Search Documents

This paper traces briefly the reasoning which led to the decision to extend the existing internal shaft at the Rosebery Mine and to instal underground a larger winder (No. 2 Hoist) with capacity to handle all hoisting requirements to a depth of approximately 2,500 ft. on an incline varying from 83" to 55" to the horizontal. It then covers the specifications and selection of the winder, the design of the winch chamber, rope raise and bins, the excavation, support and lining of the chambers and the transport to site and installation of the machinery. Finally a brief description is given of the mechanical and electrical parts of the winder.INTRODUCTIONThe existing shaft winder on the internal inclined shaft situated on No. 8 Level of the Rosebery Mine had reached the limit of its capacity. Hoisting 21-ton capacity skips in balance, with a 13/16-in. diameter rope, it required four layers of rope on the 3 ft. 6 in.drums to reach the loading station under No. 12 level at a depth of 864 ft. (Fig. 1). This entailed heavy wear on the multi-layered rope and heavy stresses on the cheeks of the drums. Continuous working on three shifts was necessary to handle ore, men and materials, and a hold-up from any cause whatever meant an interruption to production on the lower levels of the mine. The maximum output of the hoist whilst hoisting from the No. 12 level loading station was 50 tons per hour. It was obvious therefore, that a larger winder was required if output was to be maintained.Diamond drilling had proved the existence of sufficient ore at depths well below No. 12 to warrant exploitation and a decision had to be reached on the means of hoisting this ore.

Jan 1, 1958

By McDougall I, Claoue-Long J

A combination of high precision 40Ar/39Ar and U-Pb dating has been used to determine the age of hydrothermal minerals and host rocks in a number of Lachlan Fold Belt (LFB) gold deposits in New South Wales, Au4 ralii In particular, this investigation demonstrates that the UAr/ Ar technique of K-Ar dating can be used to determine the timing of mineralization in Palaeozoic systems.A close temporal link between mineralization and Late Ordovician to Early Silurian magmatism is indicated by the dating work. Hydrothermal sericite from the Goonumbla p8rph gy Cu deposit and Glendale Au prospect yieldsAt/ Ar step heating ages between 437.9 ¦ 1.1 and 441.2 ¦ 1.1 Ma (16), and4 minjrnum age of about 425 Ma has been obtained by Ar/ Ar dating of hydrothermal amphibole from the Browns Creek Au-Cu skarn deposit. Hydrothermal aluniI8 frog the Gidginbung epithermal Au deposit yields reset 44 Ar/ Ar ages of 401.0 ¦ 1.3 to 417.3 ¦ 1.3 Ma (16). U-Pb dating by ion microprobe on magmatic zircons from the vicinity of the Goonumbla and Gidginbung deposits gives ages of 438 ¦ 3.5 Ma (2 6), and 435 ¦ 2.5 Ma (2 (7) respectimly, W a minimum age of 435 Ma has been obtained by Ar/ Ar dating of magmatic phases from volcanic rocks adjacent to the Browns Creek skarn deposit. Magmatic episodes near the Sheahan-Grants gold skarnpost give ages of 479.2 ¦ 1.1 and 467.9 ¦ 4o1 by 'Ar/ 9Ar dating of magmatic amphibole. Most Ar/3yAr age spectra show the effects of partial Ar loss at between 360-420 Ma, probably due to heating caused by granitoid emplacement.The radiometric dating work in this paper suggests a restricted metallogenic epoch in the Late Ordovician-Early Silurian LFB, NSW, of similar duration to that found in the Andean margin and the western Pacific island arcs around the Pacific Rini.

Jan 1, 1990

By Giles C. N, Loughnan F. C

Bentonites and active earths from N.S.W., previously analysed with respect to occurrence, mineralogy and physical properties have been evaluated for use as bonding agents in quartzose moulding sands in terms of green properties and behaviour both with and without coal dust for iron castings poured at 1400°C.INTRODUCTIONIn the paper by Loughnan .and See (Part I) the occurrence, mineralogy and physical properties of the fuller's earth and bentonites of New South Wales were discussed and it was shown that some of the materials approached the quality of Wyoming bentonite. In the present paper the same samples from Marulan (Bl), Boggabri (B2), Wingen (B3), Muswellbrook (B6), Swansea (B8), Dubbo (89) and Trida (Bll) have been investigated with respect to their potential value as bonding agents in compounded moulding sands. Inaddition, the -20 micron fractions of the Boggabri (B2t) and Swansea (B8t,> were recovered and the former converted to a sodium clay, in order to assesE; the beneficiation possibilities. A sample of Wyoming bentonite (S2) also has been included for comparison.GREEN PROPERTIES OF THE ARTIFICIAL MOULDING SANDSA quartzose base sand (Botany Dune) previously oven pried and screened to 1·65 mm., was subjected to a sieve ana]ysis in accordance with standard A.F.A. practice to yield a calculated' fineness number of 45. All tests were carried out on mixtures of this sand with2t per cent clay, since such mixtures were found most suit...

Jan 1, 1959

By J Mauk, R Ruddock

The Taharoa ironsand deposit is 1600 hectares in size and is located 144 km south of Auckland on the west coast of the North Island, New Zealand. The sand predominantly contains heavy mineral-rich sediments, quartz, and feldspars. One hundred and two samples were collected from all areas of the mine, from the stockpile, black sand areas, tailings and Te Akeake Sands. Samples were collected with the primary focus on the next predicted mining path and secondly on gaining a good geographic spread throughout the mine. All samples were analysed for the dry, wet and particle density, the porosity and the magnetic, non-magnetic and clay minerals content.Stockpile samples had an average magnetic mineral content of 92 percent. Dry, wet and particle density values for stockpile material exceed all values from untreated ironsand samples with average values of 2.8g/cm3, 2.9g/cm3 and 4.4g/cm3 respectively. Black sand samples from the mine came from various areas such as the central area, the forest, the southern area and the benches. All black sand samples are remarkably consistent, with dry and wet density values between 2.3 û 2.5g/cm3 and particle densities that range from 3.7 to 3.9g/cm3. The porosity values are comparable to all other areas of the mine (average 37 per cent). The tailings and Te Akeake Sands have different physical properties due to their different mineral contents. The dry, wet and particle densities are all lower than that of all other areas with averages of 2.1g/cm3, 2.2g/cm3 and 3.3g/cm3 respectively. These lower values reflect the lower magnetic mineral content (average 18 per cent) and the associated increase in non-magnetic mineral content (average 78 per cent).

Jan 1, 2002

Interest in the sampling of refined copper cathodes has heightened over the last ten years. This has followed the increasing importance of cathodes as the principle trading form for metallic copper. It has also been given impetus by recent trends for quality certification of manufacturing inputs, specifically the AS3900 and IS09000 series of standards.

Jan 1, 1976

This paper presents results of the experiments carried out in Beth Energy No. 33 Mine for the purpose of alleviating problems associated with cutter roof. Cutter roof problems have delayed the advance of the entry development considerably and maintenance cost of these entries was very high due to the requirement of very extensive and heavy artificial supports. The study includes assessment of the problem, investigation of the geology and lithology of the mines, study of in-situ stresses and corrective measures to combat the problem. Two approaches were selected as the corrective measures: 1) implementing yield pillar concept in order to reduce the effects of in-situ horizontal stresses, 2) designing an effective roof reinforcement system and application procedure. Results of this study revealed that roof strata is weak and in-situ stresses are very high at the problem area which results in development of cutter roof. Implementation of yield pillar concept was found to be ineffective because cutter roof often developed at the entry face concurrent to the development. However, proper design and implementation of roof reinforcement system stabilized the roof and eliminated roof caving during both entry development and retreat of longwall face, despite existence of the cutter roof, at a much lower cost.

Jan 1, 1992

By Pitkajarvi J

Waste rock dilution causes mill feed grade to be lower than mineral resource grade. In nickel mines relative grade decrease (dilution) may be tens of per cent because of irregular ore boundaries and weak wall rocks. Five per cent dilution costs millions of dollars annually in medium size underground mine. In Outokumpu Group selective bench and fill stoping, cable bolting/shotcrete-skin support and fast ore boundary definition (OMS-logg in-hole logging or sludge sampling) are the key tools in dilution control. Commitment of the whole organisation to keep dilution low is also needed. Dilution sources and effects are discussed with examples of the dilution control methods applied in Outokumpu mines.

Jan 1, 1996

By G W. Scott, H M. Lukey

The Lake Superior Region has been a producer of iron ore for over 150 years. Early mining operations concentrated on direct shipping ores, which are the result of post-depositional upgrading principally by deep weathering. As direct shipping ore reserves became depleted, the focus changed to the production of iron ore pellets from taconite. The post-depositional processes responsible for upgrading taconite are regional metamorphism, contact metamorphism and hydrothermal processes (Clout and Simonson, 2005). While these processes are important in iron ore genesis they can also contribute to liberation problems and in some instances reduced pellet quality (Han, 2004). Low-grade metamorphic mineral assemblages can negatively impact liberation and pellet quality. Low-grade iron formation may contain a suite of carbonate minerals including ankerite, dolomite, kutnohorite, siderite and magnesiosiderite. Variation in the distribution and composition of siderite and magnesiosiderite makes controlling the MgO content of pellets difficult. Carbonate minerals also require calcination in the pellet induration process, which requires additional heat to be added to the system, slowing down the induration process and reducing throughput. Prediction of carbonate mineralogy and carbonate mineral chemistry is an important goal of ore characterisation for pelletising properties. Contact metamorphism causes changes in mineralogy and grain size (Klein, 1973; Gunderson and Schwartz, 1962). Increasing the grain size of magnetite should improve its liberation characteristics. However, plant grinding targets may not allow the coarse-grained, more easily liberating magnetite ores to increase throughput and can actually result in decreased throughput due to recirculation. While magnetite and martite ores are well understood (Lukey, Johnson and Scott, 2007) late open-space filling microplaty haematite ores are not. These ores, while composed of similar minerals, have a unique genesis that results in fine grain size and complex textures that present liberation challenges and often make interpreting laboratory metallurgical test results more difficult.

Jan 1, 2007

By T Martin, M Martin

Mining of sulfide-based ore deposits typically creates a potential for release sulfate and acid to groundwater, and many operating mines are thus predicted to require long-term post-closure treatment of groundwater. Toward the goal of selecting an optimal treatment, this paper compares costs of four demonstrated technologies for long-term treatment of sulfate-contaminated groundwater: in situ biological reduction (ISR), in situ permeable reactive barrier (PRB) composed of compost and zero-valent iron (ZVI), and two ex situ æpump-and-treatÆ technologies ù ex situ biological reduction, and ex situ nanofiltration with lime precipitation. Costs for each technology are estimated for treatment of a model aquifer system containing sulfate-contaminated groundwater, with the goal of treating 1 m3/min of groundwater from 1500 mg/L sulfate to a target level of 500 mg/L. (Metal removal is typically achieved by these technologies, and thus excluded from this analysis.) Costs are estimated for each technology as a function of treatment duration (ten to 60 years) and, for PRB and ISR, required replacement frequency (ten to 60 years). Estimated costs include capital and operation and maintenance, using a seven per cent net discount rate. Results indicate that ex situ technologies (biological reduction and nanofiltration with lime precipitation) are the most expensive. In situ technologies may be much less expensive, with PRBs having by far the lowest potential cost, followed by ISR as the next least expensive. However, actual costs for the in situ technologies are very sensitive to poorly constrained parameters, particularly the ZVI content of the PRB, and the effective life of PRB and ISR systems. This large cost uncertainty supports delaying remedial actions where viable, and suggests that feasibility analyses are generally warranted for specific applications to focus on these sources of uncertainty.

Jan 1, 2003

By DiStefano AB, Dale SG

This paper describes the laboratory study implemented to investigate the application of the subaerial technique to tailings disposal for the proposed Olympic Dam Mine. The results of the study and the resulting design parameters are presented. The subaerial technique of tailings disposal is described and the advantages of the method for disposal in arid climates highlighted.

Jan 1, 1984

Don Hausen was a pioneer in the field of quantitative mineralogy. Methodology that he developed at Newmont almost 40 years ago is still employed today, only the technology has advanced. Petrographic methods were stressed with an emphasis on alteration, mineralisation and paragenesis. Methodologies employed by Don on the Carlin deposit were applied to developing the Carlin Trend by helping to work out lithology and structure, which ultimately led to the discovery of deep high-grade deposits. Quantitative methods used by Don on San Manuel, Copper Creek and Superior, Arizona were applied to the development of the Batu Hijau Deposit in Indonesia. Advancements in technology since DonÆs time have made the mineralogist much more efficient. Manual measurement of peak heights off of strip charts for semiquantitative XRD has been replaced by software that does Rietveld refinement and whole pattern fitting. Hand contouring of XRD data has been replaced by digitised data incorporated into geologic models. Optical point counting, which would take a dayÆs work to process 1000 points, has been replaced by automated SEM methods where 20 000 points are possible in an hour. The use of the optical microscope remains relatively unchanged, and still remains as Don emphasised the æeyesÆ of mineral exploration. However, the information can be relayed much more quickly with digital image capture and electronic data transfer. Don insisted on becoming involved in projects at the grassroots level and supporting the project through mine closure. This made the mineralogist a liaison between exploration geologists, mine geologists, metallurgists and mine engineers. The methodology that Don helped develop continues to provide invaluable support to Newmont geologists and metallurgists worldwide today.

Jan 1, 2008

By S Vink, V Nanjappa, C J. Moran

Poor quality water resulting from interaction of surface run-off with saline mine spoil and soils can cause significant problems for water reuse on mine sites. Not only can this saline water lead to machine corrosion and increased maintenance costs, but may cause detrimental effects on the environment. Determining the geochemistry of mine spoil, and the likelihood of salt dissolution during rainfall events, may aid in more effective mine site management of water. Spoil samples were taken from three areas of the German Creek mine site, situated in the Bowen Basin coalfield, Queensland. Samples from two undisturbed areas on the lease were also collected for comparison. Analyses were performed using a variety of laboratory techniques: leaching tests, effective cation exchange capacity determination, X-ray diffraction, clay quantification, and total organic content determination. Results show that dissolution of surface (top 2 cm) salt minerals from spoil areas is an important contributor to surface run-off salinity during rainfall events. Equally, ion exchange with clay minerals appears to be a significant source of elevated ion concentrations in run-off waters. Findings from the undisturbed areas show undetectable quantities of salt mineral species, resulting in waters with low ion concentrations. More generally, monovalent cations (sodium, and to a lesser extent potassium) appear to be derived from dissolution of salt precipitated whereas divalent cations (calcium, magnesium) are more likely to be sourced from exchange reactions with clay minerals. Incorporating knowledge about the mechanism of cation mobilisation from spoil with the spatial distribution of spoil properties and understanding of the dynamics of water quality variations on the site will aid in development of integrated water quantity and quality management strategies.

Jan 1, 2009

By G K. Robinson, M D. Sinnott

Three-dimensional granular flow models have been run to simulate three types of sample cutters: a cross-stream cutter, a vezin, and a cross-belt cutter. This type of modelling involves solving the equations of motion for large numbers of individual particles as they travel along a conveyor belt and interact with a sample cutter. It allows flows of bulk materials to be visualised and understood. Here we have used spherical particles. These results illustrate some advantages that modelling has compared to physical bias testing: By taking reference samples which are very close to the actual samples, the estimation of bias can be achieve quite precisely with very few runs. (Many Standards about bias testing recommend a minimum of 20 runs, but we have found that five runs generally provide adequate precision.) Potential bias can be divided into two components: the particles which are missed but should have been sampled and the particles which are extra but which should not have been sampled. This more detailed information can provide useful insight. Exactly the same material can be sampled using different sample cutters, thereby avoiding a source of variation that complicates physical testing. Much more detailed visualisation is possible, allowing better understanding of the bulk material flow in various circumstances.

Jan 1, 2005

This paper describes the programing and specification requirements which affected the choice of excavation methods on the Melbourne Underground Rail Loop (M.U.R.L.). The various methods that were chosen are briefly described, and the three most used are compared in more detail. Excavation rates, cycle times and other statistics are compared for full face tunnel boring, full face drill and blast, and heading and bench using a road header excava- ting machine. The length of tunnel excavated is sufficient to enable meaningful statistics to be presented and the significant specifi- cation and geological factors are described to weight the statistics where necessary for purposes of comparison. Average tender prices are given for excavation and primary support to indicate the reimbursement sought by contractors to carry out this type of tunnelling.

Jan 1, 1981

By S Hille, J Karageorgos

With the increased variability of todayÆs large-scale mining operations, consistent flotation performance is important to improving and sustaining overall recovery through the circuit. The Newcrest Telfer Mine has implemented advanced process control technology to obtain stable level operation and consistent mass pull in the copper rougher and scavenger flotation circuits. The final result has been an overall reduction in variability, which impacts on both copper and gold recovery. This paper describes the methodology and implementation of the improvements in control at the Newcrest Telfer Mine as being an essential part of the business for minerals processing.

Jan 1, 2007

By D Eschebach, D Mathewson

A belt press filter (BPF) handbook containing practical information for the reference of plant designers and operators has been created as part of Australian Coal Association Research Program project C23040. The handbook combines research and experience with newer generations of equipment and circuitry. BPFs are increasingly finding application in the dewatering of thickener underflow tailings slurries due to changing environmental regulations, difficulty obtaining tailings storage facility approvals and limited water availability. Sources of BPF inefficiency and low availability stem from a lack of understanding of the key operational parameters that affect their performance. This lack of understanding typically leads to increased operational expenditure due to suboptimal reagent dose rates and increased maintenance costs, or decreases in plant availability due to excessively high filter product water contents and equipment failure. It is essential for the continued economically competitive operation of Australian coal handling and preparation plants that complex factors affecting BPF operational performance are clearly defined and understood. Installation and operation handbooks are often provided to sites with new installations, but these manuals are manufacturer- or even model-specific and are often focused on mechanical maintenance. The handbook identifies industry ‘best practice’ and improvements developed by other sites, such as extra spray bars, air system bleed valves, guarding designs, feed and filtrate protection screens and roller tensioning systems. Equations to predict optimum operating conditions – such as free moisture, belt tension and reagent dose rates, with simple feed-specific variable inputs – have been developed from site-specific test work. The correlations developed provide a benchmark for plants to attempt to achieve. This provides operators and process engineers with a tool to explain BPFs and assist them in optimising the performance of BPF dewatering plants of both contemporary and less modern design.CITATION:Mathewson, D and Eschebach, D, 2015. ACARP belt press filter design, operation and maintenance handbook, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 73–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

Gallery Stoping, an old but little used stoping method, has been reintroduced to workings at the Paringa South Shaft.Orebodies which are amenable to such a method are being mined in this manner with considerable advantages and savings.The advantages of gallery stoping as used at Paringa, compared with traditional mining methods are:1. constant cash flow2. low set up cost and initial stope development3. nearly 1005 recovery 4. no access problems 5. quicker tonnagesAs compared with highly mechanized mining methods, it has been found to be slower but requires less development, gives improved grade control, has less impact on the surrounding rock and fragmentation is much better, reducing secondary blasting costs.This paper examines the mining method and illustrates the advantages of gallery stoping at Paringa.

Jan 1, 1985

The word `environment' may have many different meanings but, for the purposes of this paper, I have assumed the definition included in the Environmental Protection Act 1986 (Western Australia). This Act defines `environment' as `... living things, their physical, biological and social surroundings, and interactions between all of these'. The Act further defines the `social surroundings of man' as `... his aesthetic, cultural, economic and social surroundings to the extent that those surroundings directly affect or are affected by his physical or biological surroundings'. This gives a very broad meaning to the idea of environment and environmental issues, and it is therefore understandable that the influence that environmental issues have on mining activity can vary so much from state to state, and even within states, and why the degree of influence can change so much with time.

Jan 1, 1990

By M Barker, H Li

The total number of tailings accidents has reduced from over 50/decade in the 1960s-1980s to less than 30/decade in the 2000s to 2010s. However, the rate of significant tailings dam failures has not been reduced. The significant tailings dam failures the mining industry experienced in the recent history include: Merriespruit, South Africa, 1994; Los Frails, Spain, 1998; Kolontár, Hungry, 2010; Mount Polley, Canada, 2014; and Samarco, Brazil, 2015. The conventional Factor of Safety approach itself may not be enough to further reduce the rate of significant tailings failures due to its limitations such as uncertainty. For example, the same factor of safety could have a vast range of annual probability of failure for different tailings dams, and insufficient consideration of failure consequence. This paper presents a risk based approach for design with the objective being to minimise tailings dam failures, especially those significant tailings failures with high consequence and low probability. This approach includes risk based design and risk management using bowtie tools. In the risk based design, quantitative analysis will be used to estimate the annual probability of failure and the tolerable failure criteria is linked to the consequence category. Bowtie analyses will be used to understand hazards and risks and identify and select independent controls that are effective in preventing and mitigating catastrophic failures. In this paper, examples of risk based design and bowtie analyses are presented and discussed. CITATION:Li, H and Barker, M, 2018. Risk-based approach for minimising tailings dam failures, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 397–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By J J. McNee and, J Crusius, T F. Pedersen

The use of water covers is a globally-applied method for minimising acid rock drainage (ARD) and metal leaching. Although the subaqueous disposal of potentially acid-generating materials has been shown to effectively limit ARD, under certain scenarios, metal remobilisation can occur at circum-neutral pH. The following paper presents data from four case studies in which metal mobility from submerged mine waste resulted in degradation to water quality in the overlying water cover. Subcentimetre resolution profiling of dissolved constituents across the tailings-water interface (dialysis arrays), in conjunction with mineralogical information, were used to elucidate the controls governing metal mobility. The data illustrate four pathways of metal remobilisation, including: the release of zinc via the oxidative remineralisation of metal-rich organics at the tailings-water interface; enhanced remobilisation of arsenic as a result of anthropogenic eutrophication; the release of copper resulting from the pH-driven dissolution of treatment sludges; and the release of radium from uranium mill tailings due to the dissolution of radiobarite [(Ra,Ba)SO4] by sulfate-reducing bacteria. The results highlight the conclusion that the chemical stability of submerged tailings reflects both: the solid-phase characteristics of the tailings material; and the physical, chemical and biological characteristics of the depositional environment. In particular, the data illustrate that rigorous characterisation of both the waste solids and receiving environment must be performed in order to assess their compatibility. The results have relevance to the management of tailings repositories including constructed impoundments, pit lakes and natural lakes.

Jan 1, 2003