Search Documents

A paper describing the treatment of the Mary Kathleen uranium ores must necessarily be historical and confined mainly to a review of the four papers which have already appeared. Couche and Hartley (1958) described the development of the treatment process just prior to the commencement of operations in June, 1958. Harris, Boag and Hemingway (1961) described the treatment during the operations, and Wreford (1965) reviewed all aspects of the mine and mill, when operations were suspended in November, 1963. Harris and Steele ('1960 presented a paper especially describing the radiometric sorting operation. Some hitherto unpublished information is also presented in the paper to describe some of the peculiarities of the ore, indicate reasons for the adoption of the treatment flowsheet, and some interesting problems connected with this treatment.

Jan 1, 1968

By A A. Struthers, A D. Farmer

Power ultrasound may be applied to enhancing the processing of minerals. The enhanced performance is achieved through the very localised high-energy release at the mineral surface from the collapse of cavitation bubbles produced by power ultrasound. This gives rise to two effects: initially, the rapid cleaning of mineral surfaces û of oxidation products and coatings of fine adhering gangue minerals û and the attenuation of the boundary layer at the mineral surface during leaching, which allows fresh leachant to contact the surface more readily. Work carried out at CSIRO in conjunction with Tiwest Joint Venture has demonstrated that it is feasible to apply ultrasound to the leaching process in order to enhance the removal of contaminating minerals. When applied to the production of synthetic rutile from reduced ilmenite produced by the Becher process, the use of ultrasound proved beneficial to both the aeration and the final acid leach process. The effect of ultrasound was less marked in the case of the aeration process, once the method of introducing and dispersing the air was optimised. In the subsequent acid leaching step of the Becher process it was found that the application of power ultrasound could reduce leaching time to about one quarter of the time required when only agitation was employed. Projected capital and operating costs, based on currently available commercial equipment, are also presented, and indicate that the use of ultrasound is commercially as well as technically feasible.

Jan 1, 2001

By P Aspinall

Safe work Australia (SWA) has a number of proposed amendments to existing Workplace Exposure Standard (WES) values that may dramatically change how mining workplaces using personal gas monitoring instruments will operate. In consultation with leading gas monitor manufacturers and distributors, an assessment of common Australian alarm settings values and analysis of potential frequency of increased alarm likelihoods has been conducted. This assessment explores the relationships between current monitoring practices, using instruments as health and not just safety tools and identify what will be needed to minimise worker ‘alarm fatigue’ and for common tasks to continue safely. This paper provides the necessary information to aid industry and hygienists to be ‘future ready’ given the likely impact that order of magnitude reductions in time weighted average (TWA) values for NO2, SO2, H2S and other common gases will have on current working practices. Reductions to gas alarm values will provide significant challenges to existing work methods and will require, practical application of the pending future values. Improvements and awareness of instrument capabilities by safety and hygiene professionals will better utilise gas monitors real-time data monitoring capacity and no longer be just ‘safe or not-safe’ instruments. The presentation seeks to promote the practical steps required in setting alarms based on risk consequence and likelihood, increase general awareness of the tools and data available in modern instruments and will enable industry professionals to better manage the challenges of any potential future changes.

Apr 16, 2024

By Lynch AJ, Musgrove NH

The behaviour of chalcopyrite and pyrite in the rougher-scavenger and regrind-retreatment circuits in the Warrego concentrator is discussed. The effects of change in xanthate addition on the separation of chalcopyrite and pyrite is described. The effect of the regrind mill on the (flotation rate of particles containing chalcopyrite and pyrite is discussed with particular reference to the importance of removing sub-mesh particles from the feed to the regrind mill.

Jan 1, 1975

By Scott IR

In stratigraphic orebodies, estimation of footwall and hangingwall location is often of more importance than grade estimation. Contoured grade estimates often produce smeared boundaries and the use of accumulations and thicknesses as variables re-introduces the original problem: location of the point at which the estimate is to be made. The paper introduces statistical and geostatistical techniques for the solution of the problem and illustrates the techniques with a case study from Mount Isa, one of the world's largest producing silver-lead-zinc deposits. Solutions for calculating variograms in orebodies of variable dip, strike and plunge are presented together with relative variograms for individual metals, metal accumulation and orebody thickness. Optimal methods for hangingwall and footwall location are introduced and illustrated with an example. Orebody boundaries are then kriged after which individual metal grades are kriged within the estimated boundaries. The boundary estimates are compared with manually interpreted boundaries and known boundaries in mined-out areas. Grade and tonnage estimates are compared in mined-out areas.

Jan 1, 1986

By A Larsson, K Niiranen

The Palaeoproterozoic Leveäniemi iron oxide apatite (IOA) deposit of the so-called Kiruna type is currently mined by Luossavaara-Kiirunavaara AB (publ.), commonly known as LKAB. The mineralogy of iron oxides, ie magnetite, hematite, maghemite, and goethite is more complicated compared to the neighbouring and more famous IOA deposits of Kiirunavaara and Malmberget. Furthermore, the mineral chemistry of the iron oxides in the Leveäniemi deposit is also slightly different. Especially, the information about the deportment of titanium and vanadium in iron oxides and distribution in the deposit is essential since they can have an impact in the steelmaking process. For this study 50 samples were selected from exploration drill cores and investigated by optical microscopy, FE-SEM-EDS and EPMA at LKAB and the Geological Survey of Finland. Investigations revealed that magnetite is the predominant iron oxide mineral with secondary hematite being the second most abundant mineral. Primary hematite, maghemite, and goethite seem to be less abundant. It should be noted, however, that this investigation focused on magnetite which currently is the only mineral with economic value. Vanadium occurs as a substitution element in the crystal lattice of iron oxide minerals in the Leveäniemi deposit and not as discrete stochiometric vanadium minerals. In the investigated samples vanadium concentration in magnetite ranges from 0.12 to 0.32 wt per cent V2O3 with higher concentration in the southern part of the deposit. Contrary, titanium does not substitute for iron in the crystal lattice of magnetite or secondary hematite (less than 0.018 wt per cent TiO2). It either occurs as tiny inclusions of titanium oxide minerals or as exsolution lamellae of ilmenite in magnetite. The spatial distribution for titanium in the deposit, however, remains unknown. Furthermore, results of this study indicate that alteration of primary magnetite to secondary hematite has had no significant effect on the trace element chemistry of these minerals in the Leveäniemi deposit.

Nov 8, 2021

By R J. Romañach

The theory of sampling (TOS) is now followed in the development of near infrared (NIR) spectroscopic methods for the pharmaceutical industry. TOS has been the guiding light for a two-step approach for spectroscopic composite sampling available for the development of real-time analytical methods for particulate-based industrial processes. The two-step spectroscopic sample composite has been used in the development of process analytical technology (PAT), an important regulatory initiative to improve the quality of pharmaceutical products. The two-step sample composite approach overcomes the low sample volume analysed by PAT methods; one of the key limitations to PAT implementation in the industrial production of particulate-based materials.PAT methods need to be validated demonstrating their accuracy, precision, specificity and robustness. TOS provides a deeper understanding of these validation studies which involve discrete particulate material. The validation of PAT methods is now being performed considering both sampling and analytical errors, while practically all previous method validations only addressed the total analytical error (TAE) of these methods. This has been a crucial impediment for the field of chemometrics as well.PAT is a key element of continuous manufacturing (CM) processes, which are considered an emerging technology capable of increasing the flexibility, agility and robustness of pharmaceutical processes while reducing their costs. The outflow of the continuous process is a 1D lot, and variographic analysis has been shown to discern process variation from sampling and analytical errors in pharmaceutical CM processes. Thus, variographic analysis is a process improvement tool with significant potential for improving CM processes. The possibilities for improving pharmaceutical manufacturing are enormous.CITATION:Romañach, R J, 2017. Theory of Sampling – from missing link to key enabler for process analytical technology, in Proceedings Eighth World Conference on Sampling and Blending , pp 63–68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

The need for formalised geotechnical reporting has not been fully explored at many operations. With the continuing need to provide safer and more efficient workplaces, the requirement for good geotechnical reporting systems (as with other reporting systems) has become of greater importance.Historically, the risk from rockfalls has been the largest cause of fatal injuries in the underground mining industry. The response of the ground to mining is generally poorly documented at many mines. At Olympic Dam, it was found that the existing corporate hazard and incident reporting (HIR) procedure did not record enough specifics about geotechnical issues. A separate and more specific geotechnical reporting process was set up to address this problem.This paper examines the role that geotechnical reporting plays at the WMC Resources Olympic Dam Mine; from reporting and rectifying day-to-day geotechnical issues that affect the operation to documenting and analysing longer term trends.

Jan 1, 2004

By P J. Mienie

The Palaeo-Proterozoic Transvaal Supergroup in the Northern Cape Province of South Africa is host to the largest known resources of high-grade hematite ore on the Southern African continent. These ores are currently being exploited at Sishen and Beeshoek. Hematite occurances on the Sishen South exploration project (some 65 km south of Sishen mine), are at present the focus of an intensive investigation. At both the Sishen and Sishen South deposits, mineralisation is found within lithologies belonging to the Transvaal and Oliphantshoek Supergroups. The Transvaal Supergroup comprises a basal, carbonate platform sequence (the Campbell Rand Subgroup) overlain by thick units of banded iron-formation belonging to the Asbestos Hills Subgroup. The Asbestos Hills Subgroup is unconformably overlain by sedimentary rocks of the Gamagara Subgroup. The latter Subgroup has been correlated with the lowermost unit of the Oliphantshoek Supergroup. The Sishen and Sishen South deposits are located close to the western margin of the Kaapvaal craton and have been subjected to intensive, structural deformation. Both localities have undergone folding, faulting and thrusting. Early regional tectonism (2400 - 1700 Ma) played a critical role in the genesis and preservation of the ores from younger erosive events. At both deposits, four similar iron ore occurrences have been recognised. The ores have developed in specific depositional environments and hence display unique physical, chemical and metallurgical properties:The bulk of the high-grade hematite comprises laminated and massive ores, which are found in the upper parts of the Asbestos Hills Subgroup. The laminated and massive ores are best developed in basinal and pseudo-graben structures. Collapse breccia ores of medium- and lower-grade are preserved within deep palaeosinkholes. The sinkholes have developed within the dolomites of the Campbellrand Subgroup. Lower-grade conglomeratic and gritty ores constitute the remainder of the deposits. These ores are found in the overlying clastic succession of conglomerates, shales and quartzites belonging to the Gamagara Subgroup. Although, there are many stratigraphic and lithological similarities between the Sishen and Sishen South deposits, there are also important differences, which will impact on the profitable exploitation of the ores. The most striking contrast between the deposits is their size and geometry. Sishen mine is a single pit operation with an opencast mineable reserve of 895 Mt. The Sishen orebody is thicker, more continous and significantly larger than the Sishen South deposit. The Sishen South deposit has a potential opencast reserve of 228 Mt. It comprises a number of small and narrow, isolated orebodies, spread over an area of ¦64 km2 . There is a significant difference in grade between the deposits. On average the orebodies of the Sishen South deposit have a higher iron content (+0.25 per cent Fe), less potassium (- 0.090 per cent K2O) and less phosphorus (-0.019 per cent P). The Sishen South deposit has less interbedded shale in the laminated and massive ores. The footwall of these high-grade ores is a light-density, intrusive sill, compared to banded iron-formation at Sishen. With a proposed heavy-medium separation plant at Sishen South, the impact of dilution on product grades is expected to be less than that currently experienced at Sishen.

Jan 1, 2002

Pipe Jacking has been a recognised method of tunnelling in the U.K. since the early 1950's, although I understand that pipes were pushed blind by the soldiers in the first World War from trenches on the Allied side to, or adjacent to, trenches on the German side, thus allowing explosives to be used with a certain element of surprise! 'However, on its more conventional to the U.K. in the 1950's, Pipe Jacking made considerable inroads into the tunnelling market place as an alternative to timber supported headings. This success was, unfortunately, fairly short lived because, owing to its simple method of operation, contractors paid insufficient detail to the engineering (or surveying) aspects and as such the system soon had a bad reputation for unreliability and lack of accuracy. Due to these failings, the market was not exploited and, therefore, there was a lack of investment by contractors, pipe manufacturers and also by any client, or research organisation, which is client associated. The effect of this meant that the system stagnated for a number of years and was used generally only for short crossing work (i.e. railways, canals and motorways), and then only in good homogeneous ground. Albeit, a limited number of full scale sewage disposal contracts were carried out, but with the lack of knowledge and experience of the clients, contractors and suppliers, (particularly the pipe suppliers), no reasonable success, either physical or financial, was achieved on any such contract.

Jan 1, 1987

By D R. Swinbourne

In the recent past a number of smelting plants were commissioned in India to supply the rising demand by domestic steelworks for manganese-based ferroalloys, and they enjoyed cheap electric power and readily available high-grade manganese ore. Presently, the cost of electric power is much higher than in some neighbouring countries, there continues to be poor transport infrastructure and the prices of high-grade manganese ore have increased. Additionally, the Indian Government has opened its economy to the outside world, resulting in the import duties on ferroalloys being drastically reduced. In this paper the current situation in India will be detailed, the electric arc furnace and blast furnace smelting methods for ferroalloys compared and proposals for the construction of a new ferromanganese blast furnace in India outlined. The future of ferroalloy smelters in India will be assessed and actions which could be taken to improve their position discussed.

Jan 1, 2000

The Channel Tunnel is an outstanding example of an undersea tunnel and its design illustrates most of the unique features of this type of tunnel. The marine site investigation was partic- ularly vulnerable to adverse weather conditions. To minimise this interference the time the drilling vessel was required to remain on station was kept to a minimum by expediting the drilling and the insitu tests as far as was practicable. To avoid additional unforeseen costs the contract documents were framed to take particular account of marine practice. The limited access at the coast line meant that for economy, maximum tunnel advance rates had to be attained. Ground excavation, handling and disposal methods and the provision of the lining were optimised and equipment specified in detail to ensure that no one com- ponent was delayed by a lack of capacity or mechanical failure in any other.

Jan 1, 1976

By R Farnf, M Pegden, S Hosein, T White

A number of theoretical papers have been published outlining the use of electronic detonators to limit peak particle vibrations levels, but few empirical studies have been undertaken and even fewer examples have been published of the use of such technology in the aggregates industry. This paper gives a summary of the research work carried out at two limestone quarries in the North of England, where a series of blasts were used to compare and contrast the use of electronic and non-electric detonators. The majority of blasts were carried out using the same burden, spacing and decked charge weight loadings. A methodology was established that could be used to reduce the peak particle velocities (PPVs) at two or more specific locations by using single-hole blast vibration signatures in conjunction with specific electronic detonator timing intervals. The initial study concluded that this was only possible if single-hole signature blasts were periodically recorded to establish the shape of the correct vibration envelopes as properties were approached. These wave envelopes could then be used as the basis for choosing the specific electronic detonator timing intervals to give the lowest PPV for the properties or locations concerned. This methodology was then used in the second study to access a large volume of aggregates adjacent to a working railway tunnel. The financial benefit for the company was to convert these additional tonnages of rock from being a resource to an exploitable reserve. The project involved careful blast design and the instrumentation of a number of boreholes to enable the results of blast monitoring exercises to be compared with predicted PPV results. The iterative process involved the vibration results being uploaded into æBlast LogÆ (an expert blasting database system developed by the Blasting and Environmental Research Group at the University of Leeds) and analysed to produce predictions ready for the next blast.

Jan 1, 2007

By P Pieterse

Kumba Iron Ore Ltd is currently commissioning the Sishen Expansion Project (SEP) û a brownfields project on the Sishen Iron Ore Mine located in the Northern Cape Province, South Africa. SEP is designed to produce 13 Mtpa of product from 21.7 Mtpa of ROM feed. The beneficiation section of SEP employs jigs to process narrow size fractions in the 25 x 0.8 mm size range. The -0.8 mm fraction is screened out ahead of the jig plant and rejected as waste without any prior beneficiation. The processing of this fraction was not included in the early stages of SEP development because no suitable beneficiation or dewatering technologies could be identified within the time-frame required to implement SEP. This paper presents the SEP 1B project, ie the metallurgical and process engineering study that was done to evaluate the techno-economic viability of processing the -0.8 mm material of SEP. To support this evaluation, metallurgical bench scale testwork was done on selected samples characterising the material types used in the SEP for gravity concentration beneficiation. Subsequently, pilot testwork on a 300-ton bulk sample demonstrated that an integrated teeter-bed/spiral circuit could be used to successfully beneficiate the -0.8 mm fraction. The study has established the viability of the proposed process and has concluded that approximately 390 000 tpa could be produced and added to the SEP fine ore product without violating the applicable product specifications. The proposed process has been designed to be implemented in modular units in order to facilitate implementation and ensure future expandability. Based on the recommendations of the study, approval has been granted for the detail design feasibility study. Production is scheduled to commence in the first quarter of 2010.

Jan 1, 2008

By Gochin RJ

This paper focuses on measures of the economic significance of mineral exploitation and processing activities, such as beneficiation, refining and smelting. Empirical measures are suggested to quantify the relevance of the degree processing within a nation's mineral industry. The most useful, based on the input-output econometric framework, are used to establish the magnitude of links between the mineral industry and its satellite activities and for the appraisal of large, non-marginal projects. The input-output impact analysis is refined to allow for country specific behaviour and synthetic indices for the appraisal of investments in the mineral sector are developed. These indices are further improved with the introduction of shadow prices to incorporate socio-economic issues. They are useful to direct mineral policy decisions and several investments towards the most promising objectives for national goals. Finally traditional methods for the appraisal of small scale, marginal, mineral projects are assessed where local impact and regional development issues are more relevant than national ones.

Jan 1, 1993

By M Runkel, J Hammerschmidt, A Holmstr÷m, A Charitos, J Gnntner

"Roasting of sulfide concentrates and refractory ores is an important process step in the production of metals and chemicals. Sulfides of iron, zinc, copper and other metals are oxidised with air between 600 and 1000¦C into metal oxides or sulfates and gaseous sulfur dioxide. Roasting of gold concentrates and ores is a typical processing step used to produce a porous calcine suitable for cyanide leaching. During roasting, elements posing problems are removed through: oxidation (carbon, sulfur, arsenic and antimony) or volatilisation (mercury, chlorides and tellurides, as well as arsenic and antimony).This paper focuses on the environmental aspect of roasting using fluidised bed technology. The approach is to show that roasting is an attractive solution for refractory ore pretreatment since, on the one hand, it is an efficient technique yielding high gold recovery rates, while on the other it is able to comply with current stringent international environmental regulations. In that respect, roasting is compared to alternative processes, ie pressure oxidation (POX), bio-oxidation (BIOX) and ultra-fine grinding (UFG). Roaster high gold recovery rates are ensured through roasting-leaching test work, which allows the derivation of respective roasting parameters that are easily achieved in an industrial plant. On the other hand, key elements of the roasting process are analysed, which make it an efficient and sustainable technology, ie the possibility for energy recovery, the removal of off-gas impurities during the different gas cleaning steps (handling of arsenic, mercury emissions and further hazardous dust and gas emissions) and the treatment of the SO2-gas in order to produce sulfuric acid, and finally the treatment of the effluent produced. The processÆs environmental aspects are summarised by listing roasting emission values that comply with international regulations.CITATION:Charitos, A, Runkel, M, Gnntner, J, Holmstr÷m, A and Hammerschmidt, J, 2013. Roasting - a study on environmental aspects, off-gas, effluents and residue treatment, in Proceedings World Gold 2013, pp 509-518 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

By P Lotz

With the recent increase in environmental awareness, gold mining companies are fast becoming signatories of the International Cyanide Management Code (ICMI, 2007). The objective of the Code is to improve the management of cyanide used in gold mining and to assist in the protection of human health and the reduction of environmental impacts associated with the use of cyanide. In particular the code specifies the following cyanide concentration limits: 50 ppm WAD cyanide in a tailings storage facility, 0.5 ppm WAD cyanide for effluents, and 0.022 ppm free cyanide or 0.022 ppm WAD cyanide as surrogate in the post mixing zone of river discharge. Weak acid dissociable (WAD) cyanide refers to those cyanide species liberated at a moderate pH of 4.5, such as HCN(aq) and CN-, and the majority of Zn, Cd, Cu, Ni and Ag complexes with low dissociation constants. It is potentially toxic to humans and animals. Gold plants using cyanide should ideally measure WAD cyanide online and destroy WAD cyanide in excess of the applicable limits to ensure compliance with the Code. Mintek has recently developed an online WAD cyanide analyser (WAD Cynoprobe). The WAD cyanide analysis technique is based on the use of a ligand exchange reagent that liberates WAD cyanide bound to metals such as Zn, Cd, Cu, Ni and Ag. The ligand exchange reaction is represented by the following chemical equation: Metal(CN)X + yLigand ↔ Metal(Ligand)y + xCN- The plant filtrate is treated with a ligand exchange reagent, to liberate WAD cyanide, before measuring the free cyanide concentration via amperometry. The WAD Cynoprobe measures both free and WAD cyanide concentration. Its fast analysis time, approximately five minutes, makes it suitable for use in the control and optimisation of the cyanide destruction and recovery process. The instrument has proven accurate and reliable in the analysis of synthetic copper, nickel and zinc cyanide solutions made up in the laboratory as well as under industrial gold plant conditions during various trials. The WAD Cynoprobe has gained widespread commercial acceptance and is currently implemented on nine gold plants around the world.

Jan 1, 2007

By W Zirima

A detailed, mine scale non-linear numerical model of Rosebery mine has been built for the purpose of simulating life-of-mine global deformations. The model was calibrated using observations of displacement and damage, and was then used to investigate the correlation between dissipated plastic energy (DPE) and seismic event occurrence. The study is unique because the seismic data was collected over a relatively short period using a temporary portable seismic system. It is the intent to undertake significantly more work, but the analysis of limited data shows that a very good, non-linear relation between DPE and event probability is present. The observed correlation is consistent with measurements from other mines where more data was available. With more data, the strength of the correlation will allow the DPE analysis to be used during the design and sequencing phase of planning to better design the mine to minimise seismic hazards.

Jan 1, 2008

Mackenzie (1968, p. 167) inferred that amphibolitelayers grade into and may be correlated with footwall Potosi gneiss where it is thin under the thickest development of the "lead lode" in the New Broken Hill Consolidated mine, Broken Hill. This gradation from amphibolite to Potosi gneiss is tacitly assumed in many of the constructed crosssections of the southern end of the orebody, where amphibolite and Potosi gneiss, defined in hand specimen, are correlated in adjacent drill holes. The basis for such correlations is the observation that some amphibolites in drill core lighten in colour from black to grey along the core and grade into an unlayered rock containing conspicuous pink garnets, which resembles Potosi gneiss (for descriptions of Potosi gneiss see Andrews, 1922; Gustafson, BurreIl and Garretty, 1950; Carruthers and Pratten, 1961;\Ternon, 1969).Average chemical compositions of "footwall" Potosi gneiss and "upper" amphibolite (Hawkins...

Jan 1, 1972

Geomechanics is one of the more specialised aspects of site supervision on a major tunnell- ing project. The controlled deformation of a rock mass as a result of tunnelling and the knowledge of loading of temporary and permanent underground supports are important for safe, economic construction. These basic parameters depend on the construction method and sequence and the geological conditions through which a tunnel is driven. Thus geomechanical monitoring during the construction phase provides feedback to a design team and allows any revisions to a design to cater for local conditions not revealed by earlier investigations. Detailed geological mapping is an integral part of geomechanics in the construction phase. It serves as a monitor on pre construction predictions and also forms part of the as- constructed record. If conventional excavation-techniques are adopted, geomechanics can provide a service of blast' vibration monitoring of surface structures in urban areas.

Jan 1, 1976