Search Documents

By B McFadzean, N P. Lima, D A. Deglon

The reverse flotation of Itabirite iron ore is typically performed after a desliming step in which most of the sub-10 µm particles are removed. This is done to limit processing problems such as poor flotation recovery of SiO2 due to slime coatings and increased slurry viscosities, unmanageable froths and increased losses of hematite particles due to entrainment. However, the rejection of ultrafine particles contributes to large losses in iron recovery and may contribute to the instability of tailings dams. The aim of this study is to decouple the effects of ultrafine particles in the pulp and froth phases to better understand the processing capabilities of the fines fraction. The flotation test work was performed in a special-purpose continuously operated laboratory flotation cell that has a deep froth section to simulate plant-scale froth conditions. Five conditions of fines addition were investigated at three different froth heights and a solids concentration of 50 per cent. The behaviour of the pulp and the froth were decoupled using froth stability and froth recovery tests. This showed that, even though there is an exponential increase in froth stability at increasing fines quantities, the performance of the pulp has the overriding effect on the overall SiO2 recovery. Pulp zone, froth zone and overall SiO2 recoveries showed that overall recoveries increased by about 3.6 per cent for every 1 per cent decrease in fines content. This meant a large increase of 20 per cent in SiO2 recovery when going from undeslimed to deslimed feed. This was driven largely by increases in the pulp zone recoveries, which were about 4 per cent for every 1 per cent decrease in fines content. The froth recoveries, on the other hand, decreased by between 0.75 per cent and 2.5 per cent for every 1 per cent decrease in fines content, depending on froth height. This paper explores further insights into iron ore flotation processing at different slimes concentrations.

Aug 24, 2022

By Glastras M. V

The presence of arsenic in solutions which result from the processing of many sulphide minerals leads to a need to understand its speciation in aqueous systems and the reactions of those various species. This paper deals in particular with the precipitation of arsenic from aqueous solution in the form of insoluble inorganic compounds in order to remove arsenic from various hydrometallurgical process streams. The solubility and stability of the precipitates is examined. It has been found that many of the arsenic compounds presently used are more soluble than previously accepted and unstable in disposal sites such as tailings ponds.

Jan 1, 1987

In November, 1967, a four strand curved mould continuous casting machine coupled with a 50 ton basic oxygen furnace began producing billets for the rod mill and new merchant mill at the Newcastle Steelworks. To date over 500,000 tons of carbon and alloy steels have been cast at the rate of 20,000 tons per month, the major part for the wire industry. Many alterations have been made to the plant to simplify the process, improve quality and increase production. Casting parameters have been developed for each different type of steel. The quality of the final product has been influenced most by casting temperature, secondary cooling and casting speed. All these factors have been controlled and good results are reproduced. More exacting requirements of liquid steel quality have brought about the use of higher lime/silica ratio slags during steelmaking to control phosphorus revers- ions and standard ladle additions of manganese suicide and ferro aluminium for more effective deoxidation.

Jan 1, 1972

By J Naude

The TauTona (Sotho for Great Lion) Mine near Carletonville, which is one of AngloGold AshantiÆs most profitable operations in South Africa, has started a multi-million dollar expansion project that is expected to extend the operational life of the mine by at least three years. The project will also secure some 1900 jobs for existing workers and contract workers. The $US140 million project entails the development of the orebody to a record depth of almost 4 km underground. It means that TauTona, which already mines gold at the deepest levels in the world, will deepen its mining activities from 3600 m to a new record depth of 3910 m. There is great anticipation about the expansion program, especially because of new technology that will contribute to a safer working environment. It includes a simplified hoisting system that will minimise safety risks in conveyance activities. Due to the unique nature of this project, depth below surface and working through a three-tier shaft system, various innovative measures were incorporated into the planning of the endeavour. Special support equipment was designed to reduce cycle times and enable the crews to install the extensive support, prescribed by the mineÆs rock engineering department, right up to the face before every blast. Both declines dip at 23¦. The personnel/material (P/M) shaft is 4.4 m wide x 3.9 m high. This shaft is unique in that the conveyance will have an onboard driver. The rock shaft is 4.5 m wide x 3.6 m high. Rock will be hoisted with two, ten-tonne overturning skips. In both cases, P/M and rock, the winders were designed for the highest duty cycle, which is encountered during sinking.

Jan 1, 2005

By D Liang, L Zhang, X He

The sulfurisation-flotation process was unsuccessful when initially applied to the oxidised Pb-Zn ore in Lanping County of Yunnan Province China. A comprehensive mineralogical study indicates that the problem is caused by the soluble salt gypsum in the Lanping oxidised ore, which produces a large amount of Ca2+ cations. The Ca2+ cations react with S2- anions (from sodium sulfide) in preference to Zn2+ and Pb2+ forming calcium sulfide, and make it difficult to form zinc and lead sulfides on the surfaces of the respective oxidised Zn and Pb minerals. In addition, the calcium sulfide formation consumes a large quantity of the available sodium sulfide, further inhibiting the sulfurisation process. The efficiency of the sulfurisation of oxidised Zn and Pb minerals has been improved greatly by the pretreatment removal of gypsum, with the added benefit of the required dosage of sodium sulfide being substantially reduced.

Jan 1, 2008

By B T. Park, S D. Fundingslan, K W. Wangerud

The EPA National Risk Management Research Laboratory (NRMRL) Mine Waste Technology Program (MWTP) and the EPA Region VIII Superfund office are jointly conducting a field-scale technology demonstration of a two-step in situ treatment of the acidic Anchor Hill Pit lake at the Gilt Edge Mine Superfund site near Deadwood, South Dakota, USA. The project goal is to develop cost and performance data for the in situ treatment for potential application in long-term water treatment/management activities at the Gilt Edge site, and for potential application at other similar sites. Lime neutralisation of the pit using a Neutra-Mill was accomplished in the spring of 2001, with a resultant lime utilisation efficiency of about 71 per cent, and a typical throughput of about 1 tonne per hour using coarse, pebble quicklime and 1.4 tonnes per hour using finer, ground lime. Redox-mediated biotransformation treatment of the pit has been ongoing since May 2001. As of January 2003, denitrification is complete in the near-surface waters and about 90 per cent complete in the deeper waters. Bacterial sulfate reduction is expected to begin in the near future. This paper describes project activities, results, and lessons-learned to-date as well as future monitoring plans.

Jan 1, 2003

By Cai S, Zhou C

The requirement of mineral resources is increasing as the economy is continually increasing in China. The mining practices of various complex sulphide deposits and precious metal deposits, and the treatment of mine tailings and other industrial solid wastes, have greatly improved fill quality in the metal mines. From early-1980s, high density slurry fill, paste fill of total tailings, low density slurry fill with addition of silicate gelling agent, etc has been studied and applied, and some progress has been achieved. Today, mine tailings, slag and power plant ash are widely used as fill materials in mining. A number of cemented fill mines equipped with large capacity trackless mining machines are in production. Recently, The 3rd Chinese National Symposium on Mining with Backfill, 1995 has been held, the progress of fill technology in mines has been exchanged and summarised. In the paper, some aspects of fill technology used in the metal mines of China are briefly introduced and some applications of fill research work are presented.

Jan 1, 1998

By T Mahlangu

The leaching of gold in alkaline aqueous cyanide solutions may be reduced significantly by the passivation of the gold by a surface layer of polymeric aurocyanide. This passivation of the gold is typically countered by the presence of Pb(+2) species in solution, which may be present as an impurity in the solution, or specifically added for this purpose. The speciation and availability of Pb(+2) in typical cyanide leach solutions is illustrated as a function of pH, and the presence of S(-2), S(+6), Cu(+1) and Ag(+1) species. The probable role of the Pb(+2) species in efficient gold leaching is discussed.

Jan 1, 2007

By Parker C. J, Mikula P. A

The excavation for the Sydney Opera House Parking Station comprises a large donut shaped underground cavern with a central sandstone pillar. The maximum effective roof span is about 19 m and the rock cover is between 7 m and 8 m. Permanent support for the roof and the various services tunnels consists of a combination of tensioned anchors, and untensioned dowels, and mesh with shortcrete and fibrecrete as the final lining. Steel sets were installed at main intersections.Fundamental to the design philosophy for excavation of these spans at such shallow rock cover was the use of monitoring to check on the adequacy of the installed support. Prior to excavation, extensometers, inclinometers, piezometers and surface settlement survey stations were installed. Underground survey stations, anchor load cells and shotcrete pressure cells were installed as excavation proceeded. Excavation commenced at the crown using an initial heading and three widening stages. Geological mapping during excavation confirmed borehole expectations, namely sandstone beds 1 to 4 m thick interbedded with thin shale units. Bedding plane contacts varied over short distances from tight partings to thick brecciated seams. Jointing was subvertical and joints tended to be bed-limited.

Jan 1, 1993

A new classification of subduction related (epithermal- / mesother-mal) gold mineralisation styles based on the tectonic framework they occur in, has been found helpful in practice. It offers a ratio-nalisation of exploration efforts during all stages of work.Methodology on the ground during first pass- and follow up explo-ration which has been found effective for the various mineralisa-tion styles is being briefly outlined.

Jan 1, 1990

By S R. Grano, M Vera

This paper deals with two separate case studies investigating the froth phase performance and characterisation of two industrial rougher/ scavenger flotation circuits. Froth phase performance was quantified using a mass balance approach to estimate froth zone recovery. Measured characteristics of the froth phase included frother solution concentration determined by gas chromatography, and the time taken for an equilibrium froth sample to decay to one-half of its original froth height. The latter measurement is referred to as the æfroth half-lifeÆ and is strongly linked to froth stability. Special methods and techniques developed to preserve frother in solution and to measure froth half-life are briefly described. The frother type in the first case study was a mixture of straight and branched alcohols, whilst the frother type in the second case study was a mixture of alcohols, aldehydes and triethoxybutane. The first case study focussed on a flotation circuit treating a low-grade ore containing only a small fraction of floatable copper sulfide minerals, while the second case study focussed on a flotation circuit treating a higher grade complex sulfide ore containing significant quantities of chalcopyrite, galena, sphalerite and pyrite. It was found that froth zone recovery of valuable mineral generally decreased down-the-bank of the two industrial rougher/scavenger circuits. Moreover, decreases in froth zone recovery significantly limit the overall cell recovery of valuable mineral achievable from the plant scavenger cells. However, the decrease in froth zone recovery could not be linked to the removal of frother from the pulp solution to the concentrate product in the preceding rougher flotation stages. Measurements of residual frother in solution suggested that, approximately, only five to ten per cent of the added frother was removed into the rougher/scavenger concentrate, with the remainder appearing in the scavenger tailings. This finding suggested there was apparently adequate frother in solution in the scavenger stages.

Jan 1, 2005

By Fraser RJ

A Robbins Raise Drill Model 61R was used to provide one 7' diameter shaft 1050' deep in Clutha Development's exploratory mine at Blackwater in Central Queensland and two 7' diameter shafts 1450' deep at their South Clifton mine on the Illawarra Coast of New South Wales.

Jan 1, 1972

The Ida Valley in Central Otago is one of series of parallel basins filled with freshwater sediments. The basins are in fact tectonic depressions superimposed on NE trending grabenlike structures which occur in the area and are the result of block faulting possibly initiated in Cretaceous times and concluded in late Tertiary and early Quaternary. In Central Otago this tectonic event affected metamorphosed rocks belonging to the eastern facies of the New Zealand Geosyncline and collectively known as the Haast Schist Group. These rocks constitute the basement and the shoulders of the tectonic depressions. The Ida Valley occupies the depression wedged in between the Raggedy Range to the NW and the North Rough Ridge in the SE. The valley is approximately 38 km long, 3 to 7.5 km wide and is drained by the NE flowing Pool Burn, which meets the SW flowing Ida Burn. The resulting unified stream flows into the Manuherikia river which drains the next door depression to the NW. The present work deals with the Ida Valley basin and more specifically with the geology studied within two Prospecting Licence areas held by Gold Mines of NZ Ltd on the southeastern flank of the valley.

Jan 1, 1977

The global economic, political, sociological, and technical environment has become extremely volatile and unpredictable. Price and demand patterns for fuel and non-fuel minerals have become highly variable. Increasingly militant environmental movements now have a material effect on the price, cost and availability of energy sources and indirectly also on non-fuel minerals.The pace of political change in the U.S.S.R., Eastern Europe, and China has accelerated. Western Europe, Japan, and the U.S. are reacting to these changes with varying degrees of confidence or timidity.Technical and economic developments continue to have a substantial effect on the fortunes of the mineral industries. However, they are increasingly influenced by social and political factors. Supply, demand, and trade patterns in the Pacific Rim Region will continue to be influenced by developments in other regions, such as southern Africa

Jan 1, 1990

By A Maurer, N Pereira

Low-density explosives have been developed with trials being conducted for over 20 years and yet have still only gained limited market acceptance despite producing some very promising results. The biggest concern with industry acceptance has been disbelief that a product with lower density than the ANFO benchmark could fragment anything but the weakest of strata. Trials have been carried out with products such as diluted ANFO, low-density ammonium nitrate (AN) and various other mixes, although it has been only recently that low-density explosives have been accepted as a serious alternative to traditional products such as ANFO and heavy ANFO. The recent uptake of low-density products has been the result of several key factors: the current resources boom forcing AN supply issues, the development of new handling techniques, and a far better understanding of the utilisation of such products. This paper highlights the benefits of low-density products available in the market and focuses on the situations where low-density explosives can provide the end user with benefits that would otherwise be achieved through more time consuming methods. Through correct implementation, low-density explosives can provide the blast designer with another option when looking at the optimum method of breaking the rock. This while still controlling the other limiting factors such as cost, environmental impacts (noise, vibration, dust and fumes), coal damage and safety (stable walls).

Jan 1, 2005

By K S. E, S C. Parker, T K. Kundu

Understanding the fundamental principles governing the reactions at surfaces has always been the goal of theoretical surface science. The atomistic simulation techniques have been used to calculate the surface structures and the stability of quartz and wollastonite, and their adsorption behaviour in the presence of molecular and dissociative water, and the two widely used collector head group molecules of methanoic acid and methylamine. The dissolution behaviour of wollastonite has also been modelled. The calculated surface energy, hydration energy and reaction energy values have been examined and discussed in the light of flotation literature. These studies have given an insight into the interactions at atomic level, which indicate that modelling techniques should be capable of predicting the adsorption behaviour and to design the selective collector molecules, which is of central importance to the mineral processing technique of flotation.

Jan 1, 2005

By Heinrich CA, Wall VJ, Walshe JL

The Porgera Gold Mine, located in the highlands of Papua New Guinea, has produced over 5 million ounces of Au, since its opening in late 1990. The deposit is located within Upper Cretaceous Papuan Platform sediments approximately 25 km south of the Lagaip Fault, and is spatially and temporally associated with the 6 Ma alkaline Porgera Intrusive Complex.

Jan 1, 1995

By C M. MacRae

The characterisation of high-P iron ores by field emission gun electron probe microanalyser (FEGEPMA) was carried out to determine elemental associations in iron oxides sensus lato and, using this knowledge, to speculate on possible P incorporation mechanisms in goethite. Quantitative data was collected from two goethite-rich bulk ores and results showed that in both samples goethite was the main repository for phosphorus. The P-rich goethite also contained elevated levels of both aluminium and silicon.To understand the mechanism of P incorporation in goethite, high-P grains were located by coarse mapping of polished blocks with the FEG-EPMA. Analysis of element distribution maps collected on the P-rich grains showed that low-P regions within grains were typically associated with low-Al and high-Si, whereas high-P regions were associated with high-Al and low-Si. Based on follow-up quantitative analyses, a coupled substitution mechanism for phosphorus incorporation within goethite was proposed: 2Si4+ = 1P5+ + 1Al3+. Additional quantitative analyses on further examples indicated the mechanism was only valid for Si contents in goethite of <1 wt per cent.Preliminary transmission electron microscope (TEM) studies confirmed the presence of P, Al and Si in goethite.

Jul 11, 2011

The Barmac autogenous crushing mill is one of the most successful new comminution technologies to become available to the mining and industrial minerals industries in this decade.The Barmac autogenous crushing mill is an innovative Vertical Shaft Impactor which operates in essence like a high intensity dry ore centrifugal pump with the reduction occurring primarily as a result of high velocity rock to rock impact in a fully rock lined crushing chamber. With applications in a wide range of mining and industrial minerals operations the Barmac autogenous crushing mill presents an opportunity to enhance reduction and liberation whilst providing many cost savings and production increases in new and existing plants.This paper briefly describes the operation of the Barmac autogenous crushing mill and reviews its benefits.

Jan 1, 1990

This paper deals with the extension of Post Office telecommunications (telephone, data, leased private lines etc.) network to mining communities in remote areas of Australia. The evolution of the "Spur Line" policy and its application is referred to together with comments on the engineering of telecommunication Facilities.

Jan 1, 1973