Search Documents

By Tapio Leskinen

"l. IntroductionA reliable sampling system is the basis for an on-stream analyzer. This was realized in Outokumpu company when the development work of the Courier 300 On-Stream X-ray analysis system was started. Because Outokumpu Oy is a mining and mineral processing company, its engineers have been able to thoroughly test sampler prototypes in actual operating situations. The sampler development has been going for several years in close co-operation between company's concentrators, the Institute of Physics and the Instrument Division of Outokumpu Oy. The most active part of the work was done between 1969- 1972. Besides the reliable operation of a sampler special attention was paid to the representatively of the samples taken by the samplers. 2. The Courier 300 Sampling SystemThe sampling system comprises up to fourteen sampling circuits in one Courier analysis system. Each circuit consists of the following components:1. Primary sampler 2. Secondary sampler 3. Cleaner screen 4. Feeding tank5. Sample cell6. Timer-controlled sampler7. Pumps, sumps and pipesSecondary samplers, cleaner screen and feeding tanks are included in the secondary sct1npling system. The sample cells are located in the spectrometer cabinet of the analyzer."

Jan 1, 1976

By G. R. Dunning, M. R. Wilson

"Abstract - The early Paleozoic accretionary tectonic regime that was established along the Laurentian margin of the Newfoundland Appalachians provided a favorable setting for shear-hosted gold mineralization along a major terrane suture, the Baie Verte-Brompton Line. The Stog’er Tight prospect is one of several mesothermal-style gold occurrences hosted by shear zones within accreted ophiolites and oceanic arc terranes on the Baie Verte Peninsula. It is an epigenetic, stratabound deposit that is confined to shallow-level gabbro sills within the volcanic cover sequence of the allochthonous Point Rousse ophiolite complex. Gold mineralization at Stog’er Tight is associated with hydrothermal mineral assemblages represented by chlorite-calcite, sericite-ankerite, red albitepyrite (±Au) and chlorite-magnetite alteration zones. Gold occurs with pyrite within the intensely altered gabbro, along the margins of syn- to late-shear, quartz-rich, replacement veins.The Stog’er Tight gabbro served as a rigid body conducive to shear deformation and fluid penetration, whereas, its high Fe-Ti oxide content induced fluid oxidation and gold-pyrite precipitation. Hydrothermal alteration involved progressive CO2, S, Na, and LILE metasomatism, along with significant enrichments in the REE, HFSE, and Th in the high-grade ore zone. Temperatures of vein formation and alteration are constrained by oxygen isotope thermometry to be between 250°C and 480°C. Isotopic compositions of vein quartz from the Stog’er Tight prospect are uniform (??O = +12.5 ± 1‰) and fall within the range cited for many shear-hosted, auriferous quartz veins.A U-Pb zircon igneous age of 483 +3/-2 Ma for the Stog’er Tight gabbro is consistent with its stratigraphic correlation with other Ordovician ophiolitic and volcanic arc/back-arc assemblages in Newfoundland. The U-Pb age of a rare variety of hydrothermal zircon recovered from the high-grade ore zone directly constrains the timing of gold mineralization to 420 ±5 Ma, in accord with a major orogenic episode of Silurian age that produced many of the magmatic and metamorphic rock suites in north-central Newfoundland. Our results are consistent with a post-peak metamorphic, late-magmatic model for gold mineralization that occurred during the waning stages of Silurian orogenesis, driven by emplacement of I-type granitoid intrusions into the crust."

Jan 1, 2000

By Jesús L. Valenzuela, José R. Parga, Salvador Aguayo, Héctor Moreno

The Merrill Crowe zinc-precipitation process has been applied worldwide on a large number of operations for the recovery of gold and silver resulting in a higher consumption of zinc dust from cyanide solutions. However, in some of plants this precipitate is of low quality, because lead, cadmium and especially copper are precipitated along with gold and silver. The low quality precipitate also requires more fluxes in smelting and shortens crucible life. In this study, a process is introduced to remove copper, silver, lead and cadmium from barren solutions following the Merrill-Crowe process. Copper and silver are removed by precipitation in a serpentine reactor, using sodium sulfide as the precipitator, and sulfuric acid for pH control. The recovery of lead and cadmium ions with natural hydroxyapatite using cow bone powder (CBP) as a new adsorbent material, is introduced. CBP is capable of removing lead and cadmium ions from aqueous cyanide solutions with 99% efficiency. It has the ability to compete with other existing commercial adsorbents for the removal of lead and cadmium. Results show that pH value has a significant effect on copper cyanide removal efficiency, and it was determined the optimal pH range to be 2 - 3. At this pH value, the copper cyanide removal efficiency achieved was up to 99 %; and for the cyanide associated with copper cyanide complexes, the recovery was 90%. Finally, the precipitate quality was improved 400% .This procedure was successfully run at three mines in México.

Jan 1, 2014

By L. S. Brooks

TIMBER HANDLING presents a problem for any mine where appreciable amounts are used. This problem is accentuated where the shaft compartments are too small to allow a loaded timber truck to be lowered in the mine cage. When Normetal Mining Corporation, Limited, found it necessary to resort to square-set mining it faced this problem of getting large quantities of timber down a shaft that was also required for hoisting ore. A 'timber car' that could be suspended under the cage was developed to overcome this difficulty. Production started at the Normetal mine in 1937, at the rate of 250 tons per day. In 1938 a winze, known as No. 3 shaft, was sunk from the 800-foot level ?to the 1,385-foot level. This was later raised to surface and then deepened to 3,275 feet in three stages and became the main production shaft. The portion of the mine below the 3,070-foot level is serviced by a winze, locally referred to as No. 4 shaft, which has been developed for stoping down to the 3,990-foot level and which has been deepened to the 5,365-foot level. No. 3 shaft has two hoisting compartments, each 4 ft. 6 in. by 5 ft. 0 in. inside the timbers, through which the ?ore must be hoisted and timber and supplies lowered.

Jan 1, 1956

By Kevin J. Palmer

The introduction of the National Instrument (?NI?) 43-101 Standards of Disclosure for Mineral Projects has led to some very specific requirements to reporting a Mineral Resource estimate for mineral projects to the public. There are elements of the Mineral Resource estimate that are based on the qualified person (?QP?) completing the work to accepted industry practices and applying their relevant experience. There is no document that defines what is considered the accepted industry practices. There are guidelines provided by the Canadian Institute of Mining, Metallurgy and Petroleum (?CIM?) but, in general, the industry practices are dynamic and often different QPs will estimate the same mineral project in different ways. This sometime happens on exploration projects as they proceed from one study to the next. The focus of this paper is to provide a review of some of the current practices that are published in Technical Reports (Preliminary Assessment to Feasibility studies) with respect to classifying a Mineral Resource as Inferred, Indicated and Measured and the grade interpolation and modeling methods, data support (i.e. geological drill hole spacing) and validation methods employed.

Oct 1, 2010

By D. K. Sarkar, Ying Huang

"Superhydrophobic thin films were fabricated on aluminum alloy substrates by chemical etching followed by passivation with organic acid molecules; (ii) electrophoretic deposition (EPD) of functionalized ZnO nanoparticles and (iii) electrodeposition of organic-inorganic composite materials. The physical and compositional analyses of the deposited thin films were characterized by SEM, FTIR, XRD as well as contact angle goniometer. The contact angle and surface roughness of the superhydrophobic surfaces prepared by the chemical etching process were found to be 156° and 2.29 µm, (ii) by the EPD process were found to be 155° and 4.54 µm and (iii) by the electrodeposition process were found to be 159° and 7.11 µm, respectively.The corrosion properties were analyzed with both polarization and electrochemical impedance spectroscopy (EIS) in NaCl aqueous solutions. The results demonstrate that the superhydrophobic thin films on aluminum alloy substrates display better anti-corrosion behavior than the as-received aluminum substrate. The comparison of results pertaining to the compositional and corrosion properties of these thin films on aluminum will be discussed in this work.INTRODUCTIONSuperhydrophobicity is defined as a surface property which provides non-wetting characteristics with a water contact angle larger than 150°. It is observed that the creation of certain micro-nanoroughness structures promotes the entrapment of air in the spaces of the rough surface morphology. In addition, lowering the surface energy helps to reduce the affinity of water drops to the surface, thereby weakening the water-surface interaction. Recently, various fabrication methods for superhydrophobic surfaces have been explored (Sarkar, 2010, Huang, 2010, 2011, 2013, 2015a, 2015b), such as the sol-gel process (Brassard, 2011), plasma treatment (Marchand, 2013), chemical vapor deposition (Zheng, 2009), chemical etching (Saleema, 2011), electrodeposition (Ying, 2011) and electrophoretic deposition (EPD; Huang et al., 2015b)."

Jan 1, 2016

By H. Harzer

Statistics Canada record s indicate that in recent years 70 to 80% of the entire Canadian coal production originated from Western Canadian mines, in which about 55 to 65% of the coals are bituminous. Until recently, less than 20% of the latter were extracted by underground methods , the remainder being surface-mined. However, it is estimated that within the foreseeable future up to 80 or 90% will have to be gained by underground techniques. Although Western Canadian coal resources are considerable, they are unfortunately locked in severely distorted, steeply pitching and faulted seams of variable thickness. Consequently, their economic extraction poses serious engineering problems. One possible solution to the problems is to apply hydromechanical methods to underground mining. This is a well-proven method shown to be economically viable under Western Canadian conditions. This paper endeavours to widen the scope of published data on hydraulic coal mining and is based on practical engineering and cost data gathered through contacts with West German designers and operators of hydraulic mines.

Jan 1, 1978

By Donald Leroux, Jean-François Wilhelmy, Ahmed Bouajila

"A young private R & D organization, COREM celebrated its 10th anniversary in 2009. Managed by a consortium of nine mining and metallurgical companies, COREM has the mandate of increasing the competitiveness of its member companies through the development and transfer of mineral processing innovations. Typical technologies developed by COREM include alternative mineral processing techniques, novel operating strategies, innovative sensors and process simulation software. Many of them were developed in partnership with universities and selected research organizations.Because the COREM membership base is broad (from ferrous to base, to precious metal industries), its R & D program must deliver technologies with applications within a wide spectrum of mineral processes. Comminution, physical (gravity and magnetic) separation, flotation, cyanidation, pelletizing and thermal processes are the main topics of the R & D program. A number of new technologies have been developed and transferred to the plants of member companies. These examples of transferable technologies demonstrate the capability of COREM to impact the bottom-line of its member companies.INTRODUCTIONCOREM is a private mineral-processing R & D organization that operates from its own laboratories and pilot-plant with its own staff of professionals and technicians (about 95 persons). It is managed and financially supported by a consortium of nine mining and metallurgical companies and three provincial and federal ministries. The very ‘down-to-earth’ mission statement of COREM is to increase the competitiveness of the mineral processing plants of its members. The eighteen plants upon which the COREM technology development program is currently based can be found in Québec, Newfoundland and Labrador, New Brunswick, the Netherlands and Botswana."

Jan 1, 2010

By M. Al-Khawaja, F. Hassani, F. Mucciardi, N. Razavinia

"In today’s economy many industries are becoming aware of the need to recover some of the waste heat they create. Industrial processes release, on a global scale, over 100 tera-Joules (i.e. 1014 J) of waste heat annually. The recovery of waste heat can lead to a reduction of greenhouse gas emissions and it can also provide a financial benefit which can be obtained by converting some of this excess heat to electricity. At McGill, a research program has been initiated so that low grade waste heat (temperature between 100ºC and 300oC) from process off-gases found in pyro-metallurgical industries is captured and concentrated by using heat pipes and then converted to electricity by a mechanical engine. This paper illustrates the 3 C’s process (capture, concentrate and convert waste heat to electricity). It also provides some preliminary experimental data. INTRODUCTIONThe problematic climate change caused by the use of fossil fuels, the rapid depletion of global reserves and the catastrophic consequences of nuclear power generation call for renewable and safe, resources of energy, for both man and the environment. Extensive researches in the production of energy from renewable sources and improvements in efficiency of current technologies can help us to reverse this trend.The greatest advantages of using renewable energies are that they don’t deplete and they also contribute to a green environment. On the other hand the disadvantage of using these resources is that the energy available from renewable sources is much less concentrated than that provided by fossil fuels and nuclear energy. This makes renewable energy less attractive for large scale industrial uses in most cases. A key target for society for the 21st century is the production of energy from renewable sources at a cost that is competitive with fossil fuels. Fossil fuels represent a concentrated form of energy; usually it is referred to as high grade energy. Nonetheless, there is a vast supply of alternative energy. The sun, wind, water and biomass were the first to be explored. While these are all valid options that warrant concerted efforts and large investments, there is another source of energy that typically is produced by manufacturing industries. This energy is often referred to as low grade waste heat. Most of this energy is simply vented to the environment through the stream of off-gases. In the future it will be necessary to capture and convert some of the low grade heat to a valuable form such as electricity if we are to improve on the efficiency of energy usage."

Jan 1, 2012

By C. O. Staples, J. G. Morrow

The application of cationic flotation to the upgrading of magnetic concentrates was investigated in the laboratory by both batch and continuous test procedures. It was found that the collection of coarse gangue particles with amine, heretofore considered a serious obstacle to this particular application of cationic flotation, is greatly enhanced by a drastic reduction in what might otherwise be considered normal impeller speed. Gangue flotation is in-dependent of variations in the rate of aeration. The collector and Crother additions and the impeller speed which favour the formation of a matte froth yield optimum results.

Jan 1, 1966

By R. A. Hemstock

"Simple classification systems are now being used which will describe adequately the surface vegetation, the topography and the peat for any muskeg condition. Good progress is being made in determining some of the mechanical properties of muskeg and it is apparent that the science of soil mechanics will apply largely to these studies. Correlation is also indicated between shear strength as determined by the shear vane tester and vehicle performance. Several tracked vehicles are now available which perform well in muskeg and advances in this field have come rapidly in the past few years. Testing is under way on the largest of all muskeg vehicles -the thirty-five ton Musk Ox. This vehicle will fill the last gap for the oil industry and will make possible the movement of large drilling rigs at any season of the year."

Jan 1, 1960

By V. A. G. Preto, W. H. White, J. E. Harakal

Potassium-argon age dating performed recently on intrusive rocks from Copper Mountain indicates that the satellite Smelter Lakes and Voigt stocks have radio-metric ages which are indistinguishable from that of the Copper Mountain stock, as determined by Sinclair and White (1967). The complex of intrusive rocks known as the Lost Horse Intrusions also yields essentially the same radiometric age, as do biotite-sulphide-pegmatite veins on Copper Mountain.

Jan 1, 1971

By J. R. Kadambi, E. Kucukal, J. Furlan

"Hydrocyclone separators are used in various industrial applications, including mining milling and tailings systems, in order to separate or classify solid particles and liquid droplets from multiphase systems. The flow within a hydrocyclone commonly used in the mineral processing industry was investigated numerically and experimentally using Particle Image Velocimetry (PIV) and refractive index matching techniques. The computational simulations were performed using a commercially available CFD package, STAR CCM+. Two turbulence models were used in the numerical calculations: the k-? model and the Reynolds Stress Model (RSM). In both cases, the first order discretization scheme was unable to resolve the flow characteristics accurately due to the high levels of numerical dissipation. PIV measurements were taken at various spatial locations along the cyclone. Both the numerical simulations and PIV data demonstrate that tangential velocities tend to increase when going radially inward from the cyclone wall towards the vortex finder, and reach a maximum value before they begin to decline rapidly and eventually become zero at the wall. The results also demonstrate the utility of non-axisymmetric approaches in cyclone flow simulations for a greater understanding of the fluid mechanics. The computational results were validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles. The comparisons demonstrated good agreement between the two models.IntroductionHydrocyclones are devices used to separate and classify solid particles or liquid droplets from liquid-solid or liquid-liquid systems. Versatile in application, they have been widely used in many industrial applications including the food, oil, power generation, chemical and mineral processing industries since 1891, when the first hydrocyclone was introduced by Bretney (Park, 2003). Hydrocyclones have a relatively simple design with no moving parts, which leads to an efficient separation process."

Jan 1, 2016

By James D. Bamburak

Total mineral production in Manitoba has averaged C$1 billion over the past ten years. Industrial mineral production has comprised almost 10% of the total, with more than half coming from the aggregate sector. In southeastern Manitoba, tantalum, spodumene and amblygonite concentrates, cesium and rubidium ores, cesium formate, dimension stone and sphagnum peat moss are produced. Gypsum, high-calcium limestone and lime are produced in the Interlake area. Early industrial mineral production consisted of tools and implements, salt and pottery. Historical production has included: salt, building stone, aggregate, lime and dolime, lignite coal, gypsum, natural and Portland cement, calcium bentonite, brick, light-weight aggregate, caustic soda and soda ash, and silica sand. Future industrial mineral production may come from reactivated quarries, pits and wells or from new producers of current commodities. Newproducts may include: stainless steel master alloy, silicon metal, titanium and magnetite, lithium carbonate, float-plate glass and ferrosilicon, "marble" dimension stone, magnesium metal, potash and kaolin.

Jan 1, 2001

By A. Akerman, C. P. O’Connor, N. Vayenas

"Stereolithography is a well-known rapid prototyping technique in the manufacturing sector. Essentially, it is a three-dimensional printing process that produces plastic prototype parts from standard CAD files. At present, Canadian mining companies are not fully aware of the potential of rapid prototyping techniques (RPTs) for their production and mine design systems. Mining engineers and geologists attempt to visualize and understand the characteristics and layouts of orebodies on computer models, and in cases where it is decided to develop physical models, the process is time-consuming, based on simplified constructions. RPTs, such as stereolithography, can facilitate engineers and geologists to quickly, and with satisfactory accuracy, visualize sections of orebodies and evaluate alternative ore extraction techniques using 3D solid models.The research discussed in this paper is carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in collaboration with Inco Limited and the Integrated Manufacturing Technologies Institute (IMTI) of the National Research Council of Canada. The main objective with this research is to evaluate the applicability of state-of-the-art RPTs to underground hard rock mining systems. RPTs can play a significant role in accelerating the design and development process of mining systems."

Jan 1, 2006

By K. Bruce Hodgins

The North American mining industry faces challenging emissions regulations in coming years with the introduction of new standards for off-road diesel engines. In order to remain competitive, industry stakeholders must invest in new technologies that are economically and environmentally sustainable. Westport Innovations Inc., of Vancouver B.C. has developed high pressure direct injection (HPDI) technology that allows diesel engines to run primarily on natural gas with no intrusive engine modifications, reduced emissions of NOx, PM, and CO2, with no loss in performance. This is accomplished through late-cycle high-pressure injection of natural gas directly into a diesel engine combustion chamber. The natural gas is injected at the end of the compression stroke. A small amount of diesel fuel is injected first to initiate combustion, followed by the main natural gas fuel injection. The diesel cycle and its operating characteristics are fully retained including high combustion efficiency, low speed torque, high-power output, no engine knock and fast response to load changes. Natural gas has not been an attractive fuel alternative in mining operations due to reduced performance associated with spark ignition engines and the added weight and space required for compressed natural gas tanks. However, liquefied natural gas (LNG) can be stored in a similar manner and volume to diesel fuel by virtue of its increased energy density over compressed natural gas. Cummins, Inc. of Columbus, Indiana and Westport have formed a joint venture, Cummins Westport Inc. (CWI), under which agreement the HPDI technology is being applied to a Cummins QSK engine series for high horsepower applications such as mine haul trucking. CWI, along with Komatsu Mining Systems, ENRG Fuels, Placer Dome, and Cortez Joint Venture are performing a feasibility study for the development and demonstration of an LNGfueled HPDI QSK engine in a large mine haul truck. The goal would be to demonstrate low emissions consistent with EPA ?Blue Sky? standards, high efficiency based on HPDI technology and good economics resulting from the high fuel consumption of 2,000+ hp trucks.

May 1, 2002

By L. X. Li

Coking coal producers often encounter variations in clean coal quality when mining multiseam deposits containing coals with different washability and coking properties. This paper describes how, for a single coal property, an initial clean coal specification with an ash content of 8.5% on an air-dried basis (ADB) and a free swelling index (FSI) of 5.5 can be improved to a specification with 7.5% ash content ADB and an FSI of 6. This is accomplished by sorting coal seams into two groups for processing and blending. A preliminary economic model demonstrates how this improvement enhances economic returns through a beneficial factor.

Jan 1, 2014

By H. Fujihara, K. Uesugi, H. Toda, A. Takeuchi, K. Shimizu

"Hydrogen is trapped at a variety of microstructures, for example grain boundaries, dislocations and particles. It is thought that hydrogen trapped at trapping sites is redistributed to the other sites under loading and then brittle fracture occurs with hydrogen accumulation. In order to understand hydrogen embrittlement behavior, it is necessary to investigate the time evolution behavior of hydrogen accumulation at each trap site. In the present study, changes in hydrogen distribution are observed under stress using Kelvin force microscopy (KFM) that can visualize hydrogen concentration distribution on material surface at high resolution. Spot-like hydrogen enriched regions are observed on the surface of a material. In addition, hydrogen depleted regions are observed around those enriched regions, and the appearance of hydrogen trap due to particles existing near the material surface is revealed. On the other hand, hydrogen trapped at grain boundary can be visualized. From in this result, it was suggested that crystallographic factors influence hydrogen accumulation. The relationship between initiation and propagation of intergranular crack and hydrogen accumulation under stress will be discussed.INTRODUCTIONHydrogen present in a metal sometimes has significant effects on various properties. Hydrogen in a metal is trapped at a variety of microstructure, for example dislocations and grain boundaries. Grain boundaries, dislocations and micro pores are the major trap sites in aluminum alloys. Some researchers considered that hydrogen redistribution and accumulation between these trap sites in a material with loading plays an important role in the brittle fracture behavior. In general, in intergranular fracture and quasi-cleavage fracture, the hydrogen trapped at grain boundaries and dislocations contributes to fracture behavior, respectively. Recently some researchers have shown that the ductile fracture in aluminum alloys is resulted from growth and coalescence of hydrogen micro pores. Analysis using first principles calculation indicates that intergranular fracture occurs when hydrogen concentration reaches 20 atom H/nm2ongrain boundary. From this report, it is considered that hydrogen redistributed during deformation accumulates locally in order to cause hydrogen brittle fracture. In order to understand hydrogen embrittlement, it is necessary to investigate the time evolution behavior of hydrogen accumulation at each trap site. In the present study, we evaluate the relationship between hydrogen accumulation behavior and fracture behavior in Al-Zn-Mg based alloys. In-situ observation was made by combining the tensile test with Kelvin force microscope (KFM) that can visualize the hydrogen concentration distribution on the material surface with high resolution. We also investigate the relationship between hydrogen distribution behavior and crystal orientation."

Jan 1, 2018

By B. E. Shaw

This paper describes the use of the Free Piston Valve, and a simple hoist brake control system, which has been developed over the last two years, greatly improving the performance of low-pressure brake engines. The basic control system is outlined, with sections devoted to emergency trips and differential braking, and the application of the system to deep shaft hoisting is discussed.

Jan 1, 1966

By Henry Hengeveld

Are the IPCC results credible? The most recent IPCC assessment is??an admirable summary of research activities in climate science? US National Academy of Science 2001 report to President Bush Joint statement by Academies of Science from 17 other countries ? May 2001 ?The work of the?IPCC represents the consensus of the international science community on climate change science. We recognize IPCC as the world?s most reliable source of information?and endorse its method of achieving this consensus.?

Nov 1, 2002