Search Documents

Cordeaux Colliery is more logically sited than the historic escarpment Corrimal Colliery, on the same reserve. At Cordeaux the modernisation of mine plans and equipment and the introduction of high production longwalls have created a record achieving producer of both steelmaking and export coals.Further changes achieved have been in employee related attitudes and performance, enhanced by business strategies and total quality control and particularly benefiting from innovative employee input With this present example of co-operative effort Cordeaux Colliery will continue to improve through management of total quality. resources, development rates and customer satisfaction.

Jan 1, 1991

Confirmation of significant mineable reserves of high grade silver ore at Elura Mine has led to the development of a high cost, high recovery mining system. At the contact of oxidised and sulphide ores lies a supergene zone of enrichment which has provided a contrast, not formerly imagined, to Elura's primary development and stoping operations. Because of the soft nature of the ore, intense ground support practice has been combined with a panel cut and fill continuous mining system to extract a reserve of small, but most valuable Proportions.

Jan 1, 1988

By Kovscek P. D, Thimons E. D

The Bureau of Mines equipped a longwall shearer with a water- jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 1 MPa and with water-jet-assisted cutting pressures ranging from 7 to 40 MPa. At water pressures of 20 MPa and higher, dust concentrations were reduced by as much as 85 % via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1988

By Hunter T. C

The wirebar furnacing and casting facility commissioned in 1970 at Copper Refineries Pty. Ltd. (CRL), Townsville, comprising a 70 tonne/ hour ASARCO shaft furnace and a Walker type casting wheel, contained several unique design features. Since commissioning, effort has been directed at improving metallurgical control of the casting process. This has resulted in the identification of optimum mould lubricant properties and the use of continuous on-line measurement of molten metal oxygen content. Casting defects such as cracks and surface porosity are readily explained and controlled using these techniques.

Jan 1, 1977

It is important to prevent the overload ing of mills being operated near maximum tonnage. Changes occurring during overload differ in their usefulness as guides to control action. The Primary Ball Mills of Bougainville Copper Ltd. provide an example of some of the problems and progess in avoiding overload.

Jan 1, 1978

Crystalline glass defects (usually referred to as stones) come in a wide range of compositions and from a variety of sources. Complete identification requires a determination of the mineral phases present and their textural arrangement. Until the source has been determined, no remedial action can be taken to eliminate the problem.

Jan 1, 1989

This paper examines the concepts of risk analysis and uncertainty in open pit mine design. It describes the relationship between risk analysis and uncertainty, describes methods that can be used to quantify uncertainty, and suggests ways of reducing the geological and geotechnical uncertainties that are inherent in open pit mining.

Jan 1, 1994

A combination of highly structured, fissile stope hangingwalls and high ground stresses have caused difficult mining conditions in the Main Lode Deeps at Lancefield Gold Mine. Cyclic reviews of ground support and stoping techniques, coupled with geotechnical investigations, and the application of numerical modelling has led to the successful management of stoping operations.

Jan 1, 1995

By Hayward N, Sutherland D, Wilkie G

A pilot plant study has been made of the liberation characteristics of a nickel ore under different milling conditions. A series of runs were made ranging from fully autogenous grinding to semi-autogenous grinding with a ball load of 8%. The mill products were sized and assayed then analysed by QEM4SEM. This enabled a full liberation analysis to be carried out to see whether the autogenous grinding leads to improved liberation by promoting selective breakage. Though it is frequently claimed that fully autogenous grinding yields superior liberation this could not be detected in the present study.

Jan 1, 1991

As part of its Concentrator operation Hamersley Iron Pty. Limited uses wet high intensity magnetic separation to upgrade shaley low grade ore in the minus 0.5mm size range. Materials handling problems, largely caused by fine ore types and design deficiencies, surfaced in the Fines Treatment Plant soon after Concentrator commissioning in 1979. Surging throughout the circuit impaired process efficiency and added to problems caused by capacity and process control limitations. In 1981 extensive modification works were initiated to supplement minor changes made to that date. The new circuit significantly increases capacity and provides greater process control.

Jan 1, 1978

Pyrrhotite is the predominant gangue mineral at Renison comprising about 60 percent of the sulphides in an average ore blend. It exists as two crystal structures - monoclinic and hexagonal. Monoclinic pyrrhotite is the slowest floating of all minerals but is ferromagnetic and hence recoverable more efficiently by low intensity magnetic wet drum separators than flotation. This paper discusses the installation and commissioning of four 0.915 m x 3.0 m, 0.1 Tesla permanent magnet, wet drum separators prior to sulphide roughing flotation. Planned circuit and process control modifications to better accommodate magnetic separation into Renison's flowsheet will be Discussed.

Jan 1, 1991

The Olympic Dam copper-uranium-gold-silver deposit, located approximately 520 km north-northwest of Adelaide, South Australia (Figure 1) was discovered in 1975 by Western Mining Corporation. A joint venture to facilitate development of the deposit was formed in mid-1979 between WMC (51 per cent) and the British Petroleum Group (BP, 49 per cent). Production commenced in 1988, and current annual output from the mining and treatment of 2.2 Mt of ore is approximately 65 000 t of refined copper and 1400 t of uranium oxide. Significant amounts of refined gold and silver are also produced.

Jan 1, 1993

Before attempting to outline the Australian Stock Exchange's perspective on expert reports, I think it would be appropriate to explain to those of you -who are not familiar with the Stock Exchange listing rules on just when ASX currently requires companies to obtain an expert report and equally important to note, what the regulators have to say.

Jan 1, 1989

Adsorption isotherms, zeta potential and coagulation techniques have been used to exa- mine the mechanism of metal activation on SiO2 and ZnS surfaces. The importance of surface nucleation or precipitation of metal hydroxide coatings is'established and identified-by characteristic charge reversal patterns. The significance of surface coatings in sulphide and non-sulphide flotation is discussed.

Jan 1, 1973

By Burrell I

This paper describes recent developments at West Cliff Colliery in environmental monitoring, using a sophisticated computer controlled system. The operations involved in environmental monitoring are described and the equipment employed is detailed. It is anticipated that the monitoring system employed at West Cliff Colliery will be expanded to allow total and instantaneous monitoring of roadway environmental Conditions.

Jan 1, 1983

Developments in mining technology are outlined which point out that longwall face technology has the capacity to produce 20,000t/d on a regular basis. The optimum length of longwall faces is about 250m. Developments of headings and gate roadwyas require radical changes to meet longwall developments. New conceptual models are outlined to meet the challenge.

Jan 1, 1988

Heavy media separation serves to upgrade mill feed and reduce unit operating costs, allowing ores to be mined which could other wise be uneconomic. At the Aberfoyle mine at Rossarden in north-east Tasmania, a simple heavy media operation using a converted Akins screw classifier as a separating vessel, removes barren quartz from mineralised material. At the Cleveland mine at Luina on the west coast of Tasmania a more complex ore mix requires a versatile operation combining hydro-dynamic and static separation equipment to provide an efficient beneficiation circuit. The two operations are briefly described with a background of basic heavy media separ- ation practice.

Jan 1, 1978

By Matsumura T, Takematsu T

The Brown Coal Liquefaction Process (BCL Process) has been developed by Nippon Brown Coal Liquefaction Co., Ltd. (NBCL), and a 50-ton-per -day Pilot Plant has been partially completed and put into operation by Brown Coal Liquefac- tion (Victoria) Pty., Ltd. (BCLV) at Morwell, Victoria, Australia. This Project has been sponsored by New Energy Development Organization (NEDO), an or- ganization associated with MITI, and has been promoted as a National Project with funding by the Japanese government. This project has also been conducted as a cooperative technology de- velopment project between the Japanese and Aus -tralian governments since 1980 and has been supported by the Victorian state government and

Jan 1, 1987

Heavy media separation serves to upgrade mill feed and reduce unit operating costs, allowing ores to be mined which could other wise be uneconomic. At the Aberfoyle mine at Rossarden in north-east Tasmania, a simple heavy media operation using a converted Akins screw classifier as a separating vessel, removes barren quartz from mineralised material. At the Cleveland mine at Luina on the west coast of Tasmania a more complex ore mix requires a versatile operation combining hydro-dynamic and static separation equipment to provide an efficient beneficiation circuit. The two operations are briefly described with a background of basic heavy media separ- ation practice.

Jan 1, 1978

Two significant TBM boreability predic- tion models are outlined. Predicted advance rates are compared with actual advance rates taken from twenty case histories. The results show that a simple low cost method that uses one machine parameter and one rock parameter compares very favourably with a high cost sophisticated method which also includes information regarding discontinuities in the rock mass. The effect of rock texture on drillability is also examined. A method of quantifying rock texture has been developed and is outlined. Experimental results show that the developed TEXTURE COEFFICIENT returns highly statisti- cally significant correlations with drilla- bility data in a wide range of rock types.

Jan 1, 1987