Search Documents

By D. A. MacLeod

DURING the past fourteen months, dust surveys have been made at thirty-six mines in the Province. These surveys are made to determine the concentration of dust in the mine atmosphere, the flow of air through the mine, the methods adopted to prevent the generation of dust, and the measures taken for its elimination. When high concentrations of dust are encountered, suggestions are given for its prevention ?and elimination wherever possible. Dust sampling is absolutely necessary to determine the effectiveness of any measure taken in the prevention and elimination of dust in the mine workings. Consequently, more time has been spent on this phase of the work than on any other. The apparatus used is the Devers circular konimeter and Zeiss microscope. At various mines, the Zeiss konimeter is used, and the dust counts taken by the two instruments have given results that are closely comparable; so much so that either instrument can be used with confidence and the results obtained will compare in accuracy with those obtained by the methods used in Ontario and South Africa. Before the Workmen's Compensation Act Amendment Act was passed in November, 1936, most of the mine operators were already keenly interested in the prevention of silicosis. This interest has been intensified at all the mines, and measures have been adopted to decrease the amount of dust in the mine atmosphere. Several operators have spent a large amount of time and money in bettering these conditions, and have met with decided success. Practically all others are adopting the known methods of prevention, suppression, and elimination of dust, that apply to their ?particular mines. To prevent the production of dust in underground workings should be the first, as it is the most important, aim, especially during the time the men are underground. An atmosphere free of dust cannot be obtained, but measures can be adopted to lower the concentration that is found? in the average mine.

Jan 1, 1939

By Andreas Gaich

COMBINED 3D IMAGES _ Highly detailed 3D geometry _ Identification of fine fractures together with a general impression of the situation _ Dealing with unfavourable outcrop geometries

May 1, 2009

By M. Pötsch, A. Kluckner, P. Söllner, W. Schubert

"The in situ block size is a key parameter in the geomechanical characterization of rock masses. It describes the fracturing of the rock mass and thus is a measure for the degradation of the rock mass strength. Several classification systems use the in situ block size. For instance, the Geological Strength Index (GSI) requires the “blockiness” and joint surface condition factor as key input parameters. The “blockiness” has recently been related to the in situ block volume (Cai et al., 2004). Due to the limited information about the internals of a rock mass, it is not possible to determine the in situ block size directly. Currently, the in situ block size is determined by calculations using oversimplified models, vague estimations or, due to the lack of relevant information, it is neglected. As remote measurement systems have become available for rock mass characterization, a more comprehensive record of discontinuities can take place. Measurements can be performed on exposed rock outcrops and in particular on tunnel faces and walls, delivering the location, orientation, spacing and persistence of discontinuities at an arbitrary number and locations. An estimation of the in situ block size at the same level of sophistication is still not available. This paper aims at examining the relationship between visible and measureable information at the rock surface, and the in situ block size. Three-dimensional block model simulations were performed using the block model engine of the distinct element code 3DEC. Initial investigations focussed on the minimally required observation area in order to obtain reliable block size distributions. Based on a representative volume element, a reference distribution of the block area at the observation area for a specific discontinuity system was determined. Subsequently, the size of the observation area was decreased stepwise and each new distribution was compared to the reference distribution. For all analyzed systems, it turned out that the mean block area must be smaller than 1% of the observation area to achieve a reliable block size distribution. Further simulations focussed on discontinuity systems with three non-persistent sets. The results were compared to the formula proposed by Cai et al. (2004). A transformation factor T was introduced which replaces the persistence terms in Cai et al.’s proposed formula. The factor describes the correlation between block volumes generated by persistent and corresponding non-persistent discontinuity sets. The simulations included the variation of the discontinuity set spacing, persistence, and orientation. The mean and additionally the 25%-, 50%- and 75%-quantiles of the block size distribution were analyzed. Examining all values for the transformation factor the distribution can be described by a power function with a negative exponent. The function depends on the persistence only. Finally, the results of random simulations were compared to the analytical formula using the transformation factor. The predicted mean and selected quantiles show a good agreement with the simulation results. It gives a comprehensive picture about the block size distribution in discontinuity systems with three non-persistent sets."

Jan 1, 2015

By J. Jung, W. Keller, A. Zucht

"The agitator design for nickel high pressure acid leach autoclaves (HPAL) is critical with regard to the process result, i.e., the recovery rate. Further considerations during the design phase are the avoidance of acid hot spots which reduce the lifetime, due to corrosion of the wetted parts, including components manufactured from titanium. Besides the process knowledge to design HPAL autoclaves, tools such as, Computational Fluid Dynamics (CFD) supplemented by lab testing allow the design of optimized agitation systems. This paper describes the effect that different feed point locations have on instantaneous blending of the reactants. Furthermore, experiments and CFD show where abrasion issues might occur and how to obtain information about the static and dynamic forces acting on internals. We show how simulations can be validated by lab testing to ensure that the CFD models are applied in an appropriate way.INTRODUCTIONAgitated systems in hydrometallurgical processes have to comply with multiple process tasks and in many cases have to withstand extreme operation conditions such as pressure up to 50 bar, elevated temperatures of up to 250°C and exposure to very acidic or alkaline environments and abrasive ores. The process tasks range from instantaneous mixing of reactants, homogeneous suspensions of up to 65% wt. solids with coarse and heavy particles, enhancing the solid-liquid mass transfer for leaching, dispersing large volumes of reactants (gas-liquid, liquid-liquid mass transfer) and moreover to transport generated heat e.g., from exothermic reactions through the vessel walls or internal heat exchangers if required. For economies of scale, agitator systems have reached sizes of 5000 m³ for large open leach tanks with impeller diameters of approx. 6 m, while autoclaves nowadays have exceeded 5.5 meters in diameter with a power demand for a single compartment drive between 300 - 400 kW. In parallel all process industries require a more efficient use of resources, to generate less by-products and higher yields, while ore-bodies tend to be less qualitative and new process routes (e.g. direct leach) are developed. Besides all these facts the mixing solution must be robust and economic. In this paper we want to address our approach in the development and designing of HPAL agitation equipment."

Jan 1, 2012

By L. Vinnett, I. Panire, J. Yianatos, F. Ruiz

"The effect of operating variables on the flotation performance at steady-state has been extensively used for modelling and simulation of separation processes. However, the dynamic characterization of key variables such as gas dispersion (Sauter mean diameter of bubbles, D32, and bubble surface area flux, SB) and froth discharge rate is rather scarce. In this paper, an experimental design allowed identifying the dynamic response of the flotation process in a laboratory scale flotation cell, using a two-phase system, airwater. The installation included automatic control for the superficial gas rate, JG, and the pulp level. Gas dispersion was evaluated in terms of the Sauter mean diameter of a bubble population and the bubble surface area flux, SB = 6·JG/D32. The D32 was measured using the McGill Bubble Size Analyzer (MBSA) along with a semiautomated algorithm. In addition, the froth discharge velocity was measured in real-time using a Visiofroth system. The control variables were the superficial gas rate and the frother concentration (Teefroth). The dynamic characterization of the flotation process is useful to design algorithms that allow the direct or indirect control of metallurgical variables such as flotation rate, concentrate grade and mineral recovery.INTRODUCTIONGas dispersion indicates the way the gas entering a flotation machine is dispersed throughout the volume of the equipment (Schwarz & Alexander, 2006). The gas dispersion is typically characterized in terms of the bubble size (dB), gas holdup (eG), superficial gas rate (JG), and bubble surface area flux (SB =6·JG/dB) (Finch et al., 2000). All these variables have significant impact on the metallurgical performance of flotation machines. For example, Perez-Garibay et al. (2014) investigated the effect of the particle size, bubble size distribution, superficial gas rate and collector dosage on the flotation performance, for the separation of a sphalerite mineral. The authors observed that recovery increased with the superficial gas rate ranging from JG = 0.04 to JG = 0.08 cm/s and also a maximum recovery was obtained for bubble size close to 300 µm. Gorain et al. (1998) reported a strong correlation between the flotation rate constant and the bubble surface area flux in a zinc cleaner circuit. Both variables were directly proportional at three froth depths in the range of hF =7 - 45 cm. Dobby & Finch (1986) incorporated the effect of the superficial gas rate and the bubble size on the flotation efficiency by means of a kinetic model for the rate constants. Yianatos & Contreras (2010) developed a model to estimate the carrying capacity in large flotation cells by including the bubble surface area flux."

Jan 1, 2016

By Micheal Mayhew

"This presentation will provide information and facts on the drilling and blasting within a frozen shaft using a full face methodology. The Author will briefly discuss the history of the sinking of a frozen shaft in Saskatchewan, the challenges faced, and the solutions delivered. The case study will include a discussion describing the series of events that led to the decision to adopt a full face blasting methodology. The case study will describe key elements such as the drilling pattern, hole size and depth, explosive products and blast vibration monitoring systems. INTRODUCTION During the shaft sinking process at a project in Saskatchewan, it was recommended that a drill & blast benching method be utilized. Following an evaluation of the site, the geological conditions proved amenable to a ground freezing system that would stabilize the rock formations and prevent inflows of water into the shaft (Table 1).The shaft sinking process required that the ground surrounding the proposed shaft be frozen by drilling several near vertical freeze holes radially at a specified distance from the edge of the proposed shaft excavation. This would allow for the circulation of a chilled brine solution down the freeze holes. The circulation is achieved by means of stainless steel pipes encased within each other to provide a delivery and return conduit for the brine (Figure 1). As a result of this periphery freezing, the ground within the shaft excavation is also predominately frozen.The finished internal diameter of the shaft was 5.5 meters with varying overall excavation diameters to facilitate different liner designs used for various rock formations. For the most part, the fully unsupported/unfinished excavated diameter of the shaft varied from 6.9 meters to 8.5 meters depending on the zone excavated. The challenge was that the proposed drill and blast excavation method posed a significant risk due to the potential to damage the freeze wall and pipes during blasting. The decision was made to commence the excavation through mechanical excavation (i.e. chip and cut) methods then change to a drill and blast method utilizing a split benching design. Through this process, the team encountered five main challenges: 1. Sub-horizontal geological structures and slips that affected blasting performance and sometimes resulted in a sloping surface to the top of the bench; 2. Confined working area for the crews and equipment due to a limited work area as a result of utilizing the split (half) bench drill and blast methodology; 3. Mechanical chipping and cutting of the one-meter buffer zone to the final shaft diameter; 4. Crews working on extremely slippery uneven frozen rock and ice surfaces, which affected safety and efficiency; 5. Establishing a blast vibration monitoring system to determine if the drilling and blasting of the full shaft excavation diameter were acceptable."

Jan 1, 2019

By S. Kelebek, U. Demir, T. C. H. Richards, E. Koss

"Laboratory-scale tests were carried out to investigate the response of a high-grade (~143 g/tonne) well-liberated gold ore to flotation using two collector types. Octyl and amyl xanthates, representing conventional types of collectors, were tested against an n-octanoic and hexanoic acids under moderate and high redox potential conditions. The latter was based upon a suggestion in literature that monocarboxylic acids are able to adsorb onto the surface of gold at redox potentials near 600 mV (SCE). This investigation did not demonstrate that these carboxylic acids could function as collectors for gold in real ores. In fact, they appear to have slightly depressed gold. However, the results demonstrated that octyl and amyl xanthates acted as highly effective gold collectors for this ore and that an increase in the collector dosage led to an increase in recovery for all mean particle sizes. In some tests, gold recoveries of around 95% were attainable in concentrates with grades around 6 kg/tonne, indicating that xanthate flotation remains a viable means of concentrating gold even at coarse grain sizes. Various aspects of the process such as grade-recovery performance and recovery by size are discussed.INTRODUCTION Three methods are used for the recovery of gold in mineral processing, either alone or in combination: gravity concentration, cyanidation and flotation. Gold occurs as a by-product in some ores together with platinum group metals and as the primary metal in other ores in the form of native gold and electrum, which are alloys of gold, silver and minor amounts of copper. Flotation is a viable method for recovering liberated gold where the gold is visible under an optical microscope (greater than 1 µm in size) and where the attachment of gold grains is not prevented due to bubble loading by competing minerals. It is generally known that grains finer than 150 µm in size will float with most collectors."

Jan 1, 2017

By R. A. Sullivan

I T IS one of the unwritten policies at Preston Mines that we examine closely any method or tool that will help us in our constant battle against rising costs. It is our personal conviction that most work methods can be improved. Therefore even though the job went well yesterday, it does not necessarily follow that it should be done by the same method today. With the arrival of the natural gas pipe line in the Porcupine area it was obvious that we would have to take a good look at the possibilities of using this source of fuel for plant heating. • Steam presently generated at Preston is for heating purposes only, no process steam being required. Prior to the fall of 1960, the heating plant consisted of two low pressure, coal-fired, fire-tube boilers, operating at an approximate pressure of 14 pounds per square inch. These boilers were underfed by stokers and could be operated either singly or together. ~o. 1 unit was a horizontal return tubular boiler, registered at 100 h.p. No. 2 unit was a fire-box boiler, registered at 75 h.p.

Jan 1, 1962

By Š. Šachlová, T. Lokajícek, M. Petružálek, T. Svitek, A. Štastná

During the past 20 years, alkali silicate reaction (ASR) as a cause of concrete deterioration has been studied by a wide range of experimental methods such as microstructural and macrostructural analysis, bulk chemical analysis, X-ray and neutron diffraction analysis, etc. All of these data are compared with expansion values of mortar bars (following ASTM standard C 1260). Recent studies indicate the useful application of non-destructive methods with the aim of better reflecting mechanical properties and the degree of deterioration of real concrete. Ultrasonic testing methods (including ultrasonic pulse velocity UPV) are widely used to determine material mechanical properties and the changes induced by a variety of mechanical or chemical processes. However, only a few laboratory studies of ASR focused on ultrasonic testing of mortar bars. Due to this fact, a heating chamber was designed and constructed to enable ultrasonic sounding of mortar bar specimens while stored in accelerating solution. Regular ultrasonic sounding of mortar bars reveals significant dependence of ultrasonic data such as longitudinal P-wave velocity, signal energy, signal amplitude and signal frequency on mortar bar storage time. Ultrasonic data were subjected to time domain as well as frequency domain analysis. Different storage conditions were used to determine the effect of ASR on ultrasonic parameters. Mortar bars, prepared in the same manner with one type of aggregate, were stored in cold or warm water or in an accelerating warm medium. Ultrasonic data accurately reflects the differences in hardening and deterioration of tested mortar bars due to different storage conditions. Ultrasonic results showed very good correlation with the results of ASTM standard expansion tests and much higher sensitivity to ASR-induced concrete deterioration. Expansion tests showed 1% measured length differences in comparison with up to 80% resolution of ultrasonic data. The ultrasonic testing proved to be a suitable laboratory method for investigating ASR-related processes and could lead to an improvement of standard testing procedures.

Jan 1, 2015

By W. V. McKnight

The paper discusses the equipment and methods used to establish some of the characteristics of a braking system. Some typical tests are described and an explanation of the approach used to derive information from the recorder charts is given.

Jan 1, 1966

By David R. Macedon

"Through the years, a wide variety of dust control methods have been utilized at mineral processing operations. While some have been successful, many have been highly ineffective. Dust Control systems currently in use include baghouse systems, fog systems, surfactant spray systems, and foam dust suppression. While baghouse systems can be effective, they are capitalintensive and costly to operate and maintain. Chemical dust control programs can be very effective. However, if applied incorrectly, they can have detrimental effect on mineral recovery. Thus, many operations utilize a combination of baghouses and water, often with limited success.Recent advancements in surfactant and polymer chemistry have resulted in substantially improved chemical dust suppression programs. These products range from non-corrosive surfactant/humectant combinations for road dust control to foam-based systems for crushers and transfer points, to advanced polymers for pile binding and soil stabilization. These advances are discussed in detail, citing results from fieldwork in the precious and base metals industries.INTRODUCTIONThe global nature of the mineral processing industry presents a unique set of challenges. Traditional thinking would tell us what works in one place should work in another. This could not be further from the truth in the area of dust control. We learn very quickly that there are a number of factors that can affect the efficiency and success of a dust control program and that these factors are not all chemical or equipment related. Some of these factors include facility maintenance, product selection, water quality and characteristics, and economic considerations.What has been learned from past experience is that each mineral processing plant presents a unique set of factors that will affect the ability to create an optimal dust control program. This paper presents a myriad of treatment options that will highlight the advancements in chemical dust suppression products and equipment."

Jan 1, 2004

In order to avoid impurity problem and enhance absorption/desorption kinetics of Mg-based compounds, nanostructured Mg-based compounds were synthesized from Mg, Ni and other elemental nanoparticles produced by hydrogen plasma-metal reaction. XRD and TEM results demonstrate that homogeneous nanostructured Mg-based compounds with less impurity were successfully synthesized by this method. DSC in hydrogen atmosphere, pressure-composition isotherm and the kinetics of hydrogen adsorption/desorption were investigated at different temperatures. The results show that the nanostructured Mg-based compounds can absorb hydrogen in a high speed at a low temperature.

Jan 1, 2005

By D Reddy Chinnasane

Outline Location of BirchtreeMine and Layout of 124 OB Cut and Fill Mining Background Purpose of the Studies Methodology Results and Analysis Conclusions and Recommendations

Oct 1, 2010

By A. E. Wraith, J. Protheroe Jones, P. J. Mackey

The world’s first copper electrorefinery started production in 1869 at Burry Port in South Wales. Built within the Pembrey Copper Works which had commenced smelting operations in 1849, the new refinery was based on principles described in the British patents issued to J.B. Elkington in 1865 and 1869. Refining principles and practices pioneered there were key to the foundation of modern electro-refining practice in what is now a dominant international industry producing over 16 Mt of electrical grade copper annually. This paper explores the background to this pioneering application of the new, early 19th century, science of “electro-metallurgy” and examines its links to the contemporary decorative electro-plating industry and to the shortcomings of 19th century fire refining. The beginnings and early years of the Pembrey electrorefinery are briefly discussed in relation to the quality, applications and pyrometallurgy of copper at the time. More than a decade would elapse before the birth of the electrical age: the Pembrey refinery may be seen as one of its vital precursors. Note: This paper was originally published as part of the Copper 2013 proceedings (A.E. Wraith, P.J. Mackey and J. (formerly R.) Protheroe Jones, “Origins of Electrorefining: Birth of the Technology and the World’s First Commercial Electro-Refinery”, paper in Electrorefining, Vol. V, Book 2, (Eds. R. Abel and C. Delgado), Cu 2013 International Conference, pp. 19-33, IIMCh, Santiago, Chile, 2013). It is reproduced here together with a new Appendix and supporting references that lists the year of commencement of the first electrolytic copper refinery by country, 1869 to 1956. It all, the year of the first electrolytic copper refinery established for 15 countries is included. These 15 countries now produce more that 70% of world refined copper (for 2018). INTRODUCTION In the 1840s, the new science of ‘electro-metallurgy’, a term coined by Smee in 1841 (Smee, 1841), was being adapted to the decorative electro-deposition of silver in a thin, bright adherent coating that was evidently equal in appearance to traditional silverware (Williams, 1976). Chief among innovative manufacturers of decorative objects who took up the new art of silver electro-plating was the acclaimed firm of G.R. Elkington and Co. of Birmingham, England. The company, which vigorously developed all aspects of electro-metallurgy for the decorative trade, entered the field of ‘electrotyping’, a technique in which the surface features of a mould are copied on an electro-deposited copper layer which, when stripped off, can be used to reproduce an imprint of the mould. In essence, it is a form of casting by electrodeposition, invented in 1837 independently by Jacobi in Russia (Pavlova, 1968) and Spencer in England (Wyatt, 1851).

Jan 1, 2019

By M. S. Moats

As smelter feeds become more complex, the impurities that ultimately report to electrorefineries are changing. Many of these impurities collect in the electrolyte and must be controlled. As commercial copper electrorefineries look to expand their capacities by increasing their operating current density, the interaction between electrolyte composition and anode passivation can cause operational difficulties. To improve the industry's understanding of the passivation phenomena, the role of electrolyte composition was evaluated using commercial electrorefining anode samples. The electrolyte composition variables examined were copper, acid, nickel, arsenic, chloride, thiourea and glue. Finally, the role of non-commercially utilized additives, such as bromide and polyethylene glycol were studied. From this investigation, electrolyte parameters that inhibit copper dissolution through copper sulfate precipitation, copper oxide stabilization and/or absorbed species lead to accelerated passivation. Species that prevent passivation have the ability to complex cuprous ions. Possible mechanisms for the role of each.

Jan 1, 2007

By T. Cutard, E. Cailleux, F. Nazaret, G. Bernhart

This paper deals with the study of the mechanical behavior in the 20°C-900°C temperature range of refractory concretes reinforced with metallic fibers. Fibers are introduced to improve the damage resistance and to minimize the quasi-brittle behavior of refractory concretes. In some cases, a plastic or ductile like behavior can be obtained. Two approaches are considered in these studies. The first one is based on the micromechanical scale. Main objectives are to understand, quantify and predict the thermomechanical behavior of monofiber microcomposites. Such considerations are helpful to optimize the composite formulation for a better behavior. The second one is based on the macromechanical scale. Main objectives are to characterize and to model the macroscopic thermomechanical behavior of randomly reinforced refractory concretes. A particular attention is firstly paid to the relationships between the microstructural changes and the mechanical properties and secondly to the structural size effects.

Jan 1, 2004

By F. Rojas, M. Sanchez, J. Palacios, O. Pavez

Copper sulfide is the main mining resources in Chile, and most of this metal is obtained via pyrometallurgical extraction in seven copper smelter plants, which extends from the northern Atacama desert to the central part of the country. In 2002, 1,522,000 metric tons of fine copper were produced, with a notorious environmental impact due to the large amount of slag generated, including transportation and disposing problems. Therefore, there is a great interest in finding alternative uses in order to give additional value to the slag. This is a total project development concept, which consider residues as new resources where new components could be obtained, improving sustainability in mining activities and also ensuring clean production processes. Thus, the present work shows a review of copper slag characterization as well as several ways of utilization, including compact material for road and railway installation, part of admixtures in concrete.

Jan 1, 2004

By Ron Doucet

Industry today is now more than ever dependent on its assets and on the standard of maintenance. Changes in technology, environmental regulations, a continually improving focus on safety and global competitiveness has made maintenance a key activity in sustaining safe, financially viable and environmentally integral operations. Maintenance used to be looked upon as a cost centre with a sole focus of fixing equipment to attain high availability. Maintenance today affects all aspects of the business: safety, environmental integrity, energy efficiency, productivity, costs, and product quality. These new demands on the function of maintenance requires us to think vastly differently about what maintenance is all about, even to the point of contradicting old beliefs. In the following paragraphs we will examine some of the changed thinking that has evolved over the last 50 years. These new concepts will lay the foundation for the implementation of 21st century best practice maintenance.

May 1, 2003

By Steve McMullan, Blaine Webster, Ian Johnson, Ron Matthews

"Time domain spectral Induced Polarization (IP) data from the Tower, Jojay and Laurel Lake gold deposits in northern Saskatchewan are presented. The resistivity data shows both resistivity lows (due to fault, shear or alteration zones) and resistivity highs (due to silicification) in the area of the deposits. The high resistivity zones suppress and distort coincident IP responses, calling f or high quality surveys and special care in interpreting the IP data.Electromagnetic methods are not effective in locating the deposits. This is due, in part, to masking by conductive cover. The Jojay Lake deposit has a strong magnetic response. A more indirect magnetic association is seen for the Tower Lake deposit. The Laurel Lake deposit has no magnetic signature. Magnetic data are useful in defining structure in all cases.All three deposits are outlined in the IP survey results. IP anomaly amplitudes from the pole-dipole array are from two times (Tower and Laurel Lak e) to six times (Jojay Lake) background values. Gradient array IP anomalies are of less amplitude. The spectral time constant is short for the Tower and Laurel Lak e deposits and long for the Jojay deposit. This implies that the metallic sulphides in the Jojay deposit are more interconnected than those of the other two deposits. INTRODUCTIONInduced polarization / resistivity surveys are commonly used in gold exploration program s in the Canadian shield because the IP method is effective in detecting disseminated metallic sulphides which are often found associated with gold. Other common geophysical sur vey methods such as magnetics, VLF and EM are not generally capable of direct detection of disseminated sulphides. Since the introduction of the IP method in the 1950s, it has undergone continuous improvement. The most recent improvement is the development of time domain receiver s which sample the full de cay and record it in digit al form. This results in a more complete measurement of the response which permits analysis and enhancement of data quality and the derivation of a nomaly parameters which characterize the measured decay. This extension of conventional time domain IP methods is called spectra l IP, a term first introduced by Pelton et al. working in the frequency domain Spectral IP surveys are attractive because they allow the possibility of discriminating between IP responses which have similar amplitudes but are due to dissimilar geo logic targets. The discrimination can be important in the selection of IP anomalies for follow-up.Time domain spectral IP survey results are presented over three known gold deposits in northern Saskatchewan-Tower Lake, Jojay Lake and Laurel Lake. The surveys were initiated and supported by Cameco-A Canadian Mining and Energy Corporation (formerly the Saskatchewan Mining and Development Corporation-SMDC) and were carried out by JVX Limited using the Scintrex IPR-II receiver and attendant spectral analysis software."

Jan 1, 1989

By Stephen Williams

This paper examines manning best practice in the Australian mining industry. In particular, the paper considers a range of mining operations and their manning levels as measured by operational benchmarking. The benchmarking results presented cover 15 open pit and 37 underground studies in Australia. The data was collected as part of AMC?s benchmarking and operational improvement studies conducted between 1999 and 2008. The results examine overall manning levels in mining, processing and administration functions. Manning levels for a range of mining methods, including open pit and underground methods, are segmented. Productivity measures such as ore tonnes per man day and metres developed per man day are presented and where direct relationships can be established, the relationships are described. Finally, the paper considers perspectives on best practice with regard to manning in the Australian mining industry and the limitations in application of this type of analysis in a global context.

May 1, 2009