650 M infrastructure project that will increase the capacity of the sewerage system for Melbourne’s growing northern suburbs while also helping to protect the Merri and Moonee Ponds creeks by significantly reducing the number of sewage overflows that can occur after heavy rainfall. The NSP consists of two stages: Stage 1 (NSP1) will be owned and operated by Melbourne Water Corporation, and Stage 2 (NSP2) will be owned by Yarra Valley Water and operated by Melbourne Water Corporation.Glass-fibre reinforced plastic (GRP) was used on both NSP stages, however, since Stage 1’s schedule for installation of GRP was slightly ahead of Stage 2’s, this paper will only focus on Stage 1’s use of GRP.NSP1 involves the construction of 7.9 km of new sewer tunnel ranging in diameter from 1.6 to 2.5 m, five main access shafts at depths of up to 65 m, and connections to the existing sewerage system including several access manholes. Construction began in 2007, and project completion is expected in 2012.The original design for NSP1 specified the use of high-density polyethylene (HDPE-) line precast concrete pipes as the final tunnel lining and HDPE-lined reinforced concrete for the access shafts and manholes. During construction, the rising cost of precast concrete pipes and the introduction of an additional GRP pipe supplier in the market justified a review of the tunnel final lining material. The contractor-proposed GRP pipe alternative was accepted for the final tunnel lining based on time and cost savings that were possible without compromising the design intent. After gaining experience with GRP through this design change, Melbourne Water Corporation reviewed and accepted GRP as the final lining for five smaller connection manholes. The use of GRP for the manholes was particularly inventive as the redesign made use of the approved tunnel GRP pipes as both a structural and corrosion-resistant lining.This paper discusses the use of GRP on NSP1; how the change in material, from concrete to GRP, affected the design philosophies assumed during detailed design; and how construction methods were modified to handle the less rigid GRP material. Details on the structural, hydraulic and durability considerations for the design are included, as are details about the time and cost savings and the quality and safety improvements that were achieved during construction.

Mar 8, 2011

By D Bertoldi, C Haines

"The Waihi Gold Mine (WGM) operated by OceanaGold New Zealand Limited is a wholly owned subsidiary of the OceanaGold Corporation of Australia. Traditionally WGM has stockpiled and processed separate campaigns of open pit and underground ore. The ore is processed via a conventional semi-autonomous grinding (SAG) / ball circuit (SABC). The low aspect SAG mill operates in a closed circuit with two 20" cyclones, whilst the ball mill is also a closed circuit with a 10" cyclone cluster. A major wall movement in April 2015 ceased open pit operations indefinitely, 18 months ahead of the mining plan. This immediately reduced the forecast mill tonnage leaving two options: begin campaign milling or change the operating strategy and target lower throughput. Additional cost pressures necessitated improved milling cost efficiency. The immediate ore restriction limited processing alternatives to within the existing major infrastructure. Available comminution circuit survey data laid the foundation for developing a comminution model using the JKSimMet™ software package (version 6, created by KJTech). A number of flow sheet variants were then evaluated based on predicted throughput and efficiency. The comminution models suggested opportunities for improved efficiency lay in reducing throughput and increasing utilisation rather than on/off campaign milling under the existing operating philosophy. A series of process alterations followed, delivering new cost efficiencies that maintained the current $/t processing cost. This paper aims to review the change in circuit performance and examine the decisions and challenges faced following the transition from a high tonnage SABC circuit to lower tonnage SABC circuit.Citation:Haines, C and Bertoldi, D, 2016. The Transition from Semi-autogenous to Autogenous Milling at Waihi Gold, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 303–312 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By G J. Wilkie, P A. Revell

The R&D landscape for ore pre-concentration technologies within mining is characterised by the development of individual technologies and point solutions. This presents METS and mining companies with the combined challenge of understanding how to apply pre-concentration technologies to create maximum value, and how to sustainably integrate the technologies into their businesses to maintain the value. The paper will consider the requirements of an integrated pre-concentration system and presents a portfolio of R&D projects that have co-developed and integrated a suite of new precencentration technologies and methodologies across the mining value chain. Focus areas include in-situ orebody characterisation, blast design, real time cross belt mineral sensing, and consideration of how much data needs to be acquired in order to make value based decisions between ore pre-concentration options. An ore pre-concentration workflow is presented to demonstrate how additional optimisation opportunities are enabled both by moving decision points further upstream in the value chain, and by integrating the concepts of pre-concentration into the design of mineral processing equipment. Additionally, several research projects examine the non-technical factors that present barriers to uptake of new technologies within mining companies. Organisational culture, risk management and socio-political factors are discussed and a set of management tools are presented that allow organisations to self-assess their readiness for new technology uptake, along with process models to assist management with identifying and navigating the ecosystem of stakeholders that are decision makers in the use of pre-concentration technologies.

Nov 10, 2020

By I D. Gregson, A Gandhe, A S. Garcia, K M. MacAndrew

"Falls of ground still cause around one-third of all underground mining fatalities. The recent introduction of mechanised room and pillar working into Indian coalmines is an example of the application of new design by measurement and safety monitoring strategies, which can be used to reduce falls of ground risks in mines.Rock Mechanics Technology, now part of Golder Associates UK Ltd (Golder), is providing rock bolt support and pillar design services to the mines using a design by measurement approach. This involves in situ monitoring to confirm support and pillar designs and pillar extraction sequences.Site examples are given of the support designs determined and the monitoring programs undertaken for both design and safety.Routine safety monitoring of roof movement using telltales is also described. A new auto warning telltale has been developed specifically to warn of imminent caving as pillars are extracted.The approach used by Golder has played a major role in ensuring the success of these projects. As a consequence, mechanised room and pillar working is now firmly established in India, and wider application is planned to help meet future demand for coal.The experience confirms that the design by measurement method for this application has important advantages over conventional design approaches using analytical or empirical methods. Firstly, it measures the design performance or outcome rather than trying to calculate or predict it. Secondly, it provides the opportunity for the design to be adjusted to obtain the optimum outcome. Thirdly, it can do this at a local level, so that the support design can be matched to changing conditions to give the most cost-effective design. Finally, it incorporates long-term monitoring of support performance, again at a local level, so that subsequent change can be identified to enable corrective measures to be implemented in a timely manner and to ensure that ground control safety is maintained.CITATION:MacAndrew, K M, Garcia, A S, Gregson, I D and Gandhe, A, 2014. Application of design by measurement for support and pillar design in mechanised room and pillar coal mining in India, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 65–76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By A Campbell

Open pit blasting at Ernest Henry Mining has the potential to cause damage to nearby underground workings. This paper is a case study of the blast vibration management project that was conducted to ensure open pit blasting did not adversely affect the stability of upper production levels or cause damage to the underground primary fan units. The two upper levels of the underground mine surround the lower portion of the open pit mine. The remaining underground mine workings are directly below the open pit mine. This paper details the process developed to prevent open pit blasting causing excess vibration in the underground mine. Measurement of test blasts combined with historic blast monitoring data was used to determine site specific blast vibration parameters. Threshold vibration levels for blast-induced damage to underground drives and the fan chambers were developed from benchmarking and non-linear numerical modelling. A Monte Carlo simulation model was used to predict vibration levels in critical underground areas. Blasts predicted to exceed maximum vibration levels could then be redesigned to avoid damage.A scale distance law for determining peak particle velocity (PPV) from the distance and charge weight of blasts was developed. Underground observations were used to develop a site-specific relationship between PPV and ground support/rock mass damage. A Monte Carlo superposition prediction model was developed and compared to measured data to refine input parameters. Standards for redesigning open pit blasts in order to reduce blast vibrations whilst minimising impacts on productivity are described. Non-linear numerical modelling was used to establish the dynamic capacity of the fan chambers, and set a PPV of 250 mm/s as a threshold for damage. The numerical model captured the full dynamic behaviour of the fan chambers and installed support, including transient stresses, strains and induced damage, when subjected to a simulated open pit blast.This case study also outlines a procedure for monitoring and predicting blast vibrations at other mine sites where open pit blasting has the potential to impact on a nearby underground mine.

Nov 8, 2011

By C Armstrong, B Wentzinger

Upstream embankment raises often represent the lowest cost option for increasing the capacity of tailings storage facilities (TSF), but also pose the highest stability risk due to constructing on top of previously deposited tailings.This paper presents an overview of key aspects in the geotechnical investigation and design of upstream raises and some recent lessons learnt from experience across a number of TSFs in Australia. A summary of recommended field investigation and laboratory testing methods is provided with a focus on collecting quality information for design purposes. A strong focus is given in developing an accurate assessment of pore water pressures, which, if not correctly understood can have disastrous consequences on tailings strength parameter interpretation and wall stability assessment in static and post-seismic conditions.The assessment of the contractive or dilative shearing behaviour of the tailings material and rigorous interpretation of design characteristic values are presented. Some comments on stability analysis options and proposed methodology are also provided.CITATION:Wentzinger, B and Armstrong, C, 2018. Lessons learnt in geotechnical investigation and stability analysis for upstream tailings storage facility raise design, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 333–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By D J. Robinson, L L. Kuhar

"Regardless of orebody value, at some stage, the pit will reach a depth where the reward for mining wider and/or deeper is not justified by the anticipated returns. ‘Last-blast’ strategies may help to some degree in recovering additional quantities of the resource but when a pit remains, there is often significant value left in the ground. In addition, in many cases, one or many good reasons may dictate why going underground and pursuing the orebody below the pit is also not justifiable. Whereas the company can hopefully move on to other more prospective parts of the orebody, the remaining options for the pit are usually very limited. Typically the pit is either held for potentially more favourable future pit expansion opportunities or it could be used for an alternative purpose, such as tailings or waste storage. This paper will present an alternative option that involves the direct extraction of values using in situ recovery (ISR) methods to recover additional value metals from the walls and/or floor of the pit. ISR involves circulating a fluid through the remaining orebody, solubilising the target metal and subsequently returning the solution to the surface for metal recovery. ISR is not the panacea to all but it has been employed selectively in the minerals industry for some time and the production of metals, such as uranium, rely heavily on this approach. ISR is not yet considered by many operators as an approach to compete with open pit or underground mining, largely because of the perceived limitations of this approach and the perceptions of risk. Rapid recent development of tools and enabling technologies relevant to ISR have made us reconsider the most economic approach to extracting many other metals from known mineral systems, even those currently listed as subeconomic. We suggest that ISR has the potential to make mine operators rethink the end of the pit life and adopt an innovative ISR approach to work toward a more complete recovery of value metals from existing pits.Citation:Kuhar, L L and Robinson, D J, 2016. In-pit In Situ Recovery - a New Approach That May Allow for Increased Value Extraction before Pit Closure, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 275–283 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By X Li, W McKeague, M S. Powell

This paper explores the importance of operators in the overall efficiency of mineral processing plants. With the potential of future control configurations becoming more remote, it is time to review the implementation of control and utilisation of operators. This paper is based on a preliminary review of operators and control room operations and clearly shows that, in the minerals industry, operations are typically run in a reactive mode (with a focus on ensuring equipment operation), rather than in a proactive mode (with a focus on optimising the process performance). The primary reason for this misguided approach is the short sighted thinking applied to the challenges of designing technology and organisational tools capable of addressing the essential operational needs: an approach which inevitably results in a disconnect between people and technology. Contrary to the popular approach of replacing operators with expert systems, the thesis of this paper is that the shift to more complex circuits, with higher demands on processing capability and control, will require the actual upskilling of operators. Experience in mineral processing and other industries indicates that expert systems cope well with small changes but are typically unable to respond to major changes in feed material and this is where the expert operator becomes crucial. Providing operators with ongoing high level training in process understanding, and restructuring how they interact with the plant and interface with the control system is the approach being proposed here - an approach surprisingly underutilised and often absent in the minerals industry today.CITATION:Li, X, Powell, M S and McKeague, W, 2012. Unlocking processing potential by empowering our operators, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 333-340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By S Amor, A Beasley

This paper provides an example of how industry can respond to the implementation of new regulatory approaches to mining risk, health and safety by adopting a robust, practical, software-based approach to the management of risk accountabilities in terms of competence, experience and suitability for obligations and responsibilities, as required in Queensland Coal Mining operations due to the introduction of Recognised Standard 22 (‘RS22’; Resources Safety and Health Queensland, 2021). Based on the authors’ experience from working with several Qld mine operations, it offers a snapshot of the experiences, approaches and reservations faced collectively by industry as a result of the introduction of RS22. Several challenges exist within the detail of RS22, leading to varied interpretations, implementation strategies and overall compliance between mine sites. Arguably the single biggest challenge identified has been how to find a balance between compliance and practicality – considering cost, operational interruption, available pathways for delivery of competence, ongoing compliance and value adding to the business operations and people. Software-based solutions are increasingly being relied upon to address the introduction of new regulatory approaches and the significant administrative load placed on mining operation Site Senior Executives (‘SSE’) due to RS22 means this case is no different. This is further complicated given the continuous, ongoing changes with the site management structure witnessed by the authors across each of the mining operations as a result of continuous changes to personnel, the site risk profile and an overall mining industry uncertainty of how to respond to RS22. The stringent reporting/notification requirements under legislation compounds this further. The approach put forward by the authors is a well-considered rationale and approach to the application of training and skilling; and equally how to ‘future proof’ the coordination of site training needs around changes to the Management Structure, the Risk Register, skilling processes and succession planning. A brief investigation of other legislative frameworks concluded this approach would likely meet or exceed expectations of jurisdictions across Australia and overseas, making this a highly flexible approach for establishing a competent Management Structure to provide safe systems of work.

Apr 16, 2024

By D Mee

The Western Mining site at Olympic Dam, near the community of Roxby Downs in South Australia is one of the largest orebodies of its type in the world. It contains known reserves of over 10.6 M tonne of copper, with economic secondary metals including uranium, silver and gold. In 1996, an expansion project was commenced to increase mine production approximately threefold, to produce 200 000 tonnes pa of copper, 4600 kg pa of uranium oxide, 3600 kg pa of gold and 50 000 kg pa of silver. This expansion included both underground mining and surface processing investment. Because of the scale of operations, it was decided that ore should be transported underground by a railway system. In July 1997, ALSTOM Automation and Control Limited (then Cegelec Australia Limited), was awarded the contract to deliver a control system to manage and automate the rail haulage system for Western MiningÆs Olympic Dam Mine, as part of this major upgrade and extension project. This paper explains the overall design and the approach taken to implement route selection, route locking, train interlocking and track topology using normal industrial control equipment such as Programmable Logic Controllers. Included is a discussion of how this automation has improved the productivity of the haulage system by more than 15 per cent.

Jan 1, 2000

By R Wilson, S Luke, R Williams, B Freeburn

"In 2010, two McLanahan RSS14×50 scrubber screens were installed at Fortescue Metals Group’s (Fortescue) Christmas Creek site. By 2015, the trommel (screen) section had effectively reached the end of their serviceable life. This was determined by regular measurement of structural components over the previous 18 months that tracked wear life. At the same time, numerous trials and optimisations had taken place on screen panel design and material composition. During 2015, a new set of trommels were designed, manufactured and installed that incorporated many new features: increased open area to facilitate high throughput, improved wear protection for structural members, simplified trommel panels and realigned discharge ports to reduce wear on exit. Numerous other upgrades have taken place on the drive system, feed chutes, liner and weir configurations and park brake, to name a few. This paper will highlight how regular measurement drove design changes and how the site and the original equipment manufacturer (OEM) managed a replacement program that has delivered improved performance.Citation:Wilson, R, Luke, S, Freeburn, B and Williams, R, 2016. Regular Measurement Defines Upgrades on Scrubber Screens, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 285–290 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By R McIlwraith, B Breul

Two case studies are presented in this paper. The first one discusses a roller compacted concrete water supply dam that was constructed in El Mauro in Chile to provide water for agriculture activities downstream of a copper mine during the dry season. The 23 m high dam used a bituminous geomembrane (BGM) as the low permeability upstream facing element on the dam to control seepage through the dam. This is the first time that a BGM has been used in this application. A deep cut-off trench was used to control seepage beneath the dam and through the abutments. This paper briefly presents the design of the dam, including selection of the concrete mix and maximum aggregate size that the use of the Coletanche BGM allowed, and provides details of the construction, quality control and assurance of the installation of the BGM. An ultrasonic apparatus was used as part of the quality control on the BGM seams.The second case study discusses a tailings dam in Cerro Lindo, Peru (near Chincha), where a watertight BGM was installed on the upstream face. Results are presented of the survey done by a consultant on the behaviour of the dam and in particular of the BGM following an earthquake of magnitude 8.1 in Chincha close to the site. These findings on-site were checked by trials in a laboratory in California. Test results are given and explained.CITATION:Breul, B and McIlwraith, R, 2015. Case histories – roller compacted concrete dam waterproofing with a bituminous geomembrane in Chile and a tailings dam in Peru subject to an earthquake of 8.1 magnitude, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 367–372 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By R N. Humphries

The aim of this paper is to question the need to develop bespoke monitoring and assessment methodologies and criteria, thereby ‘reinventing the wheel’, when designing and assessing the success of important natural habitat and ecosystem restoration schemes at mine sites in the UK and Australia. It draws attention to the existence and applicability of the Phase I Habitat, National Vegetation Classification (NVC) and Condition Monitoring methods in the UK and similar approaches used in Australia. These are long accepted established methodologies and have published accounts for describing, assessing and managing natural vegetation communities, habitats and ecosystems. They are often used at the environmental impact stage, but seemingly rarely, if at all, in restoration design and management at mine closure. Their application to mine restoration and closure is illustrated and discussed by reference to a surface coalmine in South Wales, UK.It is concluded that the application of a combination of the Phase I Habitat, NVC and Condition Monitoring methods is highly relevant to the expectations of the Convention on Biological Diversity (CBD) and its implementation in the UK, and probably in Australia too. The methodology and criteria described could be incorporated into the guidance and specified in the mining permits so that there is clarity as to the expectations and requirements for monitoring and assessment for bond release. Their use could be of wider application where there is a requirement to assess the success of restored CBD assets and ecosystems.CITATION:Humphries, R N, 2014. Why reinvent the wheel when there are established methodologies to aid the design and assessment of restored natural ecosystems on mined land?, in Proceedings Life-of-Mine 2014 , pp 675–692 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By P Card

Some project managers accept unsatisfactory economic evaluation modelling because they are unaware of what constitutes good practice. They tend to leave it to the evaluation specialist or others to decide. The AusIMM has published on its website a draft set of guidelines for technical economic evaluation which will allow these project managers to take control and demand worldÆs best practices.The style of the guidelines is described and the source of a worked spreadsheet example in Excel is given.Economic evaluation in project management is described. A simple test for the acceptance or rejection of evaluation work is offered. The nature of modelling and evaluation in each of the three study phases of concept, prefeasibility and final feasibility are described. Suggestions on the selection of specialists for each phase are given. The three levels of evaluation thinking are described, namely, modelling, valuation and evaluation. Finally the meaning of æfinancial analysisÆ is explained.The conclusion is that æthe role of an economic evaluation specialist is to create models and evaluations for the whole project team to readily understand and use: it is not to create models for his/her own useÆ.CITATION:Card, P, 2012. What project managers must demand from an economic evaluation!, in Proceedings Project Evaluation 2012 , pp 173-176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012