Search Documents

By D. Mas Ivars, K. Suzuki, J. A. Vallejos

"A comprehensive geotechnical characterization has been undertaken at the El Teniente mine to describe and determine the rock mass behaviour strength properties of the primary copper ore. The Synthetic Rock Mass (SRM) modelling approach is used to simulate the mechanical behaviour of this heavily and unfractured rock mass. The micro-parameters of the model have been calibrated against mechanical properties and scaling laws for intact rock and veins, in order to represent virtual samples of four different geotechnical units. Results can be used to predict the rock mass scale effects, anisotropy, and brittleness properties that cannot be obtained using empirical methods.INTRODUCTIONThe primary copper ore at the El Teniente mine is described as very competent and massive, given that it exhibits a brittle behaviour (Rojas, Cavieres, Dunlop, & Gaete, 2000). This description is coherent with the geological description of the rock mass, which does not have discontinuities match as the definition provided by International Society of Rock Mechanics (ISRM, 1981). Only faults can be classified as discontinuities, but they are widely spaced. The primary copper ore has a high frequency of veins, where the cooper mineralization is hosted, these vein network structures are known as stockwork. Soft veins containing weak minerals as infill (chalcopyrite and anhydrite) control the disassembling of the rock mass during caving (Brzovic & Villaescusa, 2007).Presently, there are mainly two traditional methods used to estimate the strength of the rock mass: 1) determination of the strength envelope of the rock mass using scaling parameters from laboratory tests and 2) using numerical modelling based on back analysis of previous experiences of failure observed and measured in mining or civil excavations. The primary copper ore of El Teniente mine has no fractures; therefore, it is difficult to determine a rating that would enable to scale laboratory data, such as, RMR (Laubscher, 1977) or GSI (Hoek, 1994). This is the reason why the first option is not valid unless the entry data is manipulated or adjusted in order to obtain reasonable results. The second option requires, in general, a good characterization of a previous failure event in the rock mass, which is not always available. In recent years, new techniques of numerical modeling have been developed (PFC3D, ELFEN, Abaqus). Those methodologies are the third way to estimate the strength of the rock mass, but they are still in development. Particularly, the concept of SRM developed by Itasca is implemented in this study (Pierce, Mas Ivars, Cundall, & Potyondy, 2007; Mas Ivars et al., 2011), aiming to capture the real behaviour of the rock mass."

Jan 1, 2015

By M. J. Scoble, H. L. Francis, D. F. Salter, G. R. Baiden

Intelligent ore delineation refers to the ability reliably to characterize the geological setting of a mineralized body and its grade distribution. This necessitates using all available geological information in a timely and efficient manner, such that effective geological control is achieved. The importance of geological control is paramount to improving the efficiency and competitiveness of underground mines. As a result, the development of new geosensing tools designed to provide more reliable and timely information should be a priority. However, as the sensing tools advance then so, too, must the decision support system in order to allow the full benefits of these tools to be achieved. One potential system considered able to provide this architecture is ’true 3D-GIS’ (Geographical Information System). GIS promises to provide a seamless data flow and to connect information currently unavailable to the underground mine operations by bringing together previously disparate and spatial data sets in a visually effective and timely way. This paper considers the potential revolution GIS offers over the flow and use of data in mining by focusing on the integration of geosensing data and GIS to facilitate intelligent ore delineation.

Jan 1, 2000

By D. K. Fountain

"High metal prices and advanced technology in open-pit mining methods have resulted in considerable interest in the development of large, low-grade mineral deposits. Brenda Mines Limited is presently testing such a deposit of copper-molybdenum mineralization near Penticton, British Columbia.The mineralization of economic interest at Brenda has a total metallic sulphide content of between 1 and 1.5 per cent. This sulphide content approaches the limits of detectability of standard geophysical methods. How-ever, due to a favourable geological environment, it has been possible to utilize the Induced Polarization Method to outline the mineralization at the Brenda property."

Jan 1, 1968

By A. M. Ramadan

The composition of phosphate rocks, mainly used in manufacturing fertilizers, varies among deposits; therefore, phosphate rocks from different sources are expected to behave differently in acidulation processes. This paper examines the effect of preconcentration of phosphate ore from El-Sebaiya East, Egypt, using flotation on uranium leaching. A high-grade ore sample (27.3% P2O5, 168 mg/kg U) supplied by the Al-Nasr Mining Company, was subjected to reverse single-stage flotation to separate carbonate from the phosphate sample. Subsequently, P2O5 and U concentrations were 32.2% (92.1% recovery) and 225 mg/kg, respectively. After the leach process, the U concentration in the liquor was 319 mg/L.

Jan 1, 2014

By Edgar Stansfield

Introduction First, I should define more closely the vague term 'recent work' that appears in the title of this paper. Following the period of depression that was an aftermath of the first Great War, the Research Council of, Alberta carried on for ten years without a Council and without a financial yote by the Legislature. In November, 1942, a new Council was formed, under the chairmanship of the Hon. N. E. Tanner, Minister of Lands and Mines, and a vote was granted by the Legislature early in 1943. By 'recent work', I mean work during the present regime. The Council is now going full steam ahead, or would be if it could get suitable technical assistance and required apparatus and materials. Lack of these has so far made unnecessary my responsibility for seeing that we do not exceed our estimates. The Annual Meeting of the Research Council will be held in November (1945), and at that meeting the programme of work for next year will be discussed. The present time is therefore the correct time for any of you who may have ideas as to work which might profitably be undertaken by the Council, to submit these ideas for consideration. I propose to discuss my subject under several headings, and to give enough of these to show that the Council has wide interests.

Jan 1, 1946

By R. Baker

A novel electrochemical half-cell and corresponding working electrode were designed to evaluate the electro-catalytic activities of catalysts in an environment close to that of an operating proton exchange or polymer electrolyte fuel cell (PEMFC). Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques were employed using the novel cell to characterize various methanol electro-oxidation parameters that contribute to the overall reaction on a fuel cell anode. The effect of temperature on methanol oxidation kinetics was examined in the potential range of 0.31 to 0.65V (vs. NHE). The data was collected in the temperature range of 20 to 80°C. Based on the experimental analysis and literature data, an equivalent circuit model (ECM) for methanol oxidation was proposed and was used to fit the EIS experimental data. The experimental data and ECM electrochemical data was used to extract electrochemical kinetic parameters for methanol oxidation such as the exchange current density, Tafel slope, and energy of activation for the reaction. Kinetic data, especially at different temperatures, is very limited in the literature.

Jan 1, 2005

By Ahmad Ghahreman, James McNeice

"Cerium is the most abundant rare earth metal and is often found in deposits along with small amounts of more valuable metals such as neodymium and gadolinium1. As a result, the production of cerium oxide often exceeds market demands, thus in some cases it would make more sense to remove the cerium from the process solutions before further purification. A common method of cerium removal is to precipitate CeO2 from the acidic leach liquors by raising the pH to oxidize cerium(III) to cerium(IV). This study investigates the oxidation kinetics using three oxidants; hydrogen peroxide, sodium hypochlorite, and potassium permanganate. The effect of oxidant, pH, cerium concentration and temperature on the oxidation kinetics will be discussed. Cerium oxidation in solutions with pH ranging from 1.0 to 4.0 was investigated at cerium concentrations ranging from 2.0 g/L to 16.0 g/L. A cerium recovery of 40% can be achieved at different conditions with each oxidant at room temperature, with higher recovery at 60°C.INTRODUCTION Over the last 70 years, the rare earth elements (REE) have become crucial components of modern technology. These metals are categorized as light rare earths (LREE) or heavy rare earths (HREE) by governments and miners based on weight, abundance, and therefore value. The minerals bastnaesite, monazite, and xenotime compose the majority of the world?s exploitable sources of these metals (Binnemans, 2013; Parker and Baroch, 1971). Geologists classify the LREE ores as „cerium group? minerals, approximately 50% cerium oxide by weight. The cerium group minerals monazite and bastnaesite compose the majority of world production, leading to an overproduction of cerium relative to world demand. This ratio of light to heavy REE in deposits has led to a phenomenon referred to as the balance problem (Binnemans et al., 2013). As an example, to produce 1 tonne of europium oxide from a bastnaesite deposit 450 tonnes of cerium oxide must be processed. This means that any push to increase production and access the value of the HREE metals will drive down the value of the LREE metals leading to diminishing returns (Zepf, 2016). These ores also contain measurable levels of thorium, subjecting them to complex radioactive waste regulations. During the 20th century, the USA was the largest producer of rare earth metals (REMs), primarily sourced from the Mountain Pass mine in California. However, due to a combination of market dynamics and regulations, China has dominated the market for the last two decades. The largest Chinese REE mine, Bayan Obo, produces rare earth (RE) concentrate as a byproduct of iron mining, decreasing their relative production costs (Gupta and Krishnamurthy, 2005). This mine alone represents about half of world bastnaesite production (Zhi and Yang, 2014). Rising demand for high-tech products has forced Chinese producers to commission other large mines, climbing to 90% of world production in the early years of the new millennium (Mancheri, 2016). This presents the west with a looming supply risk of these critical metals in the future."

Jan 1, 2017

We report the studies of Proton-Exchange Membrane Fuel Cells (PEM FC) and hydrogen storage materials at McMaster University for the last 14 years. From the initial investigation of ionic conduction mechanism to the revelation of the origin of non-Arrhenius temperature dependence, as well as the synthesis and characterization of high temperature polymer electrolytes, both experimental and theoretical works have been compiled for the fuel cell membranes. In addition to the discovery of suppressed ionic conduction in Electrode-Membrane Assembly (EMA) and novel hydrocarbon PEMs based on micro-emulsion, the first evidence of hydrogen adsorption saturation by carbon nano-tubes was also achieved, which has been the bottleneck for the application of PEM FC. Prior to our study, a number of controversial publications have claimed the hydrogen capacity of these materials to be between 0.1 to 10.0 wt.%, and none demonstrated a plateau of adsorption with pressure that is consistent with monolayer saturation. Others suggested that the tube bundle structure is opened under high pressure to enable higher adsorption on newly uncovered surfaces, but received no confirmation. Using our home made high-pressure instrument with in-situ electrical probes, we found that a plateau is nearly achieved at about 300 atm in the room temperature isotherm, and that nanotube bundles actually compress with pressure instead of splitting, using in-situ electrical measurements.

Jan 1, 2005

By R. Walker

This paper deals with the selection and design of a belt conveyor handling steam coal between a mine and a barge loading terminal, and extending for some 5 ¼ miles over some of the most rugged terrain in the state of West Virginia, U.S.A. After a thorough analysis by consulting engineers and the owner's engineers, a single-flight cablebelt conveyor was chosen as representing the alternative of greatest reliability and lowest over-all cost. The value analysis and design features of the system are covered in this paper along with an updated report on the performance of the system since its start-up in the spring of 1969.

Jan 1, 1971

By M. S. Badollet, W. C. Streib

"AbstractA commercial method .has been developed for controlling the texture of chrysotile asbestos fibers so that they may possess properties comparable with natural sem1-harsh fibers for use in wet •processes.The physical properties of the soft, silky and slimy fibers are partially altered by a flash-heating process which removes a portion of the molecular water.The heat-treated fibers show an improvement in filterability, an increase in bulk, absorption, and surface area and better electrical properties, such as volume resistivity.IntroductionCHRYSOTILE ASBESTOS fibers are found in nature having varying degrees of texture, referred to as soft, semi-harsh, and harsh. Fibers of each type of texture have inherent characteristics which directly affect their usefulness to industry. Visual differences are apparent under a microscope where it is seen that the soft-textured fibers have a silky, serpentine or wavy appearance, whereas the harsh-textured fibers are coarser and spicular. Semi-harsh fibers, of course, have properties intermediate between these extremes.Fankuchen and Schneider ( l) have shown by the use of low-angle X-ray scattering that the diameter of the harsh type of chrysotile fiber is somewhat greater than tha of the soft variety. Surface area measurements on various chrysotiles of different textures tend to confirm their findings. By nitrogen adsorption methods, it was found that the surface areas of soft types of chrysotile asbestos are approximately 23M2 / g whereas for the harsh types they are as low as 11M2/g."

Jan 1, 1955

By P. W. Billwiller

Abstract The Britannia Mining and Smelting Company, Limited, have replaced diamond drills with percussion drills and tungsten: carbide bits for most of their blast hole drilling operations and have thereby reduced ore breaking costs. Two-inch Carset bits .are used, with one-inch hexagonal Atlas Chippewa alloy steel in 3-foot .and 6-foot lengths. Locally made couplings of Atlas SPS 245 alloy steel connect the rods. The machines used are 31½-inch automatic leyners with lugged or anvil block chucks. For drilling holes below the horizontal, the lugged machines with special adapter rods made from 114- inch solid round Atlas SPS 245 are required. These rods are lugged at one end and a water hole is drilled for six inches into the other end. Over this rod is placed a water swivel which permits the water or air to be sent directly into the steel. A decreased cost per foot, increased footage per shift, and the use of standard equipment and crews are some of the main advantages of tungsten carbide drilling over diamond drilling. Introduction Long-hole drilling with percussion drills and sectional steel was introduced in several American mines some twenty-five years ago. It did not prove very successful, however, because the rapid gauge loss in steel bits necessitated the use of very large starter bits. This in turn rapidly fatigued the straight carbon-steel then in use, made it difficult to maintain the couplings, and resulted in a slow drilling rate. The introduction of the tungsten carbide insert bit and alloy drill still has changed this picture and opened real possibilities for the application of percussion drills to blast-hole drilling. If this type of bit had been perfected ten years ago, much of the research work and experimenting done to apply diamond drills to ore breaking would have gone toward developing the application of the tungsten carbide bit to this problem.

Jan 1, 1950

By K. Howard Poulsen

Shear zones are tabular tructures which tend to occur either discordantly within, or concordantly along the margins of, competent rock masse uch as plutons, sill or flows. They contain deformed equivalents of their host rock and are common sites for gold mineralization localized in tructure oriented y tematically relative to the shear zones and internal linear fabric. Apan from genetic implications, hear zone analysis proves useful in exploration for this type of deposit because the zones are generally wider and more continuous than associated mineralization and because there is an element of predictability to mineralization geometry (i.e. vein orientation. plunge).

Jan 1, 1986

By R. D. White

"The Cumberland Basin of Nova Scotia has long been considered a structural basin by virtue of the elliptical outcrop and inward dip pattern of the Pennsylvanian outcrops. Recent published and unpublished data indicate that subsidence began in the late Devonian, perhaps resulting from a graben or rift. The Mississippian sediments which filled the growing depression were continental, lacustrine and marine with evaporites. The cessation of the riftforming processes is recorded by the alluvial swamp-type sediments of the Pennsylvanian which filled the depression. In excess of 25,000 feet of Carboniferous rocks are believed to be present in the deepest part of the Basin. Starting with the rift hypothesis, we can speculate on the kinds of sediments, their location and the structural features present beneath the Pennsylvanian surface. Using surface exposures and a limited amount of subsurface data, we theorize that (1) the Mississippian evaporites acted as glide zones which effectively divided the Basin into two horizontal structural layers. The rocks above the evaporites, responding to Appalachian stresses, formed the long diapiric folds with cores of overthickened evaporites. Below the evaporites the structures are related to movements of the rift floor, compaction closures and structures formed by differential horizontal movements of the rift walls. (2) The rift, in its deeper parts, will have more and a greater variety of marine rocks than the outcrops indicate. Should the rift hypothesis be correct, the possibility of finding hydrocarbons is enhanced."

Jan 1, 1972

By Nirmal Weerasekara

Mill liners serve the dual purpose of protecting the shell from wear and transferring the rotary motion of the mill to an effective grinding action. As the liners wear, the efficiency of energy transfer changes, so there is balance between liner profile for wear and for milling efficiency. A tool that can simultaneously predict the evolution of the liner profile and the associated change in milling efficiency should prove most useful in optimal liner design. This paper presents such an approach, based on measured 3D liner profile data informing 3D DEM simulations of charge motion and liner wear modelling.

Jan 1, 2012

By J. R. Fisher

"Uranium may be leached to some extent in situ from the Blind River conglomerate uranium ores by using the products of bacterial activity from the bacterium Thio-bacillus ferrooxidans his paper describes some of the laboratory techniques used to investigate the characteristics of the bacteria, and to utilize their properties in uranium leaching. The application of some of the laboratory results underground at the Milliken mine of Rio Algom Mines Limited are de-scribed, along with the method of uranium recovery from the mine waters."

Jan 1, 1966

By Lauri Pesonen

"Although electrical energy use at copper smelters is typically about 15-20% of operational costs, it is something which is not very often analyzed and discussed at a detail level in technical papers and presentations. This paper aims to list different equipment configurations per smelter area and estimate their electrical energy consumptions versus unit of material processed. In addition chosen smelting technology and oxygen enrichment rates affect the overall electricity consumption and therefore some overall guidance is provided for efficiency gains.INTRODUCTION In principle, processing plants, such as copper smelters, require electrical and chemical energy together with some degree of human input to process input materials into desirable output form like metallic copper. From the standpoint of metallurgical plant designers, the thermodynamics of smelting, when it comes to releasing and conserving thermal energy, is sufficiently understood and frequently discussed in the literature in detail, but judging from the quantity of publications, the way how we exactly utilize electrical energy is not. This article is meant to illustrate how electrical energy consumption is distributed among different process units and equipment types at copper smelters using various smelting technologies. In general, typically about 15-20% of operational costs are related to electricity and at locations with high electricity prices the potential savings can be quite significant for the overall profitability of the plant operations. In today’s tight profit margin environment any potential savings are more than welcome. The purpose here is not to promote any certain copper smelting technology, but to open a discussion on how and where we use electrical energy, and how the overall energy use could be lowered with the implementation of newest electric power saving designs and solutions. Using the principles outlined in this article, it should be fairly easy and straightforward to replicate the calculations and even improve them wherever it is seen necessary for the greater benefit for us all in this industry"

Jan 1, 2017

By M. G. Manzone

Approximately two-thirds of the annual 210,000 tons at copper refined by AMAX Inc. at the United States Metals Refining Company in Carteret, New Jersey, comes from a wide variety of copper scrap ranging from low-grade smelter scrap to wirebar-grade material. The equipment and methods used to effect such large-scale metal recycling in an urban area and the measures taken to collect and recover metal values from smelter and refinery byproducts while protecting the environment from pollution are described and discussed.

Jan 1, 1977

By Jonathan Matthews

Efficient and effective management of mine tailings is essential for continued successful development of Alberta?s vast oil sands resources. Syncrude Canada Ltd. continues to research novel tailings management techniques in an effort to improve production efficiency and environmental sustainability. During the summer months of 2001, Syncrude Canada Ltd., in collaboration with members of the Canadian Oil Sands Network for Research and Development (CONRAD), conducted field-scale trials of thickened tailings technology at Syncrude?s Aurora mine, north of Fort McMurray, Alberta. This paper provides an overview of the test program including discussion of objectives, test configuration, and program observations. 0Data collected during the field trial indicate that substantial swings in feed slurry composition challenge effective thickener operation. When coarse mineral solids dominated slurry composition, thickener rake torque rose to unmanageable levels. It was determined that the end-of-pipe depositional characteristics of thickened oil sands slurry were generally consistent with present understanding of oil sands tailings slurries. After shear, thickener underflow product exhibited very shallow beach angles and a limited capacity to keep coarser particles in suspension indicating that stacking of ?paste-like? thickener underflow product from a conventional thickener is not practical in an oil sands setting unless process adjustments can be made to increase the underflow density and/or preserve the initial high yield stress of the underflow during transport and deposition. These technical challenges notwithstanding, Thickened Tailings technology offers considerable promise for recovery of warm water from oil sands process tailings.

May 1, 2003

By Terry A. Lee

The grade of mineral resource estimates underpin all major economic considerations of mining prospects. While there are reporting requirements to satisfy when stating a mineral resource estimate, an examination of NI 43-101 style reports suggests that authors believe that there are a number of ways of addressing these requirements. As a reader of these reports, some processes are helpful and others are not so in getting a real appreciation of how realistic is the mineral resource estimate. Critical to the quality of the mineral resource estimate is how realistic is the economic mineral concentration component. In many cases, this parameter is called grade. The industry experiences increased difficulty in achieving realistic grade estimates as the sample grade variability increases. The level of transparency in a mineral resource estimate is very much a function of the competence of the author. An objective presentation of the critical data, such as grade sampling variability can assist a reader in determining if the geology of the mineral concentration is adequately understood and how realistic is mineral resource grade estimate. This paper has considered 75 NI 43-101 style reports released in the past 2 years. The review demonstrates features that were helpful in determining how realistic the mineral resource grade estimate is. If there is insufficient transparency in a report, there is a high probability that the mineral resource grade estimate will not be realistic.

Apr 1, 2005

By Northeastern University, B. Y. Cui, B. Y. Wang, D. Z. Wei, W. G. Liu, Z. C. Guan, S. L. Gao

To recover iron values from low grade ores by reverse froth flotation method, further research on cationic collectors used in reverse flotation of iron ores is launched to promote the utilization efficiency of iron ores. In this paper, one new cationic surfactant, bis(2-hydroxylethyl) dodecylamine (BHD), that could be dissolved in water easily was used as collector for quartz flotation. Flotation results indicated that BHD shows stronger collecting performance on quartz than hematite. The maximum recovery of 96.30% to quartz is obtained at a collector concentration of 20.0 mg/L in the pulp pH range from 5 to 7. This collector can be used to float quartz from hematite. And optimal separation results with 86.59% iron recovery and 66.60% iron grade to synthetic sample were achieved at a collector concentration of 20.0 mg/L and pulp pH of 5.02 when hematite and quartz were mixed at a mass ratio of 3:2. The adsorption mechanism of the collector on quartz surface was investigated by XPS analysis, infrared spectroscopic analysis and zeta-potential measurements, which revealed that electrostatic attraction and hydrogen bonding adsorption occur between collector and quartz surface.

Jan 1, 2016