Search Documents

By Kajioka H, Nakamura Y

Na2CO3 is a powerful flux for both dephosphorization and desulphurization in oxidizing atmospheres. In order to study refining with Na2CO3 and the nature of the Na2CO3 slag itself, hot metal (4Kg) was melted in Al203 crucibles in a high frequency induction furnace and oxidised with oxygen under Na2CO3 slag. The behaviour of Na2CO3 at high temperature was observed by thermobalance. It was found that dephosphorization ceases in a few minutes and [,P] after refining is easily lowered to less than 0.010%. [%P] after refining is affected by [Si], [P] of hot metal, the refining temperature and the consumption of Na2CO3. Desulphurization also ceases in a few minutes but it shows curious behaviour, increase of [S], decrease of (S) and increase in sulphur lost, during the latter half of run. [%S] after refining is also affected by [P] of hot metal, the refining temperature and the consumption of Na2C03o

Jan 1, 1980

By H Lehtonen, H Mansikkaviita

In primary copper smelters, the received copper concentrate and other materials contain a certain amount of moisture, ranging from six to 14 per cent. Moisture in wet concentrate has a negative effect on the performance of the smelting furnaces when it is fed directly to the furnaces, namely increasing the energy consumption and the off-gas flow. There are several drying technologies available for drying copper concentrate, varying from direct heated rotary dryers and flash dryers to indirect heated steam dryers. Application of steam dryers has changed the drying process for copper smelters. Produced from a waste heat boiler, steam as heating medium enables plant-wide heat utilisation. Fossil fuel used from outside sources to remove water is no longer required and the combustion chamber is not required. In addition special attention has been paid to overcome the known problems of pollution emissions, excessive wear, clogging and frequent maintenance. The Kumera steam dryer is featured with many advantages based on principal improvements in reducing tube element wear and increasing drying efficiency. Thus, it has been considered as the first choice for those smelters where steam is available.

Jan 1, 2006

In presenting size analysis data, one has the choice of various graphical techniques; each no doubt has been developed to highlight a particular aspect of the data. A frequency size distribution plot is used quite extensively to illustrate the importance of the finer size particles in iron ore granulation. However, the basis for such a plot is often not appreciated. As a result, cases of incorrect use can be cited. The aim of this paper is to extend the work of Alien (1981) and to provide, using examples and figures, a basic understanding of the implications of the various size distributions. A simplified method of presenting sizing data on a linear scale graph paper is presented and recommended. This involves a simple construction of a histogram of mass fraction versus particle size (in geometric progression).

Jan 1, 1992

By Spencer P. A

Bacterial oxidation, previously known as bacterial leaching or bio-leaching, has been applied at laboratory and pilot plant scale to many refractory ores and concentrates around the world. The most common bacterial culture used in this process has been Thiobacillus sp. This organism is limited in commercial application, especially in Australia for several reasons. The optimum operating temperature range for this culture is 30¦C to 40¦C and high levels of some metals such as arsenic, silver, and copper have toxic effects on the culture thus reducing its effectiveness. The culture employed by BacTech (Australia) Pty lid is a moderately thermophilic culture which operates in a temperature range of 40¦C to 55¦C (which is more amenable to the Australian climate) and with higher resistance levels to metals often found to be toxic to Thiobacillus sp..

Jan 1, 1991

Industry has a very special request to make. Environmental issues must not be allowed to become a factor of competition so that nations or individual industries can gain economic advantages for themselves by encroaching unduly upon the environment. An international harmonisation of the demands imposed on specific industries and industrial plants where discharges are concerned is therefore essential. The same applies to any to any action contemplated against noxious products. An important step towards that goal is no doubt represented by the United Nations Conference on the Environment scheduled for 1972. Conclusions: Australia must recognise its responsibilities in an inter- national movement to control pollution. It must react on a national scale to a problem which is threatening our whole national environment. To gather, collate and coordinate the information needed to ensure policies which strike a balance between conservation and development, we must look towards the Commonwealth to coordinate the activities of its own instrumentalities and those State and independent bodies working in the area. Financial aid must be provided to stimulate research and later to ensure that environmental protection policies are observed. These policies will be founded on social economic theories which will be both practical and sound, The United Nations conference on the Environment is scheduled for 1972 and in this is the opportunity for international cooperation. Cooperation in the field of controlling legislation and the collection of much needed data. There is an imperative need to assemble facts for world use - an international know-how bank which acquires the most sophisticated technology of process design and waste purification. Arising out of this Conference, is it too much to expect that there could be established an international authority for environmental control, whose activities are governed on a multi-national basis? Such an organisation would have as its primary concern the collection and classification of official regulations, as well as the sheer collation of data to permit economic evaluation of the costs of conservation of the environment. There is an international scope with different factors involved, including industrial technology: in other words, the concrete measures taken against industrial pollutants ought to be more or less identical for similar industries irrespectives of the countries in which they operate. The assembling of an international common foundation of knowledge is imperative so as to acquire the most sophisticated technology of process design and waste purification available for all who are interested.

Jan 1, 1971

By P D. Williams

The Phoenix mine is one of NewmontÆs open-pit operations located in Nevada. Mining started in 2005, with the mine producing gold, copper and silver. The mine life is about 20 years. The gold grade estimation uses the Newmont in-house indicator kriging approach to handle the high variability in drill hole composite grades and support mining selectivity. Each block contains up to 200 subblocks with different gold grades. A flotation mill is designed to process oxide and sulfide ores, recovering gold, copper, and silver. An additional copper leach process is currently under study to process low gold and high copper oxide material with low copper recovery in the mill. The metallurgical recoveries and processing costs are dependent on many variables including rock formation, metallurgical domain, cyanide soluble copper and sulfide contents. This paper describes the Newmont in-house indicator kriging procedures and the revenue based mine planning software system implemented at Phoenix mine to address the complexity resulting from multi-process, multi-metal and indicator kriging model.

Jan 1, 2007

By R Lau

In recently completed road tunnel projects in Queensland, such as the Airport Link and the Clem7 tunnels, there is a smoke duct running along the roof of the carriageways to extract smoke in case of fire. In New South Wales, no road tunnels have a smoke duct. In the Melbourne City Link tunnels, there is a small smoke duct running along the roof. All of the tunnels are safe as claimed by the designers and authorities. However, there is significant cost associated with providing a full size smoke duct compared with no smoke duct. This paper is going to present a comparison of the road tunnel safety with a smoke duct and those without one from a risk perspective. It further discusses the cost-effectiveness of such provisions and whether similar levels of safety could be achieved without a smoke duct.CITATION:Lau, R, 2014. Smoke duct or no smoke duct for road tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 83–86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

North Stradbroke Island is a large sand mass offshore from south east Queensland. Dredging for mineral sands commenced there in 1956 and the rehabilitation discussed in this paper was commenced in 1967. The frontal dunes have a long history of instability, with little vegetation prior to mining. Re-establishment of the naturally stable contours is essential, and their rehab- ilitation is described. Vegetated high dunes present different problems requiring attention to regeneration of the native species. Methods developed over the past eight years are proving successful.,

Jan 1, 1976

Although small scale mining is regarded by many as of historical value only, this kind of mining activity is still much more widespread than is usually assumed. It has been estimated that it produces as much as ten per cent of the global mineral output. More significantly this figure is often much higher for many of the developing countries of Africa, Asia and South America, signifying the relatively greater contribution of small scale mining to the economies of those countries. It is also noted that small scale mining has always been a feature of mineral production in New Zealand and Australia. An attempt is made to define small scale mining, and the factors determining the suitability of small scale mining operations are discussed. The state of the art in small scale mining is reviewed and the author endeavours to rationalise the important parameters which contribute to successful small scale mining operations and discusses how these parameters may be optimised. The benefits of small scale mining to the mining industry as a whole and to the community at large are outlined. The paper concludes by emphasising the necessity to maintain small scale mining and 'explores' its future 'prospects'.

Jan 1, 1990

In this paper the system of an operative expert estimation of innovative policy of mining enterprise technological development on sustainable development principles, created in the laboratory of economic analysis, planning and management of Mining Institute after D A Kunayev is represented. It is based on application of technology of satellite navigation and global positioning system (GPS). It allows to estimate the geotechnological complex functioning efficiency in the automated mode and on the basis of the obtained results to develop a complex of management measures on the competitiveness increase, realised by means of the automated corporative management system of geotechnological complex. The estimation of complex competitiveness is carried out on such basic aspects, as: technical, technological, organisational, ecological and economic as all of it give certain expenses and influence on complex overall performance. The major difference of the given approach is its realisation within the limits of the automated corporative management system of geotechnological complexes. It is based the fact that data of monitoring of complex's work will provide a sustainable development of geotechnological complex of mining enterprise.

Dec 6, 2010

Legislation, if it is to be effective, must be enforceable by the state and acceptable to the industry. In the mining industry the relationship between the government inspector on the one hand and the mine management and employees on the other, must be one of full co-operation before the system can be effective. To understand our present system, which is-duplicated in most countries of the world, an examination of the history from which it evolved is necessary.

Jan 1, 1975

Silver-lead ores are widely distributed through- out the Mount Lofty and Flinders Ranges, but none of the deposits is large. Historically the Glen Osmond Mines are the most significant as the site of the first metalliferous mining in Australia, but Talisker was one of the three largest producers of silver-lead in a state whose mining history is dom- inated by copper. The mine is located in a magnificent natural setting on Talisker Conservation Park, near Cape Jervis, southwest of Adelaide (Figure 1). It is exempt from the operations of the Mining Act and listed on the Register of State Heritage Items. The mine and associated township of Silverton were dominated by Cornish influences during the period of principal activity between 1862 and 1872. Silverton, located on a ridge overlooking the mine, grew to a population of about 300 at its peak in 1870 and the area was very much another 'little Cornwall'.

Jan 1, 1987

By V Sahajwalla, S Shin

Research activities to classify the quality of iron oxides have a long history but most of such activities are for the existing processes such as blast furnace or DR plant. Therefore the newly developed process, such as the COREX process, needs new standardisation although some basic functions of the new process have similarity to the existing processes. Many researchers (Hauk, 1990; Cho et al, 1998) in the field of COREX process have conducted investigations since the early stages of the process development and activities are underway for further plant optimisation. As Agrawal and Oshnock (1995) pointed out, because coke is not included in the COREX reduction shaft the strength requirement of the feed materials in COREX process will be more demanding than that in the blast furnace. This condition is similar to Midrex DR plant but the main reduction gas of COREX plant is carbon monoxide generated from coal combustion while that of Midrex DR plant is hydrogen from natural gas.

Jan 1, 2000

By Ostrea AM

Aqueous oxidation in an autoclave at ele- vated temperatures and oxygen partial pres- sures is applied to Philippine gold-bearing sulfide ores and concentrates which respond poorly to conventional cyanidation. The gold concentrates are recovered from ores and tail- ings material using the patented OMLI Process (the OMLI Process is able to upgrade tailings material analyzing 0.50 g/t Au to a concen- trate with a grade of 5 g/t Au or better). The results show that with aqueous pre- oxidation of the concentrates ahead of cyani- dation a four-fold increase in gold recovery is obtained compared with straight cyanida- tion. The observed differences in response to the pre-treatment step between various mate- rials are correlated with their mineralogical composition. The chemistry of aqueous oxida- tion is also presented.

Jan 1, 1986

By C J. Stanley

Reflected light optical microscopy, or epimicroscopy, is one of the oldest techniques of modern mineralogy. At a relatively low capital cost, it is also very resourceful, and the analytical choice for the identification of most ore minerals. In ore mineralogy, reflected light optical images have the potential to overcome the main limitation of backscattered electron images from scanning electron microscopes, namely contrast of mean atomic number  below the spectral resolution of the backscattered electrons detector. This is the case for relevant ores, like iron (haematite-magnetite) and copper-zinc ores (sphalerite-bornite), but for both cases the pairs of minerals are easily discriminated in reflected light. The improvements in optics and electronics also made microscopy a powerful source of digital images, suitable for automated analysis for minerals processing, as the determination of liberation spectra. The drawback, however, has always been the impossibility to recognise the transparent minerals, which account for most of the gangue phases in ores, from the embedding resin, usually epoxy. In order to determine if there was any possibility to separate quartz from epoxy resins, reflectance spectra have been acquired for quartz and some commercial epoxy resins (Araldite, BuehlerÆs Epothin and Epocolor, Araldite spiked with fluorochrome from Struers), from 380 to 720 nm in 5 nm intervals. Reflectance of quartz and epoxy is very similar over the whole visible light range, and varies from 4.5 to five per cent. Epocolor, a red-dyed epoxy, reflects slightly more above 560 nm, as does Araldite spiked with the fluorochrome from 460 to 570, but for both the reflectance is still very close to that of quartz, under 5.1 per cent. This data set is final, and precludes the application of reflectance in light optical image analysis for assessment of liberation, phase quantification, or any other signal that requires separation of resin from transparent minerals.

Jan 1, 2008

The flolation behaviour of some Australian uranium ores was investigated. Although uraninite and pitchblend float readily with fatty acids, selective concentration to produce an economically discardable tailing has not yet been achieved. This is attributed to the presence in the ores of a quantity of uranium mineral in finely dispersed form which is very difficult to liberate. For some of the ores, at least, the proportion of this material decreases with increase in head assay.Flotation may be a useful concentrating method for some Australian ores if uranium oxide is to be sold in a free competitive market.

Jan 1, 1967

By Tapponnier P

In North Vietnam, large ductile shear zones are observed along the Red river fault and the Dienbien fault. Left-lateral sense of the Red river shear zone is related to the direction of shortening E-W. NE dipping foliation planes is subvertical. Stretching lineation is subhorizontal ( 25¦). Left-lateral slip observed in the Oligocene Yansun granites demonstrates the major tectonic phase in Neogene, The stress field established from microfaults observed in triassic limestones, Oligocene granites and Neogene Conglomerates. Measurements of striations on fault mirors are used for calculating the stress tensor and for separating tectonic phases. Two tectonic phases in tertiary are separated : first tectonic phase related to the compressive direction E-W corresponds to the major tectonic phase represented by NW left-lateral shear zone. Second phase having the compressive direction N-S associated with the right-lateral movement of the Red-river fault zone opening of the Eastern sea and the Red-river and the Red-river delta is associated with the left-lateral movement along the Red-river.

Jan 1, 1990

By A G. Thompson, E Villaescusa, D Howard

The Western Australian School of Mines (WASM) has developed a facility for the static testing of full-scale ground support elements (Morton et al, 2007). The test facility consists of several stiff steel frames used to support the sample and a screw feed jack is used to load the sample. A large-scale punch test method has been developed to load various shotcrete configurations. The shotcrete is sprayed on to a rock substrate containing a centrally located circular disc. The rock and shotcrete sample is placed on to the sample frame and restrained on all sides. The circular disc is displaced at a constant rate by the screw feed jack which in turn loads the sample. Instrumentation measures the displacement and the load being applied to the sample through the loading disc. The testing method is described in detail and the results from the testing program are presented. The results show that it is possible through laboratory testing to simulate some of the mechanisms of shotcrete support reactions better than conventional beam and panel tests.

Jan 1, 2008

JUDGING from the attitude of past and present Parliaments in Australia, it is a' reasonable assumption that encouragement of the principal industries has been adopted as a main principle in the government of the country, but while in most cases bonuses, subsidies, and other means have been proved successful and become recognized as established methods in the case of mining, which is undoubtedly one of the most important industries, the question is complicated by difference of conditions and variable quantities, and it can scarcely be said that any system has been proved generally successful. Indeed, it would not be a very extravagant statement to assert that problems connected with affording direct monetary assistance in aid of mining development, and at the same time devising a system adaptable to the varying conditions to be met, are, in every State of the Oommonwealth, matters continually exercising the minds of those concerned in providing and ailocating such assistance ie Parliament on the one hand, and the Department of Mines on the other.True, there are methods in vogue of granting State assistance to the mining industry which have undoubtedly been successful, but it is in most cases questionable whether the beneficial results following successful expenditure in one direction have compensated.

Jan 1, 1911

The purpose of this paper is to provide a ælook behindÆ the Coal Mine Health and Safety Act 2002. The more important policy considerations in the development of the Act are described along with a summary of the main provisions of the Act. The Act, together with supporting regulations and other instruments will formalise the use of risk management as a necessary discipline in the systematic management of occupational health and safety. It must be recognised that the purpose of this paper is not to provide a legal interpretation of the legislation nor is it to provide legal advice. Rather, the main purpose is to provide some indication of the underlying intent behind the Act.

Jan 1, 2003