Search Documents

By M. F. Almeida

"Due to the randomness of all factors influencing the sintering operation, a two-stepped procedure is proposed to find the best way of using stocked fines at a plant producing Fe-Mn alloys for the steelmaking industry. The approach is based on the following: (1) predict the result of the sintering operation by establishing the best multilinear regression model using some of the characteristics of the loaded material; and (2) find the best solution under a minimizing cost criteria by solving a linear optimization problem using the regression equation plus constraints on the feed and product. IntroductionSome tests carried out using 20% to 30% of sinter in the material loaded into a 60 000 KVA Tysland-Hole electric furnace producing Fe-Mn alloys for the steelmaking industry indicated: (1) a meaningful decrease in the off-gas temperature and, consequently, a better energy use due to the material higher porosity; (2) more uniform heat distribution as a consequence of the electrode reaction zone enlargement; (3) an improved furnace control resulting in a smoother operation; and (4) a decrease in gas production facilitating the off-gas treatment. For some years, this plant used only the coarse fraction of the Mn ores, thus stocking all the received and own-generated fine particles. In view of the mentioned results, a strategy for increasing the use of stocked fines was formulated, including a step where it was necessary to decide which components and respective quantities should be used in the blends to be sintered (Almeida, 1984).It is well known that several factors affect productivity and energy consumption in sinter production, also influencing the product quality. Raw materials characteristics, namely chemical and size composition, affect permeability to gases and may or may not allow a deeper bed. In general, finer ores decrease permeability, increasing electricity consumption by fans, but due to their higher specific surface area, react more completely with other components in the mixture. For coke granulometry, a compromise must be obtained in order not to burn it too quickly nor to widen the flame front, therefore decreasing productivity. Decreasing coke in the blend also acts in sinter bonding, decreasing its consistency and increasing crushing and return fines. Moisture addition also influences components mixing, pre-agglomeration, bed permeability and, consequently, sintering productivity. Therefore, optimum conditions must be established for both a given sintering plant and the components in the feed (Dawson, 1993)."

Jan 1, 1998

By Dalton. J. L., H. P. Dibbs

An account is given of investigations into the application of two neutron methods to the on-line analysis of slurries. One deals with the application of the neutron moisture gauge principle to the determination of the water content of iron oxide slurries, and the other with the application of gamma radiation from thermal-neutron-capture to the determination of the composition of aqueous slurries of iron oxide, copper oxide, zinc oxide and sulphur. Linear relationships were found between the composition of the slurry and the neutron count-rate in the first study, and between the slurry composition and the prompt-gamma-ray count-rate in the second study. A mathematical relationship has also been developed which relates changes in the prompt-gamma-ray counts from hydrogen to changes in slurry composition.

Jan 1, 1973

By Brennan Lang

Why Seal Tunnels? ?Restore groundwater levels to pre-mining conditions. ?Saturate rock mass to reduce acid rock drainage. ?Reduce discharge flow to the environment. ?Reduce or regulate flows to a water treatment plant.

May 1, 2002

By Ken McIntyre, Trodel Wolf-Dieter

"Sirius Minerals is a UK based fertilizer development company focused on advancing into operation its polyhalite project in North Yorkshire, England. The operation is known as the Woodsmith Mine which has an estimated 2.7 Billion Tonnes of reserves and is currently in the construction phase. DMC Mining Services was selected to carry out the construction of four shafts for the project, a production shaft of 6.75m diameter to a depth of 1594 m, a ventilation shaft of 6.75 m diameter to a depth of 1565 m, and two additional shafts to support the construction of the material transport system (the MTS and Lockwood Beck intermediate) to 360m in depth for servicing the underground conveyor network for transport of product from the mine site to the costal port facilities located at Teasside. This paper will review the status of the project to date and the innovative approaches that DMC is utilizing to ensure a safe and successful shaft sinking project. INTRODUCTION The Woodsmith Mine in North Yorkshire is a Sirius Minerals-owned deep potash and polyhalite mine located near to the hamlet of Sneatonthorpe, Whitby in North Yorkshire, England, approximately 75 km east of York. The area of interest is more than 700 km2. The £3.2 billion project is to develop the Woodsmith Mine to extract polyhalite, and a tunnel system to transport it to a materials handling facility and harbour at Teesside. The site is the world's largest and highest-grade deposit of polyhalite and is expected to produce 20 million tonnes of polyhalite, potash and POLY4 per annum, as well as create over 1,000 direct jobs and many more indirectly. It has the potential to generate over £2 billion of annual exports for the UK. As the project will require mining to be undertaken in the North York Moors National Park, many objections were raised about the mine. Sirius Minerals has gone to great lengths to ensure that the project is sensitive to the local landscape, including: mineshaft head frames that will be positioned below ground to reduce their visual impact; surface buildings will be kept to a minimum; and the entire site will be landscaped and screened by existing woodland to blend in with the surrounding area. The project will also abide by strict environmental limits which govern our activity during the construction phase."

Jan 1, 2019

By Scott Rosenthal

?EMESRT History ?Design Philosophies (DP?s) ?Industry Successes ?Participation Thinking Differently Earth Moving Equipment Safety Round Table ? Use a critical mass to influence Marketing ? Define ?Problems?not ?Solutions? ? Leave the OEM designers to develop solutions Work within the companies to improve purchasing

May 1, 2010

By J. O. G. Posada

Magnesium derived foams were prepared by using the so-called baking of powder blended precursor material method. This method comprises mixing magnesium powder with a small fraction of blowing agent (ZrH2, Cs2CO3 and CaH2) and Ni like catalyst, compacting this mix and creating a foam by heat treatment above the magnesium melting temperature. The resulting samples were characterised by microscopy, gas adsorption (BET method) and by small angle neutron scattering. Several mathematical models were used in order to determine particle size distribution, fractal dimension and total pore volume fractions.

Jan 1, 2005

By H. Dundar

The first application of High Pressure Grinding Rolls was in 1985 at a cement plant, for the purpose of capacity improvement. Then various circuit configurations were derived to achieve a reduction in overall specific energy consumption, by transferring more of the grinding required to the HPGR. In most circuit configurations, the recycle of fines is required for effective breakage between the rollers. By increasing the fines amount in the feed material to a specific level within the recycling load, a uniform material bed is created and a higher pressure gradient along the roller width is obtained, resulting in compact flakes, including more fines. The fines recycle results in enhancement of the interparticle breakage. This paper will discuss the effect of the feed size distribution on HPGR performance.

Jan 1, 2012

By A. Sadough vanini A. Kami

In this paper, effects of different ageing treatments on the mechanical properties, microstructure and formability of 7075 aluminum alloy have been studied. Forming limit diagrams of the alloy have been obtained for four ageing conditions including T6, OA1, OA2 and O. For this purpose, combination of uniaxial tensile tests and the Erichsen cupping tests with different sizes and shapes of sheet specimens have been performed after each ageing treatment. The highest formability and the lowest formability have been observed at samples with O and T6 ageing treatments, respectively. Also, investigation of precipitated microstructures showed that the size of precipitation particles has a significant effect on the formability of the alloy. Formability improves with coarsening of precipitation particles.

Oct 1, 2011

This paper aims to increase our understanding about existing capacity-building approaches and their implications for obtaining a social license to operate in the mining industry. The notion of ?capacity building? is gaining increasing currency in the mining sector in developing countries due to a rapid rise in the globalisation of mining operations. Capacity-building is conceived here as a process that lasts after the mine-cycle, intended to provide local mining communities with tangible skills and knowledge to gain meaningful employment in mining or other industries relevant for the local economy. Building community capacity to understand and effectively respond to these transformations is vital for obtaining a social license to operate, as it promotes sustainable and locally relevant development. Accountability mechanisms such as global norms and international standards increasingly highlight the need to build capacity among stakeholders, particularly among local communities adjacent to mining operations. International frameworks and mining companies have embraced the notion of capacity-building as a driver to assist corporate social and operational performance. However, this narrow understanding of capacity-building through the prism of corporate social responsibility and ?best practice? is preventing the industry from meaningfully impacting communities and maintaining a social license to operate. This latter notion is being widely embedded across multiple industry sectors, as a social and economic reward from mining companies to compensate communities for natural resource extraction and gain social acceptance. Although both concepts are widely recognised in the minerals industry, insufficient attention has been paid to the implications of applying a top-down (mining-orientated) or a bottom-up (community-orientated) capacity-building approach for obtaining a social license to operate, or indeed how these two concepts are linked and applied in practice. At times, communities lack the necessary capacities in the form of education and skills to deal with mining-led livelihood transformations. This is preventing both mining companies and communities from forging sustainable livelihoods and responding to mining-led livelihood transformations, a situation that is creating discontent among communities and reducing the possibility of obtaining and renewing a social license to operate for the industry. Based on a review of current scholarly debates, accountability mechanisms in the mining industry and fieldwork findings in Colombia, this paper will contribute to an understanding of the implications of existing capacity-building approaches that support a social license to operate.

Aug 1, 2013

By A. J. Hyett

Due to the ongoing revolution in electronics and communications more cost-effective geotechnical instruments can be manufactured using digital technology. This new generation of digital instruments have embedded microcontrollers that provide highly accurate and reliable measurement of geotechnical behaviour in real world units that can be immediately interpreted. Digital measurements can be transmitted across existing mine-wide wireless communication networks, interfaced directly with infra-red enabled PDA?s or PC?s, and parsed to memory by low-cost data-loggers.

Apr 1, 2005

By Ron Ferris

The Westinghouse Temptifier TM, using heat pump principles, recovers lowgrade waste heat in the 600P to 1600P temperature range and amplifies it to usable levels of up to 2200P. Coefficients of performance (C.P.D.) normally encountered are from 3.0 to 6.0, with capacities from 200,000 to 10 million Btu/hr.

Jan 1, 1979

By Brian O'Hearn, Doug Hanson

"The most commonly used tendon supports in the Sudbury area include rock bolts, rebars, friction anchors and cable bolts. Due to the fact that these tendons are physically different and employ different anchoring systems they offer varying degrees of stiffness, yield ability, load capacity, anchor dependability and energy absorption. These differences coupled with variable rock mass and changing stress conditions have made it challenging to engineer the design of an effective support system. By tapping into the knowledge and experience gained by ground control practitioners, an empirically based rating system has been assembled that offers a guide to designers of support systems when choosing the most effective tendon support over a range of rock mass and stress conditions.A methodology referred to as support planning can be used to design support systems whose rehabilitation costs will be minimized. The use of multiple tendon types in anyone support layout is advocated, particularly when the stress state of the rock mass to be supported is expected to undergo a change."

Jan 1, 1995

By D. Nikols, G. Caraghiaur, P. C. Roxburgh

"IntroductionThe Highvale Mine is located 70 km west of Edmonton , Alberta on the south side of Lake Wabamun. It has been developed by TransAlta Utilities Corporation as a captive mine to supply fuel to two genera ting power plant s. The mine is owned by TransAlta and operated under contract by Manalta Coal. Within the mine permit area, TransAlta own s the right to mine 80% of the recoverable surface mineable coal.The planning process starts with the annually produced 25-year energy forecast which is provided by the Electric Utility Planning Council (EUPC). A 1983 forecast predicts an average annual increase in energy requirements of 4% over the next 25 years. Put another way, the requirement will double before the end of the century. A lar ge part of the base load generation of the Province of Alberta is provided by th e plants fueled from Highvale Mine. The Highvale Mine is therefore expected to maintain a high output over a long period of time.Mine PlanningMine planning is an ongoing, interative process that draws from many sources. All levels of planning draw from the same sources but du e to the different processes and objectives of each planning class, the degree of influence may differ. The planner becomes then a coordinator bringing together data and excerpts from several disciplines in groups. Generally, there are four classes of mining plan s; these are all used at the Highvale Mine (Table I)."

Jan 1, 1986

By Leon C. Botham

?? Review of Requirements ?? Components of Modeling ?? Water Management ?? Tailings Management ?? Primarily a water management problem ?? Solids relatively easily contained ?? Process flows and runoff a continuous stream over life of mine ?? Need to allow this to safely happen over wide range of conditions

May 1, 2008

By Robert B. Parsons

"It is easy to throw darts at government - and government often deserves to be a target. This month, Tax Notes examines tax legislation from a different angle, and sees some bright spots.The following article is based on a paper presented by the author at the International Gold Symposium in Rio de Janeiro in August 1989Introduction""No man's life, liberty, or property are safe while the Legislature is in session.”With one federal government, ten provincial governments, and two territorial governments all claiming to have constitutional rights to tax and otherwise regulate Canada's mining industry, and with each of these thirteen governments pursuing their respective rights with some vigor, government involvement in one way or another is an accepted way of life in the industry. While one's initial reaction to government involvement in an industry might be one of scepticism or fear, generally speaking the federal, provincial, and territorial governments in Canada tend to be pro-mining. They recognize the importance of the mining industry to Canada, especially in terms of job creation and exports. It is not surprising, then, to find that an array of valuable fiscal incentives are available to the industry through federal and provincial legislation.This paper summarizes the principal incentives that are inherent in Canada's tax legislation, as well as the Canadian Exploration Incentive Program. Although it is beyond the scope of this paper to deal with all of the incentives that are available, it is noted that various forms of federal or provincial assistance are also available outside of specific legislation, through negotiation with government departments. This latter type of assistance is generally directed toward helping with the cost of infrastructure such as roads or hydro lines, or Jess often toward loan guarantees or similar financing assistance."

Jan 1, 1990

By G. M. Ritcey

The recovery of copper from low-grade solutions res ulting from dump leaching is well known, whereas the recovery from highly concentrated copper solutions has not been practiced. This paper discusses the use of Ashland Chemical's Kelex 100, a substituted quinoline, for the recovery of copper from solutions resulting from leaching copper-nickel concentrates. A flow sheet is described, and an economic comparison shows Kelex 100 to be superior to either the LIX 64N or LIX 70 reagents of General Mills for the recovery of copper.

Jan 1, 1973

By C. A. Godden, T. N. Atkinson

Metallographic techniques developed from studies of corrosion films and electroplated coatings on aluminum alloys, are discussed. These methods, the result of work at the Naval Research Establishment, give extremely flat fields at the interface despite the large difference in hardness, in cases where electrolytic polishing could not be used. Techniques to overcome the similarity in refractive index of immersion oil, aluminum ox1d~, and mounting plastic are also considered, as are methods for improving visual and photographic contrast in areas of interest. A device for marking specimens is also de-scribed. ELE•CTROLYTIC polishing is inapplicable in the study of surface films on aluminum, whether corrosion films or electrodeposits. Mechanical procedures must there-fore be followed. Sample flatness and edge retention are of paramount importance. Special measures are required in the study of oxide films, because of the close proximity of the refractive indices of aluminum oxide, mounting plastic, and immersion oil.

Jan 1, 1962

By K. Iturralde

The topic of this article is the automation and robotization in refurbishment processes of industrial buildings. The need to mold these production spaces is quite universal. Particularly in the regions with a high industrial development and with a lack of buildable land, there is a need to convert this kind of spaces into an improved production system. The latest developments can be a useful tool for achieving a more efficient way of reforming this type of construction. On the one hand we have the digital or computerized 3D Laser Scanning (Computer Aided Measurement) that allows an accurate 3D modeling of the entire building. On the other hand, the project management using BIM (Building Information Modeling) could provide an easy design of each of the elements of the refurbishment. Finally, through the production of construction elements using robotics as jig or for CNC (Computer Numerical Control) we achieve a neat production of each element. How can be all those technologies applied in the refurbishment or expansion of industrial buildings? The research takes a first approach and analyzes industrial buildings that can be called generic or not specialized. To narrow the field of refurbishment, three major factors are defined. The first is to minimize the bill of the energy consumption of the buildings. This could be done either insulating the envelope, reducing the waste-volume to be conditioned climatically or creating facilities for energy production. The second is that the refurbishment or expansion of industrial buildings should try not to interfere on the production process that takes place in the building. In other words, the assembly of the elements in the construction site should be quick and easy, causing the least of disturbance at the workplace. Finally, the research makes an approach towards a robot integrated industrial or productive building .

Aug 1, 2013

By Iina Vaajamo, Jani Jansson, Lauri Pesonen

In pyrometallurgical operations, structural integrity of a high temperature furnace plays a crucial role in the overall safety, profitability and ecological footprint of the plant. Furnace integrity is related to how reliable a furnace is and it can be compromised, for example, by having poor operating and maintenance practices, an inefficient cooling system and flaws in the overall furnace design. These flaws and poor practices might lead to unexpected shutdowns, production losses, increased emissions, or worse. This paper presents the main factors to consider when engineering a furnace and developing its operating practices, while ensuring safe and reliable operations without compromising process efficiency and quality of the final products. In this respect, Outotec’s solutions for the cooling system and for automation systems like PROSCON, Process Advisor, Sentinel and our Smelting Information Management System, are also introduced.

Jan 1, 2015

By S. Schwartz, T. Bilney

"Over recent years a number of techniques have been developed as part of the AMIRA1 P9 project to represent mathematically or measure directly sub-processes occurring in flotation cells. These include the determination of:•,?a machine parameter (bubble surface area flux, Sb);•,?a froth parameter (froth recovery, Rf );•,?entrainment and drainage parameters (???and d); and•,?an ore floatability parameter (Pi).These flotation parameters allow the plant engineer to develop a model of the flotation circuit that can be used as a powerful tool to diagnose the performance of that circuit. The recently developed JKSimFloat V6 flotation simulator uses these parameters to predict the flotation circuit performance that would arise from changes in operating conditions and circuit configuration.This new flotation technology was applied to the Placer Kanowna Belle Gold Mine in Western Australia. A series of plant surveys, cell characterisation measurements and laboratory batch tests were conducted to determine the flotation circuit model parameters to be used within the JKSimFloat V6 simulatorA thorough flotation circuit analysis was then performed at Kanowna Belle using JKSimFloat V6. The recommendations that were provided by this circuit analysis have resulted in large improvements in the flotation performance at Kanowna Belle. These include a 1.3% increase in flotation gold recovery and a substantial decrease in operating costs. The analysis is still ongoing, however, the benefits already obtained from applying this technology have resulted in a US$1.3 million a year improvement to the mine."

Jan 1, 2005