Search Documents

This paper investigates dry drilling as a feasible alternative to meet current requirements for improvements in mining productivity in an increasingly competitive world.A field test program was conducted in the surface facilities of a hard rock mine in Sudbury, Canada, to investigate the potential use of dry drilling in underground bulk mining as a conceivably faster and more economical method than wet drilling. The test work consisted of the monitoring of advance rates and bit life while a series of 165 mm diameter holes, wet and dry, were drilled with compressed air at both mine (0.69 MPa) and high (1.72 MPa) pressure levels. The results indicate that penetration rates can be increased by approximately 24 per cent by drilling dry with high air pressure and by approximately 27 per cent by drilling dry with mine air as compared with wet drilling under the same conditions. Dry drilling also has the effect of increasing bit life by up to 69 per cent. An economic analysis for typical hard rock mines indicated that drilling productivity and cost savings can be increased by approximately 23 per cent when dry drilling is utilised.The testing program indicates that dry drilling has the potential to become a feasible technique with regard to performance, productivity and costs.

Jan 1, 1991

By A Fareth

Constructed between 1885 and 1891, the New Croton Aqueduct (NCA) in New York State is a 50 km long (31 mi) brick-lined tunnel conveying water from the Croton watershed north of New York City to distribution systems in the Bronx and Manhattan. Except at two siphons, the aqueduct operates as an open channel conduit from the New Croton Reservoir downstream 39 km (25 mi) to the Jerome Park Reservoir in the Bronx. The remaining 11 km (6 mi) is operated as a pressurised conduit and includes a major siphon, of circular cross-section, under the Harlem River. The aqueduct has a flow capacity of approximately 1100 million litres of water per day (13 m3/s or 290 million gallons per day) and supplies on average ten per cent of New York CityÆs drinking water. The CityÆs water supply system is operated and maintained by the New York City Department of Environmental Protection (NYCDEP). This paper covers the work done during the three main stages of the program to rehabilitate the entire NCA: inspections, design and rehabilitation. It also includes some of the more interesting structural findings of the original construction as well as documents and drawings from the NYCDEP archives. The rehabilitation program has been underway in phases since 1993, with inspections scheduled to minimise outages, allowing this strategic aqueduct to remain in service during critical seasonal periods. The open channel flow section of the aqueduct in the north is horseshoe shaped, with inside dimensions of 4.1 m (13.6 ft) in width and 4 m (13.5 ft) in height. The pressurised section is 3.7 m (12.3 ft) in diameter, and includes a 90 m (330 ft) deep siphon under the Harlem River. A total of 163 million bricks were used in the construction, enough to build a 48 km (30 mi) wall around Manhattan Island, 3 m (10 ft) thick and 15 m (50 ft) high.Between 1993 and 1997 a series of in-tunnel investigations were performed in the open channel portion of the NCA, consisting of field inspection, non-destructive geophysical testing, and coring of the brick liner. Between November 2004 and September 2005, a major inspection program was conducted to assess the condition of the 11 km (6 mi) long pressurised section and all shafts, headhouses and blow-off structures along the entire 50 km (31 mi) alignment. Inspection methods included using an underwater remote operated vehicle (ROV) equipped with sonar and cameras to inspect the deep siphon, fibre optics examinations of probe holes drilled through and beyond the brick lining, and core holes and geophysical inspections to assess properties of the liner and behind-the-liner materials. A water pressure and test grouting program was conducted to assess methods and expected grout takes for the rehabilitation work in the pressurised sections. The rehabilitation program is anticipated to be completed in 2010.

Jan 1, 2008

Fine Gravity Separation in the Reflux Classifier, Exploiting a High Shear Rate, Laminar Flow Mechanism The Reflux Classifier is used in the gravity separation of particles over a broad range of particle sizes. The device consists of a fluidised bed zone, with a system of parallel inclined channels above. The inclined channels provide a significant hydraulic advantage over conventional fluidised beds via the so-called Boycott Effect (Boycott, 1920). This paper describes a new advance in fine gravity separation based on the high shear rate and laminar flow profile that arises when closely spaced inclined channels are deployed. As reported recently (Galvin et al, 2009a), a powerful density based separation mechanism develops from this arrangement, suppressing the effects of particle size. In this paper we focus on two areas, firstly the application of the separator in the laboratory for batch fractionation of particles of varying size and density to determine the grade recovery curve and hence the liberation, and secondly the step change in separation performance achieved on a continuous steady state basis when closely spaced inclined channels are used. The variation in the separation density with particle size decreases significantly, and the Ecarte Probable Error (Ep) remains at low levels over a broad size range.

Sep 13, 2010

By P B. Hills, R J. Walton

Narrow vein tabular orebodies are prone to mining induced seismicity. The Tasmania Mine is a complex example of a seismically active tabular orebody, where the contrasting material properties of the host strata and of the orebody itself, serve to exacerbate the seismic response. Analysis of a continuous record of seismicity over a period of seven years has provided significant insight into the fundamental mechanics of the rock mass. Understanding seismicity to permit safe extraction of the orebody has been enhanced by instrumentation of rock mass behaviour in response to mining and mining induced seismicity. It is the purpose of this paper to explore that understanding in respect to the adoption of an alternative down-hole Avoca stoping method for use in particular circumstances.Intensive instrumentation of the Tasmania Mine over a period of four years has provided insight into the behaviour of the rock mass in response to extraction of the narrow vein orebody it encompasses. A range of instruments have been installed in clusters or single installations in order to measure changing stress conditions and the impact of those changes on the rock mass and the reinforcement system.Instruments are often installed in very close proximity to active production stoping. While it has been possible to observe the impact of the mining and mining induced seismicity at very close quarters, instruments installed in these locations are vulnerable to damage and consequently, the level of instrumentation is high. Instruments are continuously logged, typically on a six hourly basis coinciding with the end of regular blasting times. The response of the instrumentation to changed rock mass conditions is considered against the background of development and production blasting and against the seismic record to assess the viability of downhole Avoca stoping.CITATION:Hills, P B and Walton, R J, 2012. Continued observations of rock mass behaviour in response to stoping at the Tasmania mine, Beaconsfield, Tasmania, in Proceedings Narrow Vein Mining 2012 , pp 169-178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

I would like to build on the keynote address given by Peter Stoker to the Fourth International Mining Geology Conference (2000) entitled æThe Role of the Mine GeologistÆ. He concluded that à the important aspects of the professional contribution of a mine geoscientist to a mine operation include: The geoscientists prime task is to maximise the profitable extraction of the ore deposit on which they are working û that is to add value. They must maintain and develop their own expertise. By ensuring a truly professional approach to all they do, they will provide the best service to the community, to their company or client, their shareholders and their family or close associates. In that process they will also assist in protecting themselves in this increasing litigious world. I intend to build on these points and, in particular to expand on what it really means to take a truly professional approach to mine geology. Mine geology is different from other forms of geological practice. As a mine geologist you are the advocate for the orebody. After all the orebody is the one thing that is unchangeable.

Jan 1, 2003

By Naik J. S G

The plant practice plays an important role in production and productivity. Men, material and machinery have to be judicially utilised to achieve maximum output with minimum cost. Improvements in technology should be incorporated at an appropriate time and place. The personnel concerned should be properly trained and motivated to receive the changes in machinery and technology. Strict adherence to prescribed parameters, optimum utilisation of man, machinery and operating supplies help in the smooth functioning of the plant and in achieving maximum gains.

Jan 1, 1992

By Longworth C. R

This paper descrioes a case history of a coal mine which developed un'tahle roof conditions due to mass sliding of the overburden strata on a claystone band within the coal seam. The sliding is believed to have been initiated by stress relief associated with the removal of overburden alongside the entry portal of the underground workings. Once in motion, the roof block was kept moving by bulking due to roof collapse in the normal underground goafing operations. Control measures in the form of an earth and rockfill buttress against the entry portal and a sequential mining plan to create goaf areas alongside the entry portal have been initiated to attempt to limit movement. The operation has been continually monitored and a gradually decreasing pattern of movement is being re, orded.

Jan 1, 1981

The Department of Mineral Resources is the lead agency in mine site environment management and control inNew South Wales. The Department introduced a Mining, Rehabilitation and Environmental Management Plan (MREMP) process several years ago in order to integrate the activities of other government agencies who may have a material interest at the mine site. The MREMP process has resulted in a spirit of trust and co-operation between agencies and between agencies and mining companies. The spirit of co-operation has been reflected in greater public confidence that mining is environmentally responsible.  

Jan 1, 1995

By P Landeros, D Benado, J Cornejo, A Pinochet, C Caviedes

In 2005, El Teniente mine began preconditioning the primary rock mass by hydraulic fracturing (HF). The major perceived benefits of this process are a decrease in the magnitude of the expected maximum seismic event and improved cave propagation. In addition, HF has resulted in new information on the propagation pressures of each fracture. Previous studies have attempted to relate propagation pressure to minor principal stress or confining stress.Considering the spatial continuity of propagation pressure and the significant quantity of collected data since the incorporation of the HF technique, minimum requirements for geostatistical modelling have been reached, permitting robust estimates inside the representative volume with acceptable errors (Cornejo, Muñoz and Rojas, 2012; Cornejo and Landeros, 2013). These results are then used to identify zones with higher magnitudes, which are mostly related to more complex geotechnical zones (intrusive and major faults) and caving singularities, making it possible to estimate the spatial extension of these zones.Finally, these results are integrated with other geomechanics aspects to support risk analysis of the mining plan.CITATION:Cornejo, J, Landeros, P, Benado, D, Caviedes, C and Pinochet, A, 2016. Geostatistical modelling of hydraulic fracturing pressures at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Sergeant G. D, Norman J. R

The importance of reducing the moisture content of fine coal, the nature of the retained water and the means of its removal are discussed. A statistical technique, using a balanced block design, was used to isolate the significant factors determining water content of a coal filter cake, The most significant factor was particle size distribution. A simplex evolutionary operation (evop) was used to determine the optimal quantities of additives required to produce the lowest moisture content for a selected coal size. For this optimum condition (18.6 lb xÇ20 per 100 lb dry coal), additions of 0.045 lb magnesium ion, 0.0026 lb separan A.P. 30, and 0.098 lb aerosol O.T., per 100 lb dry coal were required. The work illustrated the uses of statistical evop technique for the determination of optimal conditions in industrial research projects.

Jan 1, 1969

By E Hollinger, J L. Mauk

Gold-silver mineralised veins at Favona, represent a new low-sulfidation epithermal vein discovery that occurs less than 1 km southeast of the world-class Waihi deposit. The Favona vein is hosted in Late Miocene andesitic lava flows and local dacitic tuffs that are intensely altered to quartz, adularia, chlorite, illite or interstratified illite-smectite (with ten to 70 per cent smectite) and pyrite. Adularia is widespread and envelops the veins, whereas chlorite and illite are mostly restricted to the footwall, and illite-smectite is confined to the hanging wall of the Favona vein. At shallow levels, kaolinite, cristobalite and rare alunite overprint the above minerals. A polymict hydrothermal breccia also occurs above and in the hanging wall of the Favona vein and contains clasts of altered andesite and various quartz vein fragments. Fluid inclusions in quartz veins sampled over a 300 m vertical interval have a homogenisation temperature range of 175¦ to 266¦C and dilute apparent salinities of 220¦C and grading into illite-smectite and local smectite which formed at 2. In contrast, late kaolinite, cristobalite and alunite formed from descending steam-heated acid-sulfate waters. Overall, the Favona and Waihi deposits are interpreted to have formed at similar levels in a single low relief hydrothermal system, with each deposit representing a distinct zone of fluid upflow.

Jan 1, 2002

Smarter Gravity Separation Using the Kelsey Centrifugal Jig With relatively coarse grained and easy-to-process ore sources rapidly dwindling, smarter techniques are becoming more necessary for the continued success of mineral processing operations, while increasing environmental pressures also require more environmentally friendly solutions. Gravity concentration has long been employed to pre-concentrate minerals using water, reducing or eliminating the need for less environmentally friendly processing techniques such as flotation. Conventional gravity recovery devices however, operate in a 1 g environment with limited efficiency in the separation of fine particles of heavy and gangue minerals. More recently developed centrifugal concentrators operate in a multi-g environment and enable finer heavy minerals to be recovered, but also exhibit limited separation efficiency due to the separations being based on solid particle mass differentials. Further enhancement of gravity separation has been achieved using the Kelsey Centrifugal Jig (KCJ), which also operates in a multi-g environment, but separates minerals on the basis of specific gravity differentials, using 'ragging' media and a pulsation mechanism, which maximises the effect of differential particle accelerations. This enables the efficient separation/recovery of minerals down to a particle size of ~6 ¦m and/or separation of minerals with a low specific gravity differential. This paper presents details on the principals of operation of the KCJ, recent improvements in the technology and recent developments in modular KCJ plants, as well as some KCJ application areas, which offer smarter, environmentally friendly processing opportunities for the mineral processing industry.

Sep 13, 2010

By Met M, Orr C. W, Met B. E

As was mentioned in the last paper of this series(l), magnesium was added to lead with the idea that it would act as a de-oxidiser. The magnesium lead alloys give rise to an inter-metallic compound of the composition Mg2Pb(2) and it has some remarkable properties. It is known to disintegrate on standing in the atmosphere and it confers this property also on lead alloys in which it occurs. Magnesium forms a solid'solution with lead, and according to Kurnakow, Pogodin' and Vidusova(S) the limits of solubility are as follow...In conformity with the practice used in preceding series, the limit of concentration used in the present investigation was 0.1 %. Accordingly, it would be expected that all the alloys used would consist of the solid solution and the detrimental Mg2Pb would be absent. Whilst this was the case, it...

Jan 1, 1939

That gold will dissolve in sodium hyposlphite solutions is known from the lixiviation of silver and gold ores.The gold will dissolve only in small quantities. According to Stetefeldt, if gold leaf is treated for a time with sodium hyposlllphite solutions of varying strengths solution takes place in every instance, the deviation in quantity being very slight.In order to form hyposulphite double-salts, the gold must become oxidised, the oxygen being derived from the air absorbed by the solution. Consequently, it is the quantity of free oxygen in the solution by, which the reaction is determined, as for one equivalent of gold dissolved one equivalent of caustic soda is set free.

Jan 1, 1901

The perennial challenge facing mining and minerals operators is to improve productivity, usually by a combination of cost reduction and performance improvement. In a typical production situation involving mining and processing activities, the standard approach has long been to seek improvements in each activity, effectively in isolation from each other. However, the realisation is growing that there is considerable potential to achieve really substantial productivity gains by much improved integration of mining and processing with the key being to consider what is best in the total sense. Some of the linkages between fragmentation in mining and downstream processing are considered in this paper. These linkages involve technical, operational and economic Considerations.

Jan 1, 1997

By D Brett

"Mine waste storages including tailings dams and waste rock dumps represent arguably the biggest risk on a mine site from both physical and geochemical viewpoints, related firstly to structural stability and the consequences of failure and secondly from potential on-going seepage or run-off of acid and metalliferous drainage (AMD). The risks are most likely to increase during operations and continue through the closure and post-closure phases, with the waste storages likely to be the most difficult features to resolve in the mine closure process. Contaminated water quality from tailings dams and waste rock dumps can require treatment "in perpetuity" at a cost of hundreds of millions of dollars. The problem is increasing with ever larger mine operations and waste generation volumes. This paper identifies leading practice methodologies in planning and operating mines and process plants to minimise the risks from tailings storages and how this might also affect waste rock management and even the design of mine excavations. These methodologies require a "big-picture" approach to develop an understanding of the overall issues and identify synergies between the different operational areas on a mine site that can reduce overall risk. With a conservative approach and realistic allowance for future costs it is possible to facilitate decisions at the mine planning stage that can reduce risk and save cost over the long term. This is in contrast to the common approach where each operational area is looking to minimise its own costs with a short-term view. Incorrect mine methodologies can be developed by allowing net present value (NPV) accounting methods to trivialise future closure issues.Methodologies discussed include: Integrated Waste Management - Significant structural improvements to tailings dams can be achieved if the structures can be incorporated into the waste rock dumps. Risk of AMD can also be reduced by utilising the tailings and waste rock effectively. This could go even further to consider the placement of wastes to limit mine void environmental issues; Process Optimisation - Water quality and the nature of potential tailings dam structures can be highly influenced by the geo-chemistry of the tailings. This can be modified by processing, where simple changes such as maintaining separate streams of geo-chemically different tailings rather than recombining them or by initiating further processing to remove problematic minerals such as sulphides; Enhancing Geophysical Properties - The geochemical performance of waste repositories can be greatly influenced by the geophysical properties of the stored materials, particularly the air-water characteristics, which are influenced by particle size, density and permeability. The geotechnical properties can be enhanced by strategic paddock dumping, blending and compaction.These methodologies are demonstrated by case histories.CITATION:Brett, D, 2013. Mine waste risk minimisation by integrated waste management and process optimisation, in Proceedings MetPlant 2013, pp 247-258 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

The Department of Mineral Resources is the lead agency in mine site environment management and control in New South Wales. The Department introduced a Mining, Rehabilitation and Environmental Management Plan (MREMP) process several years ago in order to integrate the activities of other government agencies who may have a material interest at the mine site. The MREMP process has resulted in a spirit of trust and co-operation between agencies and between agencies and mining companies. The spirit of co-operation has been reflected in greater public confidence that mining is environmentally responsible.

Jan 1, 1995

A general outline of the significant features in the quality and manufacture of the more common refractories is given. Where possible, linkage between quality development and control and service applicationhas been shown and explained. INTRODUCTIONThe refractory industry is no stranger to change. New processes and revision of old processes in other industries are the harbinger of new and revised products in refractories.Few of the changes are dramatic; generally they are evolutionary rather than revolutionary. New developments are additional to, and inclusive of, established practice.Therefore in this paper it is necessary to repeat much of what is already known in order to show the development taking place.FIRECLAY REFRACTORIESGeneral technology Fireclay refractories are the most common, the most varied and the most versatile of all refractories. Virtually any composition of silica and alumina up to the composition of kaolin is possible. For purposes of comparison they may be classified in the Continental fashion in accordance with chemical composition or in the American way according to "duty". That the two methods are equivalent is shown by an inspection of the alumina-silica diagram of Bbwen and Greig (1924). 'Fireclay refractories are composed of a glassy and a crystalline component derived from the chemical and physical nature of the raw materials used in their manufacture.

Jan 1, 1961

By M Zhu, G Tranell, J You, K Tang, X Ma

The thermal conductivity of slag is critical for the efficiency of high temperature metallurgical processes such as the smelting reduction of ferroalloys, the ladle refining and the continuous casting mold flux in steelmaking. Experimental determination of slag’s thermal conductivity is fraught with challenges, as seen in yielding data for the SiO2-Al2O3-CaO system that are often inconsistent and widely dispersed. In molten slags of this system, thermal transport occurs via phonons within the network structure. To quantitatively describe thermal conductivity based on the microstructure, hightemperature Raman spectroscopy was employed to measure the silicate tetrahedra Qi (i = 0, 1, 2, 3), with Q4 species inferred from mass balance. This study also integrated molecular dynamics simulations to provide a fundamental understanding of the microstructure units distributions. Machine learning algorithms, especially deep neural networks, were applied to establish the relationship between slag composition and the configuration of tetrahedra. The thermal conductivities were then connected with silicate tetrahedra Qi using an Arrhenius-type formalism. This study sets the stage for extending our findings to more complex, multicomponent slags, enhancing their practical application in industrial processes.

Aug 21, 2024

By N K. DavT, A Coggan

The performance of in situ, shallow water covers in controlling acid generation was evaluated at four recently decommissioned pyritic uranium tailings sites at Elliot Lake, Ontario, Canada. The tailings are acid generating, having a pyrite content of approximately five to ten per cent and a very low to non-existent alkaline buffering capacity. Adverse market conditions led to the closure of all operating uranium mines in the early- to mid-1990s, followed by rehabilitation and decommissioning of mine and waste management facilities. In order to control acidic drainage, all new and active tailings areas at Denison, Quirke, Panel, Spanish-American and Stanleigh mine sites were re-engineered to provide in situ submersion of these tailings under shallow water covers. The tailings impoundment dams were upgraded and reinforced or in some cases reconstructed, to minimise seepages and provide a minimum 1 m depth of water cover. With the exception of Stanleigh mine, which was closed in 1996 and rehabilitated during the late-1990s, the water covered Tailings Management Areas (TMAs) at other sites have been in operation for a period of six to nine years. The surface water quality at these sites is maintained at near neutral pH conditions by periodic addition of lime slurry to the established water covers. Additional treatment of effluent is provided as required to meet the discharge water quality standards. The performance of the established water covers at the sites was evaluated by analysing the annual equivalent limestone consumption data. The results were compared with the performance of an older, decommissioned Nordic TMA, which was rehabilitated using revegetation techniques. The water covers at these sites are performing as designed and acid generation has been reduced to low levels. Based on the total amount of yearly equivalent limestone required to maintain water quality in the water cover and at the effluent treatment plant, it is concluded that acid generation rate at the Denison TMA has reduced to less than 0.15 per cent of its pre-water cover conditions during normal operation and rehabilitation periods. In comparison to the revegetated Nordic TMA, the acid generation rates at Denison and Panel TMAs have decreased to less than 1.6 per cent of that at the Nordic TMA. The acid generation rate at the Quirke TMA was comparable or only slightly lower than that at the Nordic TMA because of its unique terraced cell configuration, having tailings in five hydraulically interconnected cells at different elevations. Historic acidity and oxidation reaction products, accumulated during normal operating and pre-water cover periods, are flushing from upstream locations to downstream cells, thus requiring much higher equivalent limestone additions for acid neutralisation and effluent treatment.

Jan 1, 2003