Search Documents

By E. Peek, L. Becze, K. Reading

"Gallium oxide is an important semiconductor material used in optoelectronic devices (flat panel and solar cell) catalysts and sensors. One of the methods to produce ?-Ga2O3 is the so-called hydrothermal route. It is practiced by Neo Gallium Compounds and comprises of two steps: (1) the production of mainly gallium-oxy-hydroxide in a pressure vessel by reacting metallic gallium with water at 200-220 ºC and (2) the calcination of gallium-oxy-hydroxide at 700-750 ºC to convert it into ?-Ga2O3. This paper describes this pressure hydrometallurgy process supported with relevant thermodynamic data and presents the characteristics of the ?-Ga2O3 powder produced for commercial purposes. INTRODUCTIONGallium is a relatively new metal, having been predicted by D. Mendeleev in 1871, discovered by P.E. Lecoq de Boisbaudran in 1875, and first commercially produced in the USA in 1943. Gallium is not rare, being more abundant in the earth crust than antimony, bismuth, molybdenum, silver and tungsten. However, few gallium minerals exist in nature, and the dispersion of gallium within other minerals add to the complexity of its recovery. In practice, gallium is found in dispersed state primarily in bauxites and in some sphalerites, and, to a much smaller extent, in some coals. At present, a very large proportion of the primary gallium in the world is recovered as a by-product of aluminum plants, mostly Bayer plants, where gallium is extracted from a bleed of the Bayer liquor (Roskill, 2011). In 2011, world production of primary gallium was estimated at 200 metric tonnes. In addition, there is a significant contribution of recycling to the overall yearly availability of the metal.Gallium exhibits fairly remarkable properties: it is liquid above 29.76 ºC, can be supercooled, and with its high boiling point (2204 ºC), is the metal with the widest liquid range. Gallium is magnetic, and is an excellent conductor of both heat and electricity. Gallium also displays a marked anisotropic electrical conductivity (Roskill, 2011). All these properties render gallium almost irreplaceable in the semiconductors (GaAs, GaN, GaSb, GaP wafers) and the optoelectronics industry (flat panel, solar cell)."

Jan 1, 2012

By K. J. Daun, C. J. Shi

UsiborThrough the second step heating at 900 °C, the spectral emissivity shows a gradually decreasing trend with increasing soak time, caused by the surface phase transformation from Al® 1500P coupons are austenitized in a Gleeble 3500 thermomechanical simulator using a two-step heating procedure in an argon atmosphere. Variations in spectral emissivity are measured in-situ using a near infrared spectrometer and ex-situ with a Fourier transform infrared reflectometer. Microstructural evolution and surface roughness are investigated using optical microscopy, FE-scanning electron microscopy, and a surface profilometer. A series of phase transformations of Al-Fe-Si intermetallic phases at the coating/steel substrate interface cause the surface phase and surface roughness to change, which in turn influences the spectral emissivity. At the beginning of the first heating step, the coupons have very low spectral emissivity, due to the molten Al-Si coating. Spectral emissivity increases significantly with increasing soak time from 5 to 12 minutes, associated with the surface phase transformation of the coating into Al7Fe2Si intermetallic phase and an increase in surface roughness. 5Fe2 into AlFe intermetallic phase with a decrease in surface roughness.

Jan 1, 2015

By W. Curlook, V. G. Papangelakis, M. Baghalha

A pressure acid leaching process has been developed for the extraction of metal values, nickel, copper, cobalt and zinc, from base metal smelter slags. The basic concept contemplates cooling the smelter slags through solidification sufficiently slowly to induce a good measure of crystallization; and subsequently, after fine grinding, to pressure leach such slags at around 250°C while applying oxygen overpressure, utilizing smelter byproduct sulphuric acid. High levels of extraction of the slags' metal values are thereby achieved. It has been shown that if the same slags are quenched thereby producing an amorphous structure, the resulting metal extractions are very low. The process is applicable to smelting furnace throwaway/discard/dump slags, as well as to in-process converter slags. By extracting the bulk of the residual base metal values in the throwaway/discard/dump slags, the resulting leached residues are rendered virtually benign vis-à-vis the external environment.

Jan 1, 2004

By D. M. Aloi

In today's evolving and globalized world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to "engage" with communities and measure the success of these engagements without a clear understanding of "how" to do this. This move, away from "Corporate" Social Responsibility (CSR) and compliance, develops more of a focus on "Community" Social Responsibility and sustainability. This shift in focus leads to the development of world-class projects that provide sustainable development for people, reduces the incidence of costly delays, and promotes good global citizenship for corporations. The process of "engaging" communities in mining project design and development leads to a stronger license to operate and sustainable development. To create this mutually beneficial relationship between communities and companies, communities must be "engaged" in the mining process as early as possible, preferably during the exploration or the concept phases. How to create this "engagement" remains elusive. How to measure the progress of this engagement is also problematic. The quantitative and qualitative metrics needed to measure both positive and negative impacts of the mining and community relationship will be discussed.

Jan 1, 2007

By S. Khallouk, J. Zollinger, J. R. Kennedy, E. Bouzy, B. Rouat, D. Daloz

Titanium aluminides recently replaced Ni-based superalloys as turbine blades in the last LP stage of aircraft engines. To extend their range of use at higher temperature their properties need to be improved, either by alloying or processing. An efficient solution is to reduce the grain size during the solidification process. In the first part of the paper, an overview is given on the possibilities for grain refinement of such alloys, based on literature data and new results. The most efficient grain refinement is obtained with boron addition which leads to boride formations that are detrimental for in-use properties of turbine blades. In this work, the use of the high grain refinement potency of inoculation with non-brittle particles has been used by developing new refractory-based inoculants. The effect of one of these inoculants on grain refinement of an as-cast structure in a Ti-46Al is presented; resulting in a reduction of the grain size by a factor of 3.While less efficient compared to the potency of boron containing alloys, the grain refinement is effective and does not introduce any embrittling particles.

Jan 1, 2015

By G. Titichoca

Modification of the blasting process considers that any increase in the energy consumption generates greater benefits if done in the later stages (associated with a larger decrease in energy consumption). Therefore, although the blasting cost is doubled, generating a greater proportion of fines in addition to a weaker ore (because with greater loads and appropriate distribution of explosives a greater number of internal cracks is generated), the reduction of the unit cost that occurs in the grinding stages (SAG and ball mills) generates a positive balance in the overall size reduction process. Codelco Chile, Division Andina, has developed an extensive experimental plan to evaluate the concept of blasting modification applying greater energy. This was implemented in two stages, each including a specific mine sector: La Union and Don Luis. This paper reviews the experience of implementing such blasting modifications at the La Union mine and its impact on the design concepts and the operation of the SAG mill plant

Jan 1, 2007

By R. Kamguem

The surface of a mechanical part plays an important role in determining performance in service. The presence of scratches left by the cutting or tearing of the material on the surface of the workpiece supports the concentration of stress and strain. This article presents the experimental study for high speed milling of the aluminum alloy 7075-T6, using cutting tools different by the nose radius and coatings (TiCN, TiAIN, TiCN + A12O3 + TiN). A multi levels factorial design of experiment (DOE) and statistical analysis was used. The roughness parameters investigated are Ra, Ra, Rv, Rc, Rsm, and Rk. The results show that the feed rate, the types of coatings and the geometry of the cutting tools have the most significant impact on the surface roughness profil. Surface finish charts according to feeds and cutting speeds were established for each tool tested.

Jan 1, 2011

By Al Holmes

"In a recent survey of Canadian work values, 89% of the men surveyed and 97% of the women surveyed described the work in a mine as ""not at all auraetive"", Work in a mine, in fact, was rated by both sexes as the least attractive of all of the types of work surveyed. Confronted with this prevailing attitude, Canada's mining industry starts out with two strikes against it in its bid to attract and hold on to its fair share of available work force.Behavioural scientists have, for decades, been seeking answers to the questions:• ""Why do people work?""• ""Why do people choose a particular occupation?""• ""Why do people choose a particular organization?""• ""Why do people leave one organization for another?""• ""Why do some people stay in an organization?""• ""Why do some people work harder than others?""Their answers to these questions, although tentative and often contradictory, are being used by more and more organizations to solve people problems. Few industries can afford to ignore them, least of all, perhaps, the mining industry.Consider the following developments:I. General Motors and the United Auto Workers turn around the car assembly plant in Tarrytown, New York in seven years from the plant with the poorest labour relations and production record to one of the best under a program referred to as ""improving the quality of work life.""2. Shell Canada and the Oil, Chemical and Atomic Workers have designed a new petro-chemical processing plant in Sarnia using a set of principles that seek to optimize both the social and the technical system."

Jan 1, 1980

By G. Pouskouleli, T. A. Wheat

"The role and benefits of using statistical methodology in the development and optimization of materials and processes is examined. It is shown that considerable benefits accrue from the use of an appropriate design in which a number of factors (process parameters) are varied simultaneously while the system response such as percent recovery, degree of separation, purity, etc. is monitored and ultimately optimized.Compared with the commonly encountered one-factor-at-a time approach, this schema exploits reduced experimentation (thereby requiring reduced resources [staff, time, dollars, etc.]) yet yields quantitative information on the significance of each factor and their combinations on the measured response."

Jan 1, 1992

By Mark Weidenbach

OZ Minerals owns and operates the Prominent Hill copper-gold concentrator in South Australia, built in 2008 and commissioned in early 2009. The concentrator operates via semi autogenous grinding in a thirty four foot ThyssenKrupp Polysius mill followed by a twenty four foot Polysius ball mill in closed circuit with hydro cyclones, designed for an ore throughput of eight million tonnes per annum. The main aspects of designing the circuit are discussed along with the issues faced in the early stages of operation. A review of the optimization strategy applied to the milling circuit such as cyclone optimization, advanced process control strategy implementation and reline management to improve availability is then discussed highlighting areas of significant process improvement that have seen the plant exceed nameplate throughputs above nine million tonnes per annum.

Jan 1, 2012

By M. Bustin, A. Hosseinian, G. Preisig

Hydraulic fracturing and hydraulic shearing techniques are essential for the development of unconventional oil & gas and geothermal resources. Such techniques will also play a key role in the development of CO2 sequestration, and management of high stresses encountered with deep mining. However, the optimal design of hydraulic injections is often limited by continuum treatments of the rock mass without consideration of the influence of the natural fractures present. These may interact with the hydraulic fracture to promote offsets or arrest, or may cause the natural fractures to undergo shear and dilation. Given the limited access to the rock afforded by deep boreholes common to oil & gas and geothermal projects, advanced numerical modeling is critical for understanding key mechanisms and interactions. In this work, we first present a coupled hydromechanical distinct-element model focusing on the propagation of a hydraulic fracture. Normal and shear displacements arising from the generated hydraulic fractures are subsequently integrated into a fracture flow model for detailed analysis of specific flow behaviour and fracture permeability. For this, a scanned 3-D profile of a natural fracture is used to correlate surface roughness to dilation as a function of shearing. Fracture flow is computed at different time steps corresponding to different fracture propagation states and geometries. Modeling results indicate that the opening of a tensile hydraulic fracture is accompanied by millimetre-scale shear displacements associated with slip and wedging between adjacent blocks. This may leads to a mismatch between the upper and lower walls of the fracture if asperities are irregular and strong enough. However, fluid-induced tensile fractures have low Joint Roughness Coefficients (JRC), and associated millimetre-scale shear displacements are too small to ensure a significant offset of asperities that prevent a fully-elastic closure when the hydraulic fracture is depressurized. Injection of proppant is thus critical to keeping hydraulic fracture apertures open. Future work is planned that will see the models calibrated against field data including microseismic event locations, magnitudes and source mechanisms, tiltmeter deformations, stress change, and pore pressures.

Jan 1, 2015

By A. Azizi, P. Blatter, A. Bouajila

ABSTRACT In-situ monitoring of gold dissolution by means of a rotating electrochemical quartzcrystal microbalance unveiled dramatic decreases in gold leaching from sulphide-rich ore after 360 minutes in an actual cyanidation circuit. Pre-oxidation was effective in enhancing gold extraction by preventing a passive film from forming on gold surfaces. This work aims to highlight efforts undertaken to determine (1) how gold cyanidation is limited by passivation, (2) what reactions and mechanisms are involved during sulphide-rich ore cyanidation, and (3) how peroxidation efficiency of an industrial sulphide ore is controlled by galvanic associations between its sulphide constituents.

Jan 1, 2013

By J. Guha, D. Racicot, S. Peloquin, F. Lange-Brard, S. Bureau, A. Tremblay

The Devlin copper deposit consists of a flat-lying vein and a network of steeply dipping mineralized veinlets hosted by leucotonalite of the Chibougamau Pluton. Most of the vein is enclosed in a hydrothermal breccia zone which has been superimposed on a primary igneous breccia formed during the emplacement of the leucotonalite unit. This igneous breccia contains cognate fragments as well as fragments of the Dore Lake Complex, host rock to the pluton, set in a leucotonalite matrix. The hydrothermal breccia is formed of fragments of leucotonalite and the earlier breccia set in a matrix of finely comminuted rock variously altered in a roughly zonal arrangement. The major ore-bearing structure is the tabular flat-lying vein, varying in thickness from 10 centimetres to 1 metre, with a slight dip to the northeast. Well developed fracture planes, in four major orientations, contain both sulphides and gangue minerals. These appear to be displaced by the flat-lying vein. Late movements affecting the deposit include minor vertical displacements and an east-west shear truncating the southern edge of the vein. Widespread selective alteration of the leucotonalite, followed by multiple alteration veining stages characterize the deposit. Fluid inclusions associated with the mineralization indicate low temperatures, variable salinities with a variety of daughter minerals, and a vapour dominated phase. The fluid shows evidences of boiling at shallow depths. The sequence of events envisaged for the Devlin deposit is a primary brecciation during emplacement of the leucotonalite unit with widespread selective alteration possibly during the cooling stages followed by hydrothermal brecciation and late stage fract uring producing the vertical fractures and the flat-lying vein. From the alteration characteristics and the fluid data it is inferred that the Devlin deposit is the near-surface expression of a porphyry system.

Jan 1, 1984

By R. Carter, C. S. Samis

"SummaryThe results of this investigation indicate that the gold in the cyanide tailing of refractory gold cyanides is occluded in fused •particles formed during roasting. This conclusion was reached following microscopic examination of calcines produced at various furnace temperatures with different atmospheres, and a •comparison with calcines produced by decomposing samples of completely sulphated concentrate under conditions such that the maximum particle temperature varied between 6•50°C. and 1,100°C. This comparison showed that the particle temperature during a normal roast may be several hundred degrees higher than the furnace atmosphere, or that the fusion is associated with a low melting (950°C.) eutectic mixture of FeO and FeS.Because of the unavoidable particle fusion during a furnace roast, and because low particle temperatures are essential for gold extraction by cyanidation, aqueous medium oxidation under high oxygen pressures was studied. Gold recovery from calcines produced by this means was over 98 •per cent •compared with a maximum of 80 per cent from furnace calcines.IntroductionMANY arsenical gold ores are called 'refractory' because much ' of the gold cannot be satisfactorily extracted by cyaniding the raw ore or concentrate. Even when such ores are roasted to oxidize .the iron and arsenic and 'release' the gold, often 10 to 25 per cent of the gold present is lost in the cyanide residues."

Jan 1, 1952

By Robert D. McKellar, Luke Frawley, Okrasa. Richard

"The resource industries in Canada are facing increasing global competition and stringent environmental regulations. This has made it essential for companies to lower operating costs wherever possible. Electrical energy rep-resents one variable cost that may be better managed and utilized, providing the user with lower operating costs, improved productivity and better yields.The utility industry is also facing changes in the way it must do business. Utilities in North America are facing the prospect of deregulation that will eliminate the monopoly they have traditionally held. This will force them to strive for lower operating costs, to maintain a competitive position and to improve customer ser-vice so as to maintain their customer base.Ontario Hydro has been working with industry for several years. Many opportunities for cost savings have been identified involving energy efficiency, process improvements and the use of new electro technologies. One useful service that the utility can offer industry is to increase the awareness of potential opportunities suited to their operations. This paper will provide an overview of some of the projects that have been implemented and those that are presently being evaluated. An electronic data-base of electro technology applications that is under development will also be described."

Jan 1, 1996

By Robert D. McKellar, Luke Frawley, Richard Okrasa

"The resource industries in Canada are facing increasing global competition and stringent environmental regulations. This has made it essential for companies to lower operating costs wherever possible. Electrical energy rep-resents one variable cost that may be better managed and utilized, providing the user with lower operating costs, improved productivity and better yields.The utility industry is also facing changes in the way it must do business. Utilities in North America are facing the prospect of deregulation that will eliminate the monopoly they have traditionally held. This will force them to strive for lower operating costs, to maintain a competitive position and to improve customer ser-vice so as to maintain their customer base.Ontario Hydro has been working with industry for several years. Many opportunities for cost savings have been identified involving energy efficiency, process improvements and the use of new electro technologies. One useful service that the utility can offer industry is to increase the awareness of potential opportunities suited to their operations. This paper will provide an overview of some of the projects that have been implemented and those that are presently being evaluated. An electronic data-base of electro technology applications that is under development will also be described."

Jan 1, 1996

By N. Ginouse, S. Reny

"In the mining industry time is critical as production depends on the speed of the mining cycle. During the mining process, the time required to re-open access for the next phase of an underground heading is a key point that strongly depends on the ability of the selected ground support technique to promptly ensure the safety of workers. Fiber reinforced dry-mix shotcrete has been proven to be an efficient and well adapted technique, able to produce a ground support material with the required energy absorption or flexural toughness in a single application phase. In this context, this paper demonstrates the possibility of significantly speeding up the mining process by using a new fiber reinforced dry-mix shotcrete. The new fiber reinforced dry-mix shotcrete is capable of developing flexural toughness in only 24 hours that is equivalent to what is typically achieved after 28 days using current fiber reinforced drymix shotcrete technology.INTRODUCTIONShotcrete is often used for ground support when using the drill and blast method or other tunnelling methods. But before re-opening access for the next phase of the underground heading, the applied shotcrete is required to reach a minimum compressive strength and in case of fiber reinforced shotcrete, a minimum flexural toughness (energy absorption) in order to ensure the safety of the workers going into the heading. Combined with bolts, the use of conventional fiber reinforced shotcrete becomes an interesting method for ground support as it is applied very soon after excavation and works to stabilize ground movements (Bernard E. S., 2009). In this case, the toughness development of fiber reinforced shotcrete becomes an important feature of the material when looking to speedup the mining cycle. However, early re-entry criteria in underground openings are difficult to ascertain as the load carrying capacity of fiber reinforced shotcrete is usually assessed after 7 or 28 days. For this reason, re-entry criteria varies from one mining area to another and are usually based on compressive strength requirements. For example, in northern Ontario, Canada, one of the current practices in the mining industry consists of allowing safe re-entry once fiber reinforced shotcrete has developed a compressive strength of higher than 4 MPa (Dufour, O’Donnell, & Ballou, 2003). Flexural toughness requirements on fiber reinforced shotcrete are also typically based on evaluation after 28 days."

Jan 1, 2015

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Preg-robbing may arise from natural carbonaceous materials in the ore. Several mechanisms have been proposed in the past decades including a physical sorption process by the carbonaceous matter, or via the reduction of aurocyanide at the mineral surface (Abotsi & Osseoasare, 1986; Afenya, Osseoasare, & Abotsi, 1983; Tan, Feng, Lukey, & Van Deventer, 2005). Nevertheless, the mechanisms of preg-robbing remain poorly understood. Understanding the nature of the preg-robber is of practical importance for the selection of a suitable treatment process. Fine carbon particles in the ore have been recognized as preg-robbers due to their similarity to the activated carbon used in the carbon in leach (CIL) or carbon in pulp (CIP) processes. Previous research has illustrated that the activated carbon (also referred to as amorphous carbon in some literature) has a much higher absorption ability than pure graphite with high crystallinity (Adams & Burger, 1998). Adams et al (Adams, Swaney, Friedl & Wagner 1996) concluded that carbonaceous matter is largely responsible for the overall preg-robbing capacity of a given ore. However, the mechanism of carbon preg-robbing was still not clear mostly due to the complexity of amorphous carbon and its behavior in different solution matrices, and at different pH and temperature (Adams, 1990, 1993)."

Jan 1, 2017

By B. Qiu

The large surface ground movements induced by underground mining could threaten the safety of the pipelines laid across the subsidence-prone area. Existing analytical methods for the stress analysis of buried pipeline over mine subsidence area were based on the assumption of ?thin? pipeline, which limited their applicability. This paper presents the improved model with the capability to determine the stress distribution of the ?thick? pipeline. The pipe-soil interaction in this model was also updated to adapt various pipe soil contact conditions. In addition, the time-dependent effects of dynamic subsidence effects were also added to the model. A case of protecting a long section of a buried large-diameter pipeline over two longwall panels in a shallow mine is shown. The stress distribution along the pipeline is determined and the overstressed sections are identified. A partial uncovering plan was developed based on the predicted stress and complicated terrain at the site.

Aug 1, 2013

By Yoginder P. Chugh

This paper discusses an ongoing field study in southern Illinois (USA) that focuses on: 1) Identifying mechanisms of instability in the set-up rooms (SR) and their T-junctions with headgate and tailgate entries, 2) Developing alternate 3-entry and 4-entry set-up rooms geometry using 3-D numerical analyses, 3) Implementing developed geometries in cooperation with mining professionals and regulatory agencies, and 4) Demonstrating performance of implemented geometries through field monitoring. Illinois longwall mining operations typically experience ground control problems (roof falls, rib sloughing, floor heave, etc.) within SR layouts and around the T-junctions of SR. These occur around the areas where the SR for adjacent longwall face (to be mined) connect with the SR of the previously mined face, and around the tail-gate entries of the mined-out longwall face and around the T-junctions of SR. The problems manifest as highly fractured immediate roof strata, major shear zones in the roof, horizontal displacements within the excavations that result in shearing off the heads of the bolts, floor heave and severe rib sloughing. Similar observations have also been made in longwall mining in Utah.

Aug 1, 2013