Search Documents

By L. Beiza, L. Velásquez-Yévenes

Chalcopyrite is by far the most abundant copper sulphide on Earth, but it has proved to be problematic in its processing by leaching, mainly related to its refractory nature, slow kinetic rates of dissolution and the formation of an inhibiting product layer on its surface during leaching. This study is focussed on the electrochemistry of chalcopyrite dissolution in acidic chloride system, which has recently gained attention as a feasible alternative to conventional sulphate media for chalcopyrite leaching. It is well understood that chalcopyrite dissolution from mineral grains depends strongly on the solution redox potential at the mineral surface as well as the composition of the product layer that may form on its surface. The chloride ions in solution support the Cu(II)/Cu(I) couple as the primary oxidant, as they can form complexes with the cuprous ions formed, increasing the dissolution rate. Additionally, these ions increase the potential range where chalcopyrite can be oxidized. The chemical reaction that occurs on the surface of chalcopyrite in chloride solutions in the presence of cupric ions will be characterized and the coulometry of the reaction will be reported to understand what is happening on the surface of chalcopyrite. Electrochemical experiments have been carried out to investigate the behaviour of mixed potential by open circuit potential (OCP) measurement for 30 minutes using sulphuric acid at pH 1 under nitrogen at 25⁰ C. The effect of chloride was analysed at 0, 20, 50 and 100 g/L and cupric ions from 0 to 50 g/L. The potentials obtained were then used to carry out chronoamperometry tests for a period of 30 minutes in absence of cupric ions. The mixed potential did not show a significant difference with an increase in cupric concentrations in the absence of chloride. Increased mixed potentials and current densities were observed at higher chloride and cupric concentrations. Chronoamperometry tests at those potentials were used to construct a voltammogram trace which has the same trend as a normal cyclic voltammogram but with much lower current densities. INTRODUCTION As a result of the depletion of copper oxides, the leaching of copper sulphide minerals has become the focus of many studies. Chalcopyrite, (CuFeS2) which is the most abundant of copper minerals, has proved to be challenging to process via hydrometallurgy, mainly related to its refractory nature, slow kinetic rates of dissolution and the formation of an inhibiting product layer on its surface, during leaching.

Jan 1, 2019

By J. P. Rajot, H. Mouzannar, M. Bost

"The design of rock foundations may need to evaluate shear strength of rock-concrete interface by performing laboratory direct shear tests. A series of tests were carried out on specimens for different values of the spacing free of encapsulating material about the shear plane and different values of normal stress. Different kinds of failure were observed and not necessarily at the rock-concrete interface. The spacing free of encapsulating material appeared to be of significant influence on the test results. A mechanical analysis is presented which illustrate the influence of the loading conditions in the direct shear box on the failure mechanism. INTRODUCTIONThe design of rock foundations subjected to significant lateral loads requires defining the value of the shear strength of the interface between rock and cast in place concrete. Verifying the stability against sliding of strip footings subjected to inclined loads (SETRA, 2009) or concrete gravity dams (CFBR, 2013) are common examples where design modelling approaches imply the shear strength, sometimes the deformation behavior, of the rock-concrete interface, more or less assumed as a failure plane.Defining the behavior of rock-concrete interfaces relates to tribology. Many studies have been conducted to improve the representation of this behavior (e.g., Johnston & Lam, 1989; Kodikara & Johnston, 1994; Gu, Seidel & Haberfield, 2003; Saiang, Malmgren & Nordlund , 2005; Fishman, 2008; Eltervaag, 2013; Gutierrez, 2013), raising many questions. The behavior appeared to be influenced by many factors such as the geometry of the interface which is not planar, the roughness of the natural rock, the rock mineralogy and the concrete formulation. In addition, the study of the shear strength of rock-concrete interfaces involves considering the two different deformation behaviors of both rock and concrete. Finally, the observed failure mechanism is strongly influenced by the initial cohesion due to adhesion between the two materials when concrete is directly cast onto rock."

Jan 1, 2015

By Don Peel, Jeremy Richards

Abstract - Aggregates (sand, gravel, and crushed stone) are low unit-cost products extracted in very large volumes for the construction of buildings, roads, and other infrastructure essential to modern society. Because of their low unit value, transportation costs are a key factor in resource economics, and deposits are commonly developed close to market (i.e., close to towns and cities, or along low-cost transportation corridors). This proximity results in potential conflict with residents over land use, disturbance, and pollution. Management of aggregate resources in Alberta is examined in the light of resource geology and distribution, and governance. A case history of development of the Calahoo-Villeneuve deposit is described, and the conflicts between residents and developers that led to establishment of an Area Structure Plan (ASP) are explored. The plan sets limits to, but at the same time safeguards, resource extraction, and defines terms for compensation to residents through a voluntary levy on production (Community Enhancement Fund). This fund is used to support community activities and to pay for a groundwater monitoring program. The ASP is examined within the context of the "Seven Questions to Sustainability" as set out by Mining,Minerals and Sustainable Development-North America (2002). It is concluded that the ASP, for the most part, provides a good model for conflict resolution and sustainable resource development, which could usefully be applied in other jurisdictions. The ASP was developed at a municipal level, and adoption at a provincial level would aid sustainable development of aggregate resources across the province.

Jan 1, 2003

By Claude Dufresne

The technical development of the niobium-bearing products is to a great extent influenced by the striving of the respective industries to maintain or strengthen their positions in all fields of application against competing materials. South East Asia, China, Eastern Europe and CIS are slowly becoming significant consumers of ferroniobium. As a result, the world niobium market has been stable despite the slowdown in steel production in 2001. This paper will describe present producers, capacities and the current market conditions.

May 1, 2003

By G. D. West, J. D. Purdue

"Marked Ball Wear Testing (MBWT) employs identified grinding balls which are placed in an operating mill for a period of time, retrieved from the mill, and then measured to determine the amount of wear experienced. This is an excellent method to evaluate the relative differences in the wear rates of various grinding ball materials and/ or manufacturing process variables simultaneously and under actual production milling conditions. This paper outlines the methods of ball identification, testing and evaluation procedures and discusses the strengths, weaknesses, and proper application of marked Ball Wear Test results. INTRODUCTIONThe consumption of grinding media in the mineral processing industry represents a substantial cost to the comminution process. Grinding media is most often found to be the second highest consumable cost next to energy. To determine the selection of the most cost effective media, one must determine the specific wear mechanisms present in a given grinding application and decide which media system addresses these mechanisms most economically.A MBWT has definite advantages over other methods used to evaluate the relative consumption rates of grinding media. It allows the comparative testing of a large number of different ball types under identical operating conditions in a very short period of time. In addition, production wear rates can be accurately predicted directly from MBWT results. Typical MBWT test periods are in the order of 350 to 700 operating hours for high wear rate application and upwards of 2000 or 3000 hours for low wear rate applications. These times are much less than the 5000 or more hours required to purge a mill of the incumbent ball charge (to convert it to the test ball) and then provide even a minimal test period in which to conduct a full production test, for just one type of ball. Under production test conditions the evaluation of competitive product or the development of improved grinding balls is necessarily slow."

Jan 1, 1991

By K. Spence

"The notion of “value” has always been a subjective and contentious issue. Indeed, value is in the eye of the beholder. There are as varied methods and practices for valuing property, as there are industries in which they are applied. For example, there is replacement value, insurance value, salvage value, appraised value, book value, and fair market value, to name a few, although in the mining industry, valuations usually refer to fair market value.In the Canadian mining industry, at present, there are no comprehensive regulations or guidelines that specify which approaches or methods are appropriate for use in the valuation of mineral projects. In January 1999, The Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission recommended that the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) establish a committee to review and advise on approaches and methodologies for the valuation of mineral properties. Among the approaches to be considered are included the following: the discounted cash flow approach, the cost approach, the option pricing approach and the market comparables approach. In addition, methodologies differ depending on whether the project is at the exploration stage or the producing stage.The CIM Special Committee on the Valuation of Mineral Properties (CIMVal) expects that its final report will form the basis for a Canadian code or standard for the valuation of mineral properties."

Jan 1, 2002

By Ann Lamontagne

Le parc à résidus de l?ancienne mine Dunraine contient des résidus générateurs de drainage minier acide. Le concept proposé pour la restauration du site est d?utiliser le fort potentiel alcalin des boues rouges, résidus d?aluminerie, afin de neutraliser les résidus miniers. En appliquant une certaine quantité de boues rouges à la surface du parc, on provoquera une neutralisation de l?acidité. De plus, les alcalis contenus dans les boues rouges vont provoquer la précipitation de minéraux stables (sulfates tel la jarosite). La précipitation de ces minéraux provoquera la formation d?une couche indurée qui rendra difficile la circulation de l?oxygène et de l?eau. Bien que ce concept ait été vérifié en laboratoire, ce sont là des hypothèses qui restent à vérifier dans des conditions réelles d?exposition. Les principales questions soulevées par l?utilisation des boues rouges, mis à part le contexte géochimique, est le contexte technico-économique. En effet, le transport de quantité importante d?un matériel argileux humide présente un défi économique important. Outre le défi économique, la manipulation et l?épandage de ce produit sur des parcs à résidus constituent également un défi important. Cet article présente les conclusions d?une étude technique sur le transport, la manutention et l?épandage de boues rouges sur un parc à résidus situés en Abitibi : le site de Dunraine.

Nov 1, 2002

By P. Kolodziejczyk

Mining seismicity can be harmful both under and on the surface. ? Tremors are not totally damaging, but destructive to buildings and infrastructure, especially in highly urbanized regions, such as Upper Silesia in Poland ? Destroy the social appreciation, trust and support for mining industry ? To prevent or reduce these effects, engineers and scientists develop methods allowing prediction of ground shaking intensity near buildings and various losses that can result from it Evaluation and prediction of mining tremor?s damaging influence on buildings is usually solved with two steps: ? Estimation of local ground shaking intensity (based on known attenuation relation) and classification into one of several predefined intensity intervals ? Apply supposed relation between the shaking intensity interval and qualitatively defined damaging effects to express predicted effects This makes a mixed quantitative/qualitative procedure, difficult to analyze or optimize

Aug 1, 2013

By Z. Zhang

Aluminum boron carbide particulate reinforced composites have found new applications in nuclear industry due to their special capability to capture neutrons, Recently, Alcan successfully developed a liquid metal mixing process to fabricate Al¬B4C metal matrix composite instead of powder metallurgical technology. In the process, titanium is added into the composites to control interactions between boron carbide particulates and aluminum matrix, To understand the effects of titanium on the composites, the solidification microstructure of Al-16%B4C without or with titanium was examined by optical and electron microscopes. The results show that titanium can improve the uniformity of the particulate distribution within aluminum matrix if the titanium content in the composites is more than 0,5%, Furthermore, it is found that the layer with rich titanium on the surface of the particulates can limit the formation of AlB2 type compounds, which may greatly deteriorate the fluidity of the composites, In addition, it is also found that the amount of the reaction products in the composites increases with the increase of holding time. However, the rate of the increase is mitigated by the increase of the content of titanium in the composites. Besides, a procedure was proposed and implemented for the evaluation of uniformity of particulate distribution within aluminum matrix.

Jan 1, 2005

By Walter F. Atkins

Fair market value, in the legal sense , is the price which a prudent and knowledgeable buyer and a prudent and knowledgeable seller, acting without constraint or compulsion , will agree upon to exchange an asset. In the ordinary commercial or engineering usage, the term may imply simply the market value or a reasonable and equitable price. The engineer evaluator who is called upon to express an opinion about the fair market value of an asset may be able to base his estimate on the sale price of similar assets or on the market values of stock. Frequently such indicators of value are not available and the evaluator must devise other means of appraisal. Mineral resource properties may be thought of as having value by virtue of the existing or potential ability to produce at a profit. Conventional procedures permit the computation of the present value of future revenues having due regard for the time value of money and the risks attendant upon the realization of the venture. Such computations have gained wide acceptance as a basis for the estimation of fair market value.

Jan 1, 1977

By Patrick Wong, Gareth Hatch, M. A. Halim, V. I. Lakshmanan, Darcy Tait

"This paper describes development of an integrated chloride process for separation and purification of REEs. The process includes atmospheric leaching of ore/concentrate with mixed chloride lixiviant containing HCl and MgCl2 followed by bulk recovery of REEs, dissolution of the bulk intermediate product, and separation of individual REEs by solvent extraction (SX) process steps. Mixed chloride leaching technology provides the opportunity to regenerate the lixiviant, while the addition of MgCl2 in HCl enhances the hydrogen ion activity by orders of magnitude increasing REE extraction efficiency at a lower concentration of HCl. An individual REE separation process developed by Innovation Metals Corp. is being piloted at a state-of-the-art facility at Process Research ORTECH Inc. in Mississauga, Ontario, Canada. The SX process includes the separation of light REEs (La – Nd), medium REEs (Sm – Gd) and heavy REEs (Tb – Lu plus Y) from leach liquor followed by individual REE separation. Each SX circuit proceeds by multistage extraction followed by scrubbing and stripping. The process is chloride based and reagents are recycled, reducing waste generation and optimizing water usage to reduce environmental impact.INTRODUCTIONRare earth elements (La to Lu plus Y) exhibit a range of unique magnetic, electronic, catalytic and optical properties. Due to these special properties, the application of REEs is increasing and they are found in components for wind power generation, hybrid electric cars, catalytic converters, and many electronic devices.Rare earth elements (REEs) are commonly divided in two groups: light rare earth elements (LREEs) and heavy rare earth elements (HREEs). Light rare earth elements include elements from lanthanum (La) to neodymium (Nd). Although promethium (Pm) is considered an LREE it is unstable and scarcely occurs in nature and is generally excluded. Heavy rare earth elements include elements from samarium (Sm) to lutetium (Lu) plus yttrium. Although rare earth elements are not rare and the rare earth oxides are scattered around the globe, over 95% of REEs+Y are currently produced in China (Pitts, 2011). On one hand the Chinese government is restricting the export of rare earth elements and on the other hand the demand for REEs+Y is increasing in the rest of the world. This has created an imbalance in the supply and demand of rare earth elements and has led to a rush for developing new rare earth projects."

Jan 1, 2016

By John D. Carriere, Jean Leung, Daniel. Laguitton, Michael .. J. Burrows

"The objective of this expert system application in a copper-zinc concentrator, is to increase the availability of assay data through substitution for erroneous data. The assay data is used by the Operations personnel and automatic process control strategies to control flotation circuit performance. Two online X-ray fluorescence analysis systems analyze 24 streams across four divisions to provide the required data. Data availability of individual streams average 90% while the resulting circuit availabilities are 70%. The unavailability of correct data results from mechanical, X-ray or process problems. The erroneous data can be identified by process experts using knowledge relating stream interdependencies and historical process behaviour. An expert system was devised to provide real time identification of erroneous data and substitute for that data with the ultimate aim of improving metallurgical response by both the operator and automatic control systems.The paper discusses the early development work and architecture of the knowledge base designed using Neuron Data's expert shell NEXPERT.INTRODUCTIONThis paper describes the early development of an expert system (ES) prototype at the Kidd Creek concentrator. The project is a joint undertaking of the Kidd Creek Division of Falconbridge Limited and CANMET. Kidd Creek entered into the project to apply heuristic rules to the XRF assay data to improve the metallurgical control of the flotation process by increasing availability of analysis data. This project provided a problem of suitable size and future expandability while making use of a wide base of in-house expertise and experience. Another important benefit is the introduction of expert system technology to the site providing tools and experience for future system selection and technology application. CANMET has an on-going interest in assessing various aspects of ES technology (hardware, software, knowledge engineering, integration) while addressing problems in process operations that could most readily benefit from the technique. CANMET's role in the project was to provide project assistance, financial support, substitution algorithm assistance and software for data substitution. The knowledge bases (rules) have now been completed and are to be tested in the online environment."

Jan 1, 1989

By Jack Zhang, Yunguo Tang, Baodong Zhao

"Rare earth elements (REEs) have numerous key applications in both traditional and advanced technologies. A shortage of some critical REEs is expected due to the discrepancy between the REE abundance in REE deposits and the REE demand from the market. For example, Neodymium, Europium, Terbium, Dysprosium, Erbium and Yttrium are expected to be in short supply. REE recovery and separation from secondary resources such as uranium wastes, heavy mineral sands, and recycled materials can balance the shortfall in a cost effective way.The Saskatchewan Research Council (SRC) is engaged in the development and commercialization of complete REE recovery and separation technologies in Canada. One of SRC’s newest developments is the design and commissioning of a heavy rare earth (HREE) separation pilot plant. The pilot plant uses hundreds of stages of solvent extraction (SX) to produce high purity individual HREEs from both primary and secondary resources.This paper presents the design of an HREE recovery process for the particular case of uranium processing wastes. The separation results of a group separation are reported and discussed, as well as the issues and the challenges of the development, commissioning and operation of the continuous SX pilot plant.IntroductionSignificant amounts of strategic specialty heavy rare earth elements (HREEs) are found in uranium wastes in Saskatchewan. It estimated that about 47 tonne/a of heavy rare earth element oxides (HREO) including 27 tonne/a of Y2O3, plus 6 tonne/a of Sc2O3 are in the raffinate of every uranium mill for potential recovery. Since the HREEs are already in the raffinate, cost effective HREE production is promising in Saskatchewan.Selective precipitation including nutraulization, oxalate and double-salts precipitation, as well as sulfide precipitation, ion exchange (IX) and SX are commonly used technologies for the recovery and purification of REE solution. REE oxalate precipitation is an effective technology to remove Fe, Al, Ca, Si and other impurities by taking the advantages of the solubility difference between oxalates of REEs and impurities in acidic solution (Xu, 2005)."

Jan 1, 2017

By V. Prostakova, M. Shevchenko

The copper smelting gas / slag / matte / metal / solids system with the Cu-Fe-Ca-Si-O-S major elements has been a long-term focus of the present overall research program using integrated experimental and modelling approach for the phase equilibria characterisation and development of a thermodynamic database. A systematic investigation of phase equilibria of slag systems in equilibrium with Cu metal is providing information for systems where copper coexists in slag with lead, zinc, and aluminium oxides as major components. Experimental studies involve high-temperature equilibration of synthetic samples; rapid quenching; and measurement of the compositions of equilibrium phases using electron probe X-ray microanalysis (EPMA). Particularly important feature of the present study a wide range of temperatures (660-1670°C) being characterised that reveals major inconsistencies in the existing thermodynamic description of the multicomponent system, and allows to establish the thermodynamic properties from phase equilibria in a reliable way. FactSage-based thermodynamic modelling is integrated with experimental research. Initial thermodynamic assessments are used to identify priorities for experiments, planned to provide specific data for thermodynamic optimisation. Significant improvement in the accuracy of the phase equilibria description is achieved, in particular in the PbO-Cu2O-SiO2, ZnO-Cu2O-SiO2, and Cu2O-CaO- Al2O3 systems in equilibrium with metallic Cu. INTRODUCTION Slags high in lead and copper are generated in primary metal production in the smelting of lead sulfide concentrates and in pyrometallurgical metal recycling systems. The compositions of these slags are varied due to increased fraction of recycled materials in the feed as well as introduction of previously unused chemical elements to modern technology. Therefore, their processing becomes chemically more complex; in that way they contain a large number of different metals. These slags form complex non-ideal solutions (with possible formation of several immiscible slags) that can coexist with stoichiometric solids, solid solutions, mattes and molten metal depending on the bulk composition and process conditions. Predicting the outcomes of smelting and refining processes is becoming increasingly difficult. To assist in the optimisation of these metallurgical processing operations, a comprehensive research program is underway to develop accurate thermodynamic databases for these non-ferrous process systems.

Jan 1, 2019

By A. G. Pentland

PROSPECTING is popularly supposed to be surrounded with an air of romance and adventure. The word 'prospecting' brings to mind high mountains, northern lakes, and aeroplanes. A note of urgency has been added to this by the war, particularly in the case of strategic, minerals. Prospecting for strategic minerals in a modern mine in full production, although it may Jack the romance of travel in little-known places, has the advantage of having all the necessary machinery at hand and ready to go into action at a moment's notice. HISTORY Tin was discovered in the Sullivan ore in 1925, when a white streak was noticed on a pilot table which was being used to check the amount of galena in the tailing. The mineral which made up this streak was identified as cassiterite. The amount of tin in the ore is so small that, while of scientific interest, it was considered to be of very little economic importance. Nevertheless, several attempts were made to learn something of the occurrence during times when other work was nor pressing. These studies were dropped when anything came up that seemed more important.

Jan 1, 1943

By E. Asselin, P. Sauve, H. Salomon-de-Friedberg

"Residues from the CESL Copper process were leached using the CESL Gold process. The kinetics of reaction were confirmed to be fast with over 50% of the gold consistently extracted within 2 minutes of leaching. Final gold extractions under the conditions tested here were between 80-90% obtained within 90 minutes. A model for the CESL Gold process was developed. This model is slightly different based on whether the copper concentrate leach residue was ground or unground prior to leaching: the gold leaching rate constant is approximately twice as fast for the ground samples. Unground residues had a P80 of 13 ?m whereas ground residues had a P80 of 10 ?m. The model predicts a 43% decrease in leaching time for ground residue versus unground residue to achieve the same extraction under otherwise identical conditions. The model was more accurate for the ground samples. INTRODUCTIONTeck's CESL Process (Jones, 1996) was developed to provide an economically attractive alternative to traditional copper smelting. It has since evolved to also deal with copper concentrates containing valuable impurities such as nickel and undesirable ones, such as arsenic, while reducing downstream costs. Effective recovery of gold and silver is essential to the economics of the CESL Process. The Brook Hunt 2007 copper concentrate assay data (Wood-Mackenzie, 2007) were examined to determine the ratio of gold plus silver value relative to the contained copper. As indicated in Figure 1 below, nearly two-thirds of concentrates have 10% or more of their total value tied up in their precious metals content.CESL has extensively examined the recovery of gold and silver at bench, pilot and demonstration scale, which has culminated in the present CESL Gold Process (Barr et al., 2007). The process targets the precious metal contained in the leach residues produced in the copper portion of the flowsheet. This residue has two primary components which influence downstream processing. The major iron-rich fraction (-75 wt%) of the residue is a mixture of various forms of iron oxide precipitates including hematite and jarosite (Sahu and Asselin, 2011). The iron fraction ranges from amorphous to crystalline in nature depending on the compound precipitated, upstream operating conditions and feed material composition. The lesser, but by no means less important, fraction is a mixture of elemental sulphur and unreacted sulphides (principally pyrite).Elemental sulphur formed during the oxidative leach of the copper concentrate reacts with cyanide to form thiocyanate (SCN-) making a traditional cyanide leach approach too costly. Since the SCN formation reaction strongly depends on contact time with the CESL residues (Po, 2007) short contact times were preferred. This factor guided the development work towards the eventual room temperature, pressure cyanidation process which results in near complete gold dissolution in 90 minutes. A recent CESL gold demonstration campaign treating 1.5 t/d of residue from the copper oxidation step achieved an average gold extraction of 91% (96% maximum)."

Jan 1, 2012

By Lei Pan, Roe-Hoan Yoon

"Sea water flotation is becoming a reality due to shortages of fresh water. To better understand the mechanisms involved in sea water flotation, we have studied the effects of KCl and MgCl2 on the surface forces present in the wetting films of water formed on hydrophobic surfaces. The measurements have been conducted using the force apparatus for deformable surface (FADS), which is capable of measuring both the surface and hydrodynamic forces responsible for bubble-particle interactions. The results obtained with the gold surfaces hydrophobized with butanethiol (C4SH) show that the wetting films of Ultrapure water do not rupture despite the relatively high water contact angle (??= 80o) and the presence of a long-range hydrophobic force with a decay length (D) of 25 nm in the film. The film is metastable with its equilibrium thickness (he) at 140 nm, where the repulsive double-layer force is equal in magnitude to the capillary force as shown in Figure 1. The film loses its metastability and ruptures in a 10-2 M KCl solution, in which the double-layer force decreases substantially due to the decrease in Debye length (?-1) while the decay length of the hydrophobic force remains as large as 23 nm.The effects of MgCl2 has also been studied using a C4SH-coated gold surface with a water contact angle of 87o. It has been found that in a 10-4 M solution double-layer force decreases due to the decrease in the negative ?-potentials and Debye length, which should help destabilize the wetting film. However, the film remains stable due to the decrease in the decay length of the long-range hydrophobic force from 45 nm in Ultrapure water to 14 nm in the MgCl2 solution. Thus, the results obtained in the present investigation support the view that the difficulties in sea water flotation may be due to the presence of MgCl2 rather than the presence of NaCl in sea water (Ramos, et al., 2013)."

Jan 1, 2016

By J. E. Armstrong

"Pinchi Lake and Bralorne Takla mercury mines; Canada's only producing mercury mines during the past war (1939-1945); occur within the Pinchi Lake mercury belt. This belt is in central British Columbia; and is approximately 150 miles long extending from southeast of Fort St. James northwest to the headwaters of Omineca river.During the field season of 1937 cinnabar was discovered by J. G. Gray of the Geological Survey in Permian limestone on the north shore of Pinchi lake, where the main showings of the Pinchi Lake mercury mine were later developed. Following the publication of Gray's report claims were staked in the spring of 1938, and later that year were optioned to the Consolidated Mining and Smelting Company, and in June 1940 a reduction plant with a rated capacity of SO tons a day was brought into operation. In 1943 the plant had a capacity of more than 1,000 tons a day. The grade of ore treated was reported to average S to 10 pounds of mercury a ton, and production during the years 1940 to 1944 exceeded 4,000,000 pounds. The Bralorne Takla mercury mine, which is 90 miles northwest of the Pinchi Lake mercury mine, was brought into production in November 1943 with completion of a 50-ton mill. During the next 10 months more than 100,000 pounds of mercury were recovered, and the grade of the ore was reported to average 15 to 20 pounds of mercury a ton. During the war, production from these two properties was far in excess of Canadian requirements, and Canada was able to supply the United Kingdom and United States with part of their need.s. Both properties ceased operations during 1944, and, due to an excessive supply of mercury, have not yet reopened. The Pinchi Lake mercury belt lies along a northwest-trending major fault zone called the Pinchi fault zone (Fig. 1). This zone is approximately 150 miles long and varies in width from 200 to 1,000 feet . It forms the northeastern edge of a northwest trending fault belt up to 10 miles or more wide in places. In general the northeastern margin of the Pinchi fault zone represents the contact between closely folded, stratified Permian rock:s on the southwest and Mesozoic formations and Omineca intrusions on the northeast. It seems probable that the fault zone marks the site of major thrust faulting from the southwest and that the Permian rocks moved up with respect to the Mesozoic formations. Intense faulting occurs in the Permian rocks within the fault zone. There the more important faults trend north and northwest, dip steeply west and southwest, and may join a major low-angle thrust fault at depth."

Jan 1, 1954

By B. N. Church, R. H. Seraphim, J. T. Shearer

"The Lexington-Lone Star CU-Au deposits straddle the Canada U. S.A. border, south of Greenwood, British Columbia. This 3 km long linear porphyry system occurs in a northeast dipping belt of sheared quartz porphyry and serpentinite. The best grades of mineralization occur in three principal bodies known as the Pit zone, the Northwest zone and the Lexington Main zone. The Pit zone at the Lone Star mine is the largest of the mineralized bodies and consists of fracture fillings and disseminations of pyrite, chalcopyrite and minor molybdenite, hosted by the Lexington quartz porphyry. The Northwest zone, discovered by drilling through overburden near the 49th Parallel, consists of pyrite-chalcopyrite-gold mineralization in the quartz porphyry and the footwall serpentinite. The Lexington Main zone has the highest grade of gold and occurs near the footwall of the quartz porphyry with the mineralogy and setting similar to the Northwest zone. Alteration of the host quartz porphyry is mostly sericitic and chloritic; alteration in the adjacent serpentinite is mostly talc and carbonates.A weighted average of the drill-indicated reserves is 19.5 million tonnes grading 0.56% CU and 0.55 gl t Au.IntroductionThis paper describes copper-gold mineralization associated with the Lexington quartz porphyry in the Greenwood mining camp of south-central British Columbia and adjacent parts of Washington State (Fig. 1).Access to the property is mainly by a network of farm, logging and old mining roads to the U.S. border, 10 km south of Greenwood, British Columbia."

Jan 1, 1995

By Neil Westoll

But First, An Overview of the Selwyn Basin and Its Resources ?World-renowned sedimentary-exhalative (SEDEX) deposits of zinc, lead, silver +/-barite ?Significant reserves/resources remain and vast tracts of prospective stratigraphyremain under-explored and untested. ?More details are at the Yukon Geological Survey?s Selwyn Basin Metallogenysite:http://www.geology.gov.yk.ca/metallogeny/selwyn/ Overview of Metal Price and Demand Trends ?The pace of economic change in China has been extremely rapid since the start of economic reforms just over 25 years ago. According to official statistics, economic growth has averaged 9.5% over the past two decades and seems likely to continue at that pace for some time. National income has been doubling every eight years. Such an increase in output represents one of the most sustained and rapid economic transformations seen in the world economy in the past 50 years.? Organization for Economic Co-operation and Development 16-Dec-2005

May 1, 2006