Search Documents

By M. Rigaud, N. Zhou, K. Sankaranarayanane, X. Zhou

The effect of amount and type of dispersants on the rheological behaviour of bauxite-based low-cement castables has been studied in detail. The rheological properties: flow resistance and torque viscosity, as measured by a rheometer, are found to be strongly influenced by the amount and type of dispersants. In the present investigation, a mix containing sodium hexametaphosphate, at an optimal level, is observed to be theologically superior at the given experimental conditions.

Jan 1, 2004

By J. C. Ingles

"A new technique is in the process of revolutionizing inorganic chemical analysis. Galled atomic absorption spectrophotometry, it combines the use of a special light source, a flame, and the equipment of conventional spectrophotometry, to provide a quick, reasonably accurate method for the determination of a large number of elements.This paper outlines the principles on which it is based, describes the commercial instrumentation"" available for exploiting it, and. summarizes current applications in process metallurgy."

Jan 1, 1966

By D. T. White

"Metallurgical extraction processes often call for the heating of aqueous slurries. Indirect heat exchangers are generally not feasible for service with high yield stress slurries because of low heat transfer rates. It is more appropriate to heat the slurry by direct contact, typically with steam as the heating medium. Although having a long and successful history, direct-contact heat transfer to aqueous slurries has been used without the support of pilot plant research. This paper provides results of the needed research, the work being done at a scale large enough to enable direct scale up to commercial operations. A pilot plant heater was constructed and tested to develop an understanding of the slurry heating process and to ensure that commercial scale heaters were appropriately sized.INTRODUCTIONPressure Leaching OperationsPressure leaching operations are often used to oxidise sulphide gold ores, or for extraction of nickel and cobalt from laterite ores with sulphuric acid. Where there is sufficient sulphur available, the exothermic pressure oxidation reactions can be self sustaining at temperatures as high as 225 ºC, without having to preheat the feed slurry. At lower sulphur levels, slurry preheating is required. This is typically achieved by utilising the flash steam released from the slurry letdown stages and contacting this directly with cold incoming slurry ahead of the autoclave. The vessels where this slurry-steam contact is made are known as heaters or condensers, with the number of pre-heat stages varying, depending on how much heat is evolved in the oxidation reaction (Mason, 1990).In nickel laterite pressure acid leaching processes, which operate between 245 and 270 ºC, the only significant exothermic reactions are those associated with dilution of sulphuric acid in the leach. As a consequence, slurry preheating with flash steam is always used commercially. In practice the number of flash steam preheating stages required varies from 1 to 3, driven by a number of factors, including other uses for flash steam and the upper temperature limit at which preheated slurry can be pumped. A diagram of a typical pressure acid leach train is shown in Figure 1.For pressure acid leaching operations and at low sulphur levels in pressure oxidation, boiler generated direct steam addition to the autoclave is required to sustain the reaction temperature. For this reason it is imperative that the flash steam – slurry heat transfer is efficient and the slurry temperature approaches that of the flash steam closely."

Jan 1, 2012

By C. Harold Riches

This article is directed co a commentary on the patent system in its relation to the public interest. As man gained supremacy over his environment, he could devote progressively increasing portions o his time to improving his standards of living. In the history of the human race, we have advanced from the hollowed floating log to the modern steamship of the present age; from the sickle and flail to the reaper and combine; from the trumpet and drum as a means of communication co the telegraph, telephone, and radio; from the horse and ox cart to the automobile, truck, aeroplane, and train; and so on ad infinitum through the list of inventions on which are based the industrial and political economies and standards of living we enjoy today. It has also been a long road from the day of the alchemist and his closely guarded secrets to the era of the patent system and its storehouses of knowledge open to the world. The alchemist and the craft and merchant guilds closely guarded their secrets. In fact, they largely opposed innovations on the grounds that they might injure profits and restrict employment. In these days of unrest, with great clamour out of doors for radical changes in our political and industrial economies, it may not be untimely to examine one of the keystones which support the economic structure we know as the free enterprise system, the system which is predicated upon the right of the individual to own property. Many, through impractical idealism, ignorance, confused thinking, or blind political prejudice, advocate the substitution of ownership by the State ? for the right of ownership by the individual. As civilization has advanced to the high standards of living we enjoy today through the efforts of a comparatively few inventors, the patent system which has provided the incentive that created the inventions on which our industries and our employment are based is fully understood and appreciated by a comparatively small percentage of our people. As a result, the patent system, as a keystone in our free enterprise economy, is an apt target for destructive criticism, with the thought, possibly, that by eliminating or drastically restricting the several rights to individual ownership one by one, ownership by the State will progressively replace ownership by the individual.

Jan 1, 1949

By M. Tadie, J. Wiese, K. Corin

The use of potential control in the flotation of ores has been applied in a variety of operations and presents an opportunity for improvement of selectivity and recovery of valuable minerals. Although it is possible to vary the redox potential (Eh) using chemical additives such as sodium hypochlorite or hydrogen peroxide this is more commonly done by varying the pH and dissolved oxygen (DO) concentration. The present study involves an investigation into the effect of varying dissolved oxygen concentration, ionic strength (IS) and pH on the flotation response with the aim of application to a South African lead-zinc ore. In all cases the Eh is measured as a function of the different DO, IS and pH values. The main objective was to achieve selective flotation of galena from sphalerite. The first part of the work was micro-flotation tests conducted on single minerals with galena used as the basis for effect of the factors studied on redox potential and ultimately recovery. The DO was varied by alternating between the use of air and nitrogen as the gas source to the micro-flotation cell. PH was varied between pH 9.2 and pH 11.8 using sodium hydroxide. In the first part of this study a factorial design approach was used to determine the interactive effects of the variables tested, viz. DO, ionic strength and pH, on the Eh and on the recovery. Redox potential was measured using a combination electrode made up of platinum wire and Ag/AgCl reference combination. Recoveries indicated that pH had the most significant effect on recovery and Eh. The influence of redox potential on recovery was found to be of relevance to the condition of high dissolved oxygen concentration and less so at low dissolved oxygen concentrations. It was also noted that that the combined interaction between ionic strength and dissolved oxygen concentration had a positive effect on recoveries, however this was not so with Eh. The chemistry of the ions in solution was observed to play a dominant role on the recovery due to changes in solubility arising to pH modification. The longer term objective of this work is to determine the optimal Eh conditions for the separation of galena from sphalerite.

Jan 1, 2016

By Bahjat Khoshaba, Bern Klein, Haixing Yan, Libin Tong, Andrew Bamber

"When a conductive or magnetic particle was put into an electromagnetic field introduced by an electromagnetic sensor, the particle can influence the electromagnetic field which can be used to characterize this particle. The electromagnetic technology based on eddy current theory was explored to investigate its potential in both the separation of minerals and the pre-concentration of a base metal ore. Samples tested in the study included the minerals obtained from Ward’s Science and the low grade copper ore particles obtained from Mount Polley Mine. The effects of mineral type, sensor frequency, particle size, particle position on the sensor surface, and particle lift-off on the magnitude and phase of the electromagnetic spectra were investigated. The electromagnetic spectra of various minerals show that it is possible to separate chalcopyrite or magnetite from tested minerals, simply based on the magnitude of the spectra. The spectra of the ore particles were determined by the mineral in the particles with the strongest signal. The effect of the pre-concentration of the low grade copper ore is determined by the association of chalcopyrite with magnetite. Direct sorting is the mechanism in the separation of mineral particles, while indirect sorting is the mechanism for low grade ores.INTRODUCTIONSensor-based sorting technologies include radiometric, X-ray transmission, X-ray fluorescence, near infrared, photometric, inductive, microwave heating and so on. Sorting not only discards barren rocks away from the concentrator but also recovers metal bearing that would be lose to the waste dump. The benefits of pre-concentration using sensor-based sorting are achieved on reduced energy consumption for comminution and reduced water usage on a volume per weight of metal basis (Bamber, 2008; Gunson, Klein, Veiga, & Dunbar, 2012; Kleine & Wotruba, 2010; Knapp, Neubert, Schropp, & Wotruba, 2014; Kobzev, 2014; Lessard, de Bakker, & McHugh, 2014; Mazhary & Klein, 2015; Robben, Wotruba, Robben, von Ketelhodt, & Kowalzcyk, 2013). Amongst others, high frequency electromagnetic sensors were developed for ore sorting at MineSense Technologies Ltd. and are subject of this paper. Improving the understanding of ore heterogeneity is the basis for developing a successful semi-bulk or bulk sorting systems by incorporating the sensors in the material handling equipment (MineSense Technologies Ltd., 2016). The present study focuses on the bulk sorting potential and bulk sorting mechanisms of the electromagnetic technology in the pre-concentration of minerals or ores."

Jan 1, 2016

"Virtual reality, a 3D computer-generated environment, has become a recognized delivery system for many forms of education. This paper describes the application of virtual reality to mineral processing education. An interactive mineral processing visualization module developed at the University of New South Wales, Australia, provides users with an overview of a base-metal concentrator and details about how the mined ore progresses through stages in processing. The module also involves developing instructional based plant layouts and flowsheets in the virtual environment. These assist the user in understanding the essential components of the base-metal concentrator.RÉSUMÉ La réalité virtuelle (RV), un environnement en 3D généré par ordinateur, est devenue un système de prestation reconnu pour diverses formes d’éducation. Cet article décrit l’application de la réalité virtuelle à l’éducation dans le domaine de la minéralurgie. Un module interactif de visualisation du traitement des minerais développé par l’université de Nouvelle-Galles du Sud, en Australie, offre aux utilisateurs une vision d’ensemble d’un concentrateur de métaux communs ainsi que des détails concernant la progression du minerai extrait à travers les différentes étapes de traitement. Ce module implique également le développement de schémas de réalisation et de traitement didactiques dans l’environnement virtuel, lesquels schémas aident les utilisateurs à appréhender les composantes essentielles d’un concentrateur de métaux communsINTRODUCTIONVirtual reality (VR) is the creation of an artificial environment that is experienced through sights and sounds provided by a computer (Squelch, 2001). The simulated environment is achieved through technologies such as 3D graphics, audio feedback, and special peripheral devices to produce interactive environments.Virtual reality has been used in diverse fields including medicine (Riener & Harder, 2012), entertainment (Hsu, 2011), military (Manojlovich, Prasithsangaree, Hughes, Chen, & Lewis, 2003), manufacturing (Zimmermann, 2008; Jiang, 2011), and chemical processing (Squires, Andersen, Reklaitis, Jayakumar, & Carmichael, 1992; Schofield, Lester, & Wilson, 2005). Virtual reality is also becoming the recognized delivery system for education in many fields, including engineering (Bell & Fogler, 1996, 1998; Shin, 2002). For example, VR laboratories have been designed and developed to teach users fundamental features of heterogeneous catalytic mechanisms and absorption columns (Bell & Fogler, 1995), the multi-phase and multi-component blast furnace iron-making process (Babich & Senk, 2009), and to guide users to identify various safety measures while working in a real laboratory (Bell & Fogler, 1996)."

Jan 1, 2017

By K. Sawamukai, S. Ogasawara, D. Umenai, T. Tsuruta

"Removal of cobalt, strontium or cesium ion from the aqueous solution containing each metal ion only using microorganism was examined. Arthrobacter nicotianae which had a high ability to remove cationic metal ion was used for the removal of each metal. The removal of cobalt, strontium or cesium using A. nicotianae cells was affected by the solution pH, concentration of metal ion, and cell amount. The effects of above mentioned factors on the removal of each metal and time course of strontium from the solution containing each metal only using A. nicotianae cells were reported in this paper. INTRODUCTIONRadioactive elements, such as cesium, iodine, strontium, plutonium, barium, cobalt, lanthanum, yttrium, and tellurium, were detected around Fukushima Daiichi nuclear power plant, which was damaged by the magnitude 9.0 earthquake and the tsunami followed.The removal of radioactive elements from contaminated sources is a worthwhile subject to investigatein terms of environmental control. Research efforts have been especially concentrated on studying microorganisms that remove uranium including bacteria (Andres et al, 1993, Hu et al, 1996, Marques et al, 1991, Strandberg et al, 1981), actinomycetes (Byerley et al, 1987, Friiss and Myers-Keith, 1986, Golab et al, 1991), fungi (Byerley et al, 1987, Galun et al, 1983a, Galun et al, 1983b,Tsezos and Volesky, 1981, White and Gadds, 1990) and yeasts (Strandberg et al, 1981, Schmate II et al, 1978).We have investigated removal and recovery of uranium from aqueous systems using microorganisms isolated from uranium mines. We identified some strains of bacteria with extremely high uranium removing abilities (Sakaguchi et al, 1996), and thus, the microbial biomass may be considered as an adsorbing agent for the removal and recovery of uranium and heavy metals present in aqueous systems around Fukushima Daiichi nuclear power plant.In the present study, we screened various species and strains of bacteria, actinomycetes, fungi, and yeasts for their ability to adsorb uranium (Tsuruta, 2002). Basic features affecting uranium adsorption?co-existing cations and anions, cell amounts, pH, and the adsorption time course?by Arthrobacter nicotianae cells, which adsorbed the largest amount of uranium, were also investigated. In addition, we examined the removal of an other actinoid element, thorium ion, which may be present with uranium in refining effluents.In this paper, the removal of cobalt, strontium, or cesium from the solution containing each metal ion using A. nicotianae cells is discussed."

Jan 1, 2012

By G. Granata, C. Tokoro, T. Kato

"The goal of this study was to evaluate the effectiveness of mechanochemical activation by planetary milling as method to enhance the recovery of cerium from rare earth ores. For this purpose, a weathered ore was first ground by planetary milling and then leached by sulfuric acid. The influence of planetary milling was investigated by assisting the experiments with X-ray absorption fine structure (XAFS) in cerium LIII-edge and inductively coupled plasma spectrometry to measure the concentration of cerium dissolved by leaching. Results showed that, by increasing the grinding time, although the particle size of the specimen increased due to agglomeration, the recovery of cerium significantly increased. This finding clearly indicated that a smaller particle size actually hinders the recovery of cerium. In particular, XAFS analysis revealed that the longer the grinding time, the more tetravalent cerium could be converted into trivalent cerium and such conversion, also called mechanochemical reaction was beneficial to the recovery of cerium. Based on the obtained results, it was confirmed that approximately 70% of cerium could be recovered by mechanochemically activated leaching of rare earth ores.INTRODUCTION Rare earth elements (REEs) are a group of 17 chemically similar metallic elements comprising lanthanides, scandium and yttrium. Since REEs have various unique physical and/or chemical properties, they have become essential materials for advanced application (Adachi, 2015). REEs used in industry are usually supplied as rare earth minerals. In the last decades, flotation, gravity separation, magnetic separation and leaching have been widely applied to recovery of REEs from rare earth minerals like monazite (Archana, Rekha, Manis, Jitendra, & Jin, 2015). Among these operations, leaching has been widely studied in the recent years to improve the state of the art (Archana, Rekha, Manis, Jitendra, & Jin, 2015; Xiao, Feng, Huang, Huang, Chen, Liu, Wang, & Long, 2016; Farzaneh, Fereshteh, & Ahmad, 2017). Aiming to enhance recovery of REEs from rare earth minerals, a possible advancement of leaching technology could be the mechanochemically activation of the ore by high-intensity milling (Alorro, 2016). In the mechanochemical activation, an improvement of the leaching performances can be achieved through high-intensity milling operations which result into a dramatic decrease of the mineral particle size with a consequent improvement of the physical kinetics of leaching. Furthermore, the high mechanical energy provided to the sample during milling can determine the rupture of the crystal structure of the mineral, thereby transforming it into a more leachable form."

Jan 1, 2017

By Shintaro Takamiya, Kazunari Yoshida

"Recently, small sized micro-needles for medical are required more frequently by patients. The biggest reason is that it presents great burden on the patients, due to the size of the needle injection. People need to use a very small needle to lower the pain, but the downfall is that it makes them more expensive due to their complicated manufacturing method. Therefore, we need to fabricate a needle by wire-drawing to decrease its price. Tube-drawing is beneficial for its production value; however, in conventional tube-drawing it is difficult of control the wall thickness of the tube and makes it 1mmor lower in diameter. That is why, we propose fluid-mandrel drawing for new tube drawing. This method allows fabrication of a fine tube by using the pressure of the fluid in the tube. In this research, the goal is the fabrication of a fine tube by fluid-mandrel drawing and its evaluation. Finally, the fabrication of a fine tube by fluid-mandrel drawing was conducted and in result a tube with a diameter of 0.2mm, high strength and thin wall and fine inner surface was drawn, which can be used as a lesser pain micro-needle.INTRODUCTIONThe main manufacturing method of the current medical needles is roll forming. With this method, it is difficult to make a tube with a diameter lower than 1mm. Deep drawing has been proposed and used as method to further reduce the diameter, but this method is costly and the injection needle obtained by this method is several times more expensive.Therefore, we need to obtain a fine medical needle by drawing process that can be mass-produced and inexpensively manufactured. However, with the conventional drawing process, it is not possible to obtain a syringe needle with a reduced diameter easily, that is why, a fluid-mandrel drawing has been proposed which can reduce the diameter without damaging the inner surface. The methodology of the method is, a fluid is filled in the sealed tube and the pressure inside the tube during drawing is responsible for the good inner surface and wall thickness. It is also expected that the fluid can be easily discarded and that the tube can be manufactured on a long scale."

Jan 1, 2017

By G. Vibert Douglas

IN a previous paper by Douglas and Gillies (1), a simple field test was given for gold. Later work by the present writers, and by others who have kindly written to us, shows that the test is not as satisfactory as it was hoped. In many cases, the gold mirror is completely obscured by a dense precipitate which, up to the present, it has been found impossible to remove. After many attempts, we have temporarily given up the iodine test and have been working on a simple pyridine reaction based on the work of Putnam, Roberts, and Selchow (2): The ore to be tested is ground to a fine flour. Place half a gram of this powdered ore (an amount that will cover a Canadian ten-cent piece, not heaped) in a six-inch test-tube and add 5 c.c. of aqua regia. The aqua regia. should be made up on each occasion, using four parts of hydrochloric acid and one part of nitric acid, both concentrated. Shake the solution in the test-tube for about one minute and allow to settle until dear. The rime to settle may be 30 to 60 minutes. When dear, a drop of the solution is with-drawn with a fine, dean eye-dropper or capillary tube and placed on à small glass plate. A slide such as is used for mounting rock sections is suitable. Now place an equal sized drop of pyridine solution on the plate beside that of the aqua regia solution to be tested. The pyridine solution, containing nine volumes of hydrogen bromide to one volume of pyridine, can be made up in advance and carried in a glass-stoppered bottle. Join the two drops with a glass thread or fine, dean stick, and allow the merged drops to stand undisturbed. I t is well to place the slide on a piece of white paper so that the presence of the crystals which may form can be easily seen. The time for their formation will vary with the amount of gold present, but the slide should be allowed to stand for at least 30 minutes before negative results are reported. A hand lens of at !east ten magnifications is essential. If gold is present, minute red crystals will form around the margin of the drops as these drops slowly evaporate.

Jan 1, 1938

By S. H. Lucas

"This paper describes the development and application of single-stage fluidized bed continuous ion exchange to the following processes: removal of base metals from mine water; cyanide removal from gold mill waste; uranium removal from sulphuric acid leach liquor; and uranium removal from mine water. IntroductionThe recovery of metals by fixed bed ion exchange has been practiced for many years. However, the operation has been semi-continuous and can only treat clarified liquors. Substantial savings could be made if the operation were continuous, thus reducing the resin inventory, and if the costly filtration and clarification steps could be eliminated. Work has been in progress over the past twenty-five years on the recovery of metals from unfiltered ore leach slurries, heap leach liquors and mine drainage waters containing a small amount of suspended solids. In the case of dilute waste solutions, with suspended matter and high flow rates, filtration is usually prohibitively expensive.Continuous ion exchange operation using fluidized beds has made it possible to reduce considerably the resin inventory and to allow the treatment of unclarified liquors and slurries. The subject has been reviewed on several occasions (1. 2. 3, 4). Although fluidized beds in multi-stage columns are an improvement over previous resin-in-pulp treatment, they have complicated internal structure and I or involved automatic control systems to move the resin stages.Slater and Prud'homme performed studies on multi-stage fluid beds, and concluded that the performance of single, deep fluidized beds of resin with continuous or semi-continuous flow of both phases would be worth investigating, particularly in the case of very dilute metal solutionsoi, A pilot plant was designed and built at CANMET in a cooperative project with Dr. Slateroi. The use of deep fluidized beds of resin (with a large height/diameter ratio) for treating dilute solutions has the attraction of engineering simplicity. Extreme simplicity of equipment design is considered of paramount importance when treating, for example, mine waters at high flow rates, possibly of the order of several million gallons per day. This paper describes the development of the concept of single-stage fluidized bed continuous ion exchange arid reviews the pilotplant development of processes for the treatment of base metal mine water, cyanide waste water, uranium leach liquor and uranium mine water."

Jan 1, 1980

By H. C. L. Reemeyer

One of the fundamental trade-offs for copper concentrators is between grinding circuit product size and copper recovery. The capital and operating cost savings and throughput increases for a coarser grind should be evaluated against potential recovery reductions. Other benefits of coarser grinds, such as GHG emissions reductions and favourable effects on tailings and water management should also be considered. This paper assesses the formation of laboratory and pilot test programs, design of process flowsheets, equipment selection, and evaluation methods to determine the most appropriate and economical grind size for a given deposit. The paper will include an evaluation of case studies. INTRODUCTION The majority of the world’s mined copper comes from sulphide deposits, which are mostly processed using crushing, grinding, flotation and dewatering flowsheets to produce copper-bearing concentrates for smelting. Ores must be ground to a sufficiently fine size to achieve an acceptable level of liberation to allow both high recovery of copper and valuable by-product minerals while efficiently rejecting gangue to tailings. Therefore, a key design parameter in process plant design is the grind size of the flotation feed. Copper concentrators use a variety of grind size targets that depend on various factors, including ore mineralogy and the grain sizes of valuable and gangue minerals; the sensitivity of valuable mineral recoveries in the rougher flotation stages to grind size, ore hardness; electricity costs; and mining vs. processing throughput constraints. Typically, copper and by-product recovery increase as grind size is reduced, which can improve revenue, but finer grinds increase power and grinding media operating costs and may have implications for tailings management. This paper explores the trade-offs that should be assessed in determining the optimum grind size, and to answer the question if coarser grinds are worthwhile. METALLURGICAL AND FLOWSHEET FACTORS Recovery-by-size behaviour of sulphide-bearing particles In base metals sulphide flotation, it is typical that flotation recoveries vary by particle size. Metal sulphide particles rendered hydrophobic by collector in intermediate size ranges (e.g. 10 to 100 um) usually show very high recoveries, often approaching 100%. Recovery usually falls away in finer size fractions (<10 um) as fine particles have little inertia and can move around bubbles without colliding and attaching to them. Coarser particles (>100 um) are susceptible to particle-bubble detachment and dropback (Jameson, 2019).

Jan 1, 2019

By T. Yameogo

Many ideas, tools, technologies, and methodologies are believed to have staked their claims on the future of mining. For example, automation is strongly positioned as the platform within which mining will be practiced. A subset of automation ? intelligent mining ? will add some smart interactions between machines, technologies, the rock, and the environment. The future also calls for an improved approach to sustainability and corporate social responsibility. Mines of the future are dreamed of to be more ethical and more balanced. They will boast optimized designs, integrated value and supply chains, produce less waste, recycle and reuse, and will require less energy to operate. Then, what about the people that will operate this optimized ecosystem? How is the education system teaching the operators of the mines of the future? What kind of a future should mining education foresee to prepare the workers appropriately? In recent years, the shortage of skilled labor for mines around the world has created a tough competition to attract, retain, and train the very people without whom mining will cease to exist. In Australia, Canada, and the United States in particular, the war for talent has resulted in higher-than-usual labour costs. Such costs have dented the unit costs of many mining businesses. Concomitantly, mining contractors? and consultants? prices have increased to reflect the escalation of labour costs across the value chain. From labourers to engineers, from juniors to seasoned professionals, the increase in compensation is unprecedented. Yet, the shortage is still hurting the industry, and the high calibre candidates continue to be rare gems. The industry has been implementing aggressive solutions that include the increased hiring of skilled immigrants, the training and recruitment of minorities, and the retaining of near-retirement experienced employees. Public relation campaigns about the benefits of embracing careers in mining are also common. The CIM has also devoted a ?M4S? section to its pan-Canada meetings to educate the public, especially the youth, about the importance of the mining industry for Canada. Moreover, mining associations and universities are enticing students? enrolment through scholarships and financial support. Still, the balance between quantity and quality of workers can be discussed. This paper intends to discuss the present state of mining education as an essential part of the future of mining. The authors brush the picture of the education of miners, technicians, and engineers, against the backdrop of the technology-advanced mines of the future.

Aug 1, 2013

By J. X. Guo, A. Pindred, J. Moore

"Two modified centrifugal flotation cells (CFC), Q2 and Q3 models, have been developed for froth flotation. The operating mechanism of Q2 uses a rotating bowl to create a centrifugal force on the feeding slurry. Froth concentrate is collected on the central top of the cell and tailing is discharged along the top edge of the rotating bowl. The Q3 utilizes a vertical rotating feed pipe to introduce the feed slurry into a stationary flotation column cell. A centrifugal force is also created by a rotating pipe for the feeding slurry. Froth concentrate floats over the cell and tailing discharges through the bottom of the cell. The centrifugal force causes the flotation recovery of fine particles from CFC to be higher than from the conventional cell. The major operating variables of CFC are the rotating speed, air flow rate into feed slurry, and slurry feeding rate etc. Flotation tests have been carried out on synthetic mixtures of galena-silica and chalcopyrite-silica, as well as some natural base metal ore samples. Parallel tests were also conducted on a conventional flotation cell. The comparative test results demonstrated that both Q2 and Q3 have the advantage of higher recovery of finer than 10 µm mineral particles, which are very difficult for the conventional non-centrifugal flotation cell to recover. The grade-recovery curves produced from CFC are equivalent to or better than the conventional flotation cell. There is a potential in the future for the CFC to be employed in slime flotation.1. IntroductionA centrifugal flotation cell (CFC) was originally developed by Clean Earth Technologies [I] to separate oil from water and was subsequently applied in froth flotation. Figure 1 illustrates the design of the original CFC, in which a vertical feeding pipe is attached to the center part of a rotating drum and a stationary shell encloses it to direct the float froth and tailing discharge. The slurry flows down to the bottom of the spinning drum, gets in touch with a screen of air bubbles and then migrates outwards under the effect of centrifugal force. After the mineralized froth enters the rotating cell, it is pushed back to the inner surface. The overflowing froth is collected in the froth launder while the tailing slurry is discharged through orifices along the outer rim of the drum."

Jan 1, 1998

By R. Sharma, I. Miskovic, S. Miskovic

Solvent extraction (SX) is a widely used method for the extraction of copper from pregnant leach solutions or other ionic solutions in hydrometallurgical applications. About 17% of total refined copper production worldwide is produced using SX followed by electrowinning (EW). Conventional SX units, such as mixer-settlers, consume a large amount of extractant, offer poor process control and yield low extraction efficiency. Extraction efficiency is poor due to low specific interface area, crud formation, emulsification, and slow phase separation stage. Micro solvent extraction (micro-SX) is a rapidly developing technology that provides an opportunity for improved process control, higher extraction efficiency, lower residence time and, as such, has a potential to reduce the environmental footprint of SX operation. In this research, extraction of copper ions in an acetate buffer media is investigated using D2EHPA with kerosene as a diluent. Chemical factors such as extractant concentration and ionic concentration of aqueous phase are varied to determine the optimum conditions. Subsequently, the extraction efficiency and reaction time of new micro-SX reactors are compared against previous bulk SX studies. Extraction in the microfluidic reactor was observed to be faster with a residence time more than an order of magnitude lesser than bulk SX. This study forms a prelude for developing new modular micro-SX units which will enable continuous, effective, and safe operation on a large scale. In future studies, numerical and analytical models validated through this work will help eliminate rigorous experimentation and enable faster design and fabrication of micro-SX units. INTRODUCTION Conventional industrial solvent extraction (SX) units such as mixer-settlers, extraction columns present various disadvantages. Low specific interfacial area, crud formation, and emulsification in industrial reactors lead to long extraction times and severely hamper extraction efficiency (Priest et al., 2011; Chen et al., 2017). Microfluidic extraction considerably improves upon the current extraction practices by (1) creating a large surface to volume ratio that enables rapid mass transfer across the interface, (2) better process control, and (3) easier separation of phases (Kashid, Renken, & Kiwi-Minsker, 2011; Ciceri, Perera, & Stevens, 2014). These factors establish micro-SX as a crucial mode for process intensification. Although, a micro SX unit has significantly low processing volume than conventional extraction methods, their throughput can be increased via massive parallelisation (‘numbering up’), which is an area of active research (Darekar, Singh, Mukhopadhyay, & Shenoy, 2016a; Kriel, Woollam, Gordon, Grant, & Priest, 2016).

Jan 1, 2019

By G. Stokreef, B. R. Davis, M. Kadiyski, T. LeBel, Alvear Montenegro, R. Parra, V. Montenegro

A drop tower and methodology were developed to study the impact of mineralogy on the flash combustion behaviour of copper concentrates. Reaction shaft conditions of a flash furnace were simulated using a drop tower reactor and different molar ratios of oxygen gas to sulphur in the feed. Five feeds were tested in the drop tower including pure minerals chalcopyrite and pyrite as well as two mineralogically distinct copper concentrates and a blend of the two. The behaviour of each of these five feeds were evaluated through analysis of the solid combustion products for elemental sulphur, mineralogy and particle size. Desulphurization curves for each of the feeds were produced. It is thought that the desulphurization behaviour of pure minerals can be used to estimate the behaviour of a concentrate and that a blending recipe could be developed, which can optimize the chemical and mineralogical inputs to the flash furnace and guide operations on the optimum furnace conditions. Overall, the drop tower has proven to be a useful tool for studying flash combustion processes. Experimental results suggest that mineralogy has a significant impact on the conditions required for the production of matte with consistent grade. This finding is especially significant for custom smelters, which may see several different blends in a day. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process that is used to produce copper matte from copper sulphide concentrates. Dried concentrate(s), silica flux, and secondary materials are blended to a target chemical composition, typically given by the Cu/S ratio, before processing. This fine, dried feed is dispersed throughout the heated furnace reaction shaft with an O2-enriched reaction gas. The particles heat up in the shaft of the furnace, ignite and undergo reactions that pre-oxidize the iron sulphide and some of the impurities in the feed. Oxidation reactions in the shaft of the furnace desulphurize the feed and produce an SO2-containing off gas. The reacted particles fall into the furnace settler and separate into a Cu-rich matte and an iron-silicate slag, while the SO2-containing off gas is carried out of the furnace for heat and dust recovery, as well as H2SO4 production. Some concerns during operation of the furnace are dusting, over or under oxidation of the feed, and a stable flame.

Jan 1, 2019

By C. Matthews, A. Vo

Australia is one of the world’s leading exporters of bulk commodities and the extensive use of sampling equipment is key to the successful management of each mining operation. At the process plant, without a full understanding of the feed, product and tails, it is impossible to fully optimise the performance of the plant, such that the metallurgical balance is often open to error. At the port, a statistically correct, bias free and compliant sampling system is crucial to ensuring exported minerals are reflective of their true value and to avoid penalties. Over the last decade, as a result of the iron ore boom, there has been high demand for reliable, representative and standard compliant solids sample systems in Australia. This paper reviews several solids sampling applications at Australian mine sites, the challenges and experience gained and how the implementation of reliable representative sampling systems has provided better understanding of plant process performance, improved plant control and overall benefits to the operations. INTRODUCTION Mining is the primary contributor to the Australian economy with Australia ranking in the top 4 in economic resources for 21 primary industrial minerals in 2016 (Britt, et al., 2017). Australia is one of the world leaders in the export of the majority of its commodities including gold, copper and iron ore (Britt, et al., 2017). Therefore, a suitable and standard compliant sampling system is essential for evaluating plant performance and content verification. At the mine and at the port, the larger iron ore miners in Australia have developed stockpile models to predict the grade of their ore down to individual blocks of the stockpile. This allows the miner to create the right blend of material for sale to their customers and ensures they are not underselling their product or at risk of penalties for impurities or low grade. As an example, the average difference between the benchmark 62% Fe and low grade 58% Fe fines at the time of this report averaged US $20/tonne according to the Metal Bulletin Iron Ore Index (Fastmarkets MB, 2019). At a shipload of 180kt this would be a variation of US $3.6M. Whilst this is an extreme example, it highlights the economic importance of producing the correct grade product and a recognised representative sample of said product.

Jan 1, 2019

By Zhang Wei

"Pulang Copper Mine is located in Shangri-La county, Diqing Prefecture, Yunnan Province, with currently defined copper reserve of 4.8 million tonnes of copper metal and an average grade of 0.34% Cu. The mineralized zone in a dome shape is 2,300 m long, 600–800 m wide, and 1,000 m high. At present, the project is at a construction phase, with a first-stage mining and processing capacity of 12.5 million tonnes of ore per year. Ore haulage is planned via a drift and ore pass development system. The cavability of mineralized rock is classified into three types (II, III, IV), with type III accounting for more than 98% of the total reserves. The cavability of the orebody is generally considered to be good and block caving mining method is planned. Semi-autogenous grinding and ball milling are adopted for the mineral processing. The tailing dam construction method is a center-line method.INTRODUCTIONAs the China's largest underground nonferrous mine, Pulang Copper Mine is located in the northeast of Shangri-La County, Diqing Prefecture, Yunnan Province, China. It is 62 km northeast of Shangri-La city. Shangri-La County is a Tibetan-dominated, multiple-ethnic region, with a population of approximately 163,000 in 2009. The county is rich in mineral and water resources, thriving with tourism. Its economy is also dominated by agriculture. To date, the defined copper reserves at the Pulang Copper Mine is 4.8 million tonnes of copper metal at an average grade of 0.34% Cu. In addition, it contains a gold reserve of 145 tonnes, a silver reserve of 2,754 tonnes, a molybdenum reserve of 0.19 million tonnes, and a sulphur reserve of 10.5 million tonnes. The first-stage mining and processing capacity is planned at 12.5 million tonnes of ore per year. When it ramps up to this production rate, the mine will produce copper concentrate containing 50,000 tonnes of copper and molybdenum concentrate containing 968 tonnes of molybdenum. A drift and ore pass system is planned for ore haulage and mining method is a block caving method. Semi-autogenous grinding and ball milling are considered for mineral processing. A center line dam is adopted for the tailing dam construction (Feng, 2010; Feng, Li, & Wang, 2011; China Enfi Engineering Corporation, 2014)."

Jan 1, 2016

By Jean-François Lagueux

Goldex Mine is an underground mine located near the town of Val-d?Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long hole stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23 Mt of ore, large blasts up to 1.8 Mt are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km radius of the mine site. In addition to managing mass blasts, means must also be found to mitigate the vibrations produced by the blast to diminish the disturbance to the neighbourhood. Therefore, the mine used numerous tools to properly plan the blasts and reduce the impacts. A program to control vibrations was one of the first tools put in place. The program?s aim was to draw up an action plan to ensure a follow-up of the homes by inspecting them. The second tool was to develop a methodology to plot a reliable attenuation curve and to adequately determine the maximum charge weight for each blast. Finally, effective communication tools were developed to inform the neighbourhood. There was a huge amount of work to be done in relation to the bench. Reliable and fast loading techniques had to be found to load large blasts in a very short period of time. Adequate logistics had to be developed to send underground more than 20,000 kg of emulsion per day while performing the daily underground operations. Technology had to be developed to adapt the i-kon electronic blasting system to large blasts. Since the control of the charges was the major factor to reduce surface vibrations, it was important to employ loading techniques that would permit decking of the long holes to reduce the charge weight per delays without adversely affecting the loading. All of this work requires an enormous amount of energy but also close collaboration between the different stakeholders (various departments, suppliers and consultants).

May 1, 2011