Search Documents

By Z. -E. Nakagawa, O. Yamamoto

After the formation of a concentration gradient of SiC within C-C composite, either zircon or mullite thin films were coated on the surface by sol-gel process. Oxidation resistance tests of as-prepared composites with a couple consisting of a ceramic thin film and a SiC-gradient were then carried out in air at the temperature range from 600 to 1600°C. By the coating of zircon with a thickness of 1.5 µm, a pronounced oxidation resistance was observed; the mass loss by oxidation was almost negligible at 1000°C and one hundredth of original composite at 1400°C. In the case of the coating of mullite with a thickness of 1.0 pm, the marked improvement in oxidation resistance over the whole temperature range examined, from 600 to 1600°C, was found with the combination of a SiC-gradient and a mullite thin film

Jan 1, 2004

By T. Belem

In-stope backfill will cure under effective stress, which develops due to a combination of mechanical consolidation (free draining material) and ??chemical consolidation?? (self-desiccation mechanism). A good knowledge of all the drainage and consolidation characteristics of cemented paste backfill is crucial for a better design of underground backfilling sequencing. From many of the existing results and studies done by various authors, as well as the availability of some in-stope backfill pressure data measurements during and after filling, it is possible of developing a procedure of backfilling sequencing. Hence, the objective of this study is to provide a guide for underground backfilling sequencing in the view of preventing the development of excess pore pressure that will affect both the stability of the barricades and the strength development of the backfill. This will be possible by considering the interaction between consolidation/drainage rate, filling rate and binder hydration rate.

Aug 1, 2013

By W. J. Kuit

"Complex facilities which provide for the collection, management and treatment of effluents emanating from the Sullivan mine and concentrator tailings were made operational in October, 1979. Key features of the system are the use of upgraded tailings ponds for the storage of up to 800 million litres of metals-contaminated effluents, a treatment plant employing lime in a high density sludge process and a sludge-impoundment facility designed for maximum long-term environmental safety. The completed works are cap1ble of satisfying a difficult range of operating requirements imposed by highly variable weather conditions, drainage flows and soluble metals loadi11gs. Final capital expenditures for the project will approach $10 million and annual operating costs are estimated at $0.8 million.This paper discusses the Kimberley effluents treatment project and the major considerations in its development. The treatment process, major plant equipment and initial operating experience are also described."

Jan 1, 1980

By W. Evans, T. Steis

"Sulphide ores under certain circumstances will react with explosives to generate an autocatalytic chemical reaction. This reaction is exothermic and results in the production of large volumes of poisonous gases and creates an unsafe, unstable condition with the possibility of a low energy deflagration or even a detonation of the loaded hole. This paper outlines the conditions that need to exist for such a reaction to take place and the precautions necessary to minimize or eliminate the problem in areas of reactive ore. A special case study involving a northern Ontario mine will be detailed.IntroductionOne of North America's leading underground gold producer's processes over 6500 tonnes of ore per day from an orebody containing high concentrations of sulphides. After six years of problem free operation, the mine experienced two serious reactions in two months between the sulphides and AMEX II, the ammonium nitrate and fuel oil explosive it uses."

Jan 1, 1995

"This paper discusses the use of risk assessment and risk management techniques within the Australian underground coal mining industry, within the context of geotechnical risk. The industry works within a pro-active, “enabling” legislative framework, where companies and management apply a range of risk assessment tools as part of their everyday management processes. Different geotechnical risk factors and approaches are reviewed, together with application examples – ranging from mine planning and design, operations, and accident investigations.A particularly powerful resource in each of the above stages of geotechnical management is the RISKGATE system. RISKGATE is an assembled “body of knowledge” structured under different topics across the Australian coal industry, of which three topic areas address rock mechanics issues for both the underground and surface mining sector. This paper will provide an overview of RISKGATE in the context of risk-based rock mechanics applications in underground coal mining."

Jan 1, 2015

By Franco Chiesa, David Levasseur, Bernard Duchesne

A 500kg aluminium AlSi7Mg03 casting has been poured and the metallurgical quality at different locations inside the casting has been thoroughly investigated. It included measuring the local tensile properties (YS, UTS, El) in the T6 condition, the dendrite fineness (DAS) and the level of microporosity. A correlation was found between the microporosity level, the local solidification time and solidus front velocity; this correlation allows to predict the porosity level in large aluminium castings (solidification times between 20 and 200 minutes). Quite expectedly, properties varied widely within the casting and the actual mechanical properties were much less than the "textbook values" based on measurements carried out on separately cast standard specimens. A correlation between the secondary dendrite arm spacing (DAS) and the local solidification time was in keeping with previously published data. Finally the conditions to obtain an acceptable finish on machined surface were determined.

Jan 1, 2014

By Ken Musgrave

"A program is described that helps managers and supervisors control maintenance more effectively. Work- order generation, preventive maintenance, repair parts inventory, planning and scheduling, reporting, analyzing costs, printing purchase orders and other functions are covered. Flexibility often permits integration with other programs such as payroll, cost accounting and materials management.The Role of MaintenanceMaintenance provides a service to allow the rest of the operation to do its job effectively. Its success should not be measured by maintenance cost alone, but also by its effectiveness in reducing downtime and maximizing production. It can make sense to spend more maintenance dollars if this results in an even greater contribution from increased production.The Cost of MaintenanceIn mining companies, maintenance costs can be as much as half of operating costs. Maintenance has generally not been given the management attention that an expenditure of this magnitude deserves."

Jan 1, 1986

By J. E. Zajic, E. A. Sullivan, T. R. Jack

"The release of vanadium, iron, nickel and titanium from the cokes produced in the upgrading of Alberta oil sands bitumen has been assessed for simple chemical leaching processes. Flexicoker coke (Exxon Engineering and Research) has been found to be quite amenable to the recovery of vanadium as well as nickel, iron and some titanium by these techniques, whereas fluid coker coke (Syncrude) and delayed coker coke (Great Canadian Oil Sands) are relatively intractable under the mild conditions employed. The factors affecting the extent of vanadium release are discussed in terms of the surface area accessible, the wettability of the material, and the chemical and physical composition of the coke particles in each case.A novel biologically assisted heap leaching procedure for f1exicoker coke is also described, based on the growth of the chemolithotrophic bacteria, Thiobacillus thiooxidans A TCC 8085, on elemental sulphur added to the coke."

Jan 1, 1980

By H. R. Butler

"The Ontario Division of Inca Metals Company, a Unit of Inca Limited, operates eleven mines, four mills, three refineries, one smelter and one iron ore recovery plant. All but one mine, mill and refinery are located within a fifty kilometer radius of Sudbury, Ontario. A mine-mill complex is located some 100 kilometers west of Thunder Bay on the shore of Lake Shebandowan and a nickel refinery at Port Colborne.During the past 10 years the use of recycled water in our milling operations has increased to more than 95% at each mill. This high degree of water reuse has reduced the (a) need for fresh water and (b) the contaminant level of the downstream aquatic environment. The aggregating of effluents in a common receptor provides a process water having a consistent quality thereby minimizing upsets in mill metallurgy while concurrently improving the operating economies and the downstream aquatic environment."

Jan 1, 1980

By A. S. Gendron

A brief description of Inco's ORC copper refinery tankhouse and the electrowinning tankhouse is followed by a comparison of the requirements for the production of the high-quality copper in both systems. The description will focus on both tankhouses, with emphasis on experience to date in the electrowinning tankhouse. Particular attention will be paid to sensitivities of each tankhouse to process upsets which can. significantly afject the quality of the product cathodes.

Jan 1, 1977

By E. V. Manlapig, M. A. Hampton, M. E. Holuszko

Methanol treatment of ZnS particles has been found to remove slimes and facilitate flotation. The removal of slimes renders the ZnS surface more hydrophobic, resulting in an increase in the hydrophobic attractive force between the particle and bubble. Hallimond tube flotation, induction time measurement and particle-bubble force analysis with the atomic force microscope (AFM) was undertaken to link the beneficial effect of methanol treatment of ZnS particles to their increased floatability.

Jan 1, 2009

By W. R. Tyson

Pipelines for the transport of gas and oil are being designed to operate at increasing pressures in increasingly harsh environments. The steel used to construct these pipelines must have adequate toughness to tolerate weld imperfections (i.e. withstand bending strains) and to arrest running cracks (i.e. to prevent propagation of axial fractures). The problems posed in specifying suitable toughness parameters and the approaches currently being used to measure them are discussed.

Jan 1, 2005

By Harry R. Oldale

This paper first covers the general and economic geology of the Coxheath Hills area, and then outlines the exploration and mining development that has been carried out since the first discovery of copper in the area in 1875. The work of Mariner Mines Limited from 1963 to the present time is detailed, particular attention being paid to the recent discoveries of copper, silver and lead mineralization that have greatly enhanced the potential of the area.

Jan 1, 1967

By W. E. Coates

The social ecology of surface mining in urban areas is illustrated by a case study of a recent application for the opening of a new gravel pit in the city of Guelph, including the design of a progressive extraction-rehabilitation sequence for the property, investigation of the ecological impact of the proposed operation, history of the application procedure for a zoning change and the relationship of the operating plan to provincial legislation controlling surface mining.

Jan 1, 1972

By Paykan Safe

?? Background ?? WorleyParsons Gas Cleaning ?? PT Inco Smelter ?? Process Design Considerations ?? Furnace Control and Combustion ?? Combustion Chamber ?? Spray Chamber ?? Draft Control ?? Baghouse ?? Secondary Ventilation ?? ID Fan ?? Dust Handling Equipment ?? Project Execution ?? Heat Recovery ?? Conclusion ?? WorleyParsons Gas Cleaning ? Irving, TX ?? Formerly Gas Cleaning Technologies ?? Acquired by WorleyParsons in 2005 and now part of a global EPCM company ?? 14 years experience in off-gas system design for ferrous and non-ferrous facilities worldwide

May 1, 2008

By M. Rigaud, N. Zhou, K. Sankaranarayanane, X. Zhou

The effect of amount and type of dispersants on the rheological behaviour of bauxite-based low-cement castables has been studied in detail. The rheological properties: flow resistance and torque viscosity, as measured by a rheometer, are found to be strongly influenced by the amount and type of dispersants. In the present investigation, a mix containing sodium hexametaphosphate, at an optimal level, is observed to be theologically superior at the given experimental conditions.

Jan 1, 2004

By J. C. Ingles

"A new technique is in the process of revolutionizing inorganic chemical analysis. Galled atomic absorption spectrophotometry, it combines the use of a special light source, a flame, and the equipment of conventional spectrophotometry, to provide a quick, reasonably accurate method for the determination of a large number of elements.This paper outlines the principles on which it is based, describes the commercial instrumentation"" available for exploiting it, and. summarizes current applications in process metallurgy."

Jan 1, 1966

By C. E. McCoy

This paper will discuss briefly loader shovel requirements and then present a detailed survey of electrical drive systems to meet these requirements. The survey in general will deal with the various electrical provisions for shovel drives, along with the advantages and disadvantages, and in particular will discuss the MG set and static D. C. drive systems. Also included will be some insight into the requirements for optimum electrical power at the shovels.

Jan 1, 1979

By D. T. White

"Metallurgical extraction processes often call for the heating of aqueous slurries. Indirect heat exchangers are generally not feasible for service with high yield stress slurries because of low heat transfer rates. It is more appropriate to heat the slurry by direct contact, typically with steam as the heating medium. Although having a long and successful history, direct-contact heat transfer to aqueous slurries has been used without the support of pilot plant research. This paper provides results of the needed research, the work being done at a scale large enough to enable direct scale up to commercial operations. A pilot plant heater was constructed and tested to develop an understanding of the slurry heating process and to ensure that commercial scale heaters were appropriately sized.INTRODUCTIONPressure Leaching OperationsPressure leaching operations are often used to oxidise sulphide gold ores, or for extraction of nickel and cobalt from laterite ores with sulphuric acid. Where there is sufficient sulphur available, the exothermic pressure oxidation reactions can be self sustaining at temperatures as high as 225 ºC, without having to preheat the feed slurry. At lower sulphur levels, slurry preheating is required. This is typically achieved by utilising the flash steam released from the slurry letdown stages and contacting this directly with cold incoming slurry ahead of the autoclave. The vessels where this slurry-steam contact is made are known as heaters or condensers, with the number of pre-heat stages varying, depending on how much heat is evolved in the oxidation reaction (Mason, 1990).In nickel laterite pressure acid leaching processes, which operate between 245 and 270 ºC, the only significant exothermic reactions are those associated with dilution of sulphuric acid in the leach. As a consequence, slurry preheating with flash steam is always used commercially. In practice the number of flash steam preheating stages required varies from 1 to 3, driven by a number of factors, including other uses for flash steam and the upper temperature limit at which preheated slurry can be pumped. A diagram of a typical pressure acid leach train is shown in Figure 1.For pressure acid leaching operations and at low sulphur levels in pressure oxidation, boiler generated direct steam addition to the autoclave is required to sustain the reaction temperature. For this reason it is imperative that the flash steam – slurry heat transfer is efficient and the slurry temperature approaches that of the flash steam closely."

Jan 1, 2012

By C. Harold Riches

This article is directed co a commentary on the patent system in its relation to the public interest. As man gained supremacy over his environment, he could devote progressively increasing portions o his time to improving his standards of living. In the history of the human race, we have advanced from the hollowed floating log to the modern steamship of the present age; from the sickle and flail to the reaper and combine; from the trumpet and drum as a means of communication co the telegraph, telephone, and radio; from the horse and ox cart to the automobile, truck, aeroplane, and train; and so on ad infinitum through the list of inventions on which are based the industrial and political economies and standards of living we enjoy today. It has also been a long road from the day of the alchemist and his closely guarded secrets to the era of the patent system and its storehouses of knowledge open to the world. The alchemist and the craft and merchant guilds closely guarded their secrets. In fact, they largely opposed innovations on the grounds that they might injure profits and restrict employment. In these days of unrest, with great clamour out of doors for radical changes in our political and industrial economies, it may not be untimely to examine one of the keystones which support the economic structure we know as the free enterprise system, the system which is predicated upon the right of the individual to own property. Many, through impractical idealism, ignorance, confused thinking, or blind political prejudice, advocate the substitution of ownership by the State ? for the right of ownership by the individual. As civilization has advanced to the high standards of living we enjoy today through the efforts of a comparatively few inventors, the patent system which has provided the incentive that created the inventions on which our industries and our employment are based is fully understood and appreciated by a comparatively small percentage of our people. As a result, the patent system, as a keystone in our free enterprise economy, is an apt target for destructive criticism, with the thought, possibly, that by eliminating or drastically restricting the several rights to individual ownership one by one, ownership by the State will progressively replace ownership by the individual.

Jan 1, 1949