Search Documents

One of the responsibilities of the Melbourne and Metropolitan Board of Works is to provide a sewerage system for the metropolis of Melbourne which now contains over 2.5 million people. In providing this sewerage system it was necessary for the Board to embark on a large tunnelling programme some 20 years ago. As a result of this extensive tunnel construction programme, tunnel boring machines and shaft sinking methods have been developed to cope with the soft ground and soft to medium rock found in the southern and eastern areas of Melbourne where the majority of the recent tunnelling has been carried out. While in the last few years radical changes in construction methods have not been made, development has continued and improvements have been made, which have enabled the Board to extend the limits of the ground conditions in which it can efficiently construct shafts and also tunnels with boring Machines.

Jan 1, 1976

By Mathews K. E, Willstead T. V C

Initial glory holing was followed by sublevel stoping, with a small proportion of total production mined by shrink and cut-and-fill methods.The sublevel stoping method was successfully modified to cater for altering ground conditions encountered at increasing depths. At present, 94 per cent of production comes from sublevel stopes. The evolution of this mining method and current techniques and practices is outlined. A combined shrink and,sublevel benching method was also developed to increase the mining rate of narrow orebodies over the standard stoping lift of 380 ft. Pillar recovery and stope filling operations have been continuously modified to suit the relIuirements of a rapidly developing mine.INTRODUCTIONOre production commenced at Mount Isa Mines in June 1931. Since then production has increased from approximately 2,500 tons of lead ores per mine day to the current 11,000 tons of sulphide ores per mine day comprising 3,100 tons of lead ore and 7,900 tons of copper ore. The early planners selected sublevel stoping with ring drilling for ore breaking as the most efficient and economical for Mount Isa conditions: This method satisfied requirements for:1. a low cost mining method for the comparatively low grade ores,2. a stoping sequence allowing development, stope preparation, breaking and drawing of ore to proceed concurrently,3. a method of extraction in which broken ore in the stopes would be kept to a minimum because of adverse effects of oxidation on mill metallurgy and...

Jan 1, 1961

By McLeod RL

The Tolukuma gold-silver prospect is located approximately 100km N of Port Moresby in the Central Province of Papua New Guinea (PNG). Epithermal "adularia-sericite" style mineralisation crops out over 1200m within an en echelon quartz veined zone 1 to lOm wide. At a 4g/t cut-off grade, a geological resource of approximately 1.47Mt @ 13.77g/t Au is indicated from 38 diamond drill holes completed since discovery by Newmont Pty Ltd in September 1986. At a regional scale, Tolukuma miner- alisation appears localised in a dilatant zone at the intersection of a 1150 magnetic structure, and the western margin of a N-S trending graben which is filled by a Pliocene volcanic complex contemporaneous with the Mt Davidson Volcanics 30km to the W. A l0km diameter circular Landsat feature, which may reflect magma emplacement at depth, occurs immediately N of Tolukuma and nearby mineralisation. Mineralisation at Tolukuma occurs in sub-vertical quartz veins at, or adjacent to the faulted contact between Pliocene basic and intermediate volcanics/intrusives, and quartz mica schists and phyllites of the Cretaceous Kagi Metamorphics. Most veins display evidence of multiple episodes of brecciation and textures indicative of cyclic boiling, including crustiform rhythmic banding and quartz pseudomorphs after platy calcite.

Jan 1, 1991

By J Player, R de Vries, E Villaescusa, R Hassell

Concerns regarding the uncertainty of stope dilution at MMG Dugald River Underground Mine led to a trial stoping program to acquire full-scale comprehensive geotechnical information and to test the validity of the geotechnical and mining parameters. Given that stope production drilling and blasting is a key parameter that influences dilution a detailed stope blast vibration project was implemented. The stoping trial consisted of 19 stopes, a combination of both sublevel open stoping and longitudinal and transverse stopes, of which five were monitored for blast vibrations.The blast vibration project utilised 20 triaxial geophones and five triaxial accelerometers installed in the hanging wall of five monitored stopes. For each stope fired, full blast waveforms were recorded along with detailed information of the blast design. Analysis of the blast vibrations used the Holmberg-Persson approach, with potential damage determined by the relative (Holmberg-Persson) K values.The project identified the benefit of parallel, breakthrough slot holes in reducing blast vibration damage. The results show that radial rings toeing or stabbing into the stope wall lead to higher vibrational energy yield which contributed to increased overbreak. Hanging wall overbreak, by comparison, with parallel, breakthrough blastholes with 1 m standoff, combined with lower density explosive charging (0.8 EP) and increased delays limited blast vibration damage. A number of ring burdens from 1.4 m to 2.5 m were monitored with no difference in terms of energy yield being identified. Changes to the stope drill and blast design are suggested to better control the large blast vibrations and recommendations from this project have been implemented into future mine design and planning.CITATION:Hassell, R, Villaescusa, E, de Vries, R and Player, J, 2015. Stope blast vibration analysis at Dugald River Underground Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 221–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The works of Metal Manufactures Ltd are situated at Port Kemblam NSW, within a few hundred yards of a deep-water harbour. At present they occupy about 26 acres, and ample provision has been made for future extensions. Rail connection exists between various parts of the Works and the main South Coast Railway, the harbour jetties and the adjacent copper refinery of The Electrolytic Refining and Smelting Co Ltd. A plan of the works is shown in Fig 1.The company was incorporated in March 1916, and commenced production of copper wire in June 1918. Early in 1920, tube manufacture was undertaken, followed by telephone cable mnufacture in 1923. Today the Works consist of five principal sections: Founrdy, Tube Factory, Wire Factory, Cable Factory and Case and Drum Factory. Whilst the last four are engaged in producing the finished materials for despatch from the Works, the first-mentioned is engaged in producing copper, brass, and other non-ferrous billets for use in the Tube and Wire factories. In addition, there are Engineering and Metallurgical Departments supporting the manufacturing sections, and in these, as well as in all other sections of the Works, extensions have been carried out from time to time to provide for increased output and new types of products.

Jan 1, 1938

By E S. Bernard

Toughness testing of fibre reinforced concrete (FRC) at 28 days age is typically undertaken as part of quality control for the many applications where fibres are used in concrete, including shotcrete, tunnel segments, and cast-in-place tunnel linings. The performance achieved at 28 days is usually assumed to be retained with increasing age. However, as the average strength grade of concrete used in most tunnelling applications, including tunnel segments, has steadily increased over the last 20 years, this assumption is becoming increasingly unviable. This is because for some types of fibre the mode of post-crack fibre behaviour depends on the strength of the concrete and can change from a desirable high-energy pull-out mode to a low-energy rupture mode as the strength and age of concrete increases. This paper describes a series of trials performed over two years in which the American Society for Testing and Materials (ASTM) C1609/C1609M beam tests were used to assess the performance of FRC reinforced with two widely used brands of steel and macro-synthetic fibre. The hooked-end steel fibres used for half the beams exhibited a dramatic fall in performance beyond 56 days age as the mode of failure changed from pull-out to rupture. The other fibre did not exhibit a fall in performance with age. This phenomenon highlights the need to quantify performance of FRC at much later ages when long-term performance is required, for example, to resist seismic events or changes in ground stress due to nearby excavations. As an alternative, a reduction factor may be applied to the performance of FRC mixes for which evidence of satisfactory long-term performance is not?available.CITATION:Bernard, E S, 2014. Age-dependent changes in post-cracking performance of fibre-reinforced concrete for tunnel?segments, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 229–236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Floyd JM

Conventional smelting reactor systems were designed to recover only one main element from their feedstocks. They did not possess sufficient flexibility to allow optimisation of co-production of multiple values from a complex feed.New reactors such as Sirosmelt and Top Blown Rotary Converters are providing new possibilities for making separation between components and this is of great significance for the complex feeds which are becoming prevalent in the metal extraction industry.Process routes using chemical procedures which take advantage of the flexibility of these reactors will be discussed in relation to a number of possible feedstocks.

Jan 1, 1985

By Y Yamaguchi, S Nomura, M Matsumura, C Kamijo

In order to increase productivity and decrease reducing agent rate (RAR) of blast furnaces, slag content of sinter ore must be decreased. However, gangue content in iron ore tends to increase because of resource depletion. Therefore, amount of high-grade concentrate in sinter ore feeds should be increased, but this situation causes a decrease in permeability of the sintering bed so that the productivity of sinter process decreases. In order to increase the amount of concentrate, NSSMS has developed the P-type separate granulation method, RF-MEBIOS and SPEx II technologies. These technologies have been introduced to actual sintering machines. In this report, a new technology using microparticles of iron ore is proposed to increase the amount of concentrate in sinter blends. Basic experiments simulating the sinter making process using microparticles of iron ore were undertaken. Crushed pisolite, containing >60 wt per cent -10 µm was prepared for binder. The pisolite microparticle binder was mixed with another Australian sinter feed ore in a high-speed agitating mixer. They were mixed for about one minute, and then granulated using a pan pelletiser. After that, they were added to another raw material mixed by a drum mixer, and then charged in a pot for a sinter pot test. As a result, when the amount of concentrate increased from 13 wt per cent to 20 wt per cent, productivity was almost kept constant using pisolite microparticle binder.CITATION:Kamijo, C, Yamaguchi, Y, Matsumura, M, Kawaguchi, T and Nomura, S, 2017. Development of an iron ore microparticle binder for increasing the concentrate content of sinter blends, in Proceedings Iron Ore 2017, pp 69–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Pipe Flow Stability of Concentrated Coal-Water Suspensions in the Presence of an Electric Field

Sep 13, 2010

By D W. Nisbet

Today Hudson Bay Mining and SmeltingÆs 777 Project is the largest mining construction project under way in Canada. The project comprises six components: construction of the new 777 zinc-copper mine; construction of the new Chisel North zinc mine that will truck ore out from 600 metres below surface; expansion of the Flin Flon ore concentrator; expansion of the zinc plant to increase throughput by 15 per cent; a spill gas project that will reduce fugitive gas emissions by some 90 per cent; and infrastructure improvements including construction of a new electrical substation. Total investment in The 777 Project is over $US 260 million. Seven years ago, the Flin Flon, Manitoba-based company was fighting for its very existence. How does a company go from down-for-the-count to robust contender in just seven years? Contributing reasons are many, but all have their root in a process HBMS calls æTransformationÆ. It is transformation that has taken HBMS, a very traditional company, through a very non-traditional turnaround (Figure 1).

Jan 1, 2000

By W Ilahi

Underground metalliferous mining methods often result in the formation of vertical openings to facilitate the extraction of orebodies. These development and production techniques can result in the creation of vertical open voids, which include stopes, orepasses, ventilation raises and other excavations. There are risks associated with the use of mobile plant in the vicinity of these voids, especially during backfilling and when bunds are constructed at the edge of a stope or void. These voids can present unacceptable risks if not adequately managed.

May 5, 2022

Barrick Gold Granny Smith Mine is currently undergoing conversion from an open cut operation to an underground mine at the Wallaby deposit. The underground project commenced in 2005 with the development of the reserves immediately below the pit and is now currently entering a production ramp-up phase for mining of these two initial surfaces below the pit. With increasing gold prices the owner has been forced to re-evaluate the underground project and has decided to investigate the potential of a deep level mine. This deep level underground mine presents a collection of challenges with the most notable being exploitation of a series of well separated near horizontal lodes ranging in thickness from less than 1 to 20 m. A variety of room and pillar mining methods are employed for extraction with careful consideration to resource recovery and pillar design for long-term stability. Compounding these deep level challenges is a need to accelerate mine level development to maintain the production profile of the mine. This paper describes the challenges, key learnings and outcomes of the studies undertaken to date associated with this project.

Jan 1, 2008

By S A. Ravishankar

In heavy minerals separation, the titanium and iron oxide phases are separated from silicates in the coarser particle size range (80 - 150 mm) using magnetic and electrostatic separators. With the ongoing challenge of heavy mineral ore deposits getting increasingly finer in particle size, conventional separation equipment suffers from the ability to process this material at the same throughput rate as coarser particles. A variety of magnetic separation technologies were developed to perform at a much finer particle size range, down to 2 mm in the clay industries mainly to remove titaniferrous oxide particles. Complementing the developments made on the physical aspects of magnetic separation, Cytec Industries has recently developed a ‘bolt-on’ chemical enhancement technology for magnetic separation (CEMS). This is to enable separation of finer particles, and weakly paramagnetic titanium phases from diamagnetic silicates that are not amenable to magnetic separation. This paper will provide an outline of the technology, illustrate its ability to process a wide variety of ores, and also discuss plant limitations. The major advantages of chemical enhancement technology to magnetic separation includes: simple dosing equipment extension to existing magnetic separation technology; ability to produce product of comparable quality with improved cost effectiveness, when compared to incumbent flotation; removal of impurity minerals over wider size range; enhanced removal of non-magnetic impurities; and improving the process robustness. Furthermore, chemical enhancement technology for magnetic separation has also emerged as a platform for removing impurities at lower levels in other mineral systems as well.

Oct 5, 2011

A new lead refinery with a capacity of 230,000 tons per year commenced operation at Port Pirie in October, 1959. This plant superseded the refinery which had operated from 1933 with the advent of the continuous lead refining process. The incorporation of new equipment following local metallurgical developments, together with the overseas demand for lead of extremely low antimony content createddifficulties in operating the original plant. The new refinery project was undertaken to cover this disability and to gain the full advantage of the new processes.Desilverising and softening are carried out in units identical in size to those used previously. Metallic zinc is recovered from the entire output of desilverised bullion by vacuum distillation. Final refining is carried out by batch treatment with caustic soda yielding lead of purity previously unattainable at Port Pirie.These two processes replace continuous dezincing by oxidation, a high temperature process which caused large quantities of lead and antimony to be recirculated. The final stage is a batch process; therefore the product composition can be checked before casting. Individual batches can be adjusted to produce special alloys to consumer's specification.Improved casting equipment allows the quantity production of pigs of good physical characteristics either as 56 lb bars or 2000 lb pigs.This, together with the high purity of the lead, assures the Broken Hill Associated Smelters Pty. Ltd. (RH.A.S.) position in world markets.Automatic control systems are extensively employed, particularly on the vacuum dezincing unit.The anticipated financial benefits have been achieved mainly by a reduction in the tonnage of recirculated materials, a smaller labour force, and reduced maintenance requirements.INTRODUCTIONIn December 1956 a decision was made to build at Port Pirie a lead refinery on a completely new site, and in October 1959 the new refinery was brought into operation. This plant superseded the lead section of the old refinery which...

Jan 1, 1963

The modern Golden Cross mine entered the production phase in January 1992. The project is designed to produce over 100 000 oz/yr of gold and over 300 000 oz/yr of silver during a mine life of eight years. An open pit and an underground mine are operated producing around 850 000 t/yr of ore, to feed a conventional carbon-in-leach processing plant. Golden Cross is owned in joint venture by Coeur Gold New Zealand Limited (80%) and Viking Mining Company Limited (20 %).   Since the start of production several major aspects of the design have altered. The underground mine began as a mechanised cut and fill operation. The cut and fill stoping progresses in 3.3 m flatback lifts with maximum stoping width of 6 m. Where the ore zone is wider than 6 m a post pillar cut and fill method is used. In 1993 a new bench mining plan was introduced between the 270 and 260 levels. Flatbacking continued in the footwall drives in anticipation of variability of the ore width and orientation. The development of levels below the main service 200 level has indicated a possibility of bulk mining the ore block rather than flatbacks. This could lower mining costs but also introduce higher dilution rates. Development is in the advanced stages for trialing this method.

Jan 1, 1994

By Moorrees C

Tests show how that temperature and rate of sparging to remove carbon dioxide determine the rate of precipitation and the chemical and physical properties of hydrated magnesium carbonates precipitated from clarified magnesium bicarbonate liquors derived from crude magnesia. At temperatures above 55°C the product is largely in the form ofhydromagnesite, Mg5(C03)4(OH)2.4H2O Between I5°C and 55°C the major product is nesquehonite, MgCO3·3H2O, although partial hydromagnesite precipitation can be induced by a high rate of aeration.As a result of the reduced time required to bring about greater than 95 per cent magnesium precipitation, the higher MgO content of the product, the ease of product recovery from the precipitation vessel, and the lower energy requirement for thermal decomposition of the precipitate to magnesia, it is preferable to precipitate hydromagnesite rather than nesquehonite. Moreover, the magnesia produced from hydromagnesite is somewhat more reactive than that formed from nesquehonite.Using precipitate calcination temperatures less than 1000°C, the chemical reactivities of the magnesias formed from both precipitates are greater than those of the crude magnesias derived from Savage River magnesite itself. The magnesias would be suitable for most uses developed for caustic-calcined magnesia. However, for refractory brick manufacture, it would be necessary to briquelle the caustic-calcined magnesia. adjust the CaO and SiO2 contents and sinter at temperatures in excess of 1600°C. This would bring about an increase in the bulk density and induce the appropriate chemical bonding reactions.Dead-burned magnesia produced from Savage River magnesite by the calcination/carbon dioxide route would have very low B2O3 contents, typically less than 0.0001 per cent.

Jan 1, 1985

The distribution or the userul minerals or Tasmania is so closely connected with the geological structure of the island that it will be convenient to briefly recapitulate the principal ract or its geological history, before describing the ore and other deposits. In many cases these present features which are very puzzling in the absence of knowledge of the structure of the districts in which they are found and in all cases it is of benefit to mining engineers to be acquainted with the main facts of the geological·history of the regions in which they have to carry on operations. Moreover, in speculating as to the origin of lodes and other deposits, we have constantly to rerer to the crumplings or the earth's crust by mountain-making movements, and to the igneous rocks which have been thrust throngh the other strata, to explain the origin or the lode fissures, and this discussion cannot be carried on without knowledge of local geology.The oldest rock yet met with in Tasmania are of Archooan age, and consist of highly crystalline quartzites and micaceous schist. They are most extensively developed towards the western side ot the island, forming a belt parallel to the West Coast from South-West Cape to Cradle fountain; but they also crop out here and there to the west and northward of this belt, where the covering strata or later age have been denuded away. Though not seen in situ in the eastern part of the colony, the abundance or pebbles derived from this formation in the conglomerates of the coal measures shows that it must in those day have formed land surfaces there also, and makes it likely that the archooan strata exist at no great depth: below many of the beds of later age now occupying the surface. Lying unconfortably upon these highly metamorphic strata we find next an extensive series of subcrystalline metamorphic conglomerates, grits, sandstones, slates, and limestones,of Cambro-Silurian age. These are well seen in the Gordou River Basin, along the West Coast Range, aloug the North Coast, and in the goldfields of the north-eastern portion of the colony. They are much broken by later intrusive rocks, and covered by younger rormations, but the series is spread more or less over the whole island.

THE following brief paper is submitted with a view to encouraging the exploitation of hitherto neglected 10w~ grade ore-bodies which are suitable for extraction by open-cut methods.The Corinthian North mine, situated 10 miles from Southern Cross, in the Yilgarn district of Western Australia, furnishes an example of low working costs, although operations are carried out on quite a limited scale.The body of quartz which is now being worked strikes N.W. and S.E., has a very slight underlie to the west, and lies between bodies of quartz-hrematite s,chist on the east and amphibolite on the west.So far as the property has been explored, it would appear that the underlying sulphide rises to within about 70 ft. of the surface in the northern end of the workings, and pitches away to the south at a grade...

Jan 1, 1915

Reliable predictions of the long-term water quality and water level fluctuations in a final void are vital if mine operators propose to decommission final voids in open cut mining operations. The catchments feeding final voids typically comprise a large proportion of coal placed or re-shaped spoil piles. Spoil piles from open cut coal mining operations have distinctive hydrological characteristics, which result in unique run-off behaviour. There is a need to understand the nature of spoil hydrology processes in order to predict the long-term hydrological behaviour and water quality responses of such systems. Preliminary estimates indicate that it may take 20 or more years for a void to flood. It is impractical for mine owners and operators to wait until long-term hydrological and water quality conditions have been established in a void, before reaching agreement with regulators about mine closure conditions. Reliable simulation of the long-term water quality and water level fluctuations in a void are therefore. The adoption of an agreed modelling approach and sharing of results from field data programs could result in the establishment of a database that could be used, with regulatory approval, for assigning parameter values, without the need for a specific data collection program for every individual void. Industry and regulators should agree on the model adopted for predicting post-closure behaviour of spoil/void systems. This will require reliable, robust methods for field data collection. This paper describes the field monitoring, data collection, model preparation and simulations undertaken over a three year period for Australian Coal Association Research Projects (ACARP) Project C7007. It presents the findings of that research, and provides comment on aspects of the project that were undertaken well and on aspects that could have been done better. Limited data is presented in this paper due to confidentiality arrangements with the relevant mine sites.

Jan 1, 2003

By Chaves AP, Delboni H. Jr

Thermal comminution is an industrial process specially suited to very abrasive material, when contamination with Fe from wearing parts of conventional crushing and grinding equipment must be avoided. It involves an initial step of heating the material to be comminuted, followed by sudden cooling (quenching) and finally by a conventional mechanical process to disassemble the particle aggregates. The thermal step is, in fact, a pre-fracturing process. The heating operation causes changes in phase of the minerals and changes in volume of these minerals and other substances included in pores and cracks. The cooling operation causes thermal shock reversions or the phase transformation and consequent generation of internal stresses, high enough to fracture the solid.

Jan 1, 1993