Search Documents

By A. J. Smethurst, S. B. Hearn, S. Boskovic

"The problem of crud in solvent extraction is well known and can be a major handicap and operational issue. Colloidal silica can cause a number of problems including interfering with flocculation, initiating crud formation in solvent extraction (SX), decreasing SX extraction kinetics and increasing SX phase disengagement times. Flocculation can be utilized to remove some of the troublesome particulates but colloidal silica does not flocculate well and presents a different problem requiring innovative chemistry to solve. Coagulants can assist by facilitating the removal of this colloidal silica by promoting the agglomeration of the particles to a size which can be more readily settled or flocculated in solid/liquid separations. This is achieved when the coagulants bind to the surfaces, displacing water and destabilizing the colloids, whereupon they bind to each other which facilitate their amenability to conventional flocculation.INTRODUCTIONSilicate minerals are abundant in the upper layers of the Earth’s crust, and there are few mineral deposits without significant levels of gangue silicates. Silicate minerals include the pure silicas, such as quartz and other silicate containing minerals such as clays, chlorites, feldspars, as well a vast number of less common silicates.During the acid leaching of ores, two types of fine silica particles are released in solution from the dissolution of the host mineral. The first consists of partly depleted silicates, and the second is colloidal silica, which forms in solution. It is this second type which has the potential to cause crud formation as well as poor solution clarities, slow filter rates and excessive flocculant usage (Figure1)."

Jan 1, 2016

By P. W. Percival, J. J. Janssens

"Whitehorse Copper is a 2600-ton-per-day underground copper mine located within the city limits of Whitehorse, Yukon . In early 1978, due to increasingly difficult ground conditions. it was decided to investigate the conversion from longhole open stoping to vertical crater retreat mining. On-site crater testing by C-I-L demonstrated the feasibility of V.C.R. mining at Whitehorse Copper.After some investigation. a down-the-hole drilling rig was chosen and drilling began in November /978. Blasting began in June /979. and to September 1980 approximately one million tons of ore had been blasted. In-field changes to both drilling and blasting techniques have been implemented. Some of these changes were dictated by problems encountered; others were made to improve efficiencies.To date. V.C.R. mining has proven successful from a drilling and blasting aspect.IntroductionWhitehorse Copper Mines Ltd ., a division of Hudson Bay Mining and Smelting Co., Limited , is a 2600-Lp.d. underground copper mine. The plant site is located I mile west of the Alaska Highway, and approximately 7 miles south of Whitehorse city center. Production is from the Little Chief orebody, and total output is from vertical crater retreat stopes.The Little Chief and Middle Chief orebodies at Whitehorse Copper had original reserves in excess of 6 million tons, most of which graded 2.00/0 copper or higher . The orebodies are typical skarn deposits that have developed along the contact between an intrusive diorite and a limestone-quartzite flank pendant. The limestone has been metasomatized to form a calcium-magnesium skarn which, along the limestone / quartzite contact, has locally further developed into a mineralized magnetite-serpentine skarn. The principal copper minerals are bornite and chalcopyrite, with minor chalcocite and valleriite. Skarn gangue minerals are serpentine, diopside, garnet, epidote, calcite and wollastonite. Appreciable values in gold with some silver are present and recovered as well."

Jan 1, 1981

By Kyle Paulsen

The Cameco Key Lake mill began processing U-bearing waste rock from the McArthur River mine in 2000. This ore often contains elevated levels of calcium (>4% by mass), resulting in less than favourable conditions in parts of the Key Lake mill, yet still contains U3O8 at a concentration of about 0.3%. To recover the U3O8 and reject as much calcium as possible, modifications were made to the grinding circuit in late 2007 to include a gravity concentrator. The concentrator allows this mineralized waste to be processed separate from the regular blend material, rejecting calcium and concentrating U3O8, thus improving the operating conditions in areas such as SX. This will be presented in greater detail along with results and further work.

Aug 1, 2010

By Theo Mayer

Presentation Outline Define data visualization in the context of workflow Present other industries? application and demonstrated benefits Provide conceptual tools to help you address a visualization strategy Hold 10,000 foot view ? to touch on many issues

May 1, 2008

By H. Utsunomiya, Mehdi Sanjari, Abu Kabir, Steve Yue, Jing Su, L. Kestens, In-ho Jung

The microstructure and texture evolution of low temperature rolled AZ31 magnesium alloy during annealing were investigated. The specimens were rolled at the temperature of 100? at a high rolling speed of 1000m/min with a reduction of 30% in one pass. Annealing was conducted at various temperatures ranging from 200? to 500? for different time. To study the effect of fast speed rolling, the same annealing procedures have been applied for the specimens rolled at a significantly lower speed of 15m/min. The microstructure was characterized by optical microscopy and scanning electron microscopy, while the texture was analyzed by X-ray diffraction analysis and electron backscattered diffraction analysis. Texture weakening occurred during annealing at both fast and slow rolling speeds. However, at the same annealing condition, fast rolled specimens always had weaker intensity of basal texture than slow rolled ones.

Jan 1, 2014

By P. A. Verhey

"This paper describes a series of wear-resistant ceramic materials which have been successfully used in the mineral processing industry in Canada. Applications include use with metallic ores, coal, potash and asbestos, and in other processes where wear degradation is of major concern. The paper will also deal with considerations involving the selection of the different ceramic materials available. It will cover the installation of ceramic materials on support structures under varying process ' conditions, as well as the other physical and chemical factors which have to be taken into account.IntroductionIn the mineral processing industry, large volumes of ores tailings and other materials are handled. The abrasive nature of most of these materials results in extensive wear to both handling and processing equipment.Wear ratios versus cost, production losses due to down time and wear-resistant material suitability for a given application all demand particular attention when viewed against the need for increased efficiencies in existing processes. As a consequence, a very active continuous search for materials with improved wear resistance has been carried out for many years.In this search, starting about 20 years ago, dense ceramic materials were tested and evaluated in certain applications, notably in the iron ore and asbestos operations in Eastern Canada. As a result of substantially better performance both in continuous extended life and ultimate economics realized , wear-resistant ceramic applications developed progressively in many other processing applications, replacing traditionally used materials.In the vast majority of wear-resistant ceramic applications, considerable extended life over previously used materials was established. This invariably was not just a fractional increase but, in most cases , in factors of double, triple and often all the way up to 18 and 20 times the life of alternative materials used previously. In certain applications, extended life could not be measured and appears to be indefinite.Obviously, as a result of such experiences, the progressively wider use of wear-resistant ceramic materials is now an established trend."

Jan 1, 1981

By Rodney S. Read

This paper outlines a reasoned argument why no large-scale fracturing or faulting will be induced in the host rock by a deep geological repository (DGR) for nuclear fuel waste. Four DGR designs in three possible host rocks, including crystalline and sedimentary rock types, are considered. The reasoned argument draws from results of previously conducted thermal- mechanical analyses and new scoping calculations, along with evidence from experiments conducted in Canada and elsewhere. It is concluded that large-scale fracturing in the far-field is implausible given the expected in situ stress conditions in relation to rock strength. Near-field damage development and fracturing are expected in DGR scenarios in the different rock types, but these near-field effects are not expected to lead to large-scale fracturing that could compromise the integrity of the DGR and surrounding rock mass. Additional analysis and characterization activities are recommended to further validate the reasoned argument. Thermo-poroelastic loading of the rock mass is identified as one possible driving mechanism that should be studied further.

May 1, 2009

By T. A. Lazier, C. S. Longley

"Paymaster Consolidated Mines, Limited, owns several groups of claims in various parts of the Porcupine district. The area in which mining has been carried on includes parts of lots 5, 6, and 7, con. 1, Tisdale township, and twelve adjoining claims in Deloro township to the south. Highway No. 67A between South Porcupine and Timmins crosses the property.The discovery of the Dome mine in 1909 caused a rush of prospectors to the district and in a few weeks practically all territory adjacent to the Dome was staked. At that time work was started on the West Dome, West Dome Lake, Apex, and Standard properties. These were consolidated in 1930 to form the present Company. Gold was produced from the West Dome Lake from 1915 to 1930, and from the Standard-Paymaster from 1922 to 1928. The total production of the previous and present companies from 1915 to November 30, 1946, has been 487,170 oz. gold and 149,342 oz. silver from 2,337,554 tons of ore."

Jan 1, 1954

By Andrew Cormier

"The Early YearsThe Grand Lake coal fields in New Brunswick undoubtedly can claim the distinction of being the first part of North America from which coal was mined and exported. The diaries of the Governor of Massachusetts during the first half of the 17th century clearly establish this fact. There is also a reference in the Massachusetts Colonial Records which indicate that coal exports to New England were carried on as early as 1639.It has generally been believed that Cape Breton mined and exported the first coal; but no account has yet been found to show that this took place earlier than 1676. Both at Grand Lake and Cape Breton the coal was near the surface and removed by hand.When the country passed entirely into British control, Joseph Garrison, a grantee of Maugerville in 1765 moved to Jemseg. While surveying the north side of Grand Lake he discovered outcroppings of coal on the shore of the lake and further inland along the banks of streams. It was he who named Newcastle Creek in reference to Newcastle in England, which was widely known for its coal mines. Joseph Garrison died in 1783, the same year that an influx of United Empire Loyalists increased settlement in Newcastle Creek in the area now known as Minto. Many Loyalists also settled on the shores on both sides of Grand Lake.At a number of points where streams cut channels through the overlying strata, the coal seams were exposed and it was at such outcroppings that the early operations were carried on. A tunnel was driven in the seam from the foot of the bank, affording both an outlet for the coal and natural drainage from the workings. The coal was loaded into boxes and wheeled over wooden tracks to a point on the surface where it could be dumped into wagons and hauled either direct to destination or to where it could be loaded into boats and conveyed via Grand Lake, Jemseg and Saint John river to points of distribution.In the latter part of the 18th century and first years of the 19th century, farmers were undisturbed by mining the coal found on their lands. This was soon to change and resulted in many years of contention between landowners and the Legislative Assembly.New Brunswick became a separate province from Nova Scotia in 1784 and the seat of government moved from Saint John to Fredericton in 1788. The new province had its first priorities; the establishment of counties, the building of roads, and the development of its natural resources. From 1805, records of coal and land development are fairly complete. These records show the increasing interest of the Province in developing the coal fields. This interest resulted in the granting of coal leases to many friends of the government, without any regard for the wishes of the farmers who owned and had occupied the land for many years. The farmers fought back with lawsuits and other forms of dissension but with little success. By the end of the 19th century there were very few farm operators left in the area."

Jan 1, 1992

By J. A. Finch, M. Mimezami, M. S. Hashemi A.

The adsorption of magnesium and calcium ions on sphalerite and pyrite is discussed. These ions are common in process water and often considered be detrimental in sulphide flotation. The study attempts to characterize the adsorption mechanism, which has been less studied than the oxide system. Generally for oxides metal ion uptake occurs when cations are hydrolyzed. Our findings reveal that magnesium and calcium adsorb on sulphides at pH below hydrolysis, but adsorption is not chemical. At higher pH, charge reversal occurs that does correspond to presence of hydrolysis products. Advances

Jan 1, 2009

By Jacques Nantel

Mechanical-electrical personnel are present in all phases of the mining industry; the coverage is broad and diversified. Concepts of energy accounting are reviewed to pinpoint the sectors with a large energy consumption. Four sectors are reviewed: underground hard-rock mines, underground soft-rock mines, open-pit mines and mineral processing. In each sector, five or six technical innovations are analyzed as to their contribution to a more efficient use of energy.

Jan 1, 1979

By Keith R. Vining

Solid fuel, usually coke or anthracite, is commonly added to ground iron ore fines in the pelletising process to reduce the amount of burner fuel required and the maximum firing temperature, while maintaining pellet strength and the productivity of the pelletising plant. However, the use of coke and coal contribute to the production of greenhouse gases (eg carbon dioxide) and are a source of NOx and SOx emissions. Utilising wood biomass / wood char is one methodology CSIRO Minerals is investigating as an alternative to coke and coal, as it is a renewable energy source that is very reactive, has a low ash content and the potential to reduce emissions of greenhouse gases from the iron and steel-making process. Previous work has established that charcoal can effectively replace coke in the sintering process (Lovel et al, 2005), and the following experimental work aims to demonstrate that it can also provide an adequate replacement for coke and coal in the pelletising process. The paper presents the results of an experimental testwork program comparing the behaviour of fired pellets containing traditional solid fuels and charcoal. The physical properties of the pellets are compared in terms of their compressive strength, tumble and abrasion indices and the reduction properties. A qualitative assessment of the pellet microstructures is also presented.

May 1, 2007

By F. A. Forward

"NINETEEN sixty-six is a year of unusual significance in our Institute and in our country. It marks two-thirds of a century of service by the Institute to the people of the mineral industry and two-thirds of the century that Sir Wilfred Laurier said ""belongs to Canada."" As we meet here today within the historic walls of Canada's oldest city, a city that looks back on three hundred and fifty years of progress, I am reminded that it is almost a third of a century ago -in April, 1934 -that here in Quebec I first attended an Annual General Meeting of the Institute. It occurred to me that it might be appropriate to examine briefly the change that the middle third of this century has brought in the affairs of the mineral industry and, with some trepidation, to consider the prospect for the third that lies ahead.Opinions differ as to the relative importance of factors that have been responsible for the expansion and growth of Canada in its first hundred years. Some will say that it has been due to the abundance and fertility of agricultural land, others to the early enterprise of the railroads, and financiers believe that the banking system has been a major factor; -the fisherman -the forester -the teacher -each has his own view. I suspect, however, that most of us here would subscribe to the thesis of T. A. Rickard -miner, author, imperialist -who wrote, a gene-ration ago, ""Trade follows the flag, but the flag follows the pick,"" and thus agree that the finest contribution to progress, to wealth, to extension of frontiers and to inter-national trade has been provided by the mineral industry."

Jan 1, 1966

By C. Pawlik, R. T. Jones

Cobalt occurs together with copper in the southern African copper belt, and a large portion of this cobalt ends up in copper smelting slags, mostly dissolved in oxide form. It is possible to achieve high recoveries of cobalt by reductive smelting of the copper slags, using some form of carbon as a reducing agent in an electric furnace. For example, a 40 MW DC arc furnace was operated at Chambishi Metals in Zambia from 2001 to 2008, and demonstrated cobalt recoveries of around 80% from slag to an iron-rich alloy containing copper and cobalt. The alloy was atomized prior to leaching. With the recent increase in demand for cobalt (and the resulting high metal prices), there has been increasing interest in this process route. There is also an alternative hydrometallurgical process for recovering the valuable metals from the slag. The choice between these process options requires a trade-off between capital and operating cost and environmental acceptability. This paper examines the potential for cobalt recovery from slags, and outlines various process options. INTRODUCTION Cobalt has had a number of important uses in society since antiquity, and its principal use has changed dramatically over time. Since at least 2250 BC, cobalt-based pigments (cobalt blue) have been widely used to colour manufactured goods such as glass and pottery. Later, cobalt became known for its magnetic and wear-resistant properties and high-strength alloys, and most of the cobalt produced was consumed in the production of cobalt-based superalloys. The greatest recent growth in cobalt demand is due to it being essential to the rechargeable lithium-ion batteries used in consumer electronic devices and increasingly to drive electric vehicles. Cobalt is usually produced as a by-product of copper or nickel. The copper belt in the Democratic Republic of the Congo (DRC) and Zambia supplies most of the world's cobalt production. In 2018, the DRC was expected to produce 90 000 tons of the world total of 140 000 tons of cobalt (Shedd, 2019). This paper focuses on the southern African copper industry, and specifically the cobalt that is able to be produced as a co-product from this. A BRIEF HISTORY OF SOUTHERN AFRICAN COPPER SMELTING Copper deposits in South Africa have been documented since at least 1685, when the Cape governor, Simon van der Stel, ‘discovered’ the 'Copper Mountain' at Springbok. South Africa's first public commercial mining company (imaginatively called the 'South African Mining Company') was established in Cape Town in 1846, to exploit the rich copper resources that were believed to exist in Namaqualand.

Jan 1, 2019

By T. Sun, J. Kou, C. Sun, China Railway Resources Group Limited

"The polymetallic sulfide ore in Jiama county of Tibet contains 0.78% Cu, 0.046% Mo, 0.31 g/t Au and 17.9 g/t Ag in average. However, heavy loss of valuable metals was observed using high-pH process and Butyl xanthate as the collector. In this paper, the flotation was optimized through the adoption of a novel collector C-7, which is a mixture of xanthate ester and thionocarbamate. This collector showed better flotation performance under weak base conditions. The recoveries of Cu, Mo, Au and Ag increased to 93.24%, 84.60%, 78.13% and 75.41%, respectively, under 15 g/t of C-7 at pH of 8.0. The adsorption mechanism of C-7 was investigated by micro-flotation tests, zeta potential measurements, FTIR analysis and adsorption quantity measurements. Chemisorption of C-7 on chalcopyrite surface is demonstrated with adsorption density 3.8 times higher than on pyrite.INTRODUCTIONXanthates are the most commonly used collectors of strong collecting ability for separating copper sulfide minerals from gangue in froth flotation. However, the selectivity of xanthates themselves is poor to realize separation of chalcopyrite and pyrite whose floatability are quite similar (Heyes & Trahar, 1977; Chandraprabha, Natarajan, & Modak, 2004). High pH process with xanthates as collectors is proved effective in copper-sulfur separation and is widely used in treatment of copper sulfide ore flotation (Smith, 1996; Valdivieso, Cervantes, Song, Cabrera, & Laskowski, 2004). This method could get ideal separation results, but large amount of lime must be added, and could bring about increased cost, device corrosion and environmental pollution. In addition, there could also be high depression and heavy loss of associated noble metal such as Mo, Au and Ag. Consequently, a large amount of research has been conducted on substitutions of xanthates for selective flotation of copper sulfide ores under low pH conditions (Gholivand, Khodadadian, & Ahmadi, 2010; Li, 2010)."

Jan 1, 2016

By Frank B. Amon

Highland Valley Copper had to make some significant changes in the way it was working in order to counter the effects of ever-increasing costs and decreasing metal prices. A mine/mill optimization plan started in 1997 introduced new technologies and management approaches that resulted in a dramatic drop in cash breakeven costs. The changes involved employee training, added authority and responsibility for staff, better communications, and a consistent approach to setting and achieving property-wide goals. The net effect was to change the culture of the organization from one that was fragmented and focussed on local objectives to one that is cohesive and has common goals. These changes have allowed the mine to remain in business during a protracted period of low metal prices, and have positioned the mine favourably to benefit even more from any future increase in prices.

May 1, 2004

By Michael Hood

An overview is given of some of the major mining research activities in Australia. Automation of mining equipment is not an objective in its own right. The objective is to improve the safety and the economic performance of mining operations. Automation can be a useful method for achieving this objective. There is a strong focus on mining equipment automation and related issues and specific examples of ongoing and recently completed automation projects are described.

May 1, 2002

By J. P. Harrison, G. F. Gambino

"This paper examines unpredictability in the parameters governing hydraulic fracturing (HF) as used in stress amelioration for underground excavations, with the aim of showing how this unpredictability may affect design decisions. Using uncertainty models that are appropriate to particular levels of information and degrees of uncertainty, this paper demonstrates how these can aid in decision-making related to feasibility assessments of HF arrays for stress amelioration.Cave mining operations produce large underground voids and high stress concentrations around critical mine locations. These stress concentrations increase the potential for rock burst events. Although de-stress blasting has a long history for redistributing high stress concentrations, to improve safety and reliability HF is now being trialled as an alternative.Unfortunately the HF process is extremely uncertain, and so predicting fracture propagation geometry is difficult. Although the major parameters governing HF propagation have been previously identified, no indication has been given regarding the contribution that uncertainty in these makes to unpredictability in the overall HF system. Using simplified models of HF and referencing a recently proposed characterization of unpredictability, we relate unpredictability in the various governing parameters to the effect it has on strain energy density (SED) in the surrounding rock. Within these models we analyse SED as well as the stress intensity factor (KIc) when investigating the effect of parameter uncertainty and its influence on various crack propagation criteria (Sih & Macdonald, 1974). These models are applicable to unpredictability associated with the development of new fractures; the case of pre-existing fractures is the subject of on-going work.The paper will assess in greater detail the various governing parameters, and investigate the appropriate use of other uncertainty models. As a result, we will show how assessment of uncertainty in HF parameters can be used to both guide feasibility studies and determine the optimal allocation of resources to improve the final design."

Jan 1, 2015

By W. A. Jones

"The Ross mine, a subsidiary operation of Hollinger Consolidated Gold Mines, Limited, is near the north end of lot 1, con. II, Hislop tp., Ontario. The property comprises the north half of lot 1, con. II, and the south onethird of lot 1, con. III. It is readily reached by a good motor road from the village of Ramore, 7 1/2 miles to the southeast on the Ontario Northland railway. The mine is being developed to a depth of 1,500 feet, and the current daily production rate is approximately 300 tons. From the inception of operations in March 1935 until December 31, 1945, 692,000 tons of ore, with a total value of $5,762,685, was milled . The silver to gold ratio of 1.48 to 1 is unusually high for Ontario gold mines.TYPE OF 0REBODIES AND MINERALIZATIONThe orebodies consist of lens-shaped and pipe-like stringer lodes and tabular vein zones composed of parallel quartz stringers. The host rocks are steeply inclined eruptive breccias and tuffs, striking N.70°W., intruded by very small stocks of red syenite. The orebodies appear to be spatially related to an intricate system of fault planes. Hydrothermal alteration is widespread and is not zonally related to individual quartz stringers. The wall-rocks contain abundant fine-grained pyrite, but gold is confined to the quartz stringers.RELATIONSHIP TO REGIONAL STRUCTURELack of outcrops has prevented the detailed mapping of the Keewatin complex in the vicinity of the Ross mine with the degree of success that has been achieved in the Porcupine area.A northwesterly trending belt of slates and greywackes, bounded by faults, forms the central part of a broad anticlinal arch about 3 1/2 miles north of the Ross shaft. Lava flows forming the south flank of the structure face south toward the mine. If the sediments are to be tentatively correlated with the large areas of Keewatin slates and greywackes of the Porcupine area, it must be assumed that they are younger than the lava flows and that they have been down-faulted."

Jan 1, 1954

By V. Pouyafar

Semi-Solid metal alloys, as used in SSM processing, have a special microstructure of globular solid particles suspended in a liquid matrix, which makes them behave differently in forming processes. The sensitivity of semi-solid slurries to temperature variations and their history and rate dependant behavior, make process design and control difficult. Precise selection of the process parameters is necessary in part production. Therefore, a numerical analysis and simulation of the process can be a valuable tool in process design. In this work we proposed a structural dependent model to account for the thixotropic behavior of semi-solid metals. The parameters of the model were then determined using rheometery tests. The results show a good agreement between the model and the experiments.

Oct 1, 2011