Search Documents

By James Ball

The paper describes a new type of pump and related apparatus specifically designed to dredge sea-floor minerals from very great depths. The principle of operation of the dredging system is explained, and the factors which determine the equipment size and the power required for varying mining rates and depths of water are discussed. An estimate of the capital and operating cost of a commercial-scale mining system is presented.

Jan 1, 1968

By M. J. Dry, G. B. Harris

"This paper presents basic chemistry and operating conditions for the hydrolysis of ferric chloride into solid hematite and gaseous hydrogen chloride, and shows how this unit operation can be applied in chloride hydrometallurgy to regenerate strong hydrochloric acid and reject iron without also rejecting valuable metals such as nickel, copper and cobalt. Two examples are used to illustrate the hydrolysis technology and compare it to existing technology. The first is the regeneration of spent steel pickling acid, comparing hydrolysis to conventional pyrohydrolysis. The second example is the processing of a hypothetical low grade nickel laterite, comparing the novel chloride hydrolysis route to conventional sulphate HPAL technology.INTRODUCTION Whilst, in many respects, the control and removal of dissolved iron from chloride leach solutions can resemble the manner in which it is done in sulphate systems, chloride chemistry additionally offers the ability to achieve the same objectives in different ways (Harris, 2014). Conventionally, iron is oxidised to its ferric state (if necessary) and then precipitated with a base, usually magnesia where the feed is a laterite and lime where it is a sulphide, since calcium will precipitate sulphate formed during leaching. One method for controlling iron is to form FeOOH, either ß-FeOOH (akaganéite), a-FeOOH (goethite), or a mixture thereof (Fillipou and Choi, 2002). However, if akaganéite is formed, the precipitate will contain a significant chloride component (as high as 7% Cl), leading to chloride losses and difficulty in satisfactorily disposing of the residue. Washing chloride from akaganéite is almost impossible due to the propensity of the solids to undergo peptization. The conventional approach requires the addition of a base, but it is based to some extent on controlled supersaturation precipitation (Demopoulos, 2009), which produces a more uniform and crystalline material and is far more attractive than, for example, the turboaeration process proposed by Great Central Mines in their chloride copper process (Raudsepp & Beattie, 1986)."

Jan 1, 2016

By Nick D. Rose

The Dy deposit is a 21 Mt Pb-Zn-Ag-Au SEDEX-type massive sulphide resource located in the Anvil District, Faro, Yukon. This relatively unexplored orebody lies at a depth of 480 to 920m below surface, dips 20 to 35o and comprises vertical ore thicknesses of 3 to 28m at a 9% Pb + Zn cut-off grade. The deposit has been tested at depth with 63 surface diamond drillholes, but has not yet been explored or developed by underground means. Over the past decade, pre-feasibility investigations were conducted for two separate owners of the property to determine the economic viability of developing an underground mine at Dy. Following these previous studies an assessment was undertaken between 1998 and 2000 to further investigate geotechnical considerations for underground mining. The results and conclusions drawn from this study provide direction for possible future exploration at Dy.

May 1, 2002

By E. C. Morton

The Western Australian School of Mines (WASM) has developed a facility for the static testing of large scale ground support elements. The samples are loaded using a mechanical screw feed jack. Instruments measure the displacement and the load being applied. Methods have been developed for testing of mesh, shotcrete and membranes. Mesh samples are restrained on all sides and loaded centrally. A new large scale punch test method has been developed to evaluate shotcrete and membranes. These products are sprayed on to a sandstone substrate containing a centrally located isolated disc. The sprayed product is loaded by displacing the disk. The different test methods are described in detail. The test program involved two types of mesh, several shotcrete mix designs with different curing times and one membrane product. The force-displacement responses are used to directly compare the products. The implications for implementation of the different ground support products are discussed.

May 1, 2009

By E. M. De Souza, P. Lausch, D. O. DeGagné, J. F. Archibald

"The potential use of industrial and municipal waste glass as a partial pozzolanic replacement for Normal Portland cement in mine backfill has been investigated. Considerable quantities of glass are currently discarded into landfill sites at high cost to municipal and industrial users with no foreseeable environmental benefits being gained by such disposal. This research study was undertaken to assess the viability of using ground waste glass materials as partial binder replacement of Portland cement fractionswithin consolidated mine backfill materials. The program was implemented to review various factors that could influence successful incorporation of glass waste replacement of cement, these factors being the feasibility of glass waste procurement, determination of process economics and the physical and chemical suitability of ground waste glass materials to generate adequate backfill strength when replacing Normal Portland cement fractions. A series of laboratory assessment trials were established to evaluate backfill component characteristics and mixture strength properties for both standard Portland cement-consolidated and blended Portland cement/ground waste glass-consolidated backfill materials. Side-by-side review of the strength behaviour of various component backfill/cement mixtures was designed to permit comparative evaluation of the capabilities of ground waste glass and Portland cement products as backfill consolidating agents"

Jan 1, 1995

By J. Shen

Direct methanol fuel cells have been the subject of considerable research in the last decade. Performance levels realized in cells, stacks, and systems show that this technology is a promising power source for a wide range of portable applications. A direct methanol fuel cell (DMFC) operates directly on a methanol fuel stream typically supplied as a methanol/water vapour or as an aqueous methanol solution in liquid feed DMFCs. The fuel streams in DMFCs are usually recirculated in order to remove carbon dioxide and to re-use the diluent and any unreacted fuel in the depleted fuel stream exiting the DMFC. The concentration of methanol in the fuel circulation loop is an important operating parameter because it determines the electrical performance and efficiency of the direct methanol fuel cell system. The methanol concentration in the circulating fuel stream is usually measured continuously with a suitable sensor, and fresh methanol is admitted in accordance with the signal from the sensor. There are many factors to consider in developing a methanol sensor suitable for DMFCs. These factors include sensitivity, cost, size, simplicity, reliability, longevity, concentration range, and dynamic response. In particular, reliability and low cost should be addressed. Methanol concentration sensors measure methanol concentration by means of detecting the variations of physical/chemical properties of the solution. In this work, methanol concentration sensors based on electrochemistry, electric-capacitance measurement, infrared sensing, ultrasound sensing, and other techniques are reviewed to discuss their advantages and disadvantages.

Jan 1, 2005

By A. C. Hatton

Doped SrCoO3.8 was found to be a promising material for use as a cathode component in intermediate temperature SOFCs. In this work, strontium cobaltite ceramics doped with 10 mol% to 90 mol% samarium were synthesized using the glycine nitrate process in order to study the electrical conductivity and thermal expansion at temperatures of up to 800°C. As-synthesized powders were deagglomerated, pressed and sintered at temperatures ranging from 1100-1250°C. The effect of temperature and composition on electrical conductivity and thermal expansion are presented and discussed.

Jan 1, 2005

By Masayuki Ishikawa

In a radio frequency and optoelectoronic device packaging, Gold-Tin (Au-20 wt% Sn eutectic) solder is used widely due to the excellent electrical and thermal conductivity, high strength, and negligible creep characteristic under repetitive thermal cycling. With the recent lead-free movement, Gold-Tin solder is recognized as an alternative material for high temperature Lead-Tin solder. Generally, Gold-Tin solder is supplied in the forms such as ribbons, pellets, and ring frames. However, these forms must be set-up accurately on the joint area to press chips in bonding, therefore, it is difficult for these forms to satisfy the recent requirements for the down sizing in the connection areas. On the other hand, Au-20 wt% Sn solder paste can be applied flexibly to various supplying methods, such as printing, dispensing system and pin transcript. These methods also make it possible to reduce the production cost. However, in the case of using the solder paste, the void issue is one of the most undesirable problems. The void causes the degradation of the characteristics such as the bond strength, electrical characteristic and thermal conductivity. We have been intensifying the development of the void free paste, and have achieved void reduction by optimizing the powder size, the flux composition and the reflow condition.

Oct 1, 2003

By Qian Liu

Mining in highly stressed ground conditions has been an increasing challenge at the Brunswick Mine. Two large regional pillars were established on the 1000 m Level to support the ground for safe extraction of the surrounding ore. The South Regional Pillar contains about 5 million tonnes of ore and the North Regional Pillar has about 3 million tonnes of ore. In the fall of 2000, mining activities were suspended following a series of ground movements around the South Regional Pillar along weak geological structures. After extensive geotechnical investigations, a decision was made to carry out a mass destress blast in the West Ore Zone (WOZ) to cut the principal stress across an area of 135 m along strike and 86 m high. At the end of July 2001, the WOZ mass blast was successfully initiated. Following this success the mine decided to take a similar approach to destressing the North Regional Pillar (NRP). The final mass blast was taken in early February 2003. Advanced blasting technologies, including state of the art electronic detonators and blast simulation, played an important role in achieving the successful blasts. The high precision of delay timing and long delay duration of the electronic detonators ensured accurate and reliable initiations of over 800 blastholes in the WOZ mass blast. Orica?s DMC_Blast (Distinct Motion Code) simulation code was used to study different blasting blocks for the desired timing in the initiation sequence. This paper describes the process of applying electronic detonators in complex blasts, and discusses how blast simulation results were interpreted to guide engineering design of the mass blasts.

May 1, 2003

By J. Duriez, L. Scholtès, F. V. Donzé

"Fracture propagation process in brittle rock is investigated by means of numerical simulations performed with an adapted formulation of the discrete element method. The progressive failure mechanism is simulated through the breaking of the bonds making up the cohesion between the elements constituting the simulated medium. The use of appropriate contact laws associated to a near neighbor interaction feature provide the model the ability to reproduce fundamental characteristics of brittle rock behavior such as, for example, high values of the tensile to compressive strength ratio. Great attention is given to accurately describe the properties of the pre-existing joints or faults in the model. A specific joint model gives the possibility to define a tailor-made behavior of the discontinuity surfaces without suffering from discretization bias.Compression test simulations are performed on pre-flawed samples and compared to experimental results in order to validate the numerical approach for describing the initiation and propagation of fractures in brittle rock under mode I+II loading. It is shown that the crack mechanical parameters can greatly influence the fracturing pattern, in particular its frictional properties. Overall, the numerical simulations reproduce fairly well the failure patterns that are obtained experimentally.The discrete model is then used to study mode I+III loading to give an insight into fracturing problems occurring at the scale of the continental crust. The ability of the model to support mechanically the physical modelings performed with wet clay or sandbox is shown. As an example, the model is used to track the development of a twist crack system (wrench fault) through the nucleation and coalescence of microcracks."

Jan 1, 2015

By L. E. Reed, I. G. L. Sinclair

An exploration program seeking kimberlite pipes, the common primary hosts for diamonds, Was' conducted during the years 1979 through 1982 in the James Bay Lowlands of Ontario by Selco Mining Corporation (now the Mining Division of BP Resources Canada) and Esso Minerals Canada. The area to be explored was selected on the basis of its regional geological setting, and because of the known presence of kimberlite indicator minerals in the region. The primary exploration technique was low level airborne magnetic surveying, followed by detailed ground geophysics. This work located many pipe-like bodies, with diameters of a few hundred metres, as well as several dykes. Targets located by these geophysical methods were drilled, intersecting a total of45 intrusions, consisting of34 alkaline diatremes containing tuffisitic breccias, 7 carbonatites, and 4 massive alnoites. K-Ar determinations indicated ages of 152 Ma and 180 Ma for two of the massive alnoites. The texture and general mineralogy of the tuffisitic breccias are similar to those of diatreme facies kimberlites, but detailed examination of their mineralogy and chemistry demonstrated that they lie within the alnoitic rather than the kimberlitic compositional field. Although the exploration program did not lead to the discovery of true kimberlites, it did demonstrate the presence of a large, previously unknown province of alkaline volcanic activity, which has no surface expression.

Jan 1, 1991

By A. Chieregato, C. G. Oñate Salazar, D. Martinelli, D. Peila, M. Barbero

This paper is aimed to confirm the possibility to excavate fractured rock masses by using EPB shields, even in presence of relevant water tables. This verification is based on laboratory test experiences carried out at TUSC laboratory of Politecnico di Torino, where the natural material is tested in order to verify the suitability of a certain conditioning technique in particular conditions. This is due to the fact that every case should be studied apart from existing studies on a certain rock type, as other factors such as fragmentation of the rock mass, natural water content and porosity of the rock can considerably influence the final result of the conditioning process. The most important aspects that allow to consider the conditioning of fractured rock masses as suitable are: possibility to create a plastic paste that can transmit the pressure at the front in a effective way; reduce the permeability of the spoil material in order to reduce the possibility of water leakage inside the chamber and eventually in the tunnel; verify the consistency of the conditioned material for the extraction through the screw conveyors and the belt conveyors. For this research an argillitic schistose rock mass, with some quartzitic and calcareous inclusions, has been studied by using different level of conditioning in order to verify the suitability of an eventual EPB excavation through this formation.

Jan 1, 2015

By D. Ouellet, G. Gagnon, B. Simser, V. Falmagne

The mining sequence at Noranda’s Bell- Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modelling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the redimensioning of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

Jan 1, 2004

By G. M. Ritcey, A. W. Ashbrook

"This paper summarizes the optimum leach conditions for each Of several cobalt-containing arsenical feed materials, describes the solution treatment prior to purification of cobalt recovery, and discusses the plant operation on one feed as well as the treatment of effluents.IntroductionDuring the period 1962-1964, when the demand for uranium was low, Eldorado Mining and Refining Limited (Eldorado Nuclear Limited) made a decision to undertake a three-year diversification program. One area chosen in this program was that concerned with the processing of cobalt-nickel materials. Many such materials were evaluated over the three-year period, ranging from tailings, residues, ores, concentrates and speiss to metal scrap. Cobalt feed materials, on which much of the effort was concentrated, were those containing arsenic together with other metals such as silver, copper, nickel and iron. This paper describes the treatment of arsenic-bearing feed materials (ranging from 0.3 to 570/0 As) and the subsequent purification stages required before the separation and recovery of high-purity cobalt. Because of the current interest in treating cobalt ores, it seemed appropriate that the information on the treatment of various cobalt feeds should now be made available . Although a large amount of data were generated during the research and process development program, a complete scientific correlation and understanding could not be achieved. Nevertheless, the data may provide a guide to others involved in processing not only cobalt, but other arsenical ores."

Jan 1, 1981

By BARRY BANNATYNE

Ombrotrophic Sphagnum peat bogs have a characteristic signature on both colour injrared film (750 nm to 3,000 nm response) and Daedalus injrared line-scanner images (thermal infrared 3 to 5 microns and 8 to 14 microns response). This remote sensing method was used to survey bogs in southeast Manitoba to delineate targets for surface exploration. Target bogs all have a surface growth of Sphagnum; underlying dead Sphagnum ranges from 1 to 6 m thick. Large Sphagnum reserves exist in the Caribou cluster of bogs, and in /979 a bog first identified by infrared sensing was brought into production.

Jan 1, 1984

By J. A. Hurd

Towards the goal of a better understanding of the structure-proton conductivity relationship in PEM materials, this project concerns the design of ordered polymeric solids containing well-defined sulfonate aggregates. The approach employed involves the templation of sulfonated monomers using core principles of crystal engineering. In addition to sulfonate groups, the monomeric units contain crosslinkable functionalities to enable formation of a covalently linked network. The templation strongly directs the construction of well-defined sulfonate clusters and aggregates. Structural, sorption and conductivity data for the networks will be shown.

Jan 1, 2005

By Henry Stoch

It?s a green, green world ? Public concern about the impact of human activities on the environment and the roles that businesses play in that impact is rising. What?s happened in the last few months? ? Recent news: ? British Columbia announces carbon tax in 2008 budget ? Federal Court ruling stalls oil sands approvals due to a lack of consideration of GHG implications ? US Energy Independence and Security Act could limit government procurement of oil sands-derived fuels ? Western Climate Initiative (WCI) suggests a ?first seller? approach for regulating generators outside WCI jurisdictions ? Implications ? A cost for carbon has arrived ? The lack of a GHG strategy can have a material impact on your business ? Regulations in other jurisdictions could affect your organization

May 1, 2008

By P. C. Garg

"IntroductionThe Central Mine Planning and Design Institute (CMPDI) of India, started planning the extraction of thick seams highly susceptible to heating in 1977by the French method of sub-level caving and/or multi-slicing. Nitrogen flushing was proposed for inhibition of heating by the author in one such project - the Kotadih colliery.Inhibition of heating was unheard of in the Indian coal industry before 1977-78. The usual practice was to seal off a district or a part of the mine or the entire mine when spontaneous heating occurred. With very little equipment in a normal bord and pillar district and a low production rate, the financial loss in capital assets and in production did not warrant any serious thought for inhibition of spontaneous combustion. With the planned advent of longwall mining, particularly sub-level caving, with heavy capital investment as well as high production potential, the sealing of a longwall face due to spontaneous heating could not be considered an appropriate solution.Principle of Inhibition of SpontaneousCombustionFrench engineers have established that a fire will not break out when oxygen is 15% or lower in the general body of the air. However, once a fire starts, the percentage of oxygen has to be reduced to 2% - 4% to extinguish it. It is this principle which has been used at Blanzy Coalfield in France to inhibit heating and it is claimed that this has retrieved the integral sub level method of mining. Nitrogen infusion has been used in Frence since 1978 to keep the oxygen content below 14% in the goaf."

Jan 1, 1987

By Boris Yacksic, R. W. Bruce

"The flotation of a cassiterite ore with oleic acid will recover primary or rougher concentrates assaying over 10 per cent Sn, with a recovery of 80 to 90 per cent. These rougher concentrates cannot be up-graded to a marketable grade by normal reflotation. Experiments were conducted on low-grade tin ores, and a process was developed for up-grading the rougher flotation concentrates by a reverse flotation technique. The process was tested on a number of samples of ore from the Catavi mine in Bolivia. The results of these tests showed that a concentrate assaying 40 to 60 per cent Sn could be readily produced, with a recovery of 60 to 75 per cent of the tin in the ore."

Jan 1, 1967

By B. Rivard, D. Francis

A layered Archean magma chamber is exposed at the base of the Yasinski segment of the La Grande greenstone belt. This intrusive complex lies beneath a sequence of mafic volcanics and is underlain by granitoid basement which is crosscut by a swarm of gabbroic dykes. The gabbros of both this complex and the dyke swarm of gabbroic dykes. The gabbros of both this complex and the dyke swarm define a pronounced Fe-enrichment trend. The volcanic patterns of the La Grande and Eas tmain greens tone belts, however, define a series of iron depletion trends which originate in the iron enrichment trend of the gabbroic intrusives. These patterns suggest that the gabbros produced in the intrusive complex may serve as parental liquids for some of the lava suites of the James Bay greens tone belts.

Jan 1, 1984