Search Documents

By M. Rafieazad, P. Fathi, M. Mohammadi, A. M. Nasiri

This study examines the impact of low-temperature heat-treatment cycles on microstructure and corrosion performance of Direct Metal Laser Sintered (DMLS) AlSi10Mg_200C alloy. It is known that the morphology and the size of eutectic silicon are the two most critical factors affecting mechanical properties of the AlSi10Mg alloy. Although high-temperature heat-treatment cycles are common practice for the strengthening of the cast Al-Si-Mg alloys, in the case of DMLS fabricated AlSi10Mg alloy, high-temperature solutionizing and low temperature annealing cycles result in mechanical properties degradation primarily due to a dramatic decrease in the solubility of Si in the super-saturated a-Al matrix of the as-printed alloy. In this study, low-temperature heat-treatment cycles that only promote precipitation of Mg2Si accompanied by the interruption of the silicon network were investigated. SEM and XRD analysis were utilized to observe the evolution of microstructure after different annealing heat-treatments at 200, 250, 300, and 350°C for 3 h. Increasing the heat-treatment temperature contributed to the Si networks interruption and an increased precipitation of Mg2Si phase. Low-temperature annealing from 200 to 350°C was found to promote the homogeneity of the microstructure characterized by a uniform distribution of eutectic Si in ??-Al matrix. Additionally, in order to investigate the impact of different heat-treatment cycles on corrosion resistivity of DMLS-AlSi10Mg_200C, the potentiodynamic polarization testing and electrochemical impedance spectroscopy were performed in a 3.5 wt.% NaCl solution. The results revealed more uniformly distributed pitting attack on the corroded surface by further increase in the annealing temperature, which was attributed to the uniformity of Si dispersion. In comparison, low temperature annealing at 200°C led to a penetrating selective corrosion attack along the melt pool boundaries, resulting in a higher corrosion rate associated with the lower absolute value of impedance of the protective passive film on the surface.

Jan 1, 2018

By R. D. Hossack

"The selection of a site for plant facilities is a function of several factors and has as its objective the maximization of profits, given fixed markets and sources of raw material locations. In practice there are several sites, any one of which or a combination of two or more would be suitable to meet the basic requirements of source of supply of raw material and labour and still fulfill market demands. The model used to select the optimum profit combination utilizes both computer programs and traditional financial analysis techniques. Of the three computer programs used in the mode), one is a linear program and another is a transportation simulator. Basic cost and price data are required. In examining costs, three levels are used: (a) distribution costs of raw material to the plant and finished goods to the market; (b) direct production costs at the plant, such as labour and locally supplied material; and (c) capital and overhead costs at the plant, such as construction costs, taxes, insurance, and federal and provincial cost allowances. The direct costs generally depend on the scale of operations, so that a large plant in one location may have a lower unit cost than two smaller plants. This, of course, must be balanced against distribution costs. In examining profit, it is necessary to think in terms of the price and volume of sales at each of the market locations. Given basic data and relationships, the model can be used to optimally locate production facilities or, alter-natively, optimally structure a transportation network given existing locations of plants and markets. It is dynamic to the extent that it can react to changes in volume, price and cost to optimally locate an additional plant, the expansion of existing plants, the shutting down or cutting back of plants, or the restructuring of distribution networks."

Jan 1, 1970

By J. I. Gazzarri

A model of solid oxide fuel cell AC impedance behaviour has been developed and is used to simulate the frequency response of a single cell with and without mechanical damage. The results indicate that the presence of mechanically induced damage within the components of a solid oxide fuel cell can be detected by comparing the frequency response of the undamaged cell with that of a cell in which in-plane cracking or delamination has occurred. The presence of such defects manifests itself as a new semicircle in the Nyquist impedance diagram of the full cell. A parametric study reveals the resolution capabilities of the method in terms of the geometrical characteristics of the defects.

Jan 1, 2005

By Li Qihou, Li Yuhu, Liu Zhihong, Liu Zhiyong, Yang Xiaofeng

Scorodite samples were synthesized, in adding or without crystal seed respectively by using Atmospheric Scorodite Process (ASP), Hydrothermal Scorodite Process (HSP), and Improved Atmospheric Scorodite Process (IASP) individually; and their crystal structure, crystallinity, morphology, particle size, specific surface area, Fe/As mole ratio, as well as the leaching stability were characterized, aimed to reveal the relationships among the synthesis methods, the compositional and structural properties, and the leaching stabilities of scorodite. The results show that synthesis methods have significant effects on the compositional and structural properties of scorodite. Scorodite samples of high crystallinity, small specific surface area, and low Fe/As mole ratio, possess high leaching stability. The order in the leaching stability of scorodite samples synthesized in this study is as follow: ASP<HSP<IASP. Scorodite particles in the sample synthesized by IASP without crystal seed are in large sizes and of pyramidal morphology enclosed mainly by crystal planes of {111}; and the sample possesses the crystallinity of 84.5%, the particle size (D50) of 28.2 m, the BET specific surface area of 3.72 m2/g, and the Fe/As mole ratio of 1.05; after leaching this sample by using acetate buffer solution of pH 4.95 for 10 days, the total arsenic concentration in the leaching solution is merely 1.14 mg/L.

Jan 1, 2015

By R. K. Borden

Rio Tinto is committed to proactive mineral waste and acid rock drainage management. Corporate requirements are closely aligned with the GARD Guide principles of early geochemical characterization and prediction followed by selection and implementation of management strategies to prevent or minimize ARD. Each operation is required to design and implement an ARD and Mineral Waste Management Plan. Successful implementation of the plan requires commitment at all levels of the company, from senior management, to geologists, mine planners, environmental staff and equipment operators. Examples of the successful integration of ARD management strategies into mine operations are cited from several mines.

Jan 1, 2011

By W. W. Rudolph, L. N. Trevani, P. R. Tremaine

UV-visible spectroscopy, Raman spectroscopy, and vibrating tube densimetry have been used in our laboratory to determine equilibrium constants of aqueous species at temperatures as high as 325 °C. The UV-visible and Raman spectra of solutions containing metal complexes and ionized acids or bases can be used to yield formation constants by applying curve fitting methods to resolve the contribution of each species. Colorimetric pH indicators identified by Johnston and coworkers at the University of Texas (Austin) provide an alternative means of determining ionization constants and the pH of complex mixtures. High precision density measurements over the same range yield standard partial molar volumes, which are key parameters for "equations of state" for aqueous species. Examples are given for the copper-ammonia system, simple carboxylic acids, and the iron-sulphate system.

Jan 1, 2004

By M. E. Bilir

In this paper, we review cases in which dramatic and visual swelling problems are experienced in underground structures. Swelling rocks have caused many problems in underground engineering projects. They pose severe problems to the design, construction and maintenance of underground openings. If an appropriate integrated design procedure, which proceeds from exploration, tests, analyses and realistic assumptions of swelling behavior, is used during the design stage, the execution of the project can be completed without any serious delays or dramatic design changes. The case histories were subdivided into three classes that include tunnels, underground coal mines and others. For the evaluation of cases, the surrounding rocks, swelling minerals, water inflow, swelling test results and swelling problems were considered. The main purpose of this review is to inform the reader about potential problems with swelling phenomenon and to emphasize the rehabilitation and extensive cost which are encountered due to the lack of necessary integrated design approaches.

Aug 1, 2013

By Bernard Dallaire, Jean Cayouette, Sylvain Duchesne

"Louvicourt Mine's concentrator, located near Val d'Or, Quebec, treats an average of 4,300 tonnes of ore per day composed mainly of copper, zinc, gold and silver. An analysis of concentrator revenues and metallurgical losses shows a potential for additional gain, particularly in regards to precious metals (kustelite) where recovery is usually around 67 -70 %. The planning, installation and trial operational period of two Outokumpu SK-240 flash cells at the underflow of the primary cyclones took two years. The use of (( flash flotation )) technology has made it possible to exploit the favourable conditions at the underflow of the primary cyclones such as precious metal concentration and the presence of liberated coarse chalcopyrite. These conditions permit early flotation (fresh surfaces) of the kustelite and the liberated copper. Since the start-up of the flash cells, the metallurgical gains have turned out to be very positive with increases in metal recovery reflected in appreciable NSR gains. Also, significant savings in reagent consumption and a coarser copper concentrate have made it possible to reduce the drying cycle of the Larox filter presses since the cells were put into operation.BACKGROUNDLouvicourt Mine is operated by Aur Resources Inc. (30% ownership) on behalf of its partners Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corp. (25%). The mine is located in northwestern Quebec about 600 km north of Montreal and about 25 km east of the mining town of Val d'Or. The mine commenced commercial production in July 1994.The massive sulphide ore deposit lies at depths varying between 450 m and 900 m. Mining reserves (2% Cu equi. cut-off) as of Jan. Is', 2000 are estimated at 7.5 million tonnes of ore averaging 3.4% Cu, 1.8% Zn, 28.0 g/t Ag and 0.9 g/t Au. Delineated ore reserves permit the use of a mechanized transverse blasthole mining method. The extraction order is a typical 1.3.5 mining sequence. Primary and secondary stopes are 15 m wide, 15 to 70 m long (25 m long average) and 30 m high. Backfilling for pillar recovery and regional stability is required."

Jan 1, 2001

By H. Lundberg

Introduction The world has been suffering from an excessive production of all kinds of raw materials, and the metals and petroleum are no exception. As a consequence, at the moment, the urge to find new mineral deposits is almost non-existent and prospecting languishes. But from previous experience we know that sooner or later new supplies will be needed. Mineral deposits become exhausted, and to keep up the supplies of our metals and petroleum, new deposits must be found. Even now, a supply of petroleum of domestic production would not be unwelcome in Canada. It is not, therefore, so entirely malapropos to discuss means of finding ores and oil as it would seem. Almost any physical property connected in definite manner with minerals and rocks may be made the basis of geophysical exploration. This is particularly true of electrical resistivity, and its utilization in electrical prospecting has been the deciding factor in the discovery of such big ore-bodies as Buchans mine, Newfoundland, and the large copper ore-bodies in northern Sweden, etc., as well as in the solution of many foundation and structural problems. The importance of electrical prospecting has been growing steadily, and already there exists hardly any exploration project involving geological problems which may not profit by its application. Electrical prospecting is marching on, and neither temporary failures, nor incompetence, nor over-optimism, nor ill-will and pessimism, nor bad times and business depression, will be able to halt its progress.

Jan 1, 1931

By E P. Graham

Orebodies occur in an infinite variety of grades, shapes and sizes, and take many millions of years to grow. When extraction starts there is only one possible end -the mine sooner or later will run out of ore and shut down. If the mineral industry is to supply the ever increasing demands of modern civilizations, more and more metals must be found and mined. This will require a never-ending search for ore, and the development of every economic body, large or small. To justify the mining of a small orebody, it first of all must pay its way. If the size of the burden imposed by the capital cost estimates is not carefully worked out, an otherwise promising situation could be killed. The very nature of mining, as a transient industry, re-leases a steady stream of good used equipment, and the trained personnel to install and operate it. All manner of plans and layouts, which can be utilized at a new property, are available. Working these and other economies into the estimates will sometimes make enough difference to give a prospect the green light.

Jan 1, 1964

By Ivor da Cunha

Ontario Mining Association (OMA) represents 57 members that are engaged in exploring, producing & processing mineral resources in an environmentally responsible manner. Conservation Bureau at the Ontario Power Authority (OPA) develops, coordinates and stimulates commitment to electricity conservation and demand management programs ? OMA selected compressed air optimization for high impact cost savings and energy efficiency potential ? Ontario Power Authority (OPA) provided $218k funding for $532k project ? Commenced summer 2006, Final Report June 2007 ? Three representative sites participating: ? Williams, CVRD Inco & FNX McCreedy ? Different levels of energy management ? Small, medium and large mining operations ? Different corporate practices and culture

May 1, 2007

By David G. Almond

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations having large SAG mills fitted with variable speed drives. Problems associated with effective operation of this equipment has created the need for better operator knowledge of mill load behavior and the need for new instrumentation capable of providing accurate information about load movement and composition. This paper discusses two performance enhancing instruments available to address these needs.INTRODUCTIONThe economic demands of new mining projects has resulted in increased equipment sizes and this is particularly evident in milling where there are now many SAG mills operating in the range of 28’ – 40’ diameter with installed powers of 8 – 22 MW. These mills are designed to process very high capacities of ore daily2 and the variable characteristics of many of the deposits mined results in the need to vary the mill speed during processing to cater for the changes in ore hardness. Mill speed changes often result in operational problems associated with high-energy impacts striking the mill liners reducing energy efficiency as well as degrading the grinding media through breakage, accelerating liner wear and in extreme cases even breaking liners. These operational problems have given rise to the need to have instruments aimed at providing operators with accurate information in real time about the load composition and movement within SAG mills.The original concepts for operating SAG mills were derived from past experience of operation of conventional fixed speed ball mills. However, the relatively stable conditions that applies with fixed speed and constant ball charge in ball mills supports theoretical approaches to the grinding process based on energy calculations such as Bond’s Work Index concept. Later a set of parameters Si and Bij were used for describing load kinetics, but all of these methods neglect the details of load movement and how the energy is actually used inside of the mill. It is now commonly accepted as a basic rule that SAG mills grind by impact whilst ball mills grind by attrition and consequently SAG mills are designed and operated to generate a large amount of impacts by the cataracting load without paying sufficient attention to where these impacts are actually occurring. Many mills are operated on the basis that as long as the mill is consuming the expected power there is little attention given to the class of bodies using this energy and this often results in the inefficient use of energy."

Jan 1, 2005

By N. Afrin

The microstructure and tensile properties of AZ31B-H24 magnesium (Mg) alloy after friction stir welding (FSW) were evaluated. The grain size was observed to increase from approximately 5 µm to about 9 µm after FSW. The obtained Hall-Petch type relationship showed a strong grain size dependence of the hardness values. While the FSW led to about half of the yield strength of the base magnesium alloy, the ultimate tensile strength after FSW could reach about two thirds of that of the base alloy. The hardening capacity of the FSWed samples was about twice of that of the base alloy. The strain hardening exponent of the base alloy was found to be about 0.1 whereas it became larger than 0.3 for the FSWed samples. After yielding the base alloy showed a high initial and almost constant work hardening rate, corresponding to linear hardening stage II, followed by stage III with a decreasing hardening rate. Stage II linear hardening was observed to be absent in the FSWed samples.

Jan 1, 2007

By Christoph Mueller

Broad band mine communication traditionally is characterized mainly by individual solutions, which have in common their long development phases and their high cost for development, operation and service. The use of Ethernet and the TCP/IP family of standardized protocols provide an uniquely price efficient combination of high bandwidth open networking, universal use and accessibility of price efficient development tools, especially because it forms the technical infrastructure for the worldwide Internet. TCP/IP and Ethernet assures reliable networking however it is not able to guarantee the latency timing of forwarding network information. Therefore, the network design requires strict load limitation and application level traffic control especially if moving equipment has to be manually remotely controlled via the network. The paper discusses the technologies the application of Ethernet and WLAN in underground mining environments.

May 1, 2006

By W. G. Hubler

It has been within only the last two or three years that enough progress has been made in preferential flotation to warrant metallurgists in recommending the installation of commercial-sized plants for the treatment of copper-zinc-iron ores. Until the new processes had been worked out successfully, the treatment of this type of ore had proved a stumbling block in the path of metallurgical progress. Separation of lead-zinc ore is comparatively simple. A lead-zinc ore low in iron may be separated and concentrated by gravity con-centration, provided it is not necessary to grind too fine. Owing to the specific gravity of chalcopyrite and sphalerite being so nearly the same, however, their separation by gravity concentration is out of the question. Complex lead-zinc-iron ores in which the several minerals are intimately associated, requiring fine grinding to free them, have been successfully treated by flotation for the past fifteen years. Galena is easily floated, and its flotation, unlike that of chal¬copyrite, is not affected by the reagents used to inhibit the flotation of sphalerite and iron sulphides. When an attempt was made to use the methods of lead-zinc se-paration on copper-zinc ores, it was found that the depressant re-agents added to inhibit the flotation of the iron and zinc minerals would, under certain conditions, depress a large part of the copper. It was also recognized that, in the grinding of copper-zinc ore, soluble salts were generated which were detrimental to flotation unless properly controlled. The main part of this paper will be a discussion of solutions in the grinding circuit in relation to the pro¬duction of soluble salts and their effect on flotation.

Jan 1, 1931

By C. A. Ingram

The Cigar Lake ore body is a high-grade uranium deposit situated within water-saturated sandstone. In order to extract the uranium ore remotely, ensuring minimal radiation dose to workers, and also to access the ore from stable ground, the Jet Boring System (JBS) was developed. This method of mining involves drilling a pilot hole up through a frozen ore body and utilizing a high-powered water jet to mine out cavities. During the mining process an ultrasonic sensor will be used to provide feedback to the operator, who is located beneath the ore body, as to the dimensions of the cavity. However, more precise data is required to determine final shape, volume, and location of the cavity for mine planning purposes. Selecting a device that will provide sufficient range data in the challenging environment will be vital to optimizing the mining process. Major issues include fog build up and flying debris during mining, and an environment that is wet, dark, and cold A test cavity has been designed and constructed at the Saskatchewan Research Council (SRC) so that a study comparing three different technologies, as prospective candidates for the survey system, can be conducted. The devices being evaluated include a Senix ultrasonic sensor, an MDL Cavity Auto-Scanning Laser System (C-ALS), and a MESA Time of Flight (ToF) camera. The ultrasonic sensor is known to provide range data in foggy conditions but has low accuracy. The C-ALS has been developed for surveying remote cavities but is expensive and does not provide reliable data in fog. The ToF camera provides a high volume of data in a short time period, with potential to provide accurate information in extreme conditions, but has not been tested in a mine cavity application. Iterative closest point (ICP) registration is applied in an attempt to create a 3D point cloud from the scan data and to also compute rotation and translation of the ToF camera. This paper presents an overview of the challenges involved in conducting a survey within a JBS mined cavity, the analysis used to determine the suitability of each device, and the data collected from the test cavity.

Aug 1, 2013

By J. A. Morgan, W. A. Barclay, J. C. Pedersen, I. C. Campbell, D. S. Bubar, R. P. Taylor

"Abstract - The Lilypad Lakes property is host to a group of Ta-mineralized dikes that occur over an area of at least 10 km2. Field relationships are consistent with a syn- to late syn-tectonic timing for their emplacement (with respect to the major regional D1 episode of deformation), with several of the dikes exhibiting a steeply dipping, open, S- to M- to Z-shaped fold geometry. Individual dikes range up to 30 m wide (Rubellite Dyke, Pollucite Dyke), have strike lengths of up to 750 m (e.g., JJ Dyke), and are continuous to depths of greater than 250 m (e.g., Rubellite Dyke, Pollucite Dyke). Typically, they display sharp intrusive contacts characterized by the development of thin, holmquistite-rich haloes. The Tamineralized dikes are comprised of silica- and alumina-rich, sodic, granitic pegmatites that display extreme levels of geochemical fractionation (K/Rb typically < 10.0, as low as 2.2; Nb/Ta typically < 0.20, as low as 0.03), and enrichments in an economically important group of lithophile elements, most notably Li, Rb, Cs, and Ta. Geochemical assays of individual surface grab and drill core samples have yielded values as high as 1.51 wt.% Li2O, 1.25 wt.% Rb2O, 6.21 wt.% Cs2O, and 0.108 wt.% Ta2O5. Diamond drilling has established the presence of wide (~20 m), potentially ore-grade intersections of Ta mineralization (>0.045 wt.% Ta2O5) in both the Rubellite and the Pollucite Dykes.Three Ta-oxide minerals (microlite, wodginite, manganotantalite) of primary origin predominate in the Ta-mineralized dikes, where they occur as fine, disseminated grains in the albite-rich pegmatite matrix. The sequence of crystallization is typically manganotantalite wodginite microlite, which conforms to a well-established paragenetic sequence for rare-element granitic pegmatites in general. All three of the primary Ta oxides are characterized by a high degree of chemical purity (e.g., average Ta concentrations in microlite from 77-79 wt.% Ta2O5), a compositional feature consistent with the extreme levels of geochemical fractionation characteristic of the host granitic pegmatites, and one that indicates that the Lilypad Lakes pegmatites are likely to produce Ta mineral concentrates of the very highest quality.Locally, a second generation of Ta minerals is present, restricted to small vugs in the pegmatite matrix that are surrounded by fine aggregates of K-rich mica or clay. The secondary Ta minerals are dominated by microlite, which is typically intergrown with fluorite and Fe-sulphides, and is distinguished from its primary counterpart by its lower Ta content (around 70 wt.% Ta2O5) and much higher concentration of uranium (up to 9 wt.% UO2). Also, secondary microlite consistently yields low analytical totals from electron microprobe analysis, suggesting that it is H2O-rich. The presence of this second, vug-related generation of microlite, together with the occurrence of localized networks of crosscutting fractures that host high concentrations of Cs and Rb (in the minerals pollucite and Rb-Kfeldspar), suggests that a late-stage, fluid-dominated metasomatic/hydrothermal event may have been important in certain sections of the dikes, and has effected a redistribution of the economically important elements Ta and Cs."

Jan 1, 2005

By Michel Lefebvre, André Piché

Every organization performing R&D is faced with the challenge of introducing new technologies to its operations. Difficulties must be overcome if companies are to realize the benefits anticipated from such developments. This paper outlines the difficulties encountered in transferring to operations various technologies developed at the Mining and Exploration Division of the Noranda Technology Centre. The approach used in the selection of a privileged partner for the technology transfer, the criteria motivating the choice and the process followed to establish the partnership are presented.

Jan 1, 1997

By Andrew Barnes

The adsorption capacity of peat collected from a proposed mine development in northern Sweden has been determined using laboratory column experiments in which peat was irrigated with a simulated (acidic) waste rock dump leachate. The simulated leachate was made using a hydrogen peroxide leach of composite waste rock from the proposed mine development. The waste rock samples were composited in proportion to their predicted extractable tonnage for the mine development in order to generate a more representative leachate solution for the waste rock facility. As expected the test revealed that the peat material shows a very high affinity for attenuation with greater than 70% of Co, 90% of Ni and 95% of Cu removed from influent solutions through the majority of the tests demonstrating the potential benefits in mine water treatment. In contrast, it was found that Fe is initially released from the peat at concentrations up to 100 mg/L and can mean potential problems for the water released depending on the receiving environment. The exact mechanisms for Fe release is uncertain, though it is suspected that ion exchange / competitive desorption is responsible. Inspection of the laboratory results and drainage data from the natural peat wetland receiving drainage during overburden prestriping and mine development at the mine site are comparable, confirm the validity of the experiments, and further emphasize the potential for future use of pre-stripped peat material in managing water quality.

Aug 1, 2013

By R. L. Stanton

"The present contribution is complementary with a preceding one on the field association of the conform-able ""pyritic"" deposits. It considers the more important features of their mineralogical constitution and their microtextures, re-examines the present interpretations of these, and of-fer-some alternative explanations. The term ""pyritic"" for these de-posits is m many cases a misnomer, as two quite distinct ore types are inuolve. One is a banded pyritic sphalerite-galena-chalcopyrite ore (for which the term '•pyritic"" is in-deed quite suitable), while the other is non-banded and is composed essentially of pyrrhotite and chalcopyrite. In addition to these constitutional differences, each is distinctive in general appearance and texture. The occurrence of two such consistent but clearly distinguishable ore types is attributed -rather than to difference in source material and pressure-temperature conditions of deposition -to the contribution of similar source material to dissimilarly oxygenated environments of sedimentation. Textures in the banded ores generally thought to be indicative of replacement or of high-temperature exsolution are explained by slow, law-temperature segregation in situ during compaction, folding, and regional metamorphism."

Jan 1, 1960