Search Documents

By H. Miki, S. Wheatley

The addition of precipitated silica greatly enhances chalcopyrite leaching in the presence of sodium chloride at moderate temperatures (65-90°C) in acid media with ferric ions as the oxidant. The beneficial effect increases with the increase in chloride concentration and temperature. The addition of sodium silicate and silica sand has no significant influence. The analysis of solubility data in acid/salt solutions indicates that the solubility of silica as Si(OH)4 as the dissolved species is controlled by the activity of water, as expected from the hydration theory. Kinetic analysis shows the trends that copper dissolution from chalcopyrite in the presence of precipitated silica with sodium chloride follows a shrinking sphere model indicating a chemically controlled surface reaction. The effect of temperature on copper dissolution in the presence of both precipitated silica and sodium chloride was also larger compared to the results in sodium chloride alone. The SEM analysis shows that chloride and silica facilitates the precipitation of sulfur on the surface of the silica particles rather than the chalcopyrite particles which avoids the blockage of the mineral surface and thus improves the leaching kinetics.

Jan 1, 2014

By K. J. Daun, C. J. Shi

UsiborThrough the second step heating at 900 °C, the spectral emissivity shows a gradually decreasing trend with increasing soak time, caused by the surface phase transformation from Al® 1500P coupons are austenitized in a Gleeble 3500 thermomechanical simulator using a two-step heating procedure in an argon atmosphere. Variations in spectral emissivity are measured in-situ using a near infrared spectrometer and ex-situ with a Fourier transform infrared reflectometer. Microstructural evolution and surface roughness are investigated using optical microscopy, FE-scanning electron microscopy, and a surface profilometer. A series of phase transformations of Al-Fe-Si intermetallic phases at the coating/steel substrate interface cause the surface phase and surface roughness to change, which in turn influences the spectral emissivity. At the beginning of the first heating step, the coupons have very low spectral emissivity, due to the molten Al-Si coating. Spectral emissivity increases significantly with increasing soak time from 5 to 12 minutes, associated with the surface phase transformation of the coating into Al7Fe2Si intermetallic phase and an increase in surface roughness. 5Fe2 into AlFe intermetallic phase with a decrease in surface roughness.

Jan 1, 2015

By Bradford P. Simser

The theoretical capacity of various ground support components can be misleading, especially in bursting ground where the failure mode is often in the retainment system. Wire mesh screen seams often peel open rather than breaking the wire strands, fractured rock often un-ravels around the bolts rather than breaking the bars. If a weak link(s) in the system fails prematurely, then the potential capacity of the system may never be fully realized. Underground observations are used to show how some support systems behave in the field. Various combinations of wire mesh screen with friction bolts, rebar, modified conebolts, cablebolts, shotcrete and mechanical rockbolts are considered. A short case history is used to contrast the performance of ?just-intime? development in a high stress faulted area versus a tunnel subjected to multiple stress changes in a similar environment. The latter proved to be a serious ground support problem when the well developed fracture zone around the opening was subjected to dynamic loading from a large seismic event causing a severe rockburst. In such cases an improved mining strategy may be more relevant than higher capacity support systems.

Feb 1, 2008

By Mory Ghomshei

Pebble Creek Geothermal Power project is associated with a massive recent volcanic eruption in Southwestern British Columbia Canada. Slim holes drilled to depths 1100 m in the prospect area, show very high temperature gradients around 80?100?C/km. The temperature and chemistry of the Pebble Creek hot springs indicate the possibility of a steam reservoir in the prospect area. In addition to high temperature gradients, presence of host rocks with high permeability, along with abundance of recharge waters (from the Lillooet River) provides clear signature of a high-grade geothermal power reservoir at depth 2000 to 3000 m. Data show that over five hundred Megawatt of green power can be generated from the prospect area in a commercially viable manner. The generated power will be base-load, which in comparison with large hydro has the advantage of lower capital costs and a significantly smaller footprint. The final hurdle to overcome, before starting the development phase, is deep exploratory drilling for resource confirmation. This paper is a summary of the data available on the Pebble Creek geothermal power prospect, presented in the context of viability of the resource for large-scale commercial power generation.

Aug 1, 2013

By Paolo Farina

Slope monitoring radar has emerged in the last ten years as a leading edge tool for monitoring movements in natural and engineered slopes, thanks to its ability to rapidly measure slope movements with millimetric accuracy over wide areas in any weather conditions, obviating the need to install artificial reflectors. In recent years, slope monitoring radar has experienced significant improvements in its performances, mainly thanks to the use of different radar technology, such as Synthetic Aperture Radar (SAR), able to overcome some of the limitations of the first generation of radar and to provide higher spatial resolution, longer working distances and faster acquisition time. One of the leading applications of this technology is today represented by slope monitoring within the surface mining industry. Prominent international mining groups currently employ slope monitoring radar, based either on Real Aperture Radar (RAR) and SAR technology, for active and background monitoring of open-pit walls. The main technical features of typical slope monitoring radar based on SAR technology along with their possible applications are presented in this paper along with recent case studies of successful slope monitoring in open pit mines.

Jun 1, 2012

By Alan F. Stewart, Frederic B. Claridge, Robert S. Nichols

"In recent years, an increasing number of mines in mountainous terrain have examined the possibility of placing mine waste rock into stream valleys. Pressure to utilize stream valleys as a primary location for waste disposal has increased at many of the mines currently under development or expansion. As the number of environmentally and economically ideal wastedumping sites is limited, consideration must be given to utilization of stream valleys. This raises concerns about maintaining water quality in streams passing through or beneath the dumps and potential detrimental effects to dump stability. Commonly, the flows in the streams tend to be flashy, reflecting localized intense storms and rapid runoff in steep-sided slopes within the watershed. These conditions pertain particularly to British Columbia, which is characterized by mountainous terrain and periodically intense precipitation events.The method of conveying flow through a waste dump depends on a number of geotechnical and hydrological factors, including the size, durability and transmissivity of the rock and the design stream flood flow. This paper describes the approach to the design of waste dumps in stream valfeys developed at several mines in British Columbia."

Jan 1, 1986

By S. Asano

Hydrometallurgical processes for treating copper sulfide concentrates have attracted considerable attention over thirty years and many processes have been developed. However there have been still problems in those processes because of difficulties of iron removal and high purity copper production with low operating cost. Although SX-EW is highly cost effective method, it is difficult to process the chalcopyrite. Sumitomo Metal Mining Co., Ltd. (SMM) conducted a review of hydrometallurgical copper concentrate processing and has successfully developed a novel process for the hydrometallurgical production of copper from copper concentrate. In this process, copper sulfide is leached by chlorine gas under atmospheric pressure. Most of hydro metallurgical processes can leach only some of chalcopyrite under atmospheric pressure then they need high pressure leaching facility like autoclave. In this process, copper in chalcopyrite can be leached completely by controlling oxidation reduction potential and chloride ion concentration. Cu(I) ion in leached liquor is separated from Fe(I!) ion by SX using TBP then pure copper powder is produced by electrowinning. Results in batch and continuous testworks and pilot plant tests at Niihama Research Laboratories are presented in this paper. Cu2007

Jan 1, 2007

By J. A. Muñoz

In this work, short and long-term tests were performed using different massive mineral sulfide specimens (chalcopyrite, pyrite, sphalerite, galena, covellite and chalcocite) of museum grade and quartz of analytical grade in an acid medium containing silver ions. After attack, the samples were observed by SEM and products characterized by EDS. Parallel, massive specimens of pyrite (FeS2) and chalcopyrite (CuFeS2) were embedded in an epoxy resin, either electrically isolated or in electrical contact, and treated with silver ions in the presence of bacteria. Finally, massive chalcopyrite and pyrite electrodes were subjected to electrochemical measurements in an acid medium under different experimental conditions (addition of silver ions and inoculation). The results showed that silver deposition takes place preferentially on specific mineral surfaces: chalcopyrite, galena, covellite and chalcocite. The chemical reaction of silver ions with pyrite and sphalerite was negligible at low silver concentration (8 ppm). But sphalerite reacted with silver ions at higher silver concentration (100 ppm). In a mixture of chalcopyrite and pyrite, silver was deposited on the former surface creating new cathodic sites which sped up the electrochemical reactions of chalcopyrite dissolution.

Jan 1, 2007

By C. Okay Aksoy

In Turkey, the increasing demand for lignite has necessitated an increased emphasis on both lignite production and recovery. This emphasis has resulted in a gradual increase in the application of the retreat longwall mining method for both its product recovery and productivity benefits. Also, in order to maximize the recovery of the natural resources and to increase total production, it is necessary to take advantage of underground reserve before abandoning the mine. This means that at the end of the life of the mine, the main drift safety pillar and the shaft pillar will generally be extracted. This investigation a preliminary study of the stability of the main drift and the shaft at the Hustas Mine as the safety pillars are extracted. In this study, field surveys belonging to the underground colliery of Hustas Co. in Soma have been investigated with the help of LAMODEL working under the Laminated Displacement Discontinuity principle for the models calibrated as a results of physical model and finite element analyses. The convenience of Laminated Displacement Discontinuity Analysis has been researched in such studies. The results out of the models have been coherent with the previous studies.

May 1, 2004

By M. Lahtinen, H. Takala, B. Saxén

Oxidic zinc fume dusts are formed in electric arc furnace (EAF), Waelz furnace operations, and also in the Top Submerged Lance (TSL) furnace of Outotec Ausmelt. These dusts are normally considered as secondary raw materials for zinc metal production, as they are mainly originated from steel scrap recycling or zinc plant residue processing. The latest development in zinc fuming is direct smelting of zinc concentrates in the Ausmelt TSL furnace and hydrometallurgical treatment of produced fume dust. This technology is for primary zinc production like roasting and concentrate direct leaching, as concentrates are directly treated. The various oxidic zinc raw materials differ in composition and content of impurities. Thus, they require different hydrometallurgical processes to produce pure zinc metal. In addition to zinc these dusts typically contain also lead, silver and indium, which can be recovered and can increase recovered metal value significantly. From the impurity point of view the most relevant elements in the fume dusts are iron, arsenic, fluoride, chloride and cadmium. This paper describes hydrometallurgical processes to treat Ausmelt TSL fume dusts to extract valuable metals at high recovery and also to control and separate various impurities efficiently.

Jan 1, 2014

By S. Markstrom

The Boliden AITIK copper mine is located 100 kilometres north of the Arctic Circle in northern Sweden. A pre-feasibility study was conducted in 2005 with the aim of increasing the capacity of the existing processing plant. After analysis, options to upgrade the existing plant were abandoned in favour of building a new processing plant, with higher capacity and therefore greater profitability. A new plant could be designed with greater flexibility to make potential future expansions easier. A feasibility study for a new 36 Mt/y processing plant including fully AG grinding circuits and flotation was completed in 2006. The project was approved by the Boliden board shortly thereafter. Construction started in the beginning of 2007 and was completed during 2009. Commissioning of the new plant was undertaken in the first half of 2010. The grinding circuit consists of two lines with each line consisting of a 22.5 MW AG mill and a 10 MW Pebble mill in closed circuit with a spiral classifier. The nominal production level is 2 200 t/h for each grinding line. This paper presents the start-up and operation of the grinding circuit.

Jan 1, 2012

By Robert B. Parsons

"In all likelihood, Canada's mining industry would be adversely affected by corporate tax reform proposals actively being considered by the Department of Finance in Ottawa. When the next set of proposals for lax reform is released later this year as promised by Finance, the mining industry had better be prepared 10 take a hard look.IntroductionTwo federal budgets ago, in May 1985, Finance Minister Wilson tabled budget papers that were more massive in terms of volume than most federal budgets. Buried in this mass of documentation is a discussion paper entitled ""The Corporate Income Tax System-A Direction For Change"". When the discussion paper was tabled over one year ago, reaction from the business sector was almost nonexistent. By and large, the paper was regarded as nothing more than one more federal publication of mild academic interest.But, recent events suggest that this discussion paper for corporate tax reform could be the cornerstone for a series of changes to the tax laws which would have more profound and widespread effects for all sectors of the economy than any reform since 1971 . No industry in Canada can afford to ignore the movement afoot in Ottawa for corporate tax reform."

Jan 1, 1986

By E. C. W. Perryman

Materials research and development has played an important role in the commercial success of the CANDU- PHW nuclear reactor and in the production of heavy water. Both capital investment and energy conservation demand very high component reliability in such systems. The interactions among reliability, plant performance and economics will be discussed in relation to materials research and development. Likely materials requirements for the nuclear industry over the next twenty five years will also be discussed.

Jan 1, 1977

By R. D. Brown

"Taxation tends to be a depressing subject. Taxes are unfair, taxes are too high and, above all, taxes are too complicated.In a recent address to the Canadian Tax Foundation, the author discussed in a rather more lighthearted way the possible causes of the complexity of the present Canadian taxation system. In order to provide an element of relief in this series of articles on taxation matters, extracts from these remarks are quoted below :"

Jan 1, 1976

By J. Schmidt

The development of set of laboratory experiments, intended to help undergraduate students meet Canadian Engineering Accreditation Board requirements for Engineering Design outcomes, is described.The laboratory, which is part of a third year level course in hydrometallurgy, is aimed at advancing the ability of students to generate and use experimental results to design an industrial copper leach/SX/EW plant. Emphasis is placed on the students demonstrating the ability to use of their engineering knowledge in weighing the pros and cons of the various process options that they test in converging to a final flowsheet. INTRODUCTION Over the past number of years the Canadian Engineering Accreditation Board, CEAB, has dramatically shifted the way that they evaluate undergraduate programs. In the past, the focus was on measuring of the quantity and quality of material the students were intended to learn as well as the methods and resources used to deliver that material. Now, rather than principally evaluating the inputs of programs, the focus is more on measuring the quality of the outputs from the programs, i.e. the quality of graduating students. In this regard, the CEAB has developed a list of twelve attributes that learners must develop in the course of their studies. Engineering programs must, not only demonstrate that their curriculums provide opportunities to develop these attributes, but must measure student proficiency in each of these attributes as they progress toward graduation. One particular graduate attribute that Laurentian University’s Bharti School of Engineering has encouraged its faculty members to develop content for is “design”. Engineering Canada (2018) defines this attribute as “an ability to design solutions for complex, open-ended engineering problems and to design systems, components or processes that meet specified needs with appropriate attention to health and safety risks, applicable standards, and economic, environmental, cultural and societal considerations”. The previous laboratory component for the hydrometallurgy course was a collection of unconnected experiments covering leaching, solvent extraction, ion exchange, and electrowinning. Like in other undergraduate courses, students would perform stand-alone experiments, make the specified measurements, do the specified analyses of the results, and report the findings, all as strictly detailed in the lab manual. The vision for the new lab was to create an experience that would more closely mimic an industrial research program whereby students would start with a given feed material and would progress through a series of connected experiments. Emphasis is placed on the student demonstrating competency in, not only, generating and analyzing experimental data, but also in using the data along with their engineering knowledge to design and evaluate the pros and cons various plant configuration options. Principally, students are asked to weigh cost, safety, and environmental concerns in converging to their final flowsheet. In designed the leach circuit, students must weigh the costs/benefits of varying leach temperature. Higher leach temperatures will yield faster and more complete copper dissolution, which will allow for the specification of relatively smaller leaching circuits, saving capital costs. However, hotter acid solutions are more dangerous to handle and require increasing amounts of energy to heat the slurry, increasing operating costs. In solid/liquid separation, students must weigh the pros and cons of the addition of a flocculent to assist settling. The flocculant will allow for the design of a thickener circuit that employs units with a relatively smaller area, but will result in a thickener underflow with a lower pulp density, which may necessitate a larger number of thickeners. In addition, the environmental concerns of producing a tailings product that contains an organic contaminant should be addressed. In solvent extraction, students must specify the number of stages of loading and stripping, as well as organic and aqueous flowrates to produce suitable raffinate and rich electrolyte streams. Finally, in electrowinning, students will compare the costs/benefits and risks of the use of precious metal coated titanium dimensionally stable anodes (DSAs) versus conventional Pb based anodes.

Jan 1, 2019

By H. Kolcz, G. S. Dobby, R. Stratton-Crawley, S. W. Wilson

"The Matte Separation plant at Inco's Copper Cliff Smelter Complex is described. The continuing implementation of flotation column technology in the flowsheet in various applications is reviewed. Comparative studies on 0.038, 0.10, 1.1 and 1.8 m diameter columns have been carried out. It was demonstrated that consistent metallurgical performance was obtained with both pilot- and plant-scale units. Grade-recovery relationships for plant columns can be predicted with confidence from data obtained from test equipment. The work indicates further areas of the flowsheet in which columns present an attractive alternative to conventional cells. INCO’s MATTE SEPARATION PROCESSNickel concentrate from Inco’s Sudbury area mills has been processed in the Copper Cliff smelter for sixty years. Prior to that, Sudbury ores had been smelted directly. Historically, copper-nickel separation from smelter converter matte was achieved by the classical Orford process. In the mid-1940s Inco developed an improved separation scheme based on mineral processing methods, the Matte Separation Process. A generalized Copper Cliff Smelter Complex flowsheet is shown in Figure 1.Iron sulfide and gangue contained in the nickel concentrate are rejected in the smelting-converting process. The molten product, typically containing 50% Ni, 25% CU and 22% s, is cast at about 1000 ºC, into floor moulds and allowed to slowly cool for four days. During this period nickel sulfide (heazlewoodite, Ni,S,), copper sulfide (chalcocite, cu,S) and a copper-nickel metallic alloy precipitate and form a coarse grain structure that is amenable to separation by physical means. The phase chemistry of this system has been described previously by Sproule et al (1). This matte then becomes the feed to the Matte Separation Process.A simplified block flowsheet of the Matte Separation Process is shown in Figure 2. Matte ingots, typically weighing 20 tonnes each, are broken and crushed in a three stage crushing plant to approximately minus 0.01 m and conveyed to the Matte Separation building. Grinding is carried out in two parallel circuits each consisting of a rod and ball mill in series producing a flotation feed which is 65% minus 44 microns. Typical throughput of each grinding circuit is 650 tonnes/day. The metallic fraction of the feed is recovered by magnetic separation. This product, containing about 66% Ni and 15% CU, is a major component of the feed to the Copper Cliff Nickel Refinery."

Jan 1, 1990

By T. Schepp, T. Friedrich

"The natural stage of deep mines operation is a closure of unnecessary shafts. It is extremely important to ensure a proper shaft closure to avoid stability loss and the associated damage to surface facilities in the future. For the still active shafts, it can be done by a dedicated shaft closure design, but even then, depending on the shaft closure method, it may be necessary to perform regular shaft inspections. The paper presents a short overview of shaft closure methods and available tools and devices developed in the last time for such shaft inspections. INTRODUCTION The natural stage of deep mines operation, commonly occurring after depletion of the reserves of mined materials, is a closure of unnecessary shafts. All over the world, the number of liquidated shafts grows continuously and the problem of shafts disposal is especially critical for deep shafts. The typical depth of 600 m of currently liquidated shafts in Poland may already be seen as a challenging task. The greater is the challenge of shaft closure in Germany where the last active coal mines for shafts with a depth of up to 1,300 m have been recently closed. It is therefore extremely important to ensure a proper shaft closure to avoid stability loss and the associated damage to surface facilities in the future. For the still active shafts, it can be done by a dedicated shaft closure design, but even then, depending on the shaft closure method, it may be necessary to perform regular shaft inspections. In many cases, it is more important to inspect old, abandoned shafts, where the wall stability or even liner type are not fully known. SHAFT CLOSURE METHODS Abandoning a shaft is a complicated task, as shafts, being the link between the surface and an underground network of workings, disturb hydrogeological and gaseous conditions in the rock mass (Sztelak, 1991). Closure procedures at older mine sites have been carried out in accordance with earlier legislative requirements. For very old shafts (+100 years), it means in many cases only a sealing of the shaft entrances by means of timber or concrete slabs. In the 20th century, the shafts were also closed by means of filling with grainy materials, but even then the retrospective activities at abandoned mine sites were extremely limited and in most cases no further monitoring measures were performed. The possible consequence of an improper shaft closure and lack of monitoring is presented in Figure 1."

Jan 1, 2019

By Cheowchan Leelasukseree

Mae Moh mine, operated by Electricity Generation Authority of Thailand (EGAT), is the largest open pit mine in Southeast Asia. Its production is approximately 15 million lignite tons and 90 million m3 of waste, annually. The bottom of the final pit limit is designed to be approximately 500 m in depth. Presently, the pit depth is almost 250 m below original surface. The complexity of geological structures, such as faults, has caused a number of geotechnical difficulties. In a challenging lowwall area, called Area 4.1, an inclined weak bedding plane, G1, will be daylighted along the lowwall as following by mine plans. The dimensions of Area 4.1 are nearly 300 m wide and 90 m high. The friction and dip angles of the G1 interface are reportedly 12° and 15°, respectively. A three million m3 claystone block, resting above G1, would potentially slide down, and possibly cause a massive failure. EGAT engineers are acutely aware of the potential gigantic sliding failure and are modifying the mine plan in Area 4.1 to improve mine safety and minimize the displacement of the potential sliding block, reduce the possibility of failure and lower the additional mining cost as much as possible. The cut and fill mining technique was selected and studied to achieve those goals for mining in Area 4.1. With this mining technique, G1 will be partially daylighted. Therefore, an arch formation is induced with a sliding block above the mining area, which could perform as a temporary support undercutting a certain span. Initial studies of the behavior of the partially undercut slope are presented in this paper, along with a review of the similar failure history in Mae Moh mine and a 3-dimensional numerical model of the mine. The failure history review provides an estimation of undercut span without failure. The three-dimensional numerical model results, using 3DEC, gave an initial approximation of the displacement of the sliding block in Area 4.1. The next exciting study of the behavior of partially undercut slope is a trial undercut slope field experiment in Area 4.1. Currently, a trial undercut slope field experiment in Area 4.1 is under construction. In the field experiment, a number of monitoring programs will be installed in Area 4.1 to monitor and obtain information to allow a better understanding of the behavior.

Jun 1, 2012

By K. E. Harley, M. J. Whiting, T. J. Sabin, E. M. Ryan, J. F. Watts

"Wire and Arc Additive Manufacturing (WAAM) has the potential to enable a very significant reduction in buy-to-fly ratio compared to conventional manufacturing through the ability to build near-net shape components. Components manufactured from AA 2319 by WAAM can exhibit significant levels of porosity. There is also a variation in the physical appearance of the surface deposit sometimes found on such components. This deposit is similar to those observed on aluminium joined by MIG and TIG welding processes. It has been suggested that both the bulk porosity and the surface deposit are caused by hydrocarbon-based lubricant on the feedstock wire. An established correlation between surface deposit and porosity would offer valuable insight into WAAM products and enable early interventions in quality control or process monitoring based on visual examination. The relationship between the nature of the surface deposit and porosity has been studied for AA 2319 WAAM components manufactured using different wire batches. Evidence is presented to support the assertion that (i) there does not appear to be a relationship between surface deposit coverage and porosity, (ii) batch-to-batch variability in feedstock wire affects porosity. This study has led to a better understanding of the cause of porosity in WAAM components.INTRODUCTION There is a high cost associated with conventional, subtractive manufacturing because of the high ‘buy-to-fly’ ratio, a measure of the initial material bought compared to the material found in the finished part (Allen, 2006; Yilmaz & Ulga, 2016). A typical aerospace product may have up to 90% of the purchased billet of forging machined away which is cost inefficient and high in material waste. Wire and Arc Additive Manufacturing (WAAM) has the potential to reduce costs and lead time. Robotically controlled weld torches rapidly deposit feedstock wire in layers to build large near-net shapes with mechanical properties similar to those of conventional manufactured parts (Sequeira Almedia & Williams, 2010; Martina et al., 2012; Ding et al., 2015; Williams et al., 2015). A high level of porosity variation has been observed in aluminium WAAM parts (Cong, Ding & Williams, 2014; Gu et al, 2016) which can result in a range of material properties (Rudy & Rupert, 1970). This leads to difficulties in regards to standardisation and qualification of process and parts. In order for WAAM to be used commercially, porosity will need to be understood, monitored and reduced to a reproducible acceptable level or eliminated."

Jan 1, 2018

By S. V. Ulianov, A. Y. Senchenko, E. M. Kurchevskaya

"A process sample of old copper-containing tailings (-2.0+0 mm) from an iron-ore plant was tested in TOMS institute in order to develop a process for copper concentrate production. The study of tailings material composition indicated that -0.2+0 mm fraction was efficient and contained 97.26% of copper. Copper is predominantly concentrated in chalcopyrite which is present both in free form and in intergrowth with ore and rock-forming minerals. Study of chalcopyrite using an optical microscope and Qemscan SEM determined that the most grains surface was covered with oxide films. Additionally, a lot of grains had micropores on their surfaces that indicated a partial mineral leaching. The oxide films did not make it possible to float copper minerals from head material. It was recommended to apply an attrition operation to restore chalcopyrite floatability. In order to increase selectivity a regrinding stage for a primary copper concentrate was introduced to obtain P80 26 um. Taking these recommendations into account a flotation flowsheet was developed to process the old Cu-containing tailings. The flowsheet allowed us to obtain a concentrate with 23.5% Cu content at 71.5% recovery.INTRODUCTIONStudy of material composition is an important prerequisite for development of a minerals processing technology. Mineralogical study contributes to search for an efficient technology to recover valuables and for prospective methods of minerals processing.The use of such up-to-date analysis methods and equipment as Qemscan and Mineral-C7 allows one to determine minerals size, liberation degree, and mineral associations. Mineralogical data can reveal reasons for hard processing of minerals prior to development of the process.The advanced process mineralogical methods used to study Cu-bearing pond tailings indicated several factors that influenced development of the process. The first one is a barren size fraction which is to be removed from the process in order to considerably reduce the costs connected with grinding. The second is the presence of films on chalcopyrite surface; in this context, a preliminary attrition of the material was recommended. The third factor is finely disseminated Cu minerals in sulphide and in the rock, which predetermined selection of particle size for flotation. All these data led to significant decrease in time required to develop the process technology. The developed process flowsheet based on the obtained mineralogical data is present in Figure 1."

Jan 1, 2016