Search Documents

By R Benton

Since commencement of underground production in March 2006 the Kencana K1 orebody has delivered over 0.9 Mt of ore containing 1.18 Moz Au until April 2009. The Kencana deposits are part of the Gosowong goldfield located on the island of Halmahera in eastern Indonesia. The district has produced over 2.3 Moz since mining commenced in 1999 with the first two deposits extracted by open pit methods. The K1 deposit is technically challenging being a vein style deposit with poor to very poor ground conditions and a relatively low overall dip of around 45 degrees to mine grid east. It is mined under geological control by underhand cut and fill methods utilising cemented paste backfill aiming for 100 per cent extraction. With these conditions the operation was mine limited in the initial two years of production resulting in low stockpile levels for mill feed blending and hand-to-mouth mine to mill production. Mill feed rates have increased from 30 t/h to 55 t/h over this period following business improvement projects while mine production has escalated to match this increase as deeper levels of the deposit are accessed. The operation has now become mill limited. Monthly mill gold production from Kencana has ranged up to 50 000 oz with head grades ranging between 8 g/t and 122 g/t Au on a daily basis. As individual grade control assays can extend into the per cent Au range there are challenges in sampling, modelling, mining, blending and milling the Kencana orebody. At the time of commencement of ore driving in K1 the national geology team had little prior experience in underground mining and systems were in early development. The variances in feed grade and tonnages have been reduced with time as the operation evolves and business improvement initiatives are undertaken to smooth peaks and troughs in ore supply. Two such initiatives in the geology department have added over US$20 M of additional revenue per annum.

Jan 1, 2009

By R A. Bearman

Recent demand pressures for iron ore should not distract from the longer term view that intense competition in the industry has demanded technological innovation of a high order. There is a long track record of successful innovation underpinned by a solid base of scientific research and knowledge. By comment on recent developments in trucks, comminution and direct smelting, this paper suggests that innovation is still a key attribute of the industry. The spending of the minerals industry on underlying science, however, is not particularly high. By looking at other industries we can ascertain that for step change technologies, it is particularly advantageous to have a solid base of science and technology underpinning developments.

Jan 1, 2005

By Y Wei, P Soole

This paper gives a brief description of VirtuoBlast technology ù a new, automated and highly interactive stereo vision technology which has been developed in CSIRO Exploration and Mining. VirtuoBlast technology is an integration of three advanced technologies - close-range digital terrestrial photogrammetry, oblique stereo imaging or high-speed stereo imaging, and temporal-spatial image matching technique. VirtuoBlast has been developed for the automated 3D measurement of blasting through rapid collection, processing, analysis and visualisation of 3D data related to blasting. A major field trial has been undertaken in August 1998 at the KCGM super pit. The field trial involved three applications of the technology, namely, pre-blast 3D surface mapping; post-blast 3D performance measurement; and temporal-spatial modelling of dynamic blasting process. This paper presents some results from this trial with emphasis on the application of VirtuoBlast technology to pre-blast 3D surface mapping and post-blast 3D performance measurement. Application to the temporal-spatial 3D modelling of dynamic blasting process will be presented in a separate paper. Pre- and post-blast surface models derived using both VirtuoBlast technology and conventional field survey method are presented. The differences in results using the two mapping methods clearly show that the digital photogrammetric technique has many advantages over conventional survey methods. Results of pre- and post-blast from the field trial have demonstrated the potential of VirtuoBlast technology to efficiently perform pre-blast 3D surface mapping and post-blast 3D performance measurement of production blasts. Demonstrated applications of VirtuoBlast technology to automated 3D measurement of blasting are showing an exciting future in advancing blasting science and modern blast design. The basic technologies are in place, however, continued improvements to the functionality, robustness and outputs are needed. The challenge is to build on the current state-of-the-art, by developing techniques and hardware which can be easily transferred to and implemented by the mining community. Current and future research and development will see improvements in imaging systems, automatic image processing and 3D data analysis.

Jan 1, 1999

By G J. I dos Santos

The risk assessment of mining projects is directly related to the possible failure in estimating, and as estimates are made from sampling results, this activity should be done in a judicious and planned manner, to avoid surprises at the start of project operation. Pierre Gy’s (1995) sampling theory addresses the issue of sample representativeness and indicates that only the certainty that the sampling procedure was performed with quality may result in samples being recognised as representative. To validate the representativeness of samples from sampling boreholes selected for studies of mineral processing, the team of geology resource assessment of VALE has proposed a methodology based on the use of statistical analysis tools, which in addition to considering the spatial distribution of these samples in deposit, considers whether they are representative of the populations studied, allowing the geologist to make a quick analysis of sample representativeness.

Jul 11, 2011

By Fuller P. G, Dugan K. J

Artificial support can be used to improve wall stability in open pit mines. This is examined for a particular case where the factor of safety for a slope is kept constant by using artificial support as the slope angle is increased. It is demonstrated that the savings in excavation generally exceed the cost of support. However, in order to correctly judge the eco- nomic impact of artificial support on the project, all the elements relat- ing to the use of artificial support must be taken in account.

Jan 1, 1989

By Dharmappa HB, Sivakumar M

This paper is concerned with two case histories of wastewater quality management in underground coal mines in the Illawarra region. The first investigation briefly presents an analysis of mine water discharge having an extremely high concentration of suspended solids and consistently high barium concentrations, averaging, 14.4 mg/I Barium, over the sampling period. A laboratory study of chemical precipitation processes has indicated that about 91% of barium could be removed by using ferric sulphate and lime. On the basis of the information obtained from the environmental audit process an alternative water treatment and reuse system incorporating 51% reduction in the water consumption with 32% less off-site discharge has been suggested (Thomas, 1995).The second case history is concerned with the storm water management at a mine situated in the Illawarra escarpment where only 20% of the wastewater generated in the colliery is discharged off-site. Computer modelling of the storm water system showed that 75% of the clean runoff becomes contaminated through poor management practices and causes the process wastewater treatment system to fail in wet weather. Suggested improvements include relatively simple alteration to the coal wash filtration dams which are expected to reduce the periods of inefficient operation of these dams by 95%. The use of storm water diversion channels and detention basins can reduce the overflow volumes by 70 - 100 % for a ten year ARI (Average Recurrence Interval) storm event (Wingrove 1996).

Jan 1, 1998

Australia today is one of the leading countries in the fields associated with the mineral industry, an industry which accounts for over 50% of overseas income and revenue to government. This is no accident. In order to be competitive in what was recog- nised very early in the country's history as a highly profitable busi- ness, the Australian mineral industry (mining, extractive and refining metallurgy) has traditionally been very innovation con- scious, a characteristic which has been evident from the begin- ning of the industry or very nearly so: Australia's geographic isolation and the dispersion of the mineral industry over wide distances made an exchange of ideas difficult and often impossible. One needs only to look at the inaugural address given by Sir Henry Ayers, the first president of the then Australasian Insti- tute of Mining Engineers, in Adelaide on 4th April, 1892 (1) "There is probably no other pursuit which depends more on its productive development and profitable results than in the extent and application of the scientific and mechanical knowledge possessed and exercised by its manager." and "Having in view the value of the mining industry of Austral- asians, they should be urged to apply their best skill with all the scientific and mechanical knowledge obtainable to its future development."

Jan 1, 1988

By Tarrant GC

Cement and resin encapsulated tendons are widely used in the stabilisation of mine roadways. One of the main factors in controlling the efficiency of the reinforcement is the ability of the tendon to generate load in response to rock deformation. The analysis of field data from instrumented reinforcing tendons complimented with extensive laboratory investigations have more accurately defined the mechanisms by which load generation occurs. The role of reinforcing tendon profiles, hole geometry and encapsulation medium properties in controlling the reinforcement stiffness and capacity are discussed. The results of the investigation have implications in both the design of rock reinforcing systems and the optimisation of encapsulation mediums and tendons.

Jan 1, 1992

By Floyd JM, Bultitude-Paul J

The development of a process for the extraction of antimony from materials produced by Greenbushes Tin Limited has been carried out based on theoretical and laboratory studies. The materials treated have included concentrates of tantalite and cassiterite containing antimony at levels ranging from 0.3% to 2%. Roasting under controlled atmospheres is required to stabilise Sb203 rather than the low vapour pressure metal or higher oxide. Sulphidising additives such as pyrite, pyrrhotite or sulphur give enhanced antimony removal from tantalite and cassiterite at roasting temperatures of 900¦ to 1100¦C. Substantial elimination of antimony to levels of 0.1% or less was Achieved.

Jan 1, 1986

University education in Australia is changing, driven by greater market orientation, reduced funding available per student, especially in the higher-cost minerals industry disciplines, and the call for more flexible delivery of subjects and courses to meet changing lifestyles and expectations. The opportunity exists for a true partnership to develop between industry, government and academia that will reshape minerals education in Australia and secure the future supply of the specialists industry needs to maintain international competitiveness. If this partnership does not emerge, it is anticipated that AustraliaÆs somewhat fragmented and unstable higher education system, especially in the disciplines of particular relevance to the minerals industry, will be put under further pressure so decreasing its effectiveness to produce quality graduates. The Minerals Council of Australia in 1998 published æBack from the BrinkÆ, a discussion paper which proposed strategies to build a world class minerals tertiary education system in Australia. Those strategies are now being implemented collaboratively with principal emphasis on the disciplines of mining engineering, metallurgy and earth science and as far as process is concerned, on the necessity to æcooperate to competeÆ. For metallurgy, the challenge is to integrate more closely undergraduate teaching with the existing world-class research centres and to link the tertiary institutions in such a manner that the strengths of all components are harnessed and then made available nationally in major population centres and at remote sites where appropriate. For industry the challenge is to build effective partnerships with the academic community that will enable and assist the agreed course of action to take place.

Jan 1, 2000

The passage of a vast array of new State and Federal environmental legislation over the last couple of years has required many mine operators to sharpen their focus on environmental requirements. Established requirements, such as environmental impact assessment, minimising disturbance and rehabilitation must now be complemented by mine environmental management plans. These may not only require regular monitoring of mine operations and detailed forward planning to prevent or reduce environmental harm caused during mine operation, but annual updating. It is likely that in future these plans will be required to incorporate general principles such as pollution prevention, sustainable development, waste minimisation and conservation of biodiversity and ecological integrity.

Jan 1, 1993

By Hall ST, Miles NJ

Recently an inorganic salt, sodium polytungstate (SPT), has become available that allows the preparation of non-toxic solutions of relative densities up to 3.1. It is relatively expensive and at the higher relative densities achievable, highly viscous. Alternative inorganic compounds may in the future be identified that overcome these limitations. The Australian Mineral Industries Research Association Ltd (AMIRA) has initiated a project to examine possible alternatives. However, it has been found that by the addition of finely divided ferrosilicon to solutions of SPT, relative densities of up to 4.0 can be achieved. A laboratory technique for density fractionation of sized mineral samples utilising this finding has been developed. This is currently being extended to study the potential applications of such liquids and suspensions in dynamic systems for mineral, coal and recycled waste separations.

Jan 1, 1993

By M Byrne, P Newman, M Lindqvist

SomincorÆs Neves Corvo Mine, one of the largest copper producers in Europe, is currently constructing a paste backfill plant in order to replace cemented rockfill in its bench and fill stopes and possibly replace hydraulic sandfill in the drift and fill stopes. A 250 m flow loop was constructed at the mine and the flow properties of various paste blends were investigated. Cycloned tailings and total tailings were both pumped successfully as pastes and were also combined with waste rock for additional testing. The pressure losses in 102 mm and 154 mm diameter pipeline were recorded at flowrates up to 60 m3/hr and are presented at slumps from 120 mm to 250 mm. The data showed the sensitivity of paste mixtures to slight changes in consistency, confirming the need for accurate control during paste production and distribution. The flow results clearly showed the different paste behaviour between cycloned and total tailings pastes and the change in properties at low and high slumps. In addition to pressure loss data, strength testing was done on 38 mm and 82 mm diameter samples. Further strength testing is ongoing at the mine using fly ash as a supplement to cement, reducing the overall binder cost. Preliminary engineering for the underground distribution system is briefly discussed, with reference to the siting of the plant. The Neves Corvo Mine is particularly shallow and alternative methods to pumping were sought in order to ensure sufficient hydraulic head for underground distribution. The comparison of options had to take into account the capital and operating costs, the operation of the plant and the impact on the future expansion of paste fill utilisation at Neves Corvo.

Jan 1, 1998

The Directional Drill Monitor (DDM) is an advanced instrument for real time in hole surveying. It was developed by Du Pont (Australia) to suit Australian gassy coal mining conditions. The instrument consists of three units: i. Down hole transmitter ii. Acoustic transducer iii. Data receiver processor unit (i.e. up hole unit). This paper describes the function of each unit in detail and highlights the importance of the DDM in long hole drilling efficiency. Surveying is carried out independent of hole depth. Each survey takes 2-3 minutes to complete, the frequency of surveying to control borehole trajectory is determined by the accuracy required for a particular hole.

Jan 1, 1992

The use of operational research in mining is illustrated by simple examples of the techniques of simulation, linear programming, theory of sampling, and experimental design.Statistical simulation of the delays in answering telephones was used to compare the efficiency of alarm systems in collieries, and to determine stock control policy for a bin in mucking, filling, and tramming operations. Linear programming was used to help minimize transportation costs between collieries and washeries. The theory of sampling was applied to separate and balance the components of error introduced at the' various stages in the collection and reduction of routine samples of coal, and to the assessment of errors of estimates of grade in orebodies from drill samples. 'l'he principles of experimentaldesign were used to compare wear of different conveyor beltings and costs of battery and diesel locomotives in underground transport.INTRODUCTIONIn operational research some of the procedural techniques and professional attitudes of mind found among scientists and, in particular, mathematicians and statisticians, are applied to operational problems in industry ranging from policy making in the broadest sense to the humblest sampling procedures. These apply in mining equally with other industries.Anyone who reviews a procedure critically and in a systematic way may legitimately claim to be doing operational research. On the other hand, what is found in books on operational research is usually a collection of mathematical and statistical techniques which, though forming only a corner of operational research activity, illustrate the novel approaches to problems which characterize the discipline and which would probably not occur to the un...

Jan 1, 1962

The recent trend of installing flotation cells with volumes as large as 200 m3 in concentrators is driven mainly by economic considerations such as lower capital, operating and maintenance costs. Despite the economic advantages, the metallurgical benefits from these large cells have not yet been fully realised by the industry. This is mainly due to the lack of understanding of cell operation, viz cell mixing and hydrodynamics, gas dispersion and froth transportation behaviour in large cells. There is still no rational basis for selecting optimum cell operating conditions and down-the-bank operating profiles. The relationship between cell operating conditions and metallurgy is not well established. This has resulted in poor utilisation of cell capacity in many operations. The present trend of installation of fewer cells in a bank requires each cell to be operated very efficiently. Optimisation of cell operation provides an opportunity for significant metallurgical improvements in a flotation circuit with minimal capital expenditure. Extensive work on optimising of cell performance has been carried out at various Teck Cominco operations in Canada, Peru and USA. Three different levels were involved in this work. The first level was aimed at identification of cell operating conditions for optimum mixing and hydrodynamics, gas dispersion, entrainment and froth flow behaviour in individual cells. The objective of the second level was to identify the optimum bank operating profile for cells down the bank in a circuit. The third level then focused on controlling these cell operating conditions and bank operating profiles for tighter control of concentrate grade and recovery for optimum bank metallurgy. This paper presents some of the major findings at all three levels and demonstrates the importance of each level in optimising the performance of flotation banks installed with large cells.

Jan 1, 2005

By Fraser C. J

The township of Yalloum was established in 1921 to provide accommodation for the work force on the sites of the power station and open cut which were to become the basis of Victoria's electricity industry.A company town, Yallourn flourished, and in its heyday in the 1950s the township had a population in excess of 5500 residents.However the town was sited over a valuable coal field. In the 1960s, studies conducted by the State Electricity Commission indicated that excavation of this coal as a continuing development of Yalloum Open Cut was the optimum choice to meet the growing energy needs of Victoria. Operation in what became known as the Township Field commenced in 1979 and the completion of the overburden stripping was successfully achieved on target in 1991.

Jan 1, 1992

Manganese ore has been mined from the Peak Hill Gold- field since 1948 and from the Pi'lbaraòGoldfield since 1954, and it is probable that some deposits- In and, near the Phillips River Goldfield will be mined at a future date', There are also several million tons of mariganiferous ;naterial which is too low in manganese. .co.ntent_ for . present requirements. The manganese deposits¦of Western Australia are mostly superficial. They hav' been formed during the Cainozoic Era by supergene enrichment ò6f Precambbrian: manganiferoius sediments, and by deposition from -solution on, or'in caves in, the Cain- ozoic land surface. The manganese in solution was derived from the weathering of Precambrian manganifer.ous s.edimexsts, None of the deposits are of hydrothermal origin, nor are they related to igneous rocks in any war, other than as ultimate source rocks. There is ho evidence-'t.o.:sugge,st that meta- morphism has been responsible for.the emplacement of any deposit. The tenor of the ore varies'aec'ording'to the quantity of gangue in the orebody and- also to the nature of the part- icular ore minerals. The main ore.mine.rals are the oxides pyrolusite and cryptomelane and the 'o'xide-silicate braunite. The main gangue minerals are hematite, limonite and quartz. The deposits of high grade oreò(-above.45 per cent Mn) range in size from 50 tons to many thousands of tons but most of them are in the 500-5,000-tons r .nge .

Jan 1, 1964

By McMahon DW, Schapper MA

Hard rock underground mining has been wedded to the drill-blast method of breaking rock. Current practice and technology have focused on greater efficiencies in the blasting and handling of ore, on the basis that thelower costs that come with larger scale operations compensate for the waste dilution associated with the bulk methods. However, it is suggested that new technology is available or is on the horizon that could completely change the shape of hard rock mining in the 21st century. Hard-rock continuous-mining machines, possibly assisted by high pressure water jets, coupled with automated sorting and materials handling systems, could re-orient the miner's focus to winning metal rather than mining tonnes of ore. More continuous mining processes could accelerate the penetration by high technology in the hard rock underground mine, with the potential of greater manpower productivities and lower costs per tonne of metal produced. This new technology will be important in maintaining a competitive supply of metals, given the falling headgrades of the orebodies remaining for development and the increasing market threat from manufactured substitutes.

Jan 1, 1985

The constraints in university courses are lack of hours, high cost of scientific equipment, and poor availability of suitably experienced staff. These have forced the balance away from practical work and towards more theory. Labelling of individuals as either practical, or academic, does not help the inter- change of staff between industry and univer- sities that is necessary to balance idealism and realism. Practical men who do return to universities may lose seniority and find that industry is reluctant to have them back. Academics who specialise too long may concentrate on their research to the exclusion of basic material. It is difficult to operate pilot scale plants in universities because of lack of time, and obsolescent equipment. Small grants from industry might enable tests to be run in research laboratories such as at C.S.I.R.O.. Within universities there may be a need for greater interchange of students among depart- ments, aided by the absence of weighted student unit measurements, as suggested by Aus.I.M.M. and A.M.I.C.

Jan 1, 1984