Search Documents

By Denilson Coutinho, Euler Soares, Paulo de Tarso, Jordana Ferreira, John R. Goode, Andreas Sprecher, Alexandre Rocha

The Serra Verde Project is located in the northern part of Goiás state, Brazil, and comprises 49 mineral claims covering an area of 69,814 ha. The Serra Verde deposit is a rare earth element (REE) enriched weathered granite comparable to the weathered granite, or ionic-clay, deposits found in southeastern China. The Mineral Reserves of the Serra Verde Project total 388 Mt (Measured and Indicated) at an average grade of 1,484 ppm of REE oxide (REO). Several hundred agitated leach and column leach tests have confirmed recovery of about 40 to 55% of the REE, except for Ce, using simple desorption techniques. Present plans call for a heap leach operation followed by precipitation of impurities and precipitation of a pure REE carbonate suitable for refining and separation. The project plan includes initial production of 5,000 t/a of REO, with a high content of heavy and critical REO, rising to 10,000 t/a of REO. This production rate will be obtained by mining of the Mineral Reserves over a 22-year mine life at an initial rate of 6 Mt/a for the first four years with the mining rate thereafter increasing as required by grade and production targets.

Jan 1, 2014

By Steven R. McCutcheon

"The Bathurst-Newcastle district, a subcircular area approximately 50 km in diameter, contains 37 massive-sulfide Zn-Pb-Cu deposits that have defined tonnages, and has 58 additional significant occurrences. The largest deposit is Brunswick No. 12, with total reserves (including past production) of 148 million tonnes grading about 12.5% combined Pb-Zn. The deposits/ occurrences are spatially associated with a felsic volcanic pile that contains a significant sedimentary component. In the vicinity of the Brunswick deposits the pile is divisible into lower and upper sequences. The lower is characterized by megacrystic rhyolite (QFAS) and coarse- to fine-grained quartz (± feldspar) wackes and/or tuffites (QAS); the upper sequence is characterized by aphyric to sparsely porphyritic rhyolites (HWR), micro-breccias, and acid hyaloclastites with interbedded dark gray sedimentary rocks. A greenish gray to dark gray siltstone (GGS) separates the two sequences and hosts the sulfide deposits. Lithogeo chemistry of least altered samples shows that the QFAS and HWR have an igneous character, whereas the QAS and GGS have a sedimentary signature. The two types can be distinguished on the basis of total alkalies (Na2 + K2O) versus SiO2/Al2O3 and Ti02 versus Fe/(Fe +Mg). Some trace elements, such as Sr and Y, also help differentiate the two types. The QFAS differs from HWR by having higher La/Yb ratios but lower Zr and Th. The Bathurst deposits do not show a close spatial association with rhyolites but rather are stratiform bodies Oacking clastic textures) within fine-grained sedimentary rocks. The scarcity of barite and other sulfates indicates that there was little mixing between the metal bearing fluids and cold seawater. High Fe/(Fe+Mg) ratios in chlorites also indicate the fluids did not contain a significant seawater component. These features and the large size of many deposits suggest that the deposits formed from metal-rich pore waters that were released catastrophicallyfrom an acquifer in the footwall stratigraphy."

Jan 1, 1992

By George Meadows

Consultation and Accommodation Introductions Consultation -Best Practices The Role of Negotiations The HVC Experience Summary / Conclusions The Challenge Meeting legal and policy obligations to consult while adhering to project priorities, timelines and budgets Defining who needs to be consulted, by whom, and ?how much?? Accommodation ?who is responsible and what is the appropriate scope? Social License -establishing positive working relationships with First Nations involved in project review / approvals / implementation in a manner that advances the interests of all parties

May 1, 2010

By G. Barrasso

REACH was proposed by the EU Commission in October 2003 and stands for the Registration Evaluation, Authorisation and Restriction of Chemicals. It requires that all substances identified as persistent, bio-accumulative and toxic, whether the risk of those chemicals being released is real or perceived, require registration prior to them being allowed to be imported into the European Union. An internal investigation by the metals industry indicates that almost all primary raw materials streams would be classified as hazardous due to the potential health or environmental hazard properties of one or more of their ingredients. REACH uses a wide definition for chemicals and metals and as such its implications greatly impact the entire supply chain of the metals industry. The process of registration would require the producer/ importer to produce a dossier. Initiatives along the same lines as the EU REACH are also coming up in other parts of the world. REACH requires registration of at least four substances manufactured by the aluminium industry: aluminium metal, including powder, aluminium oxide, and aluminium hydroxide. The proposed legislation permits the affected companies to band together to form a consortium to develop certain aspects of the registration application. The aluminium industry has established a consortium and testing is currently underway.

Jan 1, 2006

By L. Chunpongtong

ABSTRACT Oil sands production occurs on a massive scale, making orebody estimation a challenge. In rainy conditions, operators can have difficulty accessing ore at the mapped location. Without enough inventory as a buffer, the high-cost stockpile is depleted quickly, necessitating the removal of significant amounts of overburden and interburden to meet plant feed requirements. The inventory curve—a plot of ore inventory on a period-by-period basis—plays an important role in selecting an appropriate scheduling scenario. This paper presents a programmable method for creating an inventory definition by using a pit optimization tool.

Jan 1, 2014

By Jorgen Elbrond, Yve Lizotte

"A mathematical procedure for determining the underground mining level layout which minimizes the total costs of excavation and haulage is described. This procedure has the advantage over previous graphical procedures of being easily amenable to microcomputers. The paper demonstrates through examples how the procedure can be applied to minimizing discounted costs of level layout as well as providing the optimal location of a production shaft.IntroductionIn recent years there have been numerous publications in mining journals concerning the minimization of mine haulage costs. With the rapid escalation of energy costs during the last decade it is not surprising that several studies applying queuing theory, simulation and mathematical programming to mining related transportation problems have been successfully undertaken. Because of the increasing availability of various sizes of computers these techniques have gained considerable popularity as evidenced by the numerous commercial packages presently being marketed.The publications concerned with haulage cost minimization are generally concluded along the lines of ' ... haulage costs at production rate x will be minimized by assigning y units to location z...'. Details about the route followed and whether it guarantees a minimization of costs are seldom considered. Route data has to date been manually resolved and used for input to developed programs. It would appear that no program has been developed to date which simultaneously minimizes costs by both fleet assignment and routing network resolution.Another important factor in transportation problems is the investment cost associated with the routes; road construction costs or, in the case of underground levels, drift excavation costs. Except for special cases the transport network which minimizes haulage costs only will not provide a minimum excavation cost solution.Zarnbo(1) illustrates by graphical and mathematical procedures how central 'facilities' can be located to simultaneously minimize investment in the transport network and haulage costs. Unfortunately these procedures and others recently applied to mine haulage problems do not provide solutions to the generalized problem. Also because these procedures are geared to graphical solutions and hand computations whereby certain possibilities can be 'visually' eliminated, they can be tedious to program and present storage capacity constraints with current microcomputers."

Jan 1, 1985

By J. O. Marsden

Over the past eight years, Phelps Dodge (a division of Freeport-McMoRan Copper and Gold, Inc.) has developed a suite of proprietary hydrometallurgical processes for the treatment of copper concentrates as an alternative to conventional smelting and refining technology. The technical viability of two processes has been commercially demonstrated in a large scale plant at Bagdad, Arizona, designed to process approximately 52,500 metric tons per year of concentrate containing 30.5% copper. The first process utilizes high temperature (225°C) pressure leaching, followed by countercurrent solid-liquid separation, and then blending of the copper-bearing solution with low grade stockpile leach solution for subsequent treatment by SXlEW for copper recovery. The second process uses super-fine grinding, medium temperature (l60°C) pressure leaching, followed by solid-liquid separation, and treatment of high grade copper-bearing solution by direct electrowinning to recover the bulk of the copper values. The latter process will be utilized at Morenci in a commercial facility designed to treat mixed chalcopyrite-chalcocite-covellite concentrates. This facility is scheduled to start up in 2007. Other flowsheet options have been developed by Phelps Dodge for application to a variety of concentrate materials in specific situations. Examples of various flow sheet options are presented in this paper, and the advantages and disadvantages associated with each are discussed in detail.

Jan 1, 2007

By Kenneth L. Norris

Stonegate Agricom Ltd. is currently conducting exploration and development drilling of the Paris Hills Phosphate Project (Paris Hills Project) located in Bear Lake County, southeastern Idaho, 3.2 km west of the towns of Paris and Bloomington, Idaho. The project is located adjacent to a highway and 19 km by paved highway to Montpelier, Idaho where the Union Pacific Railroad system is located. Power and water are available locally. The nearest metropolitan centre is Salt Lake City, Utah approximately 225 km by road to the south-west of the property. The Paris Hills Project encompasses an area of approximately 856 hectares. Property holdings consist of three (3) patented lode mining claims and 16 contiguous fee parcels (some with federal phosphate leases). Active open pit phosphate mining operations are located in surrounding counties in south-east Idaho and are owned and operated by Agrium Inc., Monsanto Company and J.R. Simplot Company. The Paris Hills Project is located near the centre of the Western Phosphate Field which constitutes the most extensive phosphorite beds in the United States. Phosphate beds of the Western Phosphate Field occur within the Phosphoria Formation of Permian age and extend over an area of more than 350,000 km2 including extensive areas of Idaho, Utah, Wyoming and Montana. At Paris Hills the phosphate mineralized beds occur in the overturned limb and the horizontal limb of the Paris Syncline. Grades and thicknesses in both the western overturned limb and the eastern horizontal limb of the anticline are similar. The vast majority of potential mineralization occurs in the horizontal limb which underlies most of the property holdings. Mineralization in the overturned limb has a strike length of over three (3) kilometres and extends from the surface to a depth exceeding 300 m depending on location along the north-trending strike of outcrops. Depths of the horizontal limb range from surface along the north side of Bloomington Canyon to estimated depths of 915 to 1,035 m at Paris Canyon. The property contains an Inferred resource of 109.6 million tonnes at 23.6% P2O5 over two mineralized horizons. The phosphate zones have a strike length of over 3 km and extend from surface to a depth of at least 900 m. Drilling commenced late in the 3rd quarter of 2010 and is planned to continue through 2011. The drilling was planned to target an area of potentially higher grade phosphate mineralization and better define and upgrade the current resources.

May 1, 2011

By J. A. Finch

Samples of feed and product from a closed grinding circuit treating a heterogeneous lead-zinc ore were taken. The feed was subjected to laboratory batch grinding in a rod and ball mill with the objective of simulating the closed-circuit size distribution. It was concluded that the batch rod mill can closely simulate this product if only the over-all size is considered, but mineral-by-mineral large differences occur. If, as is suspected, the mineral sizes are the important factor in flotation, the differences could lead to problems in interpreting flotation results. An example of mineral recovery as a function of size is described to illustrate the potential problems.

Jan 1, 1979

By J. T. Fyles, C. G. Hewlett

"THE REEVES MACDONALD mine is in the Sa Imo-Pend d'Oreille mining area of southeastern British Columbia. It is on the Nelway-Waneta road 4 miles west of the border-crossing point of Nelway. The Reeves orebody from which all production has come is one of several mineralized zones in easterly-striking limestones occurring between the Pend d'Oreille and the lower part of Salmo River.The property was originally located as two groups of claims by R. M, Reeves and J. H. McDonald. The two groups were consolidated in 1925. and extensive development work was done from then until 1930 and again in 1937, but no ore was shipped. The mine was reopened in 1947 and, between 1949 and 1953, 1,057,804 tons of ore was mined. Concentrates recovered contained 85,626 ounces of silver, 19,394,092 pounds of lead, 72,076,495 pounds of zinc, and 455,051 pounds of cadmium. Low metal prices forced the mine to close in 1953, but operations were resumed in November, 1955.The orebodies at the Reeves MacDonald mine are steeply plunging lead and zinc sulphide replacement deposits in a banded limestone named the Reeves limestone. The orebodies contain pyrite, honey-coloured sphalerite, and galena, and are surrounded by a dolomitized zone. In the Reeves orebody, where the relationships are known, the dolomite has the same general shape as the orebody. Four zones of sulphides are known on the property (see Figure 1). Three of these, the Reeves, B. L., and O'Donnell, are believed to be faulted segments of one mineralized zone. The fourth, the Point ore zone, exposed on the north bank of the Pend d'Oreille River, is not developed and its structural position is not known, but it appears to be a separate deposit."

Jan 1, 1949

By Therese Schneck

The presence of xenon isotopes from in-situ spontaneous fission of short-lived Pu244 has been confirmed in Hadean detrital zircons from Western Australia. Hadean and meteoritic zircons can retain secondary overgrowths developed after primary cristalization at 3.97-3.94 Gyr. On the moon, the metal grain in sample 66095,78 is mantled by troilite, schreibersite and cohenite. High chlorine content FeCl2 is deposited around metallic FeNi. The magnitude of Pollonium-210 to Radon-222 on the Aristarchus plateau spectrum indicates a past greater activity. The Earth Moon system from Nb/Ta systematics is consistent with a Moon iron core delayed to 3,9 Gyr.

Aug 1, 2010

By Yuki Koshino, Kenji Kaneko, Yasuhiro Aruga, Takuya Maeda

"In general, there is a strong correlation between dislocation characteristics and mechanical properties of aluminum alloys. In this study, dislocation characteristics of tensile deformed Al-Mg alloys were examined by transmission electron microscopy. An Increase in the solute concentration, ranging between 0.3 and 1.1%, Mg leads to increase in strength and decrease in uniform elongation. The accumulation of dislocations during the tensile deformation is observed in lower strain as the concentration of solute Mg in the alloy is higher. It is believed that the solute Mg in Al-Mg alloy promotes the accumulation of dislocation during the tensile deformation resulting in the decrease in elongation.INTRODUCTION The influences of the amount of Mg concentration on the tensile properties of Al-Mg alloys has been investigated by many researchers. It has been understood that the tensile ductility of Al-Mg alloy is higher for the Al-Mg alloys with higher Mg concentration beyond 2 mass% (Mukai, Higashi, Hirano & Tanimura, 1993). Uchida and Yoshida (1995) reported the formation of microbands during the tensile deformation due to the localization of dislocations, and the amount of microbands were reduced when the Mg concentration of the Al-Mg alloy was increased from 3 to 9 mass%. Their study suggested that the dynamic recovery of dislocation was retarded due to the increase of the Mg concentration during the tensile deformation, which resulted the increase in ductility. On the other hand, in the case of Al-Mg alloys with the Mg concentration less than 3 mass%, the reason why the ductility of Al-Mg alloys decreases with increasing Mg concentration has not been sufficiently investigated. In general, the Mg concentration used for automotive usage is less than 1 mass%, in the case of Al-Mg-Si alloys (Aoki, 2013). Therefore, to clarify the roles of Mg in the low concentration range on ductility of aluminum alloys and to elucidate its mechanism contribute to alloy design of Al-Mg-Si alloys having good formability."

Jan 1, 2018

By Alexandre Desbarats, Michel David

"All optimum pit design studies start from the geological are reserves inventory, the estimated grades of all blocks of potential are within the interpreted limits of the deposit. The actual optimization procedure is then carried out on block valuations based on these estimated grades. Thus, the relevance of any pit design can be seen to depend directly on the ore reserve estimation . To insure a proper pit design, a first step would be to use a geostatistical reserve estimation technique such as kriging, however, this is not enough. A frequently neglected fact is that the blocks of ore estimated during the planning stage of the mine are usually considerably larger than those on which the ore-waste selection will be made at the time of mining. Experience in the exploitation of large low-grade deposits has shown that large blocks, estimated to be are, when mined selectively in smaller blocks, often yield significant amounts of waste material. This phenomenon, known as internal waste, is a function of the variability of the grades, the size of mining unit and the amount of sampling information on which ore-waste decisions are made.In this study, it was proposed to consider the effect of internal waste caused by selective mining, on. pit design, using geostatistical methods to predict the tonnage and grade of recoverable reserves within large blocks.Optimum pits obtained using a block valuation formula taking into account the recoverable reserves within large blocks were compared with optimum pits obtained using a conventional block valuation formula. It was found that the optimum pits obtained by the proposed method had the highest total valuations and thus were, in fact, ""more optimum”. These pits were characterized by greater are tonnages at a lower average grade, the additional ore more than compensating for the drop in grade. It was also found that the consideration of internal waste in pit design could considerably alter pit limits in marginal areas of the deposit.It was concluded that selective mining had a significant, potentially critical, impact on the design of optimum pits especially in the case of large low-grade deposits."

Jan 1, 1984

By G. Vibert Douglas

"Gold occurs in Nova Scotia in three ways, saddle reefs, fissure veins, and fossil placers. Of these the saddle reefs are the commonest. They have been the source of most of the gold and have also been the subject of most of the literature on the gold occurrences.The Meguma or Gold-bearing series of Nova Scotia is a conformable succession of quartzite's and slates, possibly Precambrian in age, which have been folded into a number of anticlines and synclines that strike (Fig. 1) roughly east and west. This folding has been termed Acadian and is probably a westward continuation of the Caledonian revolution in Britain. It may have started in the Ordovician and continued through the Silurian and into the Lower Devonian. It was followed by the intrusion of the great Devonian granite batholiths. It is thought that the mineralization is connected with the late phases of the cooling of the granite. As the name saddle reef implies, the veins form on the crests and flanks of the anticlines, possibly in the synclinal troughs as well. The beds favoured by the solutions are the slates. The reason for this is apparent when it is realized that in order to fold over 30,000 feet of sediments (the thickness of the Meguma according to E. R. Faribault) through p radians of arc it is necessary to have a differential movement between the top and bottom beds of p times the thickness of the sediments. In the case of the Gold-bearing series, in which strong quartzite beds lie between incompetent slate beds, most of this differential movement was taken up in the slates. The evidence for this is the remarkably fine drag folding and the intense shearing and comminution of some of the beds of slate (Fig. 1). The quartzites exhibit some shearing and faulting, but there is little doubt that the greater permeability lay along the incompetent slate beds. The mineralizing solutions followed these beds and also passed from one slate bed to another through a joint or fault in the intervening bed of quartzite. These joining veins are called angulars in Nova Scotia. Within the veins the gold is in shoots and the real problem is to find out what controls the position and extent of the shoots."

Jan 1, 1954

By G. W. H. Norman

Introduction During the past few years emphasis has been placed on the importance of major faults, fault zones, and associated structures in localizing ore deposition. This interest has developed partly through experience in mining camps in other parts of the world, and partly by the discovery of such structures associated with ore deposits in the Abitibi region, northwestern Quebec. The recognition of these structures has been brought about chiefly by detailed mapping that has been gradually extended along most of the southern gold belt of Quebec and across adjacent parts of Ontario. In the Chibougamau region of northern Abitibi, progress has been made in the mapping of major faults by using aeroplane photographs with a scale of about 1,000 feet to one inch for field mapping. These studies have shown that many large faults occur in the Abitibi region; also that there is a relationship, direct or indirect, between faults and mineral deposition. The faults are, however, of more than one type and age, and this should be clearly appreciated in any planned programme for prospecting this great region adequately. The information regarding faults and structure is so widely scattered that it is difficult to obtain a clear picture of the essential features, either for planned prospecting or for analysis and development of ideas for further study. This paper, as originally conceived, was intended only to discuss and compare the regional structure of southern Abitibi county-where detail mapping and diamond drilling have been carried on intensively for the past ten years-and of the less well-known Chibougamau district, in order that the experience gained in the one area could be usefully applied in the other. However, a comparison of the two districts leads naturally to a consideration of their common relationship to certain major late-Precambrian structures that form an important northeast system across the southeastern part of the Canadian Shield.

Jan 1, 1946

By M. Azzaz

In this paper, we report on new mechanical tests, at high temperatures, performed with a supposed better aluminium nitride (A1N) material, containing fewer oxygen. Our purpose was twofold: (i) check whether creep resistance is modified and hopefully enhanced and (ii) determine the elementary mechanisms controlling plastic deformation through transmission electron microscopy (TEM) observations of deformed samples up 10% strain in compression at elevated temperatures (1823-1923 K) under constant stress in the range 150¬250 MPa. Stationary rates are lower by an order magnitude than those previously measured in MN with higher oxygen content. All dislocations imaged by TEM look undissociated, which clearly relates the formerly observed wide dissociation to oxygen in excess.

Jan 1, 2004

By I. Filzwieser, M. B. Hanel, A. Filzwieser

The paper describes the current density increase within the last 150 years. From the beginning in 1885 at 30 A/m² up to the highest used current densities nowadays at 420 A/m² towards future pathways were even 1000 A/m² can be achievable. A short tour through history will highlight the milestones of the process of electrolytic refining of copper. Besides the improvement of the existing technology, the biggest changes leading to higher possible current densities are linked to the introduction of the ISA stainless steel plates and the introduction of the parallel flow principle. Furthermore, the parameters influencing the limitations regarding current density and therefore the practical used current density as well as the influence from the chemical composition of the electrolyte is discussed. Finally, the possibility of further increasing the current densities by enhancing the relative movement between electrolyte and electrode will give an outlook about the future of the copper electrolysis process. INTRODUCTION The current density is the most important characteristic to describe the productivity of a copper refining electrolysis besides the characteristic number for the electrical efficiency. Over the last 150 years, current density has risen from a few amperes per square meter to over 400 A/m² without any significant change in the principle of electrolytic refining. This increase in current density is documented exemplary by the electrolysis of Montanwerke Brixlegg in Austria (Brixlegg, 1963, 2013). The very beginning of the technology of electrolytic refining of copper was first patented in England by James Elkington in 1865 and the first electrolytic copper refinery was built in Newark, New Jersey, in 1883 (Armstrong, 1999). The secondary smelter Montanwerke Brixlegg, Austria, has been operating an electrolysis plant since 1884. In 1988, the third "Mount Isa" electrolysis plant worldwide and the first in Europe was put into operation in Brixlegg. Since 2010, the so-called high-current electrolysis (parallel flow METTOP-BRX Technology) with a current density of approx. 400 A/m² has been operated in half of the electrolysis process.

Jan 1, 2019

By H. R. Stockford

"A pyroxenite-carbonatite complex containing extensive pyrochlore mineralization was discovered during January, 1966, within an exploratory license area held by Consolidated Morrison Explorations Limited. Located 32 miles south of Moosonee, Ontario, the deposit was found under 100 feet of glacial till and Paleozoic sedimentary cover using airborne and ground magnetometer surveys. Exploratory and detailed drilling, totalling 47,625 feet in 85 holes, was completed in outlining the deposit to a maximum depth of 900 feet. Pyrochlore reserves are estimated at 62,000,000 tons averaging 0.52 per cent Cb,05 to a depth of 825 feet. Included in this tonnage is a high-grade section containing 10,000 tons per vertical foot grading 0.82 per cent Cb20 5• The deposit is still open at depth and the intrusive complex has by no means been fully explored.The columbium (niobium) mineralization occurs in a lineated calcite-dolomite host rock which has been intruded along a fault zone within a northeast-trending granulite belt. Potassium-argon dating indicates an age of 1655 million years.Preliminary studies suggest that the complex was intruded in a series of pulses in the form of a partially crystallized mush. The James Bay intrusive is unusual in that it is linear in form and contains only two main rock types - p•yroxenite and carbonatite. Nepheline-bearing syenites and associated rocks are notably absent. Moreover, the pyrochlore is essentially non-radioactive and free from many of the impurities generally associated with other pyrochlores. A test shaft to investigate soil conditions and to provide a 250-ton bulk sample was completed during 1968. Subsequent pilot-plant operations indicate that good quality pyrochlore concelttrates can be produced from this deposit."

Jan 1, 1972

By Kenneth Williamson

La découverte de nouveaux gisements métallifères constitue le point de départ du développement de l'industrie minérale. Or, au cours de ces dernières années, le nombre de ces découvertes a fortement diminué dans les territoires classiquement explorés, entraînant une recrudescence de l?exploration dans les terrains géologiques de grade métamorphique élevé (e.g., Province de Grenville, Grand Nord du Québec). Ces derniers ont été traditionnellement considérés comme stériles à cause (i) de la monotonie apparente des gneiss qui les composent, (ii) de la difficulté d?identifier leurs protolites, (iii) des changements importants dans l?apparence des gîtes recherchés reliés au fort degré de déformation et de métamorphisme et (iv) des théories qui prônent un lessivage important des cations et des métaux d?intérêt économique par les processus de déshydratation des roches lors du métamorphisme régional (Weaver et Tarney, 1985; Vokes, 2000). Cependant, l?avancée des connaissances dans la compréhension des gîtes métallifères et de leurs terrains hôtes gneissiques intensément métamorphisés, montre que les systèmes géochimiques des roches altérées demeurent robustes (p. ex. ; Trägårdh, 1991; Craig et Vokes, 1993; Geringer et al., 1994; Schandl et al., 1995; Zaleski et Peterson, 1995; Vokes, 2000; Blein et al., 2003, sous presse). Bien sûr, les sulfures peuvent être localement remobilisés et même fondre, mais cette remobilisation n?implique pas forcément la disparition du gîte hôte (Williams, 1990) et peut s?avérer, bien au contraire, bénéfique pour la rentabilité d?un gîte en augmentant sa teneur en minerais (Marshall et al., 2000). Jusqu?à présent, dans les terrains métamorphiques, les contextes sédimentaires et plutoniques ont été reconnus et respectivement explorés pour les gîtes de type SEDEX et les gîtes magmatiques de Ni-Cu. L?étude de gîtes de métaux de base et précieux intensément métamorphisés (faciès des granulites) et leur comparaison avec des gîtes équivalents peu on non métamorphisés a permis d?établir, au cours des dernières décennies, des outils pour l?exploration des terrains de haut-grade métamorphique (Vokes, 1991, 2000; Slack et al., 1993; Spry et al., 2000). Ces outils sont basés sur la reconnaissance de roches diagnostiques d?une circulation ou d?une exhalation de fluides hydrothermaux telles que les méta-exhalites (formation de fer, coticules, tourmalinites, roches riches en quartz-gahnite, en apatite, en barite ou en staurolite zincifère) (Spry, 2000; Spry et al., 2000). Ils sont utilisés constamment dans les ceintures supracrustales riches en roches métasédimentaires.

May 1, 2003

By R. Noorani, M. Cai

"Excavation of deep underground openings in highly stressed grounds can generate new fractures near the openings. As a result, rock mass bulking may occur, leading to large wall deformation. A better understanding of brittle rock failure and the associated fracturing process at the laboratory scale is an essential step towards evaluating dilation behavior of rocks. A grain-based model that can capture dilation behavior of rocks under various loading conditions at the laboratory scale can be a useful approach to study rock mass bulking at the field scale. The aim of the paper is to study the dilation behavior of rocks at the laboratory scale employing numerical simulation. A modified grain-based model is used to simulate the macroscopic response of crystalline rocks by considering micro-fractures at the grain scale. Grains generated with the Voronoi tessellation are allowed to fail in tension or in shear using a strain-softening model. Damage is represented by either grain boundary fracture or grain failure, or the combination of the two. As stress increases, the process of damage, fracture initiation and coalescence in rocks can be captured.The grain-based model was calibrated using test data of the Lac du Bonnet granite and a parametric study was conducted. Numerical simulation results showed that the proposed modeling approach is able to capture most of the mechanical properties, fracture pattern, and dilation behavior in both unconfined and confined loading conditions. In an unconfined compression test, interactions of microscopic fractures may lead to macroscopic shear or axial splitting failure depending on the chosen micromechanical parameters. Numerical experimental results show that the dilation behavior of the model is strongly related to the failure mechanism of rocks. Tensile-failure-dominated failure mode generates large dilation due to the formation of new cracks that are sub-parallel to the loading direction. On the other hand, shear-failure-dominated failure mode produces small volume increase. One significant finding from this study is that in order to capture large dilation using grain-based UDEC models, intragranular grain failure should be considered."

Jan 1, 2015