Search Documents

By D. Raicevic

Interest has recently been revived in the recovery of tantalum from the Bernie Lake pegmatite deposit. A gravity concentration process was developed to give satisfactory recovery and concentrate grade. The application of high-intensity magnetic separation was also stud1ed. A pilot-plant investigation that confirmed the laboratory testing and provided a commercial-grade concentrate 1s described.

Jan 1, 1968

By Kr. N. Karparov

Measurements made with high precision GPS landmarks and geotechnical radar Reutech MSR- 300 associated with the observed movements in the north face of Assarel Mine, where on a horizontal distance of 50 m, 2 groups of landmarks indicated different deformation behavior. Measurements are made in order to confirm the applicability of the radar system in regions of complex geotechnical conditions. The standard deviation of each landmark is used as an accuracy standard between the separate measurements of the deformation vectors made by the high-precision GPS system for each landmark. A very good correlation between the displacement vectors can be seen based on the measurements made with the high-precision GPS system and the measurements made by the radar system MSR-300. Geological, engineering geological and hydro-geological conditions of the area of concern are discussed in this paper. The measured deformations and the FLAC/SLOPE analysis show similar results. In the paper is discussed their local character and their sensitivity to other geotechnical and hydro geological conditions.

Aug 1, 2013

By I. Farr, H. Wittens

"In 1989 and 1990 abnormally high levels of arsenic in ore from the Thompson Open Pit Mine threatened Manitoba Division's electro-nickel production. The paper will discuss our development of a flotation process to separate pentlandite and gersdorffite (the prime nickel and arsenic bearing minerals).The presentation will focus on the development of the process from conception, through lab and plant test work, to plant optimization and full scale production. The paper will conclude with the benefits and cost of the completed project.INTRODUCTIONRejection of arsenic from nickel sulphide ores was not a primary concern in the Manitoba Division until 1989. At that time increased production in the Thompson Open Pit mine, which contains high arsenic ore zones, resulted in excess amounts of arsenic in the Thompson Refinery affecting electro-nickel quality. This problem was resolved through extensive efforts by Mill personnel. The purpose of this paper is to familiarize the reader with- the Thompson Mill.- the mineralogy of the Thompson orebody.- the evolution of Ni/As separation in the Mill.- the metallurgical impacts of the separation on the Mill.- the importance of the separation to the Manitoba Division."

Jan 1, 1991

By E. G. Joe

"The continuing increase in costs for power and fuel are affecting significantly the cost for milling of Canadian ores. In order to ascertain the scope and source of energy consumption in Canadian mills for further energy conservation opportunities, CANMET, in cooperation with the Canadian Mineral Processors carried out a detailed survey on the metallic mineral processing plants. Sixty-seven mills representing almost 300 million tons of annual capacity participated in the survey. The results indicated that in general, copper and iron ore mills, representing the bulk of the tonnage, consumed relatively low levels of energy per ton. Nickel-copper, zinc-copper and lead-zinc ore mills were moderate in energy consumption, while uranium and some copper-lead-zinc mills reported much higher energy consumptions due primarily to the increased heat requirements of the ore pulp. While the plant heating costs varied somewhat with the location in Canada, it was apparent that the lowest heating costs were achieved by those built with proper insulation and energy conservation design. If the cost per million British Thermal Units is taken as $2.00, the mill energy costs generally ranged from 40¢/ton up to $1.20/ton.IntroductionEnergy consumption in milling has always been of significant interest to Canadian mineral processors who traditionally calculate their milling costs down to pennies per ton. Even the measure of an ore's grindability is expressed empirically by Bond in kilowatts hours per ton milled. Some of the mills located in isolated areas were obliged to generate their own electrical energy from fossil or petroleum-based fuel at a cost substantially higher than that obtainable from captive or public hydro-electric installations. These mills practiced energy conservation long before the advent of O.P.E.C. energy cost inflation. One example of this was the use of electric boilers to produce process and heating steam during off-peak electrical load periods."

Jan 1, 1978

By R. D. Lindsay

Pamour Porcupine Mines, Limited has been actively engaged in the ''Custom Tolling'' of Gold-Bearing materials throughout the past decade. Experience acquired in this area was utilized to design and commission a custom gold milling facility at its operations in Timmins, capable of:(a) Accepting a bulk ore test sample at the rate of 150 t/d for crushing, sampling, and metals analysis;(b) Processing gold-bearing ores at a rated capacity of 150 t/d, to produce a goldbearing sulphide concentrate;(c) Processing free milling gold ores at a rated capacity of 80 t/d for total cyanidation;(d) Cyaniding custom gold flotation concentrates at a rated capacity of 80 t/d; and(e) Processing of complex gold/copper or carbonaceous ores, requiring an impurity flotation concentrate separation stage prior to cyanidation, at a rated capacity of 100 t/d.Items considered in the process design and development included:- various gold ore types available for processing;- flowsheet flexibility required;- sampling strategy as related to head grade determination and metals accounting; and- contract considerations.This paper highlights how these various considerations were used to design Pamour's ''Custom Gold Milling Facility''.

Jan 1, 1987

By E. G. Joe

The continuing increase in costs for power and fuel are affecting significantly the cost of milling Canadian ores. In order to ascertain the scope and source of energy consumption in Canadian mills for further energy conservation opportunities, CANMET, in cooperation with the Canadian Mineral Processors, carried out a detailed survey on the metallic mineral processing plants. Sixty-seven mills representing almost 300 million tons of annual capacity participated in the survey. The results indicated that, in general, copper and iron ore mills, representing the bulk of the tonnage, consumed relatively low levels of energy per ton. Nickel-copper, zinc-copper and lead-zinc .ore mills were moderate in energy consumption, and uranium and some copper-lead-zinc mills reported much higher energy consumptions due primarily to the increased heat requirements of the ore pulp. Although plant heating costs varied somewhat with location, it was apparent that the lowest heating costs were achieved by those plants built with proper insulation and energy conservation design. If the cost per million British thermal units is taken as $2.00, the mill energy costs generally ranged from 40ft to $1.20 per ton.

Jan 1, 1979

By J. G. Debanne

MOST company-employed petroleum engineers have in their accounting departments punch-card computers that can perform engineering calculations thirty to three hundred times faster than desk calculators, or they can rent such machines from Computing Service centres. These machines not only eliminate the drudgery of desk calculation but also the risks of human errors. The I.B.M. t 604 punch-card computer of Texaco's accounting department in Calgary has been used for oil and gas property evaluations, curve fitting by least squares, statistical core analysis studies, unsteady-state water in-flux studies, phase equilibrium performance prediction of oil reservoirs, gravity segregation calculations, etc.

Jan 1, 1958

By D. Kong, A. Klyashtorin, L. McGilp, I. Wilson

This work reports on applying iron oxide coated sands media in an experimental permeable reactive barrier to remove uranium species from uranium containing water. A field experiment was conducted at the legacy Gunnar uranium mine & mill site that was abandoned in the 1960s with limited to no decommissioning. The flooded Gunnar mine pit presently contains about 3.2 million m3 of water contaminated by dissolved U (1.2 mg/l), Ra-226 (0.4 Bq/l), and minor concentrations of other contaminants (As, Se, etc.). The water is seeping over the pit rim into Lake Athabasca posing environmental and health concerns. Iron oxide coated sands can be used to immobilize uranium species through an adsorption process. Methods for preparation of hydrous ferric oxide sorbents and their supported forms onto silica sands are described. Fourier transform infrared spectroscopy (FTIR), and powder X-ray diffraction (pXRD) were used to characterize the physical-chemical properties of the sorbent. The monolayer uranium uptake capacity (Qm) was estimated through the Langmuir adsorption isotherm. Adsorption kinetic experiments were performed in a lab environment before moving to a field trial. Based on these lab results and the input on field-scale appropriate geometries, a pilot permeable reactive barrier was fabricated and a field test conducted near the Gunnar pit in June 2019. This pilot test provided technical data and information needed for designing a full-scale permeable barrier based on the iron oxide coated sands, which may be applied for in-situ water treatment at Gunnar and other legacy uranium sites.

Jan 1, 2020

By J. W. Merks

"Simulation is the process of designing a computerized model, of a system or procedure, for the purpose of understanding its behaviour and developing strategies to control its operation. Simulation models are rapidly becoming an effective tool for mineral processing plants. Powerful software and fast hardware are more readily available than a basic understanding of the theory of mathematical probability and applied statistics that process simulation models demand.Simple spreadsheet software can be used to develop simulation models that take into account any set of conditions at a mineral processing plant. In addition to an unbiased estimate for each variable in the set on which two-and three-product formulas are based, reliable variance estimates for all variables are required. How to estimate variances, effectively and at the lowest possible cost, and how to compute variances for simple functions such as the metal content of a quantity of ore or concentrate, or more complex functions such as the percentage recovery at a mineral processing plant, are the key to useful simulation models.IntroductionSimulation models for systems and procedures have become one of the most powerful and effective applications for computers( 2.6). Simulations are applied to a wide range of scientific and engineering disciplines. Generally, a model is designed to investigate the effects of changes in and interactions between a set of variables before a system is in operation or a procedure is implemented, by simulating weeks, months, and even years of operation, in a few minutes of computer time. Along with practical and useful applications always comeabuse and misuse. For a simulation process cannot be more reliable than the methodology that was applied to design the model, to estimate variables and variances, to check performance, and to verify validity. A mineral processing plant is a dynamic system that changes continuously as a function of time but within probabilistic constraints that can be estimated by applying statistical tools and techniques to the variables and variances that interact in the system.A model should be designed to simulate not only the set of variables but also the variance for each variable. Models in which constant variances are used to generate normally distributed random numbers, are less realistic than models in which the variances are simulated first, and then used to simulate the variables."

Jan 1, 1991

By D. Royston

In SAG mills fed with a variety of ore types, hard packing between the shell lifters can come and go depending on rock type and rock size distribution and the presence of a binder. Packing can appear in all sizes of SAG mills, and can be tenacious. High ball impact forces (depending on ball size) in larger mills may compact and encourage packing. Packing can have a negative impact on milling performance and a change in shell liner design may be required to remove it. However shell liner design changes need to be managed with care to ensure liner reliability. In smaller mills control of packing can extend shell plate wear-life and may help to maintain milling performance in fixed-speed mills through the liner wear-cycle.

Jan 1, 2012

By D. Bronkhorst, J. Rheault

"Backfill practices at the Williams mine have evolved significantly since underground mining began in 1986. The use of conveyors as a means of transporting fill material to stopes has been discontinued in favour of load-haul-dump equipment. The method of adding binder to the fill product has been refined along with the placement technique. Slurry preparation has been fully automated and flyash is now included as a binding agent. Surface preparation of the fill product has evolved substantially with the quarry operation coming into full operation and the construction of pennanent crushing, screening, and storage facilities. Company personnel have replaced all contracted labour involved in backfill operations. Some changes have been made to achieve a higher standard of quality control while others were implemented as a matter of cost reduction. BackgroundThe Williams mine is one of three mines operating at the Hernlo gold deposit, located 40 km east of Marathon, Ontario, along the north shore of Lake Superior. Daily production at the mine is 6000 Ud yielding an annual gold production of approximately 500 000 oz. The orebody extends from surface to a depth of 1300 m dipping north at 70 degrees. The average orebody width is 25 m, but varies from 45 m on the eastern boundary to about 10 m at the western probable limit and at depth. Proven and probable reserves currently stand at 32 million tonnes grading 6 g/t.The Williams orebody has been divided into four separate mining zones: the A-zone, the West-of-Dyke zone, the B-zone, and the C-zone (Fig 1). Ore production originally was from the A-zone open pit operation while the A-zone and B-zone underground workings were being developed. The mining method employed underground is blasthole open stoping with delayed rockfill. Mining block dimensions are nominally 20 m along strike by 25 m high. Stope extraction is sequenced to achieve a relatively short pillar life and 100010 ore recovery. Pillars are extracted as soon as the adjacent primary stopes are two cycles ahead. Primary stopes are filled with consolidated rock fill after mining. This allows pillars to be blasted right against the consolidated fill, but also requires that the fill be self supporting to a height of 30 m.The Williams mine places approximately 1.4 million tonnes of rockfill and 50 000 tonnes of binding agents each year, with about three quarters of the fill placed being consolidated. The consolidated fill placed at the Williams mine contains Portland cement and flyash as binding agents."

Jan 1, 1994

By Zhao-shu Sun, Mao-lin Li, Rui Cui

"Fankou Mine produced pyrite concentrate (PC) from the tailings by rougher and scavenger flotation before 2010, with the averaged S grade of 40.54% at recovery of 79.34%. The economic value of PC increases with its purity. When the S grade of PC feed to sulfuric acid plant is over 47%, the pyrite cinder can reach a high Fe grade of 62% which can be directly sold as iron concentrate. On this background, engineers in Fankou Mine set the PC with S grade of 47% as target.The direct way to reach that goal was to clean the rough PC Lots of cleaner flotation tests were conducted and the balanced strategy was to produce two ranks PC with the S grade of 47% and 38% at the recovery of 44.20% and 36.17%, respectively. The dual-product flowsheet was successfully industrialized in 2010. In order to further improve the quality of PC, gravity separation was introduced into the flowsheet. The numerical simulation and tests were performed to evaluate the beneficiation and classification performance of hydrocyclone as it treated the rough PC. It was shown that the underflow of hydrocyclone could addressed the S grade of 47%, and the finer size overflow could also be enriched to PC with S grade of 47% by flotation, due to the contained pyrite with well liberation. That is to say, with the ingenious addition of hydrocyclone to treat the rough PC, single PC with S grade of 47% could be achieved. The new flotation-gravity separation flowsheet was commissioned to produce the high quality PC at the end of 2013. The averaged S grade is 47.20% at recovery of 82.26% in 2014. The two steps flowsheet improvement maximizes the enterprise benefits and leads to simple utilization of Fe in pyrite in downstream industry."

Jan 1, 2016

By Guangyuan Li

A 3-D block-spring model (BSM) has been developed for simulating the behaviour of jointed rocks. The model uses a discontinuous formulation and an iterative procedure to solve the large displacements in jointed and faulted rock masses. The 3-D BSM has been used to simulate mining excavations in jointed rocks around an open pit and underground settings. The applications have demonstrated that it is a practical tool to solve complicated problems of rock mechanics in civil and mining engineering. This model has recently been modified to incorporate complex geological conditions, such as underground water flow (seepage), unstable blocks and the time-dependent behavior of backfill materials. To demonstrate the capability of the 3-D model this paper presents the fundamentals of the 3- D BSM and its application for open-pit mining. A complete computer package BSM3D has been developed based on the 3-D block-spring model. The package consists of a solving engine for numerical analysis and a Windows based processor for mesh generation and results display. The multi-functioned pre-processor provides tools and menus to help users setting up models easily and conveniently. The fully featured post-processor allows users to view the results in different windows and orientations. The graphical results include contours, vectors, animation of rock movement, and the failure state of the rock structures.

May 1, 2001

By Meimei Zhang

In the overall open pit mine planning process, mining phase design is a strategic driver in guiding and constructing the block extraction sequence and determining the annual net cash flow distribution. Mining phase design should obey some practical constraints, such as ?minimum mining width? and ?flat mining phase bottom?, to allow space for haul road development and truck and shovel access on each bench. However, these practical mining phase design requirements are not taken into account in all first-cut mining phase design methods and post-processing is always required to convert an impractical design to a practical one, resulting in a potentially significant loss of Net Present Value (NPV) relative to the first-cut impractical designs. In this paper, we present a method using a meta-heuristic algorithm ? Simulated Annealing ? to enforce those practical constraints in determining a mineable phase design whilst ensuring minimum NPV loss.

Oct 1, 2009

By K. E. Prince, S. Burling, R. J. Ring, M. K. Maley, W. R. Taylor

Vanadium occurs as a component of carnotite, which commonly occurs in calcrete type ores, and in association with uranium in some sandstone-hosted deposits. Increasing demand for vanadium, which is used in high-strength steel and Vanadium Redox Flow Batteries (VRFBs), is offering some uranium producers a potential option for by-product vanadium recovery to improve project economics at a time when uranium prices are low. This paper presents the results of recent optimisation studies on the Bigrlyi deposit for the recovery of both uranium and vanadium. The impact of carbonate leaching conditions on uranium and vanadium extraction from a range of carnotite-in-calcrete ores is also examined, with vanadium extraction limited by the proportion of non-carnotite vanadium present in the ores. The findings are particularly relevant to developing projects as results show that elevated vanadium content in ore does not necessarily equate to a high vanadium extraction in leach.

Jan 1, 2020

Cobalt mostly occurs as a minor, but valuable, constituent in most nickel and a few copper ores, however it is not generally found alone in commercially viable deposits. Its concentration and extraction are therefore intimately linked to the recovery of the primary metals and the major task for the metallurgist is to extract cobalt of commercial grade from a much larger mass of either nickel or copper and sometimes both. With a particular focus on Vale Inco?s operations, this paper provides a brief overview of the mineralogy of the main deposits being currently exploited that contain cobalt as a co or by-product. The concentration and then extraction to metal are reviewed and some advances released into the public domain are discussed.

May 1, 2009

By Olaf Andersen

Crucible melt extraction yields short metal fibers with eqivalent diameters as low as 50 µm from almost arbitrary metals and alloys. Highly porous components can be made from such fibers by suitable deposition and sintering methods. This technology is being developed at the Dresden based Department of Powder Metallurgy and Composite Materials of the Fraunhofer Institute for Manufacturing and Advanced Materials (IFAM) and has been applied to gold alloys and iron-base alloys containing small additions of precious metals. From the manufactured gold fibers, sintered structures were made for decorative applications. Additionally, it was found that due to rapid solidification during the fiber formation, precious metals can be finely dispersed in ironchromium- aluminum (FeCrAl) and FeAl20 alloys. Good catalytic activity at elevated temperatures was found in compositions containing 3 wt.-% Ce and 0.5 wt.-% Pt.

Oct 1, 2003

By H. Nouranian, M. Askari

GOLGOHAR Mining & Industrial Co., with annual production of 16 million tons, is one of the largest pelletizing and iron ore supplier in Iran that recently this year, because of using mineral processing techniques and extraction of ore body positioning between the metamorphic rocks, about 150 million tons of dry tailings has been created as a result of concentrate production. On the other hand, many environmental issues such as groundwater pollution have been developed by sulfide and silicate gangue minerals, which containing heavy metals such as mercury and arsenic. In this study, a new product with high added value has been introduced for the company by identification and extraction of industrial minerals in dry tailings. Also, by removing large masses of dry tailings, environmental pollution sources were gradually eliminated. This method can be used as a modern waste management approach in the world.

Jan 1, 2017

By Takanori Kokubo, Kenta Suzuki, Tomohiro Sasaki, Toshiya Anami

"Previous work has shown that the strengthening Al-Mn alloys with copper leads to the formation of an undesirable reduction in recrystallized grain size. In this study the mechanisms of strengthening and recrystallization behavior in a continuously cast automotive heat exchanger fin stockof Al-1.1wt%Mn-0.5wt%Fe-0.3wt%Si with a0.3wt%Cu addition were investigated. Metallurgical analysis revealed that the Cu strengthening was dominated by the formation of dispersoid particles, while solid solution strengthening decreased with the Cu additions. This result is attributed to the decrease in the amount of Mn solid solution. The post brazing recrystallized grain size was reduced compared to that not containing Cu. It is postulated that the Cu addition leads to a decrease in the amount of Mn in solid solution which leads to a finer grain size. This effect is attributed to Mn in the aluminum matrix inhibiting boundary migration but allowing other grains to grow during heat treatment. The results are rationalized based on particle stimulated nucleation (PSN), wherein dispersoid particles are more likely to become active recrystallization nuclei during the heat treatment. The increase in the number of active dispersoid particles with Cu addition is correlated to the recrystallized grain structure.INTRODUCTIONImprovements in properties such as strength, braze ability and corrosion resistance in thermal fin stock alloys are all means to gain improved efficiency in heat exchangers particularly in automotive applications. While Al-Mn alloys dominate automotive heat exchanger fin stock alloy, even small chemical compositional changes can profoundly influence these properties (Kawaharaet al., 2004; Yoshino et al., 2009). The microstructure (particularly the grain size and shape) also plays a key role in determining the product performance and hence the thermo-mechanical processing (TMP) must also be considered. The casting method (typically conventional direct chill, DC, or continuous casting) significantly influences the properties in no small part due to the very different TMP routes that are used. Continuous casting is generally favored for fin stock applications as its higher cooling rate (which can be 2 to 3 orders of magnitude higher than DC casting) leads to finer as-solidified intermetallic particles and an increase in super-saturated solid solution elements (such as Mn)that are known to improve fin stock performance such as strength, braze ability(Okiet al., 2008)."

Jan 1, 2018

By Michael J. Sapko, Ellsworth R. Spencer, Frank J. Perzak

"The fire resistance of several mine conveyor belts is evaluated using a new belt-flammability apparatus developed by the U.S. Bureau of Mines. The test apparatus, experimental details and a calculated flammability index (FI) are described.The FI values are useful for ranking the fir e resistance of mine conveyor belts. Values are determined using parameters readily measured with thermocouples, high-temperature flow probes and a methane-oxygen torch, all of which are components of the Bureau's new test apparatus. The FI varies directly with the flame-spread rate and the rate of heat release during burning and varies inversely with the critical (minimum) ignitor energy output.The fire-resistance ranking of nine different belt types using this moderately scaled apparatus is compared with available full-scale data on belt fires. This comparison shows that the ranking based on the FI is consistent with the full-scale data.IntroductionFull-scale fire hazard evaluations of mine conveyor belts are not easily related to the properties usually measured in small-scale flammability tests. The inadequacy of small-scale belt fire tests has been demonstrated in works by Mitchell, Warner and Reinke.Mitchell and Warner showed that certain neoprene (NP) and polyvinyl chloride (PVC) belts, which had been approved by the Code of Federal Regulations 30 CFR 18.65, were nevertheless capable of propagating flame over their entire length when full-scale fire conditions were simulated. Comparable results were also observed by Reinke at the Tremonia experimental mine in Dortmund, West Germany, where all belts burned in full-scale tests even though they passed the small-scale tests. Only by reducing the severity of the full-scale test could these fire-resistant belts be grouped on a pass-fail basis."

Jan 1, 1982