Search Documents

By L. Contretras

This study has as an objective to analyze and to propose actions to improve the quantity and quality of the graduate education in the area of mining industry, specifically of mining engineers, metallurgists, geologists, to satisfy the expectations of professionals in the mining industry. Included are an analysis of the present scenario and the future demands in countries like Chile and proposed plans for the Establishment of Educational Initiatives, country policies and market forecast, vis-a-vis the experience of Australia, South Africa, United Kingdom, Canada and the United States of America.

Jan 1, 2007

By S. Mamonov, V. ?shikhin

"The purpose of work was the significant increase of copper recovery from slag at a concentrating plant. Analysis of study of slag phase composition showed the perspective of a slow slag cooling method due to its recrystallization and transition of primary copper minerals to secondary.Copper content in base slag varied between 0.71 and 0.96%. The study of a degree of copper minerals release of the slowly cooled slag in comparison with a yielding slag showed that in a flotation size grade –0.071 mm of yielding slag the weight ratio of released copper minerals grains is 58.95% against 86.73% in samples of slowly cooled slag. The process flotation sheet consists of three main, one control and two cleaner flotation operations with aftergrinding of middling products. A reagent mode was differed from a factory one by decreasing the slurry pH from 11–12 to 8–9. This paper shows research results of the slurry alkalinity impact on technological indexes of beneficiation (flotation).Industrial testing of a resulted batch of slowly cooled slag at “SUMZ” concentrating plant showed the efficiency of such processing: copper recovery to a copper concentrate increased by 15–19%.INTRODUCTIONIntensive development of mining and metallurgy industries within a 250-year period in the Ural region led to forming of approximately 315 man-made mineral formations at the territory of the Sverdlovsk region. The region contain over 32.5 billion tons of barren rocks and out of balance ores, over 1.5 billion tons of tailings, over 115 million tons of slimes, and over 100 million tons of metallurgical slag (Demin et al., 2000). Latters, at average, contain 407 thousand tons of copper, 2519 thousand tons of zinc, 7 tons of gold, and 150 tons of silver (Rudoy et al., 2011). Wastes generated in mining processing and metallurgical sector of economy contain not only thousands tons of copper and zinc, but cause significant damage to the environment where they are located. The reduction of negative impact of anthropogenic wastes on the environment as well as the storage volume reduction of valuable metals from dump slags is possible by improving the efficiency of the melting and further flotation of slags formed during this process."

Jan 1, 2016

By Madaah Hosseini H. R., P. Abachi, S. Miraghaei

In this study, the effects of milling time, chemical composition and heat treatment on microstructure and magnetic properties of nanocrystalline Fe-Si (6.5-25 at.% Si) alloys prepared by mechanical alloying have been investigated. The results show that increasing the milling time or the Si content, decreases the lattice parameter and increases the internal microstrain. The prepared powders mainly consist of micron-sized particles with an average grain size of less than 20 nm. The specific saturation magnetization values are slightly less than those of single crystal or conventional Fe-Si alloys and decrease as Si content increases. The coercive force values of the nanocrystalline as-milled powders are much higher than those of corresponding Fe-Si bulk alloys with a minimum at 13.5 at.% Si. The values of coercive force decreased after annealing but it seams that the residual strain developed during milling is not the major contributing factor to the higher values of coercive force in the mechanically alloyed powders and nanocrystals behave as single-domain particles without exchange interaction between them.

Jan 1, 2006

By J. Doucet, C. Price

In an industrial setting, operational changes are continually introduced, driven by new technologies or changing economics. Because of day-to-day variability, quantifying the impact of these changes based on metallurgical performance requires long trial periods to achieve statistically significant results. Tools and techniques developed by the mineral processing group at McGill University have allowed for direct measurement of process variables (e.g., bubble size, gas and solid holdup). Two case studies are described where direct measurement techniques were used to evaluate: a) a new rotor stator mechanism; and b ), the introduction of a new frother type. Application of these methods has accelerated the evaluation of process changes and improved confidence in results.

Jan 1, 2009

By R. C. Reed, L. T. Wu, H. C. Harada, K. Kawagish, R. T. Wu

Oxidation of pure metals is a chemical reaction in which the metal loses one or more electrons, such that the atom of the metal changes from the neutral state to a positively charge ion and reacts with oxygen to form an oxide of the metal. The oxide can form as a protective and adherent scale that slows down further oxidation, or may spall off repeatedly, exposing fresh metal surface to react with oxygen. In multi-component alloy systems such as typical high temperature NiCrAlY bond coats, more than one oxidation mechanism may take place at once and thus, complicates the study of oxidation. To better understand the competition between formations of oxides of different compositions, a thermodynamic assessment is carried out to study the oxidation mechanism of a Ni-27Cr-9Al (at %) ternary alloy. Based on the assessment, it is demonstrated that the layering of different oxides can be determined, with the most stable oxide (alumina) existing directly above the metal-oxide interface and the least stable oxide (nickel oxide) locating on the outer most layer. A comparison between the calculated results and previously published experimental observations shows excellent agreement.

Jan 1, 2010

By A. McLean, A. Hue, K. Le, Y. D. Yang, P. Wu

While the treatment of relatively inexpensive ferrosilicon alloys is a potential refining route in order to generate solar grade silicon, phosphorus is one of the more difficult impurities to remove by conventional processing. In this project, the use of an electromagnetic levitation technique was used to investigate the dephosphorization of ferrosilicon alloy droplets exposed for various times and temperatures to a hydrogen-argon gas mixture. It was found that approximately 40% of the phosphorus was removed from an 85%Si-15%Fe alloy after 20 minutes exposure at approximately 1673K, to a gas mixture containing 48.5% hydrogen. Further dephosphorization is expected with longer reaction times. The effect of increasing temperature was found to be insignificant, although processing at lower temperatures is not only economically advantageous, it also decreases evaporative silicon losses, thus resulting in a more efficient process.

Jan 1, 2015

By O. J. C. Runnalls

"Canada became the world's largest uranium producer in 1984. That leadership position is likely to be maintained for many years into the future because of a firm production base, many undeveloped known deposits with commercial promise, and a large geologicalpotential for new discoveries.There are some uncertainties on the horizon, principally because of restrictive actions in process within the U.S.A., which are aimed at preserving a deteriorating domestic uranium industry. Should such actions result in import restrictions, for example, there would be a negative effect on foreign producers at least in the short term. Canada may avoid such difficulties under a tentative U.S.-Canada free-trade agreement where restrictions on the import of Canadian uranium into the United States would be eliminated. Over the longer term, demand for Canada's uranium resources will grow because of the foreseen growth in the world's installed nuclear power capacity. IntroductionSince the phenomenon of nuclear fission was discovered in 1938, the utilization of uranium has grown substantially. Initially, the principal use for uranium was in the production of nuclear weapons. However, once civilian nuclear power reactors began to be built in the 1950s, an increasing fraction of uranium output was directed to the production of fuel elements for use in electricity generating stations.The cumulative uranium production by those countries in the World Outside Centrally-Planned-Economies Areas, WOCA, during the period 1938 to 1985 exceeded 800 000 tonnes of uranium. Some 60% of that was mined in the United States and Canada, as indicated in Figure 1. In 1986, nearly 80% of WOCA output came from five countries, Canada, United States, South Africa, Australia, and Namibia, as indicated in Table 1 and illustrated in Figure 2.During the past decade the world annual consumption of nuclear energy has more than tripled (Fig. 3). As of December 31, 1986, the world total of nuclear power reactors had reached 394 with a total net capacity of 270 GWe. The thermal output from nuclear power plants in 1985 exceeded 60% of the energy contained in all of the oil produced that year in the Middle East. Thus, nuclear power has already become an important component in the world energy supply picture."

Jan 1, 1988

By Long Han, Beijing General Research Institute of Mining and Metallurgy, Yu Xie, Yunhai Zhang, Yangge Zhu, University of Science and Technology Beijing, Yanbo Shang, Xingrong Zhang

"The first-principles method was employed to study the adsorption of hydroxyl calcium (CaOH+) and hydroxyl (OH-) on hematite and quartz surfaces. The calculation results suggested that OH- preferred to interact with the active Fe sites on the hematite surface, whereas OH- adsorbed on the quartz surface by weak hydrogen bond. Though CaOH+ could easily adsorb on the hematite and quartz surfaces by the formation of Ca-O bond, the covalence formed on the quartz surface was apparently stronger than that on the hematite surface, meaning a stronger and more stable adsorption. CaOH+ adsorbed on quartz surface was mainly through the interaction of O-2p and Ca-3d states, and this interaction on hematite surface was weaker.INTRODUCTIONIron Increase and Silicon Reduction Technology (Yu & Duan, 2002) of hematite is mainly through the reverse flotation (silica is floated away from the iron concentrate). There are two ways to achieve this (Houot, 1983). One is to collect quartz by cationic collector directly; the other is to activate quartz by lime and then collect it by anionic collector. There are two main different views with respect to the mechanism of quartz activation: mono-hydroxyl compound theory (Fuerstenau, Rice & Somasundaran, 1965; Fuerstenau & Palmer, 1976) and surface hydroxyl precipitation theory (Hu & Wang, 1988; Wang & Hu, 1990). The former indicated the formation of the mono-hydroxyl complex is one of the two criteria of quartz flotation. The later theory, on the other hand, suggested that surface precipitation is the adsorption of active species of metallic ion on quartz surface. However, most of those researches are based on the solution chemistry of flotation and little is done at the microscopic level.In this paper, by the help of first-principles calculations, the adsorption models, bonding conditions, Mulliken charge populations and adsorption energies of hydroxyl and calcium hydroxyl ions (OH- and CaOH+) on hematite (001) and quartz (100) surfaces were investigated to find out the lime activation of quartz at atomic level, which is significant for the researches of quartz activation theoretically and practically."

Jan 1, 2016

By Sadough vanini Ali

Charpy impact energy of functionally graded steels produced by electroslag remelting in crack divider configuration has been modeled in various strain rates. It has been well known that majority of materials indicate different behaviors under different strain rates and temperatures. Therefore, modifying the elastic-plastic model considering the effects of strain rates and temperature gives us an acceptable prediction of these composites behaviors in impact test. In this investigation, graded steel was divided in to several layers in which the layers have the same strains under the impact. Constitutive equation describing the flow stress variations as a function of strain rates and temperatures, have been used to express the stressstrain behavior of layers. The parameter values of constitutive equation determined for all the layers via using the boundary conditions based on composite graded behaviors which were the characterized ferrite, austenite, bainite and martensitte phases. Consequently by applying the rule of phase mixtures and ascribing the impact energy of each layer to the area of stress-strain curve of the same layer, the whole impact energy of composite is the sum of layers impact energy with considering the layers volume fraction.

Oct 1, 2011

By P. B. Demarsh

"Location: - On highway 59, 17 miles east of Val d 10r near junction of Montreal highway in Northwestern Quebec.Life; - Started production 1952, ceased 1965.Ore: - Pyrite, chalcopyrite and small amounts of free gold and goldsilver tellurides in narrow quartz-carbonate-tourmaline veins in granodiorite. Specific gravity 2, 70.Capacity: - 700 tons daily Bevcon ore supply, l 000 tons daily when custom ore available.Assay: - Heads 0 .140 oz. per ton; tails 0. 009 per ton; extraction 92.5%.Grind: - 75% minus 200 mesh at 700 tons; 68% minus 200 mesh at 1000 tons. Detention time 28 hours and 21 hours respectively.Treatment: - Cyanidation process.Reagents: - Per ton. Aero Cyanide (NaCn) 0, 50; crushed unslaked lime 1. 75; zinc 0. 03; litharge 0. 10; steel consumption 2. 25.Water: - Pumped from land-lock spring fed lake l 1/2 miles distant.Cost: - Per ton. Crushing 0. 13; grinding 0 .32; filtration 0. 07; cyanidation 0.14; miscellaneous 0.29; total 0.95.Power: - Hydro-electric, 25 cycle, 12, 000 volts reduced to 550 volts.Labour: - Predominantly French Canadian, nucleus English Canadians.Tailings: - Impounded low lying pond.Personnel: - 15 including supervision.Flow sheet: - Canadian Mining Manual l 9 5 6 .Building: - Wood truss construction: 3/ 4 in. siding, ten test and 1/ 4 in. transite outside. Corrugated galvanized iron roof. Ground level foundations. Internal self induced heating. Wood stave tank equipment."

Jan 1, 1966

By S. A. Sadough vanini

In this paper, Stress-Strain-Temperature relations for Shape Memory Alloys are studied. Temperature effects on Shape Memory Alloys are different from those related to ordinary materials. In ordinary materials, elastic characteristics can be assumed to be constant in low temperature ranges, and only the deflection arising from temperature changes could be added to the elastic defection. As long as two phases of austenite and martensite could be present in Shape Memory Alloys simultaneously, elastic modulus follows temperature and temperature gradient. In continue a smart actuator is investigated considering a homogeneous cantilever beam. Beam bending is established by using shape memory wires. An initial strain is imposed to shape memory wires in a low temperature, and then, they are installed in the outer surface of the beam. Therefore, since the temperature is imposed in these wires and they cannot have free recovery strain, the compressive recovery stress will be produced in the outer surface. This will result in a deflection in axial direction of the beam. At first, beam deflection is calculated on the basis of theoretical relations and solving the relevant differential equations. Afterwards, experimental tests are performed on an elastomeric beam equipped with shape memory wires. When a voltage is applied, a temperature rise will occur in the wires; then, this temperature rise causes a deflection in the beam. Finally, the theoretical and experimental results? comparison indicates a good conformity. One capability of this actuator is its high flexibility, and by controlling the inlet current, the end-beam deflection can be controlled.

Oct 1, 2011

By Brian Lewis

"IntroductionThe leaching method selected for the dissolving of uranium ore depends in part on the physical characteristics of the ore, as well as the uranium mineralization. There are two main methods of leaching employed in uranium circuits in North America, one being ""Carbonate Leaching"" on sandstone, and pitchblende type ores, and ""Acid Leaching"", on quartzite type ores.This chapter deals with the acid leaching of uranium ores found in the Elliot Lake area, using sulphuric acid, for the leaching reagent, and ""pachucas"" for the contactor.The basic leaching process involves the pregrinding of the ore and the mixing of the ore with hot sulphuric acid, the mixture is air agitated, the air being used to oxidize the ore as well as produce agitation. The chemical reaction is as follows: Uranium Oxide + Sulphuric Acid = Uranyl SulphateThe following equations show the actual dissolution of the ""Hexavalent Uranium"", which show that more than one ion or complex of uranium is possible.Uranium DissolutionsI. UO, + 2H-(UOJ + H,O2. (UO,) + SO, = -UO, SO, (Uranyl Sulphate)3. UO, + SO,-(UO, (SO,),)=4. (UO, (SO,),)= -(UO, (SO,),)'Test work carried out in the laboratory as well as in the plants has determined the most efficient methods of extracting the uranium from the ore. A very important factor that has to be determined during initial test work are the amount of acid consumers in the ore. Within the Elliot Lake orebodies are minerals such as chlorite schist, diabase, and basement material, all very high acid consumers, consuming up to 1000 lbs. of acid per ton of ore. Of these minerals only the chlorite schist contain any uranium at all.The following are the operating parameters that have to be controlled in the plant:I. sulphuric acid concentration2. temperature of the mixture3. agitation4. liquid solid ratio5. reaction time6. particle size of ground ore"

Jan 1, 1989

By Gordon F. Scott

This paper considers a recently completed hoist project for IAMGOLD. Called the Westwood project, this mine utilises some of the largest drum hoists supplied to the North American Market in recent times. This project is an example of where many of the design features discussed the associated paper, (Robotham, 2011) were incorporated. Director of sales and marketing, Gordon Scott has worked at DavyMarkham for over 30 years in a variety of roles starting as a mechanical design engineer, moving to project management before joining the sales department. Gordon has an honours degree in mechanical engineering from Leeds University.

May 1, 2011

By Ahmad Abdollahi

Many factors affect mechanical properties of hypoeutectic Al-Si alloys. As examples the presence of impurities such as Mn and Fe due to the formation of intermetallic phases, additions of small amounts of alkaline earth metals and cooling rate in consideration of Si formation, they all have an impact on mechanical properties of hypoeutectic Al-Si alloys. In this investigation, the effect of Fe content into the specification range of A357 alloy, the addition of different modifiers consisting of Na, Sr and Ca for the alloy of A356 and different mounting techniques for separately cast test coupons of hypoeutectic Al-Si alloys using the lost wax method were studied. The results showed that using material with lower Fe content and addition of modifiers improve mechanical properties. Also different mounting techniques resulted in different mechanical properties.

Jan 1, 2004

By T. G. Carter

"During the early part of the 1980s, four new surface coal mines commenced operation in the Province of British Columbia. Each represented a major investment in both persons and materials in order to protect this investment in one significant area-the fixed portion of the surface coal handling system-a substantial amount of work was undertaken to ensure that the system was well protected from an outbreak of fire. A great deal of effort in this field had already been made by those coal mines which had been in operation for a number of years and experience gained at these operations was utilized in determining the level and extent of fire protection for the new mines.This paper summarizes the major problems, and suggests some of the methods of solution, in providing an adequate degree of fire protection for surface coal handling systems. It will also discuss the potential for gas and dust explosions together with ways to minimize this potential.The Fixed Coal Handling SystemNote: The word ""fixed"" has been used in its present context to denote that part of the coal handling system where the coal is moved via fixed installations such as a conveyor. It differentiates from that part of the system where coal is moved by mobile equipment.The raw coal delivered to the truck dump will undergo two major processes on its way to the rail load out. The first will be at the coal preparation plant where coal of specified quality will be extracted from the raw feed to the plant. If this coal is of metallurgical quality, and sometimes if it is of thermal quality, it will pass through a thermal dryer where part of the moisture acquired during coal preparation will be removed, i.e. the second process. As the complexity of both the coal preparation plant and the thermal dryer is such as to warrant separate considerations they will not form part of this paper. Each of the processes, however, is generally, housed in its own building, thus, containment of any hazards is usually more attainable than those existing or caused in the rest of the system."

Jan 1, 1988

By Tom Shumka

INTRODUCTION ?The Electro-Magnetic Crack Detection (EMCD) technique is an electromagnetic inspection method used for detecting and sizing surface breaking flaws. ?It works well on structural material or welds, ferrous or non-ferrous metals. ?EMCD?s rapid scanning is achieved using a hand-held probe. ?EMCD provides reliable crack detection and sizing (length and depth). Cracks can be sized accurately. ?EMCD dramatically reduces most cleaning requirements as there is no need to clean to bare metal. ?EMCD is capable of inspection through thin metallic coatings, or through non-conducting coatings up to 10mm thick. ?EMCD allows full data storage for back-up, off-line view and audit purposes.

Oct 1, 2010

By G. Morin, F. Chiesa, B. Tougas, B. Duchesne, Jocelyn Baril, N. Giguère

"An aluminum A356 compressor impeller was sand cast using the Low Pressure technique. The casting was limited in size (170 mm in diameter, 1.2 kg in weight) and very intricate in shape thus making 3D mold printing particularly favorable; indeed, producing this part by the traditional pattern-core box route would involve mounting 12 cores inside the mold while stringent dimensional tolerances are required as the impeller blades are only 2 mm thick. Consequently the molds were produce on the X-One MFlex printer of Quebec Metallurgy Center - CMQ. A dozen castings were produced with different casting temperatures and filling times so that it was possible to assess under which conditions complete filling of the mold cavity would be achieved. Filling and solidification modeling allowed predicting misruns and metallurgical properties inside the A356 (AlSi7Mg04) casting.INTRODUCTION Recent advancements in additive manufacturing enable foundries to produce molds without the tooling (pattern and core boxes) necessary when conventional technology is used (Eyad, 2016). This is particularly advantageous when dealing with intricate shapes and/or when a limited number of parts must be produced within a few days rather than in 5 weeks. An additional advantage is gained when producing prototypes (Johnson, 2016) as changes are much less costly and time consuming when made on a numerical 3D drawing rather than on patterns and core boxes. 3D printing is normally economical for a small number of parts; however, if the part is not too big and very intricate in shape such as the part that will be studied in the present work, 3D printing can be economical even for an important number of castings to be produced. On the other hand, low pressure casting is a high integrity casting process in which the mold cavity is filled from the bottom via a transfer tube in which the liquid aluminum rises under the pressure applied at the surface of the melt as illustrated in Figure 1. The filling can thus be precisely controlled, eliminating the turbulence created when the mold is filled from the top (gravity casting). Also, the pressure applied on the melt during solidification results in excellent feeding of the casting when conditions of directional solidification are met. In the present work, the compressor impeller shown in Figure 2 will be sand cast by low pressure."

Jan 1, 2018

By Rodney G. Orr, Phil Robertshaw, Roland Loewer, Klau Lehnert-Thiel

This paper documents the 1988 discovery and subsequent evaluation (to 1991) of diamond bearing kimberlites in the Fort à la Corne area, Saskatchewan, by Uranerz Exploration and Mining Limited. Cameco Corporation began participating as a joint venture partner (50%) in mid-1989. The first indications that kimberlite-type intrusions might exist in the area carne from Geological Survey of Canada aeromagnetic maps. Because of the overburden thickness (over 100 m), magnetometer surveys continue to be the main exploration tool in defining pipe locations and sizes. Magnetometer surveys in varying levels of detail have outlined one main cluster and two sub-clusters, the main group being some 10 km by 50 km in size. In excess of 70 individual targets have been interpreted from the magnetics as probably representing kimberlites. The size range of the individual magnetically-defined bodies is between 1 ha and 74 ha. Proof that the magnetic anomalies were kimberlite intrusions carne in 1989 when each of seven test holes, all drilled on different targets, intersected the potential diamond host rock. The majority of the targets tested were diamond-bearing, with the indicator mineral chemistries suggesting that both peridotitic and ecIogitic diamond parageneses could be expected. To date, 18 individual kimberlite bodies have been drill-tested. A total of 39 bulk samples, amounting to 186 t (representing 360 t of theoretical sample recoveries) were processed in 1990 and 1991. One hundred and sixty diamonds were recovered, averaging 0.04 carats in weight, the largest being 0.6 carats. Most of the bulk sample grades are less than 2 carats/loo t; only three bulk samples have higher grades, the best being approximately 10.5 carats/l00 1. The diamonds are predominantly gem-quality stones.

Jan 1, 1992

By Mayumi Ito

Mineral processing of rare-earth ore from the Dong Pao deposit, Vietnam, was investigated. The ore contained bastnaesite, (REE (rare earth element)) CO3F, as the valuable mineral and barite, quartz, and fluorite as gangue. To establish a mineral processing flowchart, selective comminution, size classification, and magnetic separation were tested. Bastnaesite shows brittle properties and selective comminution was applied to improve the purity of products. The crushed products were classified by decantation, and the overflow product showed high purity of bastnaesite indicating that bastnaesite becomes fines by crushing and that selective crushing can be used to concentrate the bastnaesite. Magnetic separation for the sink product was carried out and the mag-product showed high recovery rates of bastnaesite, indicating that the combination of size classification and magnetic separation is effective.

Aug 1, 2013

By M. Bender, H. D. Goodfellow

"Belt conveyors, because of their low capital and operating costs and inherent flexibility in handling a wide variety of products, have numerous applications in the mining industry. With the increased emphasis on improving the workplace environment, dust emissions from belt conveyors at transfer and other points have become a significant problem for many applications.The paper reviews belt conveyor dust control technology and compares dust emissions from belt conveyor systems with other possible materials handling systems. Technical information on existing belt conveyor installations which have been designed to minimize or eliminate dust emissions is summarized. The important features of good design as well as the necessary input from operating and maintenance personnel are highlighted. The status of research and development work on dust control on belt conveyor systems on a world-wide basis is discussed. A proposed methodology for field measurements of emission factors from belt conveyor systems is presented. Data collected from such a test program can be used to establish a design basis for new dust-free belt conveyors.IntroductionBelt conveyors have proven themselves over the year s in the mining industry as a reliable and low-co st method of moving bulk material at high tonnage rates. Because of the above, as well as their inherent flexibility in handling a wide variety of products, belt conveyors are often called the ""workhorses"" of bulk material handling systems. For many processing plants, belt conveyors serve as the ""vital link"" in providing feed to the plant and the removal of the finished product. As would be expected, there has been considerable engineering effort in designing rugged and reliable belt conveyor systems.It is also well known that belt conveyor systems are a primary source of respirable dust emissions. The major sources are from the tail pulley where material is received and the head pulley where material is discharged, from the return idlers, due to the fine material attached to the return belt, and from the take-up pulley. It is usually considered that for dust particles less than 10 microns, these particles will remain airborne and thus can have a profound effect on the workplace environment."

Jan 1, 1982