Search Documents

By L Semenyna, W Douglas

Gold is often present in solid solution with pyrite in the Carlin Trend. The presence of organic carbon along with gold hosted in sulfide, referred to as double refractory ore, requires that ore with high carbon-in-leach (CIL) preg-robbing potential and poor leach recovery is routed to a roaster. During roasting, the pyrite is oxidised to (ideally) form hematite (Fe2O3), and the gold that was present as solid solution in the pyrite forms colloids within the hematite. The ideal texture of the produced hematite is porous to allow for the penetration of cyanide for gold dissolution. Temperature and other conditions of roasting, as well as ore characteristics (pyrite mineral associations, arsenic) can affect the texture and the type of iron oxide formed. Many of these alternate iron oxide minerals result in incomplete leaching. Comprehensive gold deportment studies have proven that the majority of the gold losses in Barrick GoldstrikeÆs roaster leach tailings occur within the iron oxides created through the roasting process.The iron oxide phase that hosts the majority of the gold in tailings is in the form of by-product maghemite (?Fe2O3), which is highly magnetic. Barrick Goldstrike has designed a magnetic recovery circuit to capture these iron oxides, and with subsequent reprocessing, recover the lost gold. Pilot plant results and analysis using scanning electron microscope mineral liberation analyser (SEM MLA) shows that up to 30 per cent of the gold in tailings can be recovered with a three per cent overall mass pull to magnetic concentrate. This magnetic concentrate can be economically reprocessed, resulting in a three per cent improvement in roaster recovery.CITATION:Douglas, W and Semenyna, L, 2013. Magnetic recovery of gold-bearing iron oxides at Barrick GoldstrikeÆs roaster, in Proceedings World Gold 2013 , pp 79-86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

A Process for the Flotation of Chrysocolla

Sep 13, 2010

This paper deals with the extension of Post Office telecommunications (telephone, data, leased private lines etc.) network to mining communities in remote areas of Australia. The evolution of the "Spur Line" policy and its application is referred to together with comments on the engineering of telecommunication Facilities.

Jan 1, 1973

By C Vejrazka1

The occurrence of airblasts is one of the principal mining hazards in caving operations between the time of cave establishment and breakthrough of the cave to surface. As such, it needs to be managed continuously and risk assessments need to be reviewed on a regular basis for applicability to changing conditions. The likelihood of an airblast occurring is based on a range of geotechnical factors over some of which engineers on-site only have limited control. However, the impact of an airblast to the underground mine, if it does occur, can be managed by following established safety guidelines for the production from the cave.This paper outlines how the Caving Airblast Simulation Tool in Ventsim was used to determine a risk management strategy for a sublevel and a block cave at a mining operation in Australia. The block cave has a footprint of 14 500 m2 with the extraction level located 1250 m below surface while the sublevel cave currently has a footprint of around 18 000 m2 operating between 660 m and 800 m below surface. Both caves are currently in their early operational periods. The risk analysis provided valuable information for the production planning of the caves including confirmation of extraction ratios for the block cave undercut, locations of airblast walls and maximum allowable air gaps for different muck pile heights to ensure safe operation is achieved.

Oct 12, 2022

By McPherson M. J

This paper describes a major ventilation study for the expansion of the El Teniente mine operated by Codelco, Chile. El Teniente is one of the world's largest under- ground mines. The design effort was under- taken in three stages and involved a partial mine ventilation survey with network simula- tion, detailed stope ventilation investiga- tions, and design of the entire mine ventila- tion circuit based on production plans to achieve 112,000 tons per day by 1995. The partial ventilation survey provided values of representative friction factors and resistances for typical ventilation raises and airways. These values were used to conduct detailed modeling of the block caving levels to investigate the most cost effective and practical means of providing the required ventilation. The results of these analyses were extrapolated to the proposed expanded mechanized zones.

Jan 1, 1988

By G Cavanough, A Olsson, J Rock, A C. Torrance

There are various methods currently in use to determine detonation performance of bulk explosive products including velocity of detonation (VOD), high speed photographic analysis, fragmentation analysis and unconfined detonation of samples. For assessment prior to detonation the current practice is limited to a measurement of cup density. This paper presents additional techniques that have been developed to provide measurement and assessment of bulk explosive products. Techniques applicable prior to detonation include a mobile laboratory to allow on-site chemical and physical analysis of sensitised products and ‘in-hole density’ measurement to monitor the in-hole density during sleep time. Assessment of detonation performance is achieved using detonation pressure sensors. These sensors allow measurement of detonation pressure, average VOD, propagation time and magnitude of the pressure induced in the explosive column by detonation of adjacent blastholes.CITATION:Cavanough, G, Torrance, A C, Rock, J and Olsson, A, 2015. Measurement and assessment of bulk explosive products, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Feng, G C. Lukey, J S. J, R R. Dagastine

An ongoing challenge in the coal industry is pyrite removal using the flotation method for fine particles. The use of a æseparation in frothÆ (SIF) technique to recover coarse particles of up to a few millimetres in size has presented a potential solution. However the commercial success of SIF is still limited due to the poor understanding of the separation mechanism. The particle floatability in SIF is determined by the constructive or destructive stresses resulting from the forces exerted by the particle on the bubble films. Hence, the surfactant properties and the mineral characteristics (eg hydrophobicity, shape, etc) are the key factors that control the interaction between the particle and froth. In the present work, the interaction forces between different particles (ie crushed glass, pyrite and coal) and a single air bubble are measured in a non-ionic surfactant solution (pentaethylene glycol mono n-dodecyl ether, C12E5) using an atomic force microscope (AFM). Experimental results show that the interaction is primarily dependent on the contact angle (ie the degree of hydrophobicity of the minerals). For crushed glass, the transition from repulsion to attraction was observed as the contact angle increased. As the concentration of C12E5 increased, the adhesion force was suppressed due to wrapping effect. For coal and pyrite with much higher hydrophobicity, long-range attraction was observed. The effect of shape factor was only visible at high surfactant coverage where sign of destabilisation became noticeable on the retracting force curve. These results provide a fundamental understanding of the direct interaction forces of a complex real system between an irregular particle of either crushed glass, pyrite or coal and a single air bubble. Theories developed for interpretation and modelling are thus far based upon the study of ideal systems of glass or polystyrene spheres and an air bubble and were incapable of explaining the interactions in complex real systems. The presented measurements were a first approach to the problem of real mineral-bubble interaction in flotation systems. Thus, the results can only best be interpreted semi-quantitatively.

Jan 1, 2005

The brown coal deposits of the Latrobe Valley are ideal for open cut mining and this method has been used since the start of coal winning in 1894. Operations at the main Yall9urn open cut commenced in 1922, but after a few years the main excavators were replaced by German continuous excavators and subsequent developments of Yallourn and the newer Morwell open cut have been based on this type of plant. The reasons for preferring continuous to intermittent excavators in the Latrobe Valley are indicated in this paper.Under the pressure of post-war conditions, and from their long experience and ability, German engineers have recently made substantial improvements in their continuous excavators and these developments have been enhanced by some American innovations. These changes have extended the economic limits of open cut mining and also serve to emphasize the close inter-relation between the nature of coal and overburden deposits, excavator design and methods of operation.As an aid to descriRing recent excavator developments, this interdependence is demonstrated by means of diagrams which show typical methods of operations, together with examples of actual machines using these methods. The types of excavator dealt with are mainly those in use at, or destined for Yallourn or Morwell open cuts, together with additional types used in U.S.A. and Western Europe. For completeness, and also because they will continue in service at Yallourn and Morwell for some years, rail-mounted dredgers have been included in this paper even though in Europe they are now regarded as obsolescent.Explanations are given of how the intrinsic qualities of Latrobe Valley brown coal and overburden have sometimes prevented overseas plants from operating with the full efficiencies and/or in the methods visualized by the manufacturer, and references are made to the modifications and investigations being undertaken to overcome these problems.A compresensive bibliography is given. Dates shown on illustrations are not commissioning dates of the plant concerned, but the year when photographed.

Jan 1, 1960

The banded iron formations "jasper bars," jaspilites, banded hematite quartzites or banded ironstones, etc., as they have. variously been termed in Western Australia, constitute one of the most striking features of the Pre-Cambrian in this State. They occur in at least two distinct divisions of the Pre-Cambrian, viz., in horizons interbedded with quartzites, shales and thin bedded dolomite in the N~llagine (Proterozoic) Series; and amongst the Older Pre-Cambrian rocks, associated with the metamorphosed sediments of the Jimperding-Chittering Series, the Yilgarn Whitestone Series and the Mosquito Creek Series, and interbedded with metamorphosed basic lavas, tuffs and sediments of the Older prenstone or Kalgoorlie Series.In the Hamersley Ranges in the north-west of Western Australia banded ferroginous cherts are well developed amongst the horizontal sediments of Nullagine Age. These iron formations have recently sprung into prominence as they have been found to form the host rocks for important deposits of· blue asbestos. They are closely comparable with the unique crocidolite-bearing banded ironstones of the Cape Province, South Africa, and have been described elsewhere in some detail by the writer. (1) t .The banded iron formations with which it is intended to deal principally in the following pages, form most abundantly in the Central and Eastern Goldfields of Western Australia where they form portions of the Older Greenstone or Kalgoorlie Series of auriferous rocks. In these regions their chemical inertness and physical hardness provide considerable resistance to the agents of erosion and consequently they frequently stand out in strong topographic relief in otherwise monotonously flat or gently rolling country. These banded-iron formations have proved of considerable direct economic importance in the goldfields and in other portions of the State because of thei!! associations with 'gold, iron -and to' a lesser extent, manganese; whilst indirectly because of their peculiar nature, form and topographic prominence, etc, they have been of tremendous assistance to the field geologist both in the practical application of methods of geological mapping and in the' elucidation of geological structures. Finally, they have recently acquired a new importance in the specialised search for ore-bearing lodes or for structural information over areas of soil-covered country, as their form and composition make them ideal subjects for the use of either electrical or m!1-gnetic methods of geophysical prospecting.

Jan 1, 1941

By M Griffiths

This paper outlines an approach to high solids slurry pipeline design with data generated from a closed pipe-loop test system. The pressure and flow rate data generated is used to develop a pseudo-shear diagram for the purposes of system design. Following this approach enables the design of a full pipe flow system maximising system life and reliability. The alternative free fall system is explained and the disadvantages highlighted.Environmental and social considerations are discussed; mainly water and land use, and how designing for high solids slurry pipeline systems can be used improve these aspects of a mining project.Also discussed is how the use of high solids slurry pipeline systems can help to mitigate the risk associated with surface tailings storage facility failure, with the Bulyanhulu project used as a positive example.

Aug 8, 2011

Goldfields (Tasmania) Limited operates a small, high-grade underground gold mine on the West Coast of Tasmania, 30 kilometres north of Queenstown. The main orebody, Zone 96, was discovered in 1989, with major development work commencing in 1993. The mine was officially opened in July, 1996. Initial production came from a shallow orebody known as the Sill Zone, some 50 - 150 m below surface, which was accessed by a 1 in 8 decline. Zone 96 lies between 350 m and 550 m below the surface and is accessed by a 402 m deep, 3.2 m diameter internal shaft from the collar level located 100 m below surface. The main ore extraction system in Zone 96 is mechanised cut and fill, using high density paste fill. Run of mine ore and waste are hoisted in a single 5.5 tonne overturning skip, then trucked from the underground collar to the gold plant ROM pad or waste dump, respectively. Ground conditions in the mine vary with orientation and proximity to major faults. The gold is contained in a sequence of strongly altered volcanic rocks adjacent to the Henty Fault. Most of the gold is contained in massive quartz, ranging in width from 0.5 m to 7 m, which has been subjected to substantial faulting. Average mineable grade is about 27 grams gold per tonne. Ore reserves in 1996 proved an initial mine life of approximately 4.5 years at 90 000 ounces gold per annum, with significant potential for additional resources from extensions to Zone 96 and adjacent zones. The lease is located in an environmentally sensitive area and a very high standard of environmental management is an essential part of the operation. This paper describes the relevant aspects of mining at Henty including grade control, ground support, backfill placement and environmental management.

Jan 1, 1998

The growth of "Unit Load-cargo handling technology in world cargo lin- er trades over the last decade has cre- ated a situation in which special pur- pose-vessels (cellular container ships, roll-on/roll-off vehicle deck ships and Lash type vessels) are rapidly replac- ing conventional cargo ships, the principal means previously available for transporting heavy lifts. Consequently heavy lift traffic has tended to accumulate awaiting ship- ment, especially where discharge is required in "off beat" locations. A partial solution to this problem will be provided by new and small but exceptionally versatile ocean going heavy lift carriers now finding their way into world trade routes. These new ships combine extremely high lifting capacity, high manoeuvreability and exceptionally shallow draft with bow and stern Ro/Ro capability. They can handle rolling loads of exceptional size and weighing up to 1,000 tons Each. But the problem is a far larger and more serious but essentially a domestic one. Major industrial pro- jects in Australia will require pro- gressively heavier and larger plant and construction sites are becoming much more inaccessible. Whereas these new ocean going heavy lift carriers have ample capacity to satisfy part of the total transport requirement, there is clear evidence to show that domestic transport resources have little if any potential for increase in capability at the same rate as demand or at the same rate as sea transport facilities. Resolution of the larger problem is within reach but only through a pro- perly co-ordinated approach to future planning for the overall needs of large scale projects on a national basis. This co-ordinated approach must involve Federal and State government transport administrators, railway and highway authorities, shipping and road haulage interests and finally the planners of the projects which require these improved heavy haulage services.

Jan 1, 1973

By J Kelly, C Kelsey

The Autogenous Kelsey Axial Displacement (KAD) mill is essentially a short retention time centrifugal mill, designed to effectively harness extraordinarily high concentrations of input energy for efficient particle size reduction. The mill which has an operating duty band extending from primary to ultra-fine also has the unique capacity to generate fine and ultra-fine products from single stage size reductions of either coarse or fine mineral feeds, in both wet or dry operating modes. This paper covers developments following a recent optimisation programme which confirmed that mill shell speed and the velocity differential between the shell and the rotating internal disc assembly tips could be optimised in relation to specific energy for a given feed rate and feed size providing the product size remains constant. Subsequent test-work further demonstrated the versatility of the mill with duties ranging from the removal of surface contamination associated with heavy mineral concentrate particles to the production of premium ultra-fine talc, from a single stage of size reduction. Open circuit grinding of a rougher gravity concentrate to liberate gold ahead of leaching also highlighted the scope for the application of low cost KAD milling for a range of hydrometallurgical feed preparation duties, which involve fine and ultra-fine grinding.CITATION:Kelly, J and Kelsey, C, 2013. Advanced media-free fine and ultra-fine grinding - The Kelsey axial displacement mill, in Proceedings MetPlant 2013 , pp 152-161 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By A F. Idziak

The aim of the present study was an application of coal optical property measurements for analysis of paleostress field existing in fault zones of the Upper Silesian Coal Basin (USCB) during the coalification of organic matter. Measurements of vitrinite reflectance were carried out on coal samples taken near a hanging stope of the Klodnicki fault. Other samples had been taken in vicinity of the Krzyzowicki fault. The Klodnicki fault is one of the main tectonic discontinuities in the northern part of the USCB. It is postulated that its origin is related to the deep-rooted latitudinal discontinuity in crystalline basement of the basin. The Krzyzowicki fault is located in the western part of the USCB where fold tectonic style dominates. Vitrinite, one of the basic components of hard coal is generally considered as optically anisotropic material. Anisotropy of physical properties is induced mainly by stress, which arranges vitrinite structure. Vitrinite anisotropy can be described by an ellipsoidal model called reflectance indicating surface (RIS) which is a geometrical representation of the optical anisotropy tensor. The investigation of the RIS for vitrinite was carried out on coal samples. The apparent maximum and minimum reflectance values measured for a single vitrinite particle were plotted against corresponding bireflectance to construct the reflectance crossplot. Interpretation of this plot yielded the magnitudes of the RIS three principal axes. The data obtained point to differences in optical anisotropy of coal under the study. The coal samples taken from block tectonic zone near the Klodnicki fault had mean reflectance value of less than 0.80 per cent. Their anisotropy coefficients were about 0.1. Optical properties of coal changed from the biaxial positive in the western segment of the fault to the biaxial negative in its eastern part. It suggests that past tectonic stress was greater in the western part of the zone than in the eastern one. Coal originated from a fold tectonic zone at the vicinity of the Krzyzowicki fault has mean reflectance value much greater than from previous region (ÿ1.20 per cent). Its optical anisotropy coefficient is equal to about 0.07. It suggests that paleostress field was more isotropic. The presented study shows the usefulness of coal reflectance measurements in the analysis of paleostress field existing during coalification process.

Jan 1, 2003

By J Cronin, R Burgess-Limerick, T Horberry, L Steiner

"Automation offers the mining industry great potential for improvements in productivity and safety. However, the experience of introducing automation in other industries has been that the full potential of new technology is not always realised. Designers are surprised, for example, to find that automation does not eliminate human errors. Unwanted and unexpected consequences also arise if the introduction of automation fails to consider how people will adapt to the new technology. A focus on the technical aspects of automation is necessary but not sufficient for success. The potential for improvements in productivity and safety promised by automation will only be achieved if the joint cognitive system that emerges from the combination of humans and automation is designed to perform the functions required for system success. This case study describes the human factors issues associated with the introduction of automation generally, and describes a case study of the successful implementation of loader automation at Northparkes mine.Information obtained through a site visit and interviews with operators, safety staff and the project manager revealed the following strategies for successful design and implementation of the automation system: involve the people who will be impacted encourage constant communication between operators and designers provide operators with essential information avoid providing non-essential information provide the operators with flexibility empower operators to take action take advantage of the new possibilities automation provides.CITATION:Burgess-Limerick, R, Horberry, T, Steiner, L and Cronin, J, 2017. Mining automation human-systems integration – CMOC-Northparkes case study, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 93–98 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By L Teixeira, C J. Greet, P Karageorgos

Pyrite is ubiquitous within copper ores, and presents significant challenges to most operations in terms of its impact on copper sulfide concentrate grade and recovery.Samples of ore containing from 3 to 47 percent pyrite, with nominally the same chalcopyrite feed grade, were collected from a copper mine in eastern Australia for testing. The ores were ground under standard conditions using forged steel grinding media in the Magotteaux Mill® to determine the impact of increasing pyrite feed grade on the pulp chemistry of the system and subsequent rougher flotation response. Attempts were made to correlate the pulp chemical parameters (oxygen demand and EDTA extractable metal ions) with flotation behaviour to determine if one (or more) could be used as a metric to infer metallurgical behaviour.The observations made were then tested under different grinding environments (obtained using more electrochemically inert high chromium) grinding media to determine if they hold true.CITATION:Greet, C J, Karageorgos, P and Teixeira, L, 2015. The influence of pyrite on the pulp chemistry and copper flotation response of a chalcopyrite ore, in Proceedings MetPlant 2015, pp 175–187 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Hargraves A. J

With increasing depth, stresses and stress phenomena are becoming more important considerations in Australian coal mining.A large number of compressive and tensile strength tests was made on coal and rock cubes cut from samples taken in various Australian collieries. In addition, an empirical impact strength test was carriedout on fragments of the same samples, to obtain a correlation with compressive strength.In one colliery, flat-jack measurements were taken to assess stresses in coal ribs and in the roof.INTRODUCTIONBy world standards, some of the New South Wales collieries are approaching depths of cover considered a maximum for bord and pillar the normal Australian coal mining method. Several South Coast collieries are winning coal at depths of about 1500 ft., and future operations are being planned at deeper cover. Some areas of these deep workings produce considerable quantities of seam gas.Phenomena associated with high stress and copious gas under pressure in the seam violent phenoma presenting a danger and a nuisance in mine working - have occasionally occurred, and the phenomena are being investigated as a whole (Hargraves, 1958), and separately as a gas problem (Bolt and Innes, 1959; Hargraves, 1962) and as a stress problem. This paper relates to the latter - to investigations into the strengths of coals and coal measure rocks, and into the stresses in and about coal seams...

Jan 1, 1962

Iron and steelmaking slags have been utilised for a century. All dumps are now exhausted. Because of constraints in establishing new stock yards, all slags have to be utilised immediately. At present, this is being achieved. Only in a situation where there is an increase in pig iron and crude steel production, together with the impact of new residual materials competing from other industries can marketing problems be anticipated.

Jan 1, 1979

By P D. Munro

The spatial distribution of ore with similar processing properties or domains within an orebody may be identified early in the assessment of an orebody to provide a sound basis for later development of the orebody. The assignment of domains in the primary sulfide portion of an orebody is often more difficult than recognition of the oxidised, supergene and related domains usually located towards the top of the mineralised volume. This paper will discuss some approaches to assigning domains within the primary sulfide portion of an orebody. The processing properties of each mining block will be known if the contained domain(s) and their proportions are known. The use of both physical and chemical ore properties to assign the domains is discussed. The domains based on similar processing properties do not necessarily coincide with geological zones assigned by geoscientists. As part of assessing the physical properties of ore, the modal analysis of the ore with respect to the valuable sulfide minerals and the sulfide and non sulfide gangue minerals has to be known, along with the traditionally used elemental assays for valuable and penalty elements. Two scales for determining other physical ore properties will be considered: the mesoscopic scale (examined by human eye) and the microscopic scale (examined via a microscope under high magnification). The strengths and weaknesses of the data obtained at the two scales are discussed in the paper. Broadly, data collected at the mesoscopic scale are much less expensive but the types of data available are more limited. Methods for evaluation of chemical ore properties are also discussed. After establishing a basis for establishing the spatial distribution of domains, variability testing is required to verify the integrity of the designated domains. In contrast, each block of ore in some orebodies has been assessed principally via the results of a laboratory separation on a number of drill core samples or composites from throughout the block, with minimal or no attention to the concept of domains.

Jan 1, 2008

Same-batch and non-blind as well as blind pulp duplicates are often submitted as quality assurance/quality control (QA/QC) control samples to a routine laboratory along with routine assays (and other control samples such as reference material samples). The current ways of interpreting the results of duplicate assays to derive QA/QC conclusions and decisions, however, has not yet been formalised in a scientific manner. The current, prevailing approach and its limitations are reviewed and a new method is proposed as a substitute tool. This new tool should allow for operational error detection on a batch per batch basis (ie batch rejection) as well as laboratory performance assessment with time on reproducibility.

Jan 1, 2008