Search Documents

By Borsaru M, Wylie AW

A neutron irradiation technique has been developed which is suitable for the determinat- ion of the iron and aluminium content of iron ore fines (-6 mm particle size) on a moving rubber conveyor belt. The determination of iron entails measure- ment with a NaI(Tl) gamma ray detector of the characteristic prompt gamma rays (7.64 MeV) due to thermal neutron capture in iron, while the determination of aluminium is based on thermal neutron activation analysis. For the latter a second detector must be placed down- stream to monitor the 1.78 MeV gamma radiation emitted after activation of aluminium. Although conveyor speed has no effect on the Fe measurement, it has an adverse influence on the aluminium signal, and the belt speed should not exceed 0.1 m/s if good accuracy is required. Static trials on a 460 mm rubber conveyor belt with constant ore geometry indicate that for iron an accuracy of ¦ 1.2% Fe (2a) can be achieved for crushed run-of-mine ore at

Jan 1, 1978

The Charters Towers 1:250 000 Gravity Data Set represents a new initiative of the Department of Resource Industries (DRI, formerly Queensland Department of Mines) to provide high quality regional gravity data over areas of the State that have high potential for new mineral discoveries. The Department has adopted a strategy to upgrade geophysical data to complement the ongoing Regional Geological Mapping Program (RGMP) of this Department and in areas where the data would be of most benefit to the mineral exploration industry. Part of this strategy is to ensure that these data are released within 6 months of data collection.The 1989 Charters Towers survey was completed as a joint project with the Bureau of Mineral Resources, Geology and Geophysics (BMR), and is the first regional geophysical data acquisition project undertaken by the DRI. Prior to this survey, the only gravity data in this area dates from the B MR regional surveys carried out between 1960 and 1967.

Jan 1, 1990

By Rao S. B, Baafi E. Y

A venturi based multi-scrubber air cleaning system has been developed for dust control along a longwall face in coal mines. The system consists of a number of scrubbers. strategically placed along the wall face which deliver cleaned air at high exhaust velocity into the middle section of the longwall cross-section thus dividing it into two zones. The aim is to maintain the walkway on the powered support side as a zone of relatively clean air. Laboratory studies have shown that the scrubber's average efficiency is 90 per cent. Field trials in three longwall faces have shown that. under normal operating conditions. 40 to 50 per cent average protection efficiency can be achieved within 3 m to 4 m downstream of the scrubber. A three-dimensional finite element computational fluid dynamic model. FIDAP. was used to simulate the airflow patterns the dust concentration and the scrubber dust control technique at a typical longwall face. Results of simulations tally very well with the field results.

Jan 1, 1995

There has been considerable attention in the literature to coarse sizing by wet and dry screening, but these methods have not proven to be applicable to the calculation of screen capacities for fine wet sizing, desliming and media recovery: A method is presented for the calculation of the size of screens for such duties, being based on the mean particle size of the oversize material on the screen which reflects the surface area from which the fines or media must be removed. Similarly for dewatering, it is the area from which the water must be drained. Desliming, media recovery and dewatering are each considered along with water require- ments both with the feed and as wash water.

Jan 1, 1984

By R Stefansen

Stockyard operations are governed by the interaction between the different disciplines required to successfully schedule and control the supply chain of raw material through the stockyard in combination with the effectivity of the operation of the stockyard equipment. The system demonstrates a proven technology for implementing a centralised operation of full unmanned stockyard equipment, using a high precision absolute positioning system based on a Real-Time Kinematic (RTK) Global Navigation Satellite System (GNSS) receivers in combination with 3D rangefinders. The system implementation maps the surface profile of the stockyard inventory and allows in combination with proprietary algorithms for full operation of the stockyard machines without on-board operators. The operational impact of delayering the process by moving to a centralised operation is examined, together with the combined effect on the overall safety in the stockyard as a result of a change in reliance on operator skill dependencies. Average performance gains range from 10–20 per cent. The performance of the automation system is related to a consistency and reliability of uniform operation, which has an impact on the life expectancy and the effectiveness of the equipment. The effects of having instantaneous and correct information about the stockyard inventory volume measurement are investigated in relation towards spot price trading in current fast reacting markets.CITATION:Stefansen, R, 2017. Advanced automation for centralised stockyard operations, in Proceedings Iron Ore 2017, pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal.

Jan 1, 1989

By G Brewster

The Eagle on the Hill tunnels form part of an upgrade of Mt Barker Road, 15 km to the southeast of Adelaide. The upgrade significantly improves safety and reduces delays on this major road, which winds steeply through mountainous terrain. The twin tunnels each spanning 15 metres run in parallel for a length of 480 metres. The tunnels are excavated in slightly weathered high strength slates and very high strength quartzites of the Saddleworth Formation on the western margin of the Mount Lofty Ranges. Steeply dipping slate cleavages and the high fracture ratio result in many slope stability problems in the project area. The level of geotechnical investigation undertaken prior to the calling of tenders for the project was extensive. This included the excavation of a pilot tunnel along one of the tunnel alignments, which allowed accurate mapping and rating of the rock, resulting in an increased level of confidence during the tender process. One of the features of the winning alternative tender design was the use of canopy tubes, flexible steel ribs and shotcrete to replace up to 40 metres of deep portal cuts in unstable rock with driven tunnels. Slope stability issues were overcome with the use of rock dowels and shotcrete. The support concept allowed the safe driving of the tunnel portals with as little as two metres of overburden. The design incorporated lining drainage and criteria for fireproofing based on European experience to ensure the ability of the tunnels to remain stable in the case of a severe fire incident. The support design allowed for maximum flexibility with a range of support types able to deal with the varying ground conditions. Design development and support refinement continued throughout the tunnel construction phase with close liaison between the designer and the constructor. Monitoring and review of feedback from the construction site by the Sydney based design team was easily achieved by means of electronic transfer of photographic and survey information, telephone and fax communication and regular site visits. The contractor for this project is Macmahon Concrete Constructions Joint Venture (MCCJV) and the designer is Connell Wagner. Excavation commenced in January 1998 with tunnel breakthrough having been achieved in early-August 1998 and mid-September 1998 respectively. Concrete lining construction is scheduled for completion in April 1999.

Jan 1, 1999

Delivery of effective plant shutdowns is primary to the business success of mining and processing plant operations. This paper sets out a methodology that starts with understanding the business objectives of the shutdown and promotes rigorous detailed planning, effective communication, appropriate governance and effective participation of plant operations personnel. The result is delivery of business effective outcomes.

Jan 1, 2004

By J Koppe, J F. Costa

A fundamental error of sampling occurs when a sample is extracted from a larger mass of ore or lot. The act of sampling requires that all particles belonging to the lot have an equal chance of being extracted. This type of sampling is called unbiased sampling. The sampling equipment (herein referred to as the sampler) should be constructed with some additional mechanical characteristics to guarantee that the samples will be unbiased. Samplers, extracting increments from a continuous flow, such as a conveyor belt, collect aliquots at regular time intervals. These time intervals relate to the number of aliquots extracted from a given mass of lot, whilst passing through the continuous flow. The frequency of extractions will influence the precision or the error of the sample (integration error). Further, the ore variability influences the amount collected from the continuous flow. Normally, the sampling protocol utilised is designed for the extractions obtained from the conveyor belt, omitting any error committed during this operation, ie the error of extracting from the continuous flow. This study aims to analyse the error of sampling a continuous flow by using a variogram with added on auxiliary functions. Each different piece of material passing through the flow will exhibit a distinct temporal variogram, which should influence the frequency of the samples being extracted for each chosen sampling error. The methodology used is presented in the form of a case study from a coal processing plant.

Jan 1, 2005

By Marquez W

Trace fossils have been found in Bolivian Silurian sediments in "La Iumhre" area close to La Paz-Bolivia.Tracks, are good indicators of depth and environment. A detailed study of the ichnogenus is made.The depth and environmental deposits are analyzed to determine the facies. It was shown that the trace fossils of Silurian sediments in La Paz belong to the Zoophvcos and Nereites facies.

Jan 1, 1990

The paper describes the development leading to the bucket wheel excavator systems now used in the Latrobe Valley and refers in particular to the new S.E.C.V. dredgers Nos. 14 and 15 which will be employed in the Loy Yang open cut. The design concept and operating possibilities of these dredgers are described in detail with reference to the machine characteristics designed for the operating conditions in the Latrobe Valley. The design is compared with units of similar capacity in open cuts of other countries.

Jan 1, 1982

By I Doye

Acid mine drainage is a serious environmental problem caused by the oxidation of sulfide minerals responsible for highly acidic, sulfate and metals-rich drainage. Several methods of mine waste management have been developed that reduce liabilities on environment. Layered co-mingling of waste rock with compacted tailings, covers with capillary barriers effect, and co-disposal of waste rock and tailings are these new methods which are used to reduce the formation of acid mine drainage. These methods shield waste rock dumps from oxygen. These techniques could prevent oxidation reaction. In this study, alkaline industrial wastes are used with acid generating tailings to inhibit acid mine drainage. The alkaline wastes selected are cement kiln dust (CKD) and red mud bauxite (RMB). These alkaline materials are used to keep neutral conditions in the fine material layer and to inhibit the metabolic activity of Thiobacillus ferroxidans which catalyses the oxidation of sulfide minerals. A series of timed static leaching tests were performed by reacting samples of mine tailings with two, five and ten per cent alkaline material in order to characterise geochemical balance between liquid and solid phases. Column tests have been set up with oxidised tailings, waste rock, CKD, and RMB. Column tests have been carried out to simulate layered co-mingling, covers, liners, and co-disposal of waste rock and tailings. Column leach tests were conducted in order to investigate the long-term neutralisation potential of alkaline materials and the drainage water quality. Bacteria counting were performed on each sample after testing. The results obtained show that the addition of alkaline materials permit the retention of near neutral conditions in the fine material layer, thus increasing water quality and preventing bacteria development. In fact, the pH results show that the use of five per cent, ten per cent CKD or ten per cent of a mixture of CKD and RMB permit the retention of neutral pH conditions in the reactive layer. At these percent rates, the concentrations of Al, Fe, Cu, Zn, and SO4 in solution are significantly reduced compared to those obtained with the tailings only. In presence of waste rock, the relative position of the fine material layer is important. When the fine material layer overlaying reactive waste rock is composted of reactive tailings with ten per cent CKD and ten per cent (CKD:RMB), a delay was observed before achievement of near neutral pH. The neutral pH conditions remain stable over time. The mixture of CKD and RMB provides a better short-term neutralisation than the use of CKD alone. The use of alkaline materials is beneficial in order to reduce the concentrations of Fe and other metals such as Cu and Zn as well as the number of viable bacteria. The use of ten per cent RMB alone does not involve the neutralisation of reactive tailings. In the cases where the fine-grained layer are below or mixed with the waste rocks, the near neutral pH values are directly reached with ten per cent CKD. However, the pH values decrease rapidly and the number of viable bacteria increases.

Jan 1, 2003

The recent boom in the mining industry has lead to some unique challenges in successfully operating processing plants. With high turn-over rates of both operators and technical staff, and many experienced personnel leaving regional sites for city based jobs there is often an onsite knowledge vacuum and this in turn puts pressure on both site training departments and senior metallurgists to provide the relevant skills to the continuous stream of new staff. Frequently both operators and new metallurgists are instructed on a æhow-toÆ basis rather than giving them the understanding as to why tasks are performed and decisions are made. This paper has been written with the plant operator and metallurgist in mind and aims to provide suitable material to be incorporated into a site training manual. Topics have been broadly divided into the following categories: factors that operational staff can control; including pulp density, air addition rate, froth depth, particle size and reagent type and use; factors that operational staff cannot control; providing general information on bubble size, froth stability, pulp chemistry and the mechanical effects of the rotor/stator system; and process improvements. Each topic is discussed with a view to clarifying the key process variables that need to be understood and optimised in an industrial operating plant.

Jan 1, 2009

By Yusuf R

Many heap and dump leaching processes involve competitive, complementary and sequential reactions between multiple minerals and reagents. A comprehensive model has been developed to deal with these complex chemical interactions which is based on diffusion control of the reaction rates. All of the mineralogical and chemical data are obtained from representative samples of the ore or the chemical literature. These properties have been incorporated in a general way, making the model applicable to a range of ore-process systems. The simulation is used to predict the absolute reaction rates and can be used before any leach tests are carried out on the ore itself. The applicability of the model and some tests of its validity are presented.

Jan 1, 1984

By Hongzhen Yu, Xiaoping Ma, Jiansheng Qian

The paper introduces the design of an Intelligent Managerial Attendance Machine (IMAM) for coal mines. In the system, data communication is carried by Optical fiber communication, including industrial control computer on the ground and the car

Jan 1, 1998

By Bhattacharyya A. K

A strata parameter is introduced to include the deformation characteristics of the undermined strata in the prediction of subsidence movement. By using the strata parameter and mining factors as parameters, a nomogram for predicting the maximu

Jan 1, 1994

By McQueen LB

The Water Board has been involved in the development and ipgrading of sewerage facilities in the Blue Mountains since 1980. In 1984 the Board prepared a report that dealt with the Blue Mountains Sewage Effluent Management study. Successive 3ovemments have been concerned about development in the 3lue Mountains and the effect this development is having on the luality of the streams flowing into the Blue Mountains National ?ark (presently up for World Heritage Listing).

Jan 1, 1993

By T Hayward, G Lane, M Phillips

In December 2004 Phu Bia Mining Ltd commissioned Ausenco International Limited to conduct a feasibility study for its Phu Kham copper-gold project located in Laos. The feasibility study for a mining and processing operation treating 12 Mtpa of ore averaging 0.56 per cent copper and 0.25 g/t gold to produce an anticipated annual average 200 000 t of concentrate containing 25 per cent copper was completed in early 2006. The plant design incorporates a single processing line and includes a gyratory crusher, overland conveyor, coarse ore stockpile, SAG and ball mill grinding circuit, flotation circuit including regrind and three stages of cleaning, concentrate dewatering and concentrate load-out facilities. The Phu Kham copper-gold mineralisation comprises two principal styles: stockwork-disseminated and banded-massive sulfide within skarn limits. Primary copper in both mineralisation styles occurs as chalcopyrite and secondary copper sulfide minerals. Skarn includes the copper and gold mineralisation contained in pyrite, silicate, magnetite and haematite skarns, and in quartz-pyrite altered sediments. Both the stockwork-disseminated and banded-massive sulfide ores contain relatively high proportions of pyrite relative to the copper and gold mineralisation. Thus, the flotation metallurgy of the Phu Kham orebody is characterised by the need to reject a high proportion of the pyrite during differential flotation to yield a concentrate grade of approximately 25 per cent copper. The rejection of pyrite is accompanied by the rejection of some copper and gold and can result in modest metallurgical recovery. Consequently, the greater the pyrite content, the lower the expected copper and gold recoveries. The relative pyrite content is expressed on the basis of sulfur:copper ratio. For Phu Kham ores, the sulfur:copper ratios are in the range eight to 14 on a blended annual basis, but can be greater than 20 in the skarn components. Higher grades of copper and gold are also present in the skarn mineralisation. The design concepts for the concentrator were influenced by the need to provide a low capital cost approach for the project due to the relatively low grade of the ore and the modest metallurgical recovery. The concepts used to minimise capital cost whilst retaining operating and maintenance flexibility are discussed, together with the metallurgical challenges imposed by the high pyrite mineralisation.

Jan 1, 2007

The moisture content of clean coal contributes significantly to the product's transportation costs, handleability characteristics and/or energy value. A major contributor to the total moisture is the ever increasing proportion of fine coal in

Jan 1, 1994

By D J. Williams, S Islam

Fine-grained coal tailings slurry undergoes only limited settling and self-weight consolidation, and tends to remain slurry-like and unsuitable for conventional laboratory consolidation testing. In addition, constant rate of loading consolidation testing is more representative of the continuous disposal of tailings slurry into a tailings storage facility (TSF) than conventional step loading. The laboratory consolidation testing of coal tailings slurry under a constant rate of loading has been carried out in a purpose-built, large-scale, slurry consolidometer, instrumented with load cells and pore water pressure (PWP) transducers. In the slurry consolidometer, the rate of loading may be varied to represent the actual rate of rise of the tailings in the TSF. A slow rate of loading increases the test duration, while too fast a rate of loading may build up very high excess PWP, without achieving significant consolidation. For the particular fine-grained coal tailings slurry tested, the rate of loading in the slurry consolidometer is varied to access its effect on the development and dissipation of excess PWP. The resulting consolidation parameters are evaluated and explained using the recorded settlement and PWP data.CITATION:Islam, S and Williams, D J, 2018. Optimisation of constant rate of loading slurry consolidometer testing of fine-grained coal tailings, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 72–80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018