Search Documents

By N Lewis

Recent major urban trunk sewer infrastructure projects in Melbourne have involved construction of nearly 10 km of tunnel boring machine (TBM) driven tunnels in a range of geological conditions varying from soft alluvial soils to hard volcanic rock. To provide both construction and permanent access to the new trunk sewer network, a total of 17 shafts between 5 m and 13 m in diameter, and up to 64 m in depth have been constructed. This paper describes the design and construction of the temporary shaft support systems for the shafts.The range and variability of geological conditions at each shaft site required the adoption of the following shaft support systems across the projects – jet grouting, sheet piles, diaphragm wall, secant pile, contiguous pile, reinforced shotcrete rings and rock bolts.Groundwater control, settlement, TBM launch and reception chambers at the shaft base, chambers and TBM launches at mid-depth of shafts, connection shafts between new and existing sewers and bypass pumping shafts are among the challenges that have been met.This paper reports on the some of the challenges involved and experience gained in developing design and construction solutions for large diameter shafts that are excavated within varying geology in Melbourne over the past three years.

Mar 8, 2011

By L P. Gray

"From paving the way in gaining approval for the first metalliferous in-pit tailings storage facility (TSF) in Victoria, to developing a deposition methodology to optimise the storage capacity and provide a final rehabilitated surface which replicates the premining topography, in-pit tailings storage has proven not only to be a cost-effective means for tailings management at Fosterville Gold Mine, but also one which provides significant economic, social and environmental benefits. Coupled with ongoing raising of the existing above ground TSF and commissioning of a new above ground TSF, Fosterville Gold Mine have to date effectively used three open pits for in-pit tailings storage, with one of the pits currently progressing through the capping and vegetation establishment phases of closure.This paper presents the process adopted by Fosterville Gold Mine in their flotation tailings management, from design and operational phases through to rehabilitation implementation. Included within the paper are challenges which have arisen during the process, and a discussion on principals behind the designs and lessons learnt during operation of the facilities.Citation:Gray, L P, 2016. Full Cycle Tailings Management at Fosterville Gold Mine, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 369–378 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M R. Drumond

The present work presents a new theoretical interpretation of the flotation process, which can also be applied to other mineral processing physical unit operations. This interpretation is part of the æModelo OperacionalÆ (Operational Model) that was developed as an attempt to establish a new theoretical basis for mineral processing unit operations. In the case of flotation, a book was edited by one of the authors in Brazil (Mass Concentration by Froth Flotation, in Portuguese and Spanish).The model establishes a link between a natural phenomenon (migration of particles from the pulp to the froth) and a real industrial phenomenon (mass concentration by operational interference). In this model, flotation is viewed as a phenomenon of macromolecular mass transport (of particles) between froth and slurry phases. Mechanisms for mass transport and particle flow between phases as a function of the hydrophobic potential in each phase are discussed. By establishing the so-called equilibrium distribution curve between phases it is possible to calculate macroscopic balances that are related to metallurgical results, which in turn are a function of the operational line that is required by the process itself. The number of cleaning stages and their efficiencies can also be determined by simple laboratory-scale experiments.

Jan 1, 2005

By J Euston

In the 1990s round flotation tanks were introduced as a result of the lower fabrication costs for larger cells. It was soon observed that round tanks held a number of further advantages over the traditional rectangular cells, such as better hydrodynamics, lower costs and reduced footprint per unit volume.In the last twenty years flotation cell sizes have increased almost exponentially and designs of 250 to 300m3 are a well established standard with plans for full scale pilot installations of 500m3. The option to install these large cells gives flexibility in circuit arrangements and allows efficient and economic matching of flotation lines with modern mill designs. The benefits of scale up are well known with reduced numbers of cells required, lower power costs per unit volume, etc. These benefits will be briefly reviewed with specific reference to the installation of 300m3 to 350m3 flotation cells at the Copperton Concentrator of Kennecott Copper in Utah, USA.The sophisticated techniques required to model these ‘supercells’ have led to a critical review of the fundamentals of flotation science and engineering. In addition to outlining the advantages of large flotation cells, this paper will review the science which supports, and occasionally challenges, the ongoing trend to larger flotation cells.

Aug 8, 2011

By R Moreby, J Kok, L van den Berg

The high production rates achieved from mass mining methods such as block caving, sublevel caving and longwall mining require large conveyor belts, trucking loops (diesel/electrical) and rail systems for ore handling. However, the ore handling systems used in mass mines introduce a significant amount of heat into the overall ventilation system, which may be problematic at depth or in mines located in hot climates.In particular, the heat load from a conveyor system is not always well understood and consists of various components, including frictional heat from idlers, heat from electrical motors, heat from the drive train and heat from broken rock transported on the conveyor system. This paper presents results from a study that investigated the heat introduced to the ventilation air from a large conveyor system. The conveyor system transports ore with a maximum virgin rock temperature of 41°C from a depth of over 1 km. Air, belt and rock temperatures were measured in the conveyor system to evaluate the distribution of heat loads.CITATION:van den Berg, L, Moreby, R and Kok, J, 2015. Heat load estimation from conveyor systems in mass mines, in Proceedings The Australian Mine Ventilation Conference, pp 63–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By V Pere

A geotechnical data management system has been developed to manage drillhole and mapping data generated from in house and consultant administered field programs. This system comprises a data collection interface with integrated validation, processing and reporting functionality. Development of the database required careful consideration of how and what geotechnical information is gathered in the field, a clear understanding of the interdependency of the parameters, and the outputs required to support geotechnical design.The acQuire Geoscientific Information Management System was selected as the preferred software to support the process because of its ability to easily manage data from capture in the field through to quality reviews and ultimately into reports. Initially only geotechnical logging of diamond core was considered, subsequently the system has been expanded to support additional geotechnical data sources such as laboratory test results, traverse and window mapping data. This paper focuses on the core logging data acquisition, validation, analysis and presentation of data.The acQuire Geoscientific Information Management System has proven to be a robust platform for the capture, interrogation, and reporting of geotechnical data. Data entry objects have been created to manage seven different areas of geotechnical data collection ranging from core logging to mapping to automated reports for falls of ground.

Aug 22, 2011

By S Dunham

For decades we’ve been focusing on reconciliation as a tool to validate mineral resource estimates. And for decades we’ve been misleading ourselves. The concept of reconciliation is simple. Predict, measure, compare and assess the quality of the prediction. This four-step process reflects the ideas of statistical process control and the plan-do-check-act cycle of Shewhart and Deming fame and our intuitive understanding of using system feedback to improve performance. In an ideal world where data is robust and dense this type of feedback loop can be useful. In the mining industry however, there are some fundamental flaws with the conceptual framework. At almost every stage of the process from pre-estimation through to final production the mining system is plagued by material challenges with data and measurement quality and quantity, system delays, and losses from a supposedly closed system. These issues can and do impact on the benefits sought from reconciliation. Instead of providing feedback leading to improved estimation, reconciliation can result in poor decisions, distracting investigations, and exacerbate the noise in an already noisy system. Before we can rely on reconciliation as a management tool, we need to address the multiple challenges present in our everyday practices. Some of the most critical issues are addressed in this paper.

May 24, 2023

By D Wimpenny

Underground infrastructure is often a critical component of transportation and utility schemes. It is characterised by long design lives with limited access for inspection and maintenance. The exposure environment can be difficult to assess since it will often vary substantially between different locations in the same facility and with time during construction and in service. In addition, the specific demands placed upon underground infrastructure are not well covered by the exposure classes and other guidance given within current codes of practice. When problems occur they can be difficult to rectify and involve significant disruption.Given these substantial risks the prudent designer may adopt a systematic ‘durability planning’ approach which:· defines the environment and principal deterioration mechanisms for the various elements and construction materials,· predicts the design life for alternative durability enhancement options, and· recommends associated measures to be adopted during construction and in service.This paper describes the development of durability planning within Halcrow, giving examples of its use from its first implementation on tunnels under the Suez Canal in 1993 to recent projects in the Middle East and Australia. It seeks to demystify the process, identify shortcomings and speculate on its future development within the civil and mining sectors.

Mar 8, 2011

By C Dick

Over the past three decades, mining operations have seen a significant increase in the use of contractors for mining, camp management and catering, recruitment, maintenance, power management, and commissioning. More recently contractors have been engaged for stores and logistics, OH&S, environmental, exploration, training etc. In some countries, such as South Africa, the trend is towards total outsourcing of all aspects of a mining operation which is coordinated by the owners’ management team.During the Global Financial Crisis (GFC) more Australian companies considered and/or took on this approach to recruiting for both projects and operations as mining companies were forced to rethink their corporate strategies as commodity prices plummeted to low levels, pushing operations and projects into potentially financially unviable territory.This paper discusses the labour recruitment, commissioning and operating strategy of Western Areas NL (WSA), with the assistance of Independent Metallurgical Operations Pty Ltd (IMO), as it progressed construction, commissioning and operation of the Cosmic Boy nickel concentrator at the Forrestania Nickel Project during and post GFC. The use of IMO contractors allowed Western Areas to mitigate labour cost risk during the uncertainty caused by the GFC and let their management team focus on the task of bringing a new operation into viable and profitable production.

Aug 8, 2011

By Harrison AT, Smart RM

Backfill systems using unconventional cementitious hinders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: 1. A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings 'stable' slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 in high and the tailings were relatively high in pyrite. .\ GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shnnkage). The system used a slurry, but the addition of the ;iutivator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: ò sloping widths (mining heights) above 1.6 in; and ò shaft pillar removals in seismically active areas at the end of the life of the shafts. \This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems).

Jan 1, 1998

By A Clarkson

Cannington Mine is an underground silver lead zinc operation located in north-west Queensland which has been in production since 1997. Ore is primarily moved through an underground material handling system comprised of a crusher, conveyor and hoisting shaft. The Fowler Shaft was constructed in 1997 using a strip and line method with the intent for it to provide a means to hoist ore from the loading station 600 m below surface. The shaft also serves as the route of key services including high voltage power, mine dewatering and fresh air. Despite the adherence to a mining exclusion zone, large-scale change in geotechnical conditions around the shaft were first observed in 2015. Ongoing ground movement around the shaft lead to cracking and delamination of the concrete liner. Shaft management required the on-site team to measure deformation rates and magnitudes, forecast change, manage rockfall risk and deforming pipework, and ultimately, hoisting skip clearance. Monitoring techniques to observe and measure deformation were required to evolve with the magnitude of movement. Some techniques leveraged off modern technology while some of the most useful techniques were based on logic and first principles. All shaft deformation management strategies relied on the co-operation and alignment between Cannington’s Infrastructure Maintenance, Survey and Geotechnical Departments.

Mar 29, 2023

By C Rule

In 2003, Anglo Platinum, in a joint development with Xstrata Technology, installed the world’s first 10 000 litre IsaMillTM in a concentrate regrind duty at the Western Limb Tailings Re-treatment Plant. The success of that installation was the enabling event for Anglo Platinum to proceed with a substantial investment in horizontal stirred milling technology. Since 2006 an additional three IsaMillsTM in concentrate regrind duties and a further 18 IsaMillsTM in the more technically challenging coarse grinding mainstream applications, have been commissioned in group Concentrator operations - bringing the total number of IsaMillsTM installed in Anglo Platinum plants to 22.A collaborative approach between Anglo Platinum and Xstrata Technology towards improving milling efficiency and reducing operating costs, through internal mill component wear optimization and operating recipe development, has resulted in further improvements in the overall success of IsaMillsTM in the flow sheets of many Anglo Platinum operations. The addition of IsaMillsTM in the Anglo Platinum flow sheets has improved plant PGM recoveries by as much as 5%.This paper explores the improvements made to the IsaMillsTM flow sheet and mill internal design and shares some of the operating experience with IsaMillsTM technology in Anglo Platinum

Aug 8, 2011

By S Hapugoda, Y Tang, L Lu

The steel industry is one of the global leading CO2 emitters, accounting for approximately 7 per cent of global anthropogenic CO2 emissions. In 2022, the world produced 1878.5 Mt of crude steel. About 70.8 per cent of the world’s crude steel was produced by integrated steel mills through the blast furnace and basic oxygen furnace (BF-BOF) process, while the remainder was produced largely by mini mills using electrical arc furnaces (EAF). Compared with gas-based DRI and scrap-based EAF processes, the direct CO2 emissions from the BF-BOF process and the coal based DRI and EAF process are significantly more, as both the processes rely heavily on fossil fuels, such as coke and pulverised coal, to provide energy and reduce iron oxides. Hydrogen is very reactive and reduces iron oxides to metallic iron without generating CO2. Therefore, substitution of hydrogen for fossil fuels in these processes presents a good opportunity to significantly decarbonise the steel industry. This paper will first discuss the thermodynamic and kinetic characteristics of hydrogen and carbothermic reductions of iron oxides and then examine the behaviours of different ore types present in Australia iron ores during hydrogen reduction.

Sep 18, 2023

By P Klaric

Drive stability is critical in block/panel cave mining. The production levels of these mines are required to remain operational for the entire life-of-mine which can be in excess of 30 years. It is therefore necessary to produce high-quality drives to ensure sustainable mine productivity. In order to improve the quality of drives and pillars, this gold mine instigated a project to optimise their development blasting. The initial aim was to reduce the level of overbreak in development mining, which was averaging approximately 18 per cent. The benefits of controlling overbreak not only included an increase in the integrity of the drives but also a decrease in load and haul and ground support costs. Through focusing on the optimal blasting of the perimeter holes, overbreak was reduced to 4.5 per cent. The project’s focus then moved to drill and charge designs for development faces. In optimising these designs, it was anticipated that improvements in the development mining cycle would be achievable.CITATION:Klaric, P, 2015. Improving drive stability through efficient development blasting design and practices, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 327–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Late Cretaceous and early Tertiary coals in the Greymouth, Ohai and Kaitangata coalfields represent a major national energy resource comprising-up to 2500 x 106 tonnes of coal in ground. The three coalfields are closely related in terms of age and sedimentary and structural character. The most striking feature common to all is the complexity of the geology which has severely restricted exploration and mining of these coal resources. This complexity is manifest in the irregular lensoid nature of coal seams and by the incidence of unpredictable medium and small scale faulting and folding. There are many geological similarities between these coalfields which are considered to arise from a common origin which can be related to the plate tectonic evolution of the southwest Pacific region. In order to efficiently assess and exploit these coal resources it will be necessary to know their geology in great detail. This can he achieved by increasing the understanding of the sedimentary and structural evolution of the coal bearing basins. This knowledge may be gained by the application of traditional (ie drilling, field mapping) and innovative techniques (ie high resolution seismic, in seam seismic) with on going research-oriented studies (ie basin analysis, coal petrography).

Jan 1, 1987

By T Dawson, B Haskins

Fatigue is it the newest buzz word or is fatigue a real phenomenon that is creating safety and organisational risk for you? There is no debate that fatigue is natural, and it affects us all, just like gravity; however, there has been much debate on the severity of its impact in the workplace. For many years the impact was not measurable, hidden out of sight and, quite frankly, written off as the infamous ‘operator error’. Over the last several years, advancements in technology have provided safety and health professionals, sleep scientists, fatigue experts and organisations with the ability to monitor and detect fatigue events in real time, as well as predict and monitor increased risk for fatigue events. Caterpillar Safety Services has assembled an extensive and exceptional set of technologies that will provide the best methods and data to measure the impact of fatigue. This paper will discuss fatigue in the workplace and review the technologies and data sets available, which will allow the reader to determine whether this risk is real or rubbish.CITATION:Haskins, B and Dawson, T, 2017. Fatigue risk in your operations – real or rubbish? It actually depends , in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 137–142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By A H. Bagherieh, S Mesroghli, H Jorjani, S Chehreh Chelgani

The rare earth elements (REEs) assay and recovery in leaching processes is being determined using expensive analytical methods, ICP-AES, and ICP-MS. This paper presents a neural network model to predict the effects of operational variables on the lanthanum, cerium, yttrium, neodymium recovery in the leaching of apatite concentrate. The effects of leaching times: ten to 40 min, pulp densities: 30 to 50 per cent, acid concentrations: 20 to 60 per cent and agitation rates: 100 to 200 rpm were investigated and optimised on REEs recovery in laboratory at a leaching temperature of 60¦C. The obtained data, on the laboratory optimisation process were used for training and testing of a neural network. A feed-forward artificial neural network with 4-5-5-1 arrangement, was capable of estimating the REEs leaching recovery. Neural network predicted values were in good agreement with the experimental results. The correlations of R = 1 in training stages, and R =  0.971, 0.952, 0.985 and 0.98 in testing stages were results for Ce, Nd, La and Y recovery predictions respectively and that theses values are considerably acceptable. It was shown that the proposed neural network model accurately reproduces all the effects of operation variables, and can be used in the simulation of a REEs leaching plant.

Jan 1, 2008

By P Khalkho, M Singh

Rock masses when subjected to uniaxial or triaxial cyclic loading (eg in hydraulic running tunnels, during retrieval and injection of oil and gas from storage underground caverns and haulage roads), the material has a tendency to fail in fatigue. In order to design safe and reliable underground structures, the determination of brittleness under such loading conditions becomes a pre-requisite. Brittleness influences strongly the failure process and makes the rock mass behaviour complex under different tunnelling and mining activities. Brittleness Index is a term to quantify the brittleness feature of a specimen. In the present study, an attempt has been made to quantify the brittleness of jointed specimens using different brittleness criteria. The joints of the model jointed specimens were oriented at an angle of θ=15° normal to the loading direction, each having three different JRC’s=2–4, 12–14 and 14–16. The specimens were tested under triaxial conditions in incremental complete cyclic test scheme performed at displacement-controlled mode. Different brittleness criteria were used ie stress-strain dependent brittleness index, Young Modulus approach and energy-balance based mechanism. It was observed that energy-balance based mechanism which consider the post failure behaviour is more descriptive to reflect the whole variation of brittleness from sheer brittleness to ductility.

Nov 29, 2022

By Frfas C, Parrilla F, Regife J. M

A project to develop the Zinclor electrowinning cell to industrial size is being conducted at Tecnicas Reunidas' Research and Development Centre with Spanish Ministry of Industry support. This project is the final development phase in zinc electrowinning from a chloride medium, the highest ZINCLOR technology development level prior to the industrial scale having already been reached. This paper covers the outcomes and conclusions corresponding to project Phases 1 and 2: Process Selection and Industrial Electrodes (1 m2) design and testing. The most important achievement reached is that there are presently available industrial cathodes and anodes for the Zinclor diaphragm cell giving an optimum response for zinc chloride electrowinning with unit power consumptions between 2.65 and 2.80 kWh/kg Zn, depending on the diaphragm type. Standard electrolysis conditions were: 65 g/L ZnC12, 3 g/L HCl, 160 g/L NaCl, 350 g/t Zn arabig gum as the addition agent, 36¦C, and 400 A/m2 current density. The selection of electrodes, diaphragms and organic additives for the industrial scale tests have been optimised. The complete electrowinning cell development, with electrodes having an active area of I m2, enables the evaluation of Zinclor Technology application for industrial processes.

Jan 1, 1993

Tertiary laterite is extensively developed in the Darling Range area, but there is doubt that. the high relief areas along the Darling Scarp have been peneplaned. Three distinct laterite types are distinguished which are termed transported, introduced and residual laterites to avoid ambiguity. Transported laterites are recemented (primarily) lateritic materials and introduced laterites are chemical deposits of bog iron type. Residual laterites are formed in situ from the host material which can be either decomposed bedrock or detrital' clay, and the two varieties formed from these sources are termed residual A and residual B laterites. The genetic requirements for residual laterite formation are (1) host material, (2) porosity and permeability, (3) rainfall, (4) temperature, (5) relief and drainage, (6) vege- tation and (7) time. Previous theories on the origin of laterite appear to be inadequate and incompatible with field observations. Field investigations and drilling in the Darling Range area disclosed lenticular section and thickest laterite development on slopes and thin or oc- casionally no laterite development on crests. Lateritisation is considered a surface feature and the end product of the chemical weathering cycle. The relief and rain-water acting on a kaolinitic host material are con- sidered the major contributing factors in the

Jan 1, 1973