Search Documents

By R. W. Thompkins

MINE operators are concerned with temperature conditions in their mines, particularly the effects of high temperatures on the l1ealth and efficiency of tl1eir employees. This paper is written to focus attention on the variables of heat transfer between rock and air. It illustrates the difficulties of predicting the manner, and the extent, of heat transfer from theoretical concepts, prior to actual operation of a mine airway. There are ~1any sources of heat in mines. The most important is that of the rock surrounding the airway. This heat, in turn, is a product of the age of the rock, faulting, proximity to recent igneous activity, oxidation of sulphides, hot ground waters, etc. The sources of heat may be constant for any one mine, but they are far from constant when dealing with various mining districts or e1•en with a number of mines in the same district. A second source of heat is that produced by machinery in operation. Practically all the waste

Jan 1, 1962

By G. De Gregoriis, G. E. da Mota, H. P. Dias, J. E. M. Blasques

In recent years, like many other smelters around the world, Albras has been increasing line current. The necessary adjustments to the work practices and process variables need to be made on all potlines, which in this case means on 960 cells at the same time. It was a challenging task to adjust the process parameters to the new amperage. In July 2003 potlines 2, 3 and 4 were running at 1 73 kA and the goal at that time was to reach 180 kA. Preliminary trials with 180 kA were performed on a group of 10 boosted cells on potline 3 in order to investigate possible operational problems. It was decided to increase the amperage in three steps accompanied by continual evaluation of the state of the process. In July 2004 the target of 180 kA was achieved with good operational results. This paper presents the overall results, the parameter adjustments made during the amperage increase in the booster group and how the increase was implemented on the other potlines.

Jan 1, 2006

By Mi, Dong Liang, Jingyuan Bai, Victor Zhou, Xujun

Squirrel cage induction motors are the mostly used motors at present. Currently, the rotors of the squirrel cage induction motors are produced by aluminum die casting technique with the advantages of low cost of rotors. It is well known that the copper’s electrical conductivity is around 40% higher than that of aluminum. If copper is used to replace the current widely used aluminum in rotors, the total loss of motors will be reduced, hence increasing the overall motor efficiency. Copper rotors can be used to produce high efficiency and even super premium efficiency motors without enlarge the motor frame size. Considering the huge quantity of motors, the die casting process is the best solution to produce copper rotor with economic cost. Because of the characteristics of copper, it is difficult to produce copper rotors by casting similar to that done in aluminum rotors. In order to improve the die casting quality of copper rotor, a new tooling structure was developed and the casting process of copper rotor was simulated and analyzed by Any-casting software. The filling process, solidification process, inner gas distribution and residual melt modulus were analyzed. It was found that the design of symmetrical runner and inner runner on both sides was helpful to reduce the impact of molten copper to the cavity surface during the filling process. The use of Slag traps array can reduce die casting defects inside the end rings. That will be helpful to improve the rotor quality. INTRODUCTION Squirrel-cage AC induction motors are most widely used in the world. In 2017, the total installed capacity of AC motors in China has reached more than 1.2 billion kW, and the annual power consumption accounts for about 60% of the total national electricity consumption. To improve the efficiency of squirrel-cage motor will be helpful to energy conservation and environment protection. There are several ways to improve efficiency of induction motors, using copper rotor is one of the most effective solutions. It is well known that the copper’s electrical conductivity is around 40% higher than that of aluminum. If copper is used to replace the current widely used aluminum in rotors, the total loss of motors will be reduced, hence increasing the overall motor efficiency. Copper rotors can be used to produce high efficiency and even super premium efficiency motors without enlarge the motor frame size.

Jan 1, 2019

By M. A. Roche

The property of the Hudson Bay Mining & Smelting Company, Limited is located at Flin Flon lake, 85 miles northwest of The Pas, Manitoba, on the Manitoba-Saskatchewan boundary. The area is at latitude North 54°, and is approximately 1,000 feet above sea level. The ore-body occurs in amygdaloidal greenstones, which are to be referred to the earliest basic volcanic flows in the district. It was discovered in an outcrop on a point of land jutting into Flin Flon lake, and subsequent diamond drilling proved that it extends under the lake both to the north and south of the point of discovery. After the taking of soundings from the ice during the winter months, it was estimated that l,000,000 tons of overburden, mainly mud and clay, would have to be removed to expose the underlying ore. Flat diamond-drill holes indicated that the ore-body was separated into more or less independent lenses by horses of unmineralized greenstone, and that in places the overall width, including horses of waste, reached 450 feet. These several] conditions were the main factors influencing the management in their decision to adopt an open-cut method for the mining of the upper portion of the ore-body. Before it was possible to commence stripping operations, it was necessary to dam-off the eastern portion of Flin Flon lake, instal pumps, and de-water the dammed-off area. Dams for this purpose were constructed of mine waste rock and clay filler from nearby hillsides. Material for the bottoms of the dams was taken across Flin Flon lake in hopper-bottom barges. Trestles were then built on the dam bottoms and dams were complete by the time trackage was available. De-watering commenced in April, 1930, and was completed by the latter part of May of the same year. Estimated pump output for the period was roughly four billion gallons. Two Morris 10-inch dredging pumps were used, direct-connected to 250 h.p. electric motors. Individual pump capacity was rated at 3,000 g.p.m. against a 150-foot head. Average head for the operation was 50 feet, which increased the total output considerably. The pumps were mounted on floating barges in cribbings of piling driven at the lowest points in the lake bottom.

Jan 1, 1933

By J. R. Goode

ABSTRACT Aurora Energy Ltd. is considering a 10,000 t/d process plant to produce 97 million lb (43,998,460 kg) of U3O8 over a 17-year project from uranium deposits in coastal Labrador. This paper summarizes the test work, mostly done by SGS Mineral Services in Lakefield, Ontario, and the economic studies supporting flowsheet selection. The proposed flowsheet includes semi-autogenous grinding (SAG) and ball milling, acid leaching using air/SO2 as an oxidant, and resin-in-pulp (RIP) extraction of uranium from the leached slurry. Other unit operations examined include ore sorting, heap leaching, liquid- solid separation, solvent extraction, and nanofiltration for eluate upgrading. We also review the extensive environmental test work and studies that were completed.

Jan 1, 2012

By D. E. Deegan, G. Holcroft, T. P. Johnson

"The rising cost of extracting metals from existing traditional deposits, increasingly stringent environmental regulations and a greater awareness of corporate social responsibility issues are all factors in stimulating the examination of mine tailings and small-scale alluvial deposits as a potential source of new raw materials. Furthermore, despite tougher economic times the demand for commodities remains strong, in no small part as a result of the growth of the world’s emerging economies.This combination of social and economic factors looks set to continue in the long term which will encourage greater recovery of materials from previously ignored sources such as mine tailings and ores from alluvial deposits.An expansion in the recovery of useful materials from mining-related activities is likely to require the use of robust and innovative techniques that have a built-in degree of future-proofing; DC plasma technology is one such technology.As a result of its ability to separate the valuable metal and minerals from the waste material while destroying hazardous compounds, Tetronics’ DC arc technology offers an alternative approach to resource recovery from a wide range of mine ores. Harmful cyanide compounds and the vast quantities of water used in conventional hydrometallurgical processing are avoided when plasma processing is adopted. DC arc technology also brings additional benefits, including: the extremely effective destruction of organic materials, the conversion of the inorganic material into a re-useable aggregate and the high tolerance of the process to fine and dusty materials. This paper presents details of Tetronics’ DC arc technology as one of the key pyro-metallurgical solutions available for the recovery of valuable materials from traditional mine ores and tailings, as well as giving specific examples of how the technology has been successfully employed in the recovery of enriched slags, ferroalloys and other metals."

Jan 1, 2016

By S. Esfahani, M. Barati

Heat recovery from blast furnace slags is often contradicted by another requirement, to generate amorphous slag for its use in cement production. As both the rate and extent of heat recovery and slag structure are determined by its cooling rate, a relation between the crystallization kinetics and the cooling conditions is highly desired. In this study, slags with different basicities were studied during non-isothermal cooling. Their continuous cooling transformation (CCT) diagram were plotted and compared with each other. Then, a mathematical model was developed that predicts the amount of crystallization during cooling. The results were validated by experiments performed by Single Hot Thermocouple Technique and image analysis. A second mathematical model that calculates temperature history of slag during its cooling was coupled with the above model, to allow optimizing the slag/air ratio for both heat recovery and slag glass content.

Jan 1, 2015

By J. Lu, D. G. Ivey, H. Henein

Microalloyed steels are widely used in the oil and gas industry. They are a class of high strength, low carbon steels containing small additions of niobium (Nb), titanium (Ti), molybdenum (Mo) and/or vanadium (V). These steels have good strength, toughness and excellent weldability, which are attributed in part to the presence of nano-sized carbides, nitrides and carbonitrides. In the pursuit of developing higher strength microalloyed steels, it is of great interest to quantify the size, distribution, volume fraction and chemical speciation of these precipitates. However, characterization techniques suitable for quantifying fine precipitates are limited. Possible characterization techniques include SEM, TEM and matrix dissolution. A comparison is presented of the various techniques.

Jan 1, 2005

By P. Kobylin, K. Haavanlammi, K. Valkama

"Base metals and precious metals can be recovered from a nickel matte or nickel concentrate using the Outotec nickel chloride leaching process. The raw material is leached with hydrochloric acid and the metals are recovered by solvent extraction, where ammonia is used to control the pH. Ammonium chloride is regenerated to ammonia and the side product of this step is calcium chloride solution. The regeneration utilizes either calcium oxide or calcium hydroxide. The calcium chloride solution is used to convert sulfuric acid into a hydrochloric acid solution while producing pure gypsum as a side product. The regeneration and reuse of ammonia and hydrochloric acid in this process will have a positive impact, from the point of view of both operating costs and environmental sustainability. This paper concentrates on the test work and technical concept development performed by Outotec to implement and develop chemical regeneration and recycling into a vital part of the nickel chloride leaching process.INTRODUCTION According to a nickel market analysis, the nickel market is expected to grow in the future. Main driver for this growth is the increase in stainless steel consumption as the living standards are equalizing globally. The expected increase in the amount of electrical cars and the need for nickel in the batteries of electrical cars also gives potential for the increased need for nickel in near future. At the moment the use of nickel in nickel-cobalt-manganese (NCM) and nickel-cobalt-aluminium (NCA) Li-ion batteries is in the range of 14 ktpa. It is estimated to increase to the level of 90 ktpa by 2025. In every era of the nickel industry, Outotec has been constantly developing new processes to create environmentally sustainable and economically viable processing routes. The Outotec® Nickel Matte Chloride Leaching process is a great example of a process that is flexible regarding raw material and could also treat nickel raw materials that are difficult for smelters. Outotec’s main options for pyrometallurgical nickel treatment include the Outotec® Direct Nickel Flash Smelting process (DON) and the Outotec® Ausmelt TSL process. The DON process is operated in Boliden Harjavalta Nickel Smelter in Finland. Ausmelt process is in use for example in Daye nonferrous plant in China. In the Outotec® Direct Nickel Flash Smelting Process, a sulphide nickel concentrate is processed in an Outotec Flash Smelting Furnace (FSF). Producing concentrates and processing them by Outotec Direct Nickel Flash Smelting to matte followed by hydrometallurgical refining offers a reliable route from concentrate to product. In the DON process, high-grade matte with low Fe content is produced in the FSF and the valuable metals in the slag are recovered in an electric furnace (EF). The Outotec® Ausmelt TSL process can use a large variety of raw materials (concentrates, secondary material and scrap metal) as feed. Fuel and oxygen are injected into the furnace through TSL (Top Submerged Lance) and this enables efficient smelting. Both Flash Smelting and TSL plants produce nickel mattes, which can be refined with Outotec hydrometallurgical processes."

Jan 1, 2017

By F. Y. Grepe

"THE MOST common type of mine hoist is, as is very well known, that in which the a.c. wound rotor motor is the driving medium. The reasons for the use of the wound rotor motor are, of course, economic. This type of equipment has, during the years, proved to be very reliable and reasonably satisfactory. It is, in fact, still being installed and in some places where a very hard and exacting duty cycle is demanded. As an example, a 600 h.p. 2,300-volt job was recently installed at the Caledonia mine (1) at Glace Bay. This is a vertical. hoist in a shaft only 175 feet deep but it is, nevertheless, working hard bringing coal to the surface and in making a trip at a speed somewhat better than every 20 seconds.The control equipment for such installations usually consists of a pair of primary reversing contactors which are interlocked both mechanically and electrically, together with some form of secondary controller. This, in the case of small hoists, can be a drum controller and metallic resistors or, in the case of larger hoists, a magnetic contactor panel and metallic resistors or, alternatively, can be one of the various forms of liquid rheostats which are available. The liquid rheostats, if of the dipper type, may be manually operated or it may be operated by some form of servo motor mechanism. In the weir type of liquid controller, the electrolite is, of course, pumped in and out of the rheostat."

Jan 1, 1954

By J. E. Moyle

The costs of labour and electric power are of prime concern to almost all industrial enterprises, and various methods of reducing their impact on production costs are constantly being developed. Automation is one of these schemes, and has received a good deal of attention in the past few years. In the mining industry, compressed air is almost universally used, and its cost is significant. Although the compressor machinery now in use has achieved a high degree of development, the hazard of explosion and fire still exists in these systems. There is thus considerable resistance in some quarters to suggestions that such installations can be safely and successfully automated. The Milliken power plant consists of two 30,000 lb. /hr. fully equipped high-pressure boilers, four H.P. air compressors, a steam turbine for stand-by power, and several L.P. compressors and vacuum pumps. With the installation of automatic and protective equipment in the machinery section, the shift force has been reduced from three to two men.

Jan 1, 1963

By T. Wajima

"A novel carbonaceous adsorbent for recovery of nickel from nickel plating waste solution was prepared from rice straw using sulfur impregnation. The rice straws were cut to 1 cm pieces, and then immersed in 0.01 - 3 M K2S solution to prepare sulfur-immersed materials. The immersed-materials were heated at 100-700 ºC in nitrogen gas to produce the sulfur-impregnated carbonaceous adsorbent by pyrolysis. The contents of carbon and sulfur in the adsorbent and abilities of adsorbent to recovery nickel from aqueous solution were examined. The contents of carbon and sulfur in sulfur-immersed materials are almost same as those in raw material. In pyrolysis, with increasing the heating temperature to 200 ºC, the contents of carbon and sulfur are almost constant, and then above 300 ºC those increase. The recovery for nickel using raw material, sulfur-immersed material and the product pyrolyzed at 100 - 200 ºC are almost same, and with increasing the heating temperature to 400 ºC, that of the product increases, and above 500 ºC that of the product decreases. In immerse step, with increasing K2S concentration, the carbon content of the product at 400 ºC gradually decreases, the sulfur content of the product increases, and the recovery for nickel using the product gradually increases and then above 1 M K2S decrease. The product prepared from material immersed in 1 M K2S solution at 400 ºC indicates a maximum recovery for nickel ion. The product can adsorb nickel ion in nickel plating waste solution coexisting with phosphate ion, and adsorbed nickel ion in the product was deposited as nickel metal after heating at 1000 ºC under N2 atmosphere.INTRODUCTIONRice is the second world’s largest cereal crop after wheat, but produces large amount of straw residues, of about 330 million metric tonnes. Rice is a widely grown crop in Asia, and rice straw is produced as a by-product of rice production. In most parts of rice fields, open-field burning of rice straw is commonly practiced in the region when there is limited time to prepare a field for the next crop. However, open-field burning of crop residues is an uncontrolled combustion process during which air pollutants are emitted into atmosphere. These air pollutants have significant toxicological properties and are potential carcinogens (Gadede et al., 2009). Although wildfires are prohibited in cultivation fields of most countries, farmers usually keep on burning their crop by-products. Biomass burning is an important source of aerosol particles which may affect local and regional air quality (Gao et al., 2011), and also contribute to global climate changes."

Jan 1, 2016

By R. Carter, C. S. Samis

"SummaryThe results of this investigation indicate that the gold in the cyanide tailing of refractory gold cyanides is occluded in fused •particles formed during roasting. This conclusion was reached following microscopic examination of calcines produced at various furnace temperatures with different atmospheres, and a •comparison with calcines produced by decomposing samples of completely sulphated concentrate under conditions such that the maximum particle temperature varied between 6•50°C. and 1,100°C. This comparison showed that the particle temperature during a normal roast may be several hundred degrees higher than the furnace atmosphere, or that the fusion is associated with a low melting (950°C.) eutectic mixture of FeO and FeS.Because of the unavoidable particle fusion during a furnace roast, and because low particle temperatures are essential for gold extraction by cyanidation, aqueous medium oxidation under high oxygen pressures was studied. Gold recovery from calcines produced by this means was over 98 •per cent •compared with a maximum of 80 per cent from furnace calcines.IntroductionMANY arsenical gold ores are called 'refractory' because much ' of the gold cannot be satisfactorily extracted by cyaniding the raw ore or concentrate. Even when such ores are roasted to oxidize .the iron and arsenic and 'release' the gold, often 10 to 25 per cent of the gold present is lost in the cyanide residues."

Jan 1, 1952

By A. Y. Smith, R. J. Allan, E. H. W. Hornbrook, R. W. Boyle, W. Dyck

"HYDROGEOCHEMICAL METHODS in the Canadian Shield can be based on analyses of the following :(1) spring waters and their precipitates;(2) stream and river waters;(3) lake and muskeg waters;( 4) ground waters from drill holes, wells, faults, etc.;(5) waters issuing from diamond drill holes, faults, shear zones, etc. into mine workings and open pits; also analyses of precipitates associated With these waters.The first four can be utilized in both reconnaissance and detailed surveys. The last is suitable only for detailed work.For hydrogeochemical methods of prospecting to be effective, the following conditions must be present. 1. Natural waters must come into contact with mineral deposits and remain in contact with them long enough for the solution of detectible amounts of ore, gangue or indicator elements. 2. Dispersion patterns must be present in the hydrologic systems in order to trace the elements back to their source. These patterns may take the form of trains (e.g., increasing amounts of elements upstream toward t he source (s), Figure 1 ) or halos (e.g., increasing amounts of elements in bodies of water toward the source (s), F igures 2 and 3)."

Jan 1, 1971

By J. R. Bradfield

THOSE familiar with the development of the Horne mine can readily appreciate that more and more accommodation bas been required for underground labour as the mine has grown. A permanent fire-proof change house, 30ft. by 75 ft., was built in 1927 to accommodate 194 men. This was extended ro 30 ft. by 92 ft. in 1928 to accommodate 296 men, and to 30ft. by 110 ft. in 1930 to accommodate 398 men. By 1933 this building was again overcrowded and tentative plans for a new change house were drawn up. However, it was realized that future operations would be centred around No. 4 shaft and a proposed new shaft, and the decision as to the location of the new change house had to be deferred until the area which seemed most suitable for the new shaft had been thoroughly explored underground. In the spring of 1934, the basic idea was accepted of drying the wet clothes in open mesh compartments or baskets located between rows of standard steel street-clothes lockers and built so that the covers or lids would serve as seats or benches.

Jan 1, 1935

By L. H. Cole

Introduction The increasing importance of the gypsum industry in Canada is evidenced by the fact that the production has increased from 473,129 tons valued at $809,632 in 1909 to 1,205,846 tons valued at $3,622,007 in 1928, an increase of over 155 percent in quantity, and of 347 percent in value, in the 20-year period. Although the export trade in crude gypsum still forms a large proportion of the industry, it is gratifying to see that the home consumption is steadily increasing, and while the percentage of the crude gypsum mined that is manufactured into the calcined products in the country is only 16.8 per cent, its value is practically 50 per cent of the total gypsum production of the whole country. It is to be hoped that each succeeding year will see an increase in the amount manufactured in Canada, and, with the steady growth of the country and a serious endeavour to capture a part at least of the world market in gypsum products, the outlook for the industry is decidedly promising. The value of gypsum as a commercial commodity has been known from the time of the early Egyptians; in fact its value for certain purposes has been known so long chat the date of the discovery of its peculiar properties is unrecorded.

Jan 1, 1930

By Glenn Kosick, Roger Amelunxen, Glenn Dobby

"The variability in flotation response within an orebody is often a significant problem to address during the design phase of a flotation circuit. In addition, for existing operating plants, the reasons for such a variability need to be clearly understood and accounted for if plant performance is to be optimized. MinnovEX Technologies, in collaboration with major mining companies, is developing methodologies and tools to address the issue of variability in ore characteristics (such as ore hardness and flotation response). The tool is used for design and scale-up of flotation circuits from lab flotation data, and for prediction of recovery and final concentrate grades throughout the mine block model for any given circuit design.INTRODUCTIOTNH: EI SSUEB EINGA DDRESSEDThis paper describes the current development of a methodology and software tool for improved flotation plant design and enhanced prediction of froth flotation performance in an operating plant. The need for this tool is attributed to two primary factors: variability of flotation response properties throughout an orebody and related difficulties with scaleup from laboratory tests. Consider these in more detail.It is well recognized that separation performance via froth flotation will vary significantly within a single mineral deposit. This has been enhanced through the wide application of SAG milling. Throughput with SAG mills is more susceptible to ore hardness changes than is the case with crushing-rod-ball circuits; it is not uncommon to see SAG mill throughput to vary by up to 100% on a regular basis, e.g. 1000 tph to 2000 tph.The implication of this on laboratory testing for prediction of metallurgical performance is as follows: it is unlikely that either the plant grind (size distribution) feeding froth flotation or the flotation residence time will be known at the time of laboratory testing for a given block of ore. Hence, the grind used for the laboratory test is not likely to be that which actually occurs once the ore is processed, and the laboratory retention time may not represent the plant conditions."

Jan 1, 2002

By A. M. Glendinning

"IntroductionLocationTHE PROPERTY of Aunor Gold Mines, Limited is in Deloro township, Ontario, about three miles southeast of the town of Timmins. It consists of a group of eleven claims located between those of Buffalo-Ankerite Gold Mines, Limited, and Delnite Gold Mines, Limited.GeologyThe ore zone at the Aunor mine consists of a narrow band of fine grained pillowed andesite, irregular bands of 'brown to green carbonated andesite, and lenticular bodies of quartz feldspar porphyry. The zone strikes N.80°E., dips 60 North, and has been traced for 5,000 feet across the property. It varies in width from 0 to 250 feet and is bounded on the north and south by masses of dark bluish-grey tale chlorite schist. These schist bands have widths up to 500 feet.The ore occurs in a series of parallel and branching veins confined to the limits of the zone. These veins tend to terminate and die out on the footwall schist contact, striking generally parallel with the ore zone. In wide sections of the zone, 150 to 250 feet, the veins range in width up •to 3.5 feet and may occur in two or three horizons across the width of the zone, each mineable independent of the other. They tend to dip a little flatter than the general dip of the zone. Where the zone is narrow, the veins are so closely spaced and numerous they can be mined together and in some places the complete zone has been mined from schist to schist."

Jan 1, 1953

By Michel Épiney, COREM, Mario Drapeau, Caroline Olsen, Claude Bolduc, Benoit Levasseur

"Several metal sulfide minerals (such as copper, zinc and iron), generally abundant in precious metal-containing ores, are known to dissolve during the cyanidation process. These unwanted reactions consume a significant amount of cyanide and oxygen, which is required for the extraction of gold and silver. Leaching kinetics of sulfide minerals are very fast in contact with oxygenated cyanide solutions. Therefore, the solution quickly becomes charged with oxidation products that are mostly metal ions, metallo-cyanide complexes, metal oxides and other sulfur species including thiocyanate, sulfides, polysulfides, thiosulfate, sulfites, sulfates, etc. COREM’s Extractive Metallurgy team has been conducting a research program on the improvement of the gold cyanidation process. As a part of this program, the current study aims to investigate the effect of certain operating parameters on the reactions involved during pre-oxidation and cyanidation. The effect of pre-treatment under ozone was investigated using an industrial pulp recreated from process water (charged with thiocyanates) and homogenized flotation tailings material from Agnico Eagle's LaRonde mine. In terms of mechanisms, the ozone treatment provides a complete deactivation of the material surface (characterized by EDTA extraction) and the solution (characterized by Ionic chromatography). This resulted in a lower reactivity of sulfide minerals that led to substantial gains in terms of consumption of cyanide and thiocyanate formation during the cyanidation process. The ozone-pre-treatment edges the classical pre-oxidation treatment (such as oxygen, hydrogen peroxides, etc) providing a quicker deactivation of the sulfide matrix and higher reagent savings in subsequent cyanidation process.INTRODUCTIONThe presence of sulfur in the process of gold leaching by cyanidation is a major drawback to optimizing the reagents consumption with suitable operating conditions. The coexistence of sulfide mineral species, such as pyrite, chalcopyrite, pyrrhotite or sphalerite along with the gold-bearing ore have, indeed, a negative impact on the extraction of precious metals by cyanidation (Bayat et al., 2003), (Azizi et al., 2010). These minerals are known to dissolve with cyanide under alkaline conditions and release in the slurry different kinds of sulfide by-products like polysulfides, thiosel, sulfite and sulfate (Seal II & Hammarstrom, 2003) (Breuer et al., 2008a), (Marsden & House, 2006) (Ghasemian Langeroudi et al., 2013). Once these sulfide by-products are released in solution they react with cyanide to form thiocyanate (Marsden & House, 2006) (Breuer et al., 2008b). The consequence of the dissolution of these cyanicides, is a significant increase in cyanide consumtpion as well as a slow-down of gold extraction."

Jan 1, 2016

By Lucas G. Thompson

My topic, "The Administration of Mineral Rights'.' is possibly an unusual one, as it deals with a subject upon which many of us have a more than passing interest, I thought ?it might prove consistent with the objects of this meeting, more especially as I propose to deal, not with those broad subjects of nation-wide importance which are often the subject'? of learned (and sometimes futile) academic discussion, but rather with problems in their practical light. To the scientist, the important question is What is it? to the technician, Can it be utilized? to the business-man, Will it pay? All three questions are important, and so quick has been the march of business on the heels of science? that the one question follows the other with astonishing rapidity and all three must be considered in the modern management of a mineral estate. A .good illustration of the force of this can be found in the recent advance of our knowledge of the element helium in which we have advanced from a solution of the first question to the last question in the short period of 55 years. It is to be borne in mind, however, that in the administration of mineral rights, the question "Will it pay?:' is of primary importance. What forms a mineral estate ? A former practice in western Canada in selling lands was to sell the hair with the hide. All transactions sold the lands in fee simple, which included all mines, minerals and rights and privileges whatsoever, excluding only the royal metals, gold and silver, which by imputation, though not by specific reference, in deeds. of title are reserved to the Crown. At that time the country was in the first ?stages of settlement and the value of our mineral resources was hardly appreciated and little understood.

Jan 1, 1923