Search Documents

The Small Pebble Process for Reducing Ball and Power Consumption in Secondary Grinding Ball mills are used widely for secondary grinding. A mixture of ball sizes can be used to optimise grinding efficiency, but the use of balls smaller than about 30 mm in diameter is not normally viable, particularly when alloy steel is required. Preliminary testing of the grinding efficiency of various combinations of 40 mm steel balls and crushed stone in the size range 7 to 25 mm was carried out in a 300 mm diameter mill, which has accurate power measurement.The primary interest was to assess the potential benefit of adding small pebbles (from a primary circuit crusher or mill) to a secondary ball mill, to reduce ball consumption and to improve grinding efficiency. The optimum proportion of pebbles was found to be about 25 per cent by volume. This mixture produced about the same amount of fines as balls alone, but with lower power consumption, due to the lower density of the pebbles. The net result was a 12 per cent saving in power and a 25 per cent saving in ball consumption. The production of fines was partly due to pebble wear. The use of portions of 15 mm balls, (ceramic and steel), was also tested for comparison. A few batch pilot-scale tests were conducted in a 1.2 m diameter, 0.31 m long mill to test the viability of the pebbles at a larger scale. The pilot-scale tests confirmed the reduction in power and that the rate of production of fines was the same as that obtained with balls. The same residence time was used and this implies that pebbles can be added to an existing full-scale ball mill, with no loss in capacity. Samples of secondary mill feed and pebbles were obtained from a copper mine and the steady-state consumption of pebbles was determined by locked-cycle laboratory-scale tests. These tests demonstrated that mill power could be reduced by up 13 per cent and that the consumption of 40 mm balls could be reduced by up to 38 per cent, while maintaining the same throughput and product size. The rate of pebble addition was about 4 per cent of the primary circuit feed rate. Application has been made for patent protection.

Sep 13, 2010

High-sulphidation (HS) gold, silver and/or copper deposits are generated in both the epithermal and the upper parts of the underlying porphyry environments over vertical intervals of up to 2 km. The HS deposits are generated in advanced argillic lithocaps, which are products of the absorption of acidic magmatic volatiles by voluminous groundwater systems. Mineralisation styles in HS systems reflect depth of formation as well as the interplay between structural, lithological and hydrothermal parameters. The deep parts of HS systems, at depths of >1000 m, are typified by disseminated copper¦gold mineralisation comprising digenite, chalcocite and covellite in pervasive advanced argillic as well as underlying sericitic alteration. In highly telescoped systems, such mineralisation may overprint porphyry stocks and associated quartz-veinlet stockworks. Intermediate levels of HS systems commonly contain fault-controlled copper-gold mineralisation, typically as enargite in bodies of vuggy residual quartz, silicification and/or massive pyritic sulphide. The shallow parts of HS systems, at depths of The exploration focus is on four principal HS mineralisation styles:copper (eg Chuquicamata, Monywa) or copper-gold (Wafi) in the deep porphyry-hosted parts of systems preferably, in the case of the latter, where supergene oxidation is limited and, hence, flotation may be used for metal recovery; copper¦gold-bearing replacement mantos and pipes hosted by carbonate wallrocks in the deep parts of systems (eg Bisbee); high-grade gold in late-stage veins or hydrothermal breccias that overprint the intermediate to shallow levels of systems (eg El Indio, Goldfield); and large, bulk-mineable gold deposits in the shallow parts of systems that were subjected to supergene oxidation, thereby permitting heap-leach treatment (eg Yanacocha, Pierina). To these preferred HS styles may be added the low-sulphidation vein or disseminated gold¦silver mineralisation that is commonplace alongside many HS systems (eg Victoria at Lepanto).

Jan 1, 1999

By A Reid, A W. Musk, O Jones

In this paper, the authors attempt to bridge the gap that currently exists between the duty-of-care responsibilities of underground mining industry personnel, and the multifaceted health challenges facing mineworkers in Western Australia’s metal mines where diesel-powered mobile equipment predominate. In addressing this issue, the complexities of the nature and extent of the challenges are discussed along with the current inadequacy of existing regulatory metrics. Support is given to the need for well-organised in-mine baseline studies to clearly define the distribution and aging characteristics of the toxic and carcinogenic pollutants within the mine ventilation system, with special emphasis given to exploring the validity of biomonitoring systems. The paper concludes with the proposal that a template risk assessment data sheet be prepared for the industry to provide mining personnel with a sound basic knowledge of the health risks involved and the control measures and precautions available for minimising and/or eliminating the hazard.CITATION:Jones, O, Musk, A W, Reid, A and Davis, C, 2017. Risk assessment tool for mines using diesel-powered mobile equipment, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 151–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

The paper provides an overview of the development and content of APCOM symposia since their inception in 1961. This development is set within the context of the academic environment in which much of the research published at APCOM symposia is conducted. This environment includes rigorous external assessment of research quality at national levels and against international benchmarks, which carries significant consequences for funding and for the continued existence of the academic minerals industry disciplines. Adverse consequences that undermine the academic provision of mining and resource engineering will impact negatively on the minerals industry by reducing the level of research and education resources available to it.The traditional reductionist approach to research is contrasted with the inter-disciplinary approach that is required to address the complex systems problems that the minerals industry will have to address to ensure its technical, economical and environmental sustainability. Such an approach offers a means of raising research profiles, of establishing mutually beneficial academic-industry engagement and provides an opportunity for APCOM to take a lead role in identifying the research and development agenda for the future

Sep 26, 2011

By S Jahanshahi, D R. Swinbourne

The classical metal-slag-gas equilibrium technique was used to study the thermodynamic activity of cobalt, iron and their oxides in iron silicate based slags containing under controlled oxygen potential (3.70 x 10-8 to 2.95 x 10-7 atm) at 1573 K. The measured activity of cobalt oxide in FeOx-25 wt per cent SiO2 slags showed positive deviation from ideal behaviour for melts with up to ten wt per cent CoO. At higher silica contents, the behaviour became closer to ideal and in accord with previous studies on silica saturated slags. The activity coefficient of FeO in these slags had virtually no dependence on the CoO content. Partial substitution of silica by lime resulted in an increase of the activities and activity coefficients of CoO, FeO, Fe2O3 and Fe3O4. The results indicate that saturation of the slag with a magnetite phase occurs at CaO contents of five wt per cent and higher. Phase equilibria studies SiO2-FeO-Fe2O3-CaO slags containing cobalt were also carried out using the drop-quench technique. Results from these experiments confirmed the formation of a magnetite solid solution containing about three wt per cent CoO at lime contents of five wt per cent and higher at 1573 K and 2.9 x 10-7 atm of oxygen.

Jan 1, 2000

By B Haase, R Saha

Conditional simulation (CS) has been extensively used in metal industry to assess uncertainty of geo metallurgical variables to build robust distributions around grade tonnages across different time horizons. Coal’s entry to nonlinear stochastic modelling is relatively new and this paper summarises the work done at BHP to enable its practical usage from production time frames to Life of Asset planning. CS in coal using Sequential Gaussian Simulation (SGS) is used to understand resource confidence around specific variables within pre-defined boundaries of spatially continuous domains for each coal seam. The variation between simulations for a given parameter reflects uncertainty. This paper demonstrates the use of CS to profile resource based upon agreed seam/parameter uncertainty thresholds which affect planning, forecasting, extraction and inform identification of key production risks and defining mitigation strategies. The end goal is to de-risk long-term plans by optimising infill data collection and improve stability in short-term planning through increased understanding of confidences locally rather than at global resource definition stages. The paper also briefly discusses the use of automated workflows and systems to minimise the time spent on the process to enable use in decision-making.

Mar 22, 2022

By H Zhang, A Lawrence

To accommodate the fast growing need for services in Singapore’s Marina Bay downtown area, Marina South, the construction of a common services tunnel (CST) was required. The CST includes various services such as telecom cables, power lines and water pipes. A deep excavation and temporary earth retaining system (TERS) was required to facilitate the construction of the tunnels. Marina Bay is reclaimed land over thick soft marine clay which is likely to be still consolidating. The deep soft marine clay poses a big challenge for deep excavations in downtown areas where highways and sensitive structures are close by. This paper presents a case study of part of the CST Phase 1B and 2 at Marina South, in particular a 26 m deep excavation supported by a 46 m diameter temporary caisson. The construction started in late 2006 and the basic structure was completed in early 2011. The caisson was formed by 1.0 m thick overlapping diaphragm wall panels with a capping beam and three ring beams at different depths. Two-dimensional finite element analyses were conducted to predict the ground settlement, lateral displacement, bending moment and hoop stresses in the diaphragm wall and ring beams during different excavation stages. A comprehensive instrumentation and monitoring scheme was established to verify the design predictions, control excavation safety and trigger the contingency plan to protect public safety. The impact of construction activity, unbalanced temporary stockpiles and adjacent deep excavation for a mole removal will be discussed.CITATION:Zhang, H and Lawrence, A, 2014. A case history of a deep excavation in a big circular shaft in Singapore marine clay, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 581–588 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By G Baird, M Seto

A low-cost methodology that allows the determination of in situ stresses using oriented core specimens has been investigated. The technique can be used to determine the stresses during the early stages of a project, even in undeveloped areas of a mine. The research aim was to compare the experimental results estimated by the Acoustic Emission and Deformation Rate Analysis methods with those estimated by conventional Hollow Inclusion cell measurements. The studies have been focused on full stress tensor determination from a single oriented rock core. In all cases the rock core specimens recollected the in situ stresses reasonably well compared with the standard overcoring method.

Jan 1, 2000

By A R. McKinnon

The recently opened Hera Au-Pb-Zn-Ag mine in central New South Wales has provided an ideal opportunity to demonstrate the calculation of sulfide ore mineralogy using normative methods. Normative mineralogy applies a set of sequential rules based on the species likely to be present to assign the chemical components of a sample to their respective mineral components. The dominant sulfide mineral assemblage present at Hera is galena, iron-bearing sphalerite, chalcopyrite, pyrrhotite and pyrite. A normative technique for estimating the relative abundance of each of these species from drill hole, grade control and metallurgical assay data sets has been developed. This includes a process for deriving a gangue iron value and differentiating pyrrhotite from pyrite using sulfur/iron ratios. A calculated total sulfide volume value has been utilised at the mine to improve interpretation of lode boundaries. Normative drill hole values have also been used for domaining within the orebody, with large scale mineralogical trends evident. Dry bulk density (BD) values calculated using a normative species-weighted method show good correlation with measured BD values (R2 = 0.895) and are a significant improvement on the Pb+Zn+Cu regression method (R2 = 0.646) previously used. Application of these calculations to identify errors in assay databases is demonstrated, with specific reference to the data set for the nearby Nymagee copper deposit. Validation of block model grades is also explored and a method to improve resource estimates using direct normative mineral interpolation is proposed. The integration of the normative data into the production and metallurgical data sets at Hera is described and the relationship of the normative minerals to other economic elements such as gold and silver is discussed.CITATION:McKinnon, A R, 2017. Application of normative ore mineralogy to geological and metallurgical data sets at the Hera Au-Pb-Zn-Ag mine, New South Wales, Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 63–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By J A. Cowburn

The high intensity zone within the Jameson Cell is the downcomer. It is largely external and separated from the flotation tank. This, together with operation of the downcomer under vacuum, rather than at elevated pressure and the absence of moving parts, allows ready access to the high intensity zone for measurement and analysis. Experimentation was conducted allowing measurements of recovery for residence times of between 20 milliseconds and ten seconds within the downcomer of a Jameson Cell. The affect of aeration rate on the recovery of different particle sizes was also studied.

Jan 1, 2005

Role of Bubbles in the Action of Flotation Agents

Sep 13, 2010

By J Franz, S Bock, N Hentrich

Artificial ground freezing is the unrivalled method for groundwater control during mine shaft sinking. Moreover, ground freezing may also provide temporary ground support. The fast development of fibre-optic temperature monitoring devices, three-dimensional freeze pipe survey methods and numerical modelling software provide grounds for developing new and reliable tools for ground control during freeze shaft sinking. This paper presents examples of predictive numerical models that are based on back-analysis and calibration of temperature data that covers the complete construction cycle from pre-freezing through to artificial thawing. The back-analyses showed that standard numerical models are not capable of predicting the prevailing thermo-mechanical conditions satisfactorily. This paper describes the development and implementation of new tools for improved consideration of concrete hydration and latent heat, along with the introduction of other algorithms that improve and simplify the efforts of managing complex numerical models. A function is presented that allows for an automated correction of the model’s mesh based on results of three-dimensional freeze pipe surveys. This paper demonstrates that the latter consideration is important, because the often employed assumption of idealised freeze circle geometry in numerical models impacts on the accuracy of such model’s predictions. Subsequently, the verification of these extended numerical models is demonstrated. Due to its flexibility, the FLAC3DTM code was employed for the numerical modelling. This software provides the possibility of implementing additional functions written in internal FISH or Python language into the models. It is concluded that state-of-the-art techniques for freeze hole drilling and surveying, on-site monitoring and advanced numerical analysis provide a significant potential for both the design and the operation of largescale ground freezing measures. The application of the extended numerical models for predictive simulations during construction allows for temporary shaft lining optimisation, for assisting in operational decision making and for compensating temporary loss of monitoring data. Suggestions are made for required future work in order to further improve the developed ground control tools. CITATION:Bock, S, Franz, J and Hentrich, N, 2018. New tools for ground control in freeze shaft sinking, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 393–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Frothing in Seawater Flotation Systems

Sep 13, 2010

When the mining and milling of 1100 copper orebody commenced at Mount Isa a satisfactory grade of copper concentrate was difficult to produce. The major concentrate contaminants were fine pyrite and silica, particularly in the minus 10 microns fraction. Studies of the 1100 orebody showed that much of the fine grained pyrite and a proportion of the silica present in the ore contained carbonaceous matter in the form of complete or partial rims and as internal carbon films disseminated throughout grains. The hydrophobic surface property of the carbonaceous material resulted in inherently flotable fine pyrite and siliceous particles.The addition of a 60:40 mixture of nigrosine and dextrine, initially to a prefloat concentrate of the inherently flotable carbonaceous material and finally to the total copper flotation feed, successfully controlled the flotation rates of the carbonaceous pyrite and silica. The objective of a 25 per cent Cu concentrate grade was then achieved without decreasing copper recovery.

Jan 1, 1971

By B Mack

The cost of water treatment is now more than ever a major consideration for maintaining an environmentally and economically sustainable mining operation. As an industry, we often have to consider water sources that are highly impure and difficult to treat. We are also discovering the value of our waste waters in this regard and using new and improved methods and technology to reclaim and reuse water. In many instances, the water or waste water to be treated is highly acidic and saturated in sparingly soluble salts. Conventional systems used to liberate this type of water typically involve high doses of lime with large volumes of waste sludge produced, and are comparatively complex to operate, to pretreat the water in order to reduce scaling tendency on the reverse osmosis stage. However, if the water is considered valuable for reuse, then why not avoid difficult and cumbersome pretreatment processes and treat the water at low pH to keep the sparingly soluble salts, metals and other dissolved species in solution. This paper describes a patented technology that uses and successfully proves this concept as a cost effective option for certain situations. Results from a treatability study on an Australian groundwater are discussed, along with an economic comparison to a conventional method and discussion on full-scale potential.

Jan 1, 2009

By P M. Black, T Itaya

Arc-type volcanic activity has been a major feature of the late Cenozoic geological evolution of the Pacific-Australian plate boundary in the northernNew Zealand region. The time/space distribution patterns of arc-type rocks reflect changes in the nature of the plate boundary as it has evolved. Inception of volcanism began in the north during earliest Miocene times (26 Ma) following ophiolite emplacement and during the next 10 Ma developed into a volcanic arc segment extending south to the present position of the central North Island. The northern part of the arc became extinct about 15Ma ago, but activity continued in the central (Coromandel) part of the arc until about 5 Ma ago. In late Pliocene and Quaternary times volcanic activity has become concentrated in a northeast trending zone which is collinear with the Tonga-Kermadec Arc.   These time/space patterns can be interpreted in two ways. Firstly, if relative plate motion was essentially transform in the region prior to 26 Ma then a small change in the relative plate vectors may have initiated subduction and the associated volcanism. Southward evolution of the arc can then be seen as the straightening and extension of a single arc. Alternatively, the distribution of volcanic rocks can be interpreted as the capture of a relatively short lived arc by southward migration of the dominant Tonga-Kermadec subduction system.

Jan 1, 1995

The highland region of Papua-New Guinea is relatively rugged terrain where stream gradients are steep. In areas where porphyry copper deposits outcrop the streams commonly expose primary sulphide mineralization in unoxidized rocks. Stream sediment geochemistry combined with float examination and broad geological mapping proved to be an effective tool for detection of outcropping bodies of mineralization. After discovery, detailed stream sediment sampling, soil sampling and rock chip sampling, together with detailed geological mapping proved adequate to delineate drilling targets. Reconnaissance stream sediment sample density was dictated by geology and access and a density of one sample per 25 Km2, or less, was desirable to ensure a high degree of confidence in the programme. Research indicated that the base metals occur in sulphide form in stream sediment and that the -80 mesh size fraction gave the most reliable results. The evaluation of results from any one area relied on the interpretation of the local geology. Basic histogram methods for determining background and threshold values for metals in stream sediments were

Jan 1, 1973

By N Weatherstone

A consistent and reliable international approach to public reporting of a mining companyÆs main assets, its Mineral Resources and Mineral Reserves, has become of increasing importance in recent years with the rapid globalisation of the mining industry. Through the efforts of the Committee for Mineral Reserves International Reporting Standards (CRIRSCO), a committee representing national resource/reserve reporting committees in Australia, South Africa, UK/Ireland/Western Europe, Canada, USA and Chile, the reporting standards in most æwesternÆ countries use almost identical resource and reserve definitions and are generally around 90 - 95 per cent compatible. New codes based on the CRIRSCO model are being developed or considered in other countries, including Peru and the Philippines. This unified approach has provided the mining industry, regulators and investors with a common framework to report and interpret mineral resource and reserve estimates, thereby facilitating funding to the mining industry through improved investor understanding and confidence. The common reporting standards are reflected in the CRIRSCO International Template, available on CRIRSCOÆs web site, a document that is kept æliveÆ by reflecting the best of the most recently published CRIRSCO-type national standards. In a significant exception to this unified industry approach, the USA Securities and Exchange Commission (SEC) requires adherence to its own standard, only partly compatible with CRIRSCO-type standards, with adverse and costly implications for companies listed in the USA. A major industry submission was presented to SEC in April 2005 which, if accepted, would bring about considerable compatibility of CRIRSCO and SEC standards. The UN Economic Commission for Europe (UN-ECE) has, since 1992, been developing its Framework Classification (UNFC) as a single global system for harmonising all existing national and international resource/reserve reporting systems, covering both government and industry requirements and both the hydrocarbon and solid minerals sectors. While few mining companies report their resources and reserves using the UNFC, the system is accepted or is being examined as a basis for reporting by some governments, including those of Russia, China and India. The UN-ECE agreed in 1999 to incorporate CRIRSCO definitions into the UNFC for those categories of resources and reserves used for market-related reporting, but a more recent edition of the UNFC removed or changed the definitions, requiring re-engagement by CRIRSCO to ensure compatibility. Since 2005, CRIRSCO and the Society of Petroleum Engineers (SPE) have been involved in discussions with the International Accounting Standards Board (IASB), which plans to develop a new Accounting Standard for the Extractive Industries as part of its International Financial Reporting Standards. At the request of the IASB, CRIRSCO and SPE have been examining any potential for convergence of resource/reserve definitions between the mining and hydrocarbon industries. Each of these systems is described in this paper and high level comparisons made.

Jan 1, 2006

By L Lachance, F Flament, D Leroux, S Gariépy

The pervasiveness of poor sampling practices in and around mineral processing plants could seem intriguing in view of the various documented evidences both for causes and consequences. To this extent, this paper revisits the well-documented but lesser-known fact that failure to care sufficiently about how samples are selected and managed is the mother source of almost all sampling biases. The authors believe that the potentially huge leverage between causes and consequences as well as the diversity of people involved in sampling call for a globally integrated solution rather than for a point solution. Such a globally integrated solution has already been put forward by the AMIRA P754 Metal accounting – code of practice and guidelines (AMIRA, 2007) that inherently requires accuracy to be targeted, measured, reported and managed. Furthermore, always in order to avoid a point solution, several layers of protection against biases must be put in place with each one involving a different ownership whenever possible. This is exactly the role intended by the supervisory bias detection method described in this publication. It is based on the continuous monitoring of the expected value of reduced residuals obtained from statistical data reconciliation conducted in a metal accounting context. This supervisory bias detection method is developed in full details after which Monte Carlo simulations are done on a mineral processing plant example for showing how it can be successfully applied for detecting hidden biases.CITATION:Lachance, L, Leroux, D, Gariépy, S and Flament, F, 2014. Detecting sampling biases in metal accounting, in Proceedings Sampling 2014 , pp 109–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

In the last few years it has become legal for women to work without restriction underground in some States in Australia. Since the mid 1970's there have been women graduates in mining engineering from several Australian tertiary institutions. Women from this group are the first females to have been employed to do manual work underground this century. The questions which arise are "What are the current parameters surrounding the employment of women underground?" and "What have been the experiences of those women who have worked underground?". In order to answer these questions, contact has been made with the various mining schools in Australia, the relevant government departments, the main underground mining companies, the relevant unions and professional associations, and other women who have worked undergrond. Personal experience as both a miner and a mining engineer at the CSA Mine near Cobar in New South Wales is also used.

Jan 1, 1988