Search Documents

By Robert K. Jonas

Mining companies can improve production and reduce costs by using the best available technology to control their operations. Many mines are challenged to use multivariable predictive control due to limited experience or staffing, as well as being concerned over the robustness and sustainability of predictive controls. As a result many mines are not realizing optimal performance from their assets, and thusly are not realizing the production increases or cost reductions that this technology can deliver. Over the past few years, the application of multivariable model-based predictive control has gained acceptance in many mining processes and has proven to be robust and sustainable for some of the most challenging mining processes. New automated modeling and performance monitoring software have greatly simplified the effort to implement and maintain these solutions. In addition, many progressive companies have chosen to co-source the implementation and service of these solutions to assure project success and continued benefits stream. This technology has been successfully applied to a wide variety of processes; grinding mills, alumina digestion, CCD washer and thickeners, kilns, calciners, roasters, flash smelters, heat exchangers, evaporators, and most recently in the demanding process of flotation. This paper discusses the state-of-the art in advance control technologies in the mining industry, including the impact of these technologies on maximizing benefits, and implementing best practices for long term sustainability. Benefits from recent multivariable predictive control applications in copper mining will be reviewed, and the use of the latest predictive control technologies and practices in mining will be discussed.

Oct 1, 2009

By A. Bauer, P. Katsabanis, M. Baker

The principal results from a previous paper presented at the Mine Accident Prevention Association of Ontario in 1987 (1) are summarized here. It is concluded that the selection of explosives in mines experiencing sulphide ignitions is important and that aluminized explosives should be avoided because of their high explosion temperatures and their detonation products. The duration of the blast is also critical and secondary blasts should not occur simultaneously with nearby priroa:ty blasts.

May 11, 1988

By D. J. M. Farnsworth

Since the 1.940's, the bulk of the ore production from the Sullivan Mine has come from pillars. These pillars, located from 100 to 2000 feet below surface, have been subjected to considerable ground pressure. Mining techniques were adopted to minimize the problems of deteriorating ground conditions. These techniques included an orderly sequential blasting of pillars along a retreat front, stage blasting of tall pillars in horizontal slices and utilization of broken pillars as "buffers". The latter two techniques involved leaving substantial tonnages of broken ore in place for as long as 4 years. Rapid oxidation of metal sulphides, with attendant heat and noxious gas generation, had occurred in a few very localized areas of the mine associated with a major water course. However, in a very short period starting in 1972, sulphide fires spread to several of the large blocks of broken ore that had been left inactive for lengthy periods. There proved to be no feasible method of extinguishing these fires, except by complete removal of the burning ore. The attendant problems of handling large tonnages of burning ore have had considerable negative impact on the mine operation. The chemical reactions involved in these sulphide fires have been studied by the mine staff to determine the conditions necessary for' initiation and propagation of the tires. Techniques to safely and efficiently handle hot ore have been implemented and refined. Lastly, and most important, mining methods at the Sullivan Mine have been revised to ensure that additional fires do not occur.

Jan 1, 1977

By D. A. McIsaac

In these days, when mass production seems to be the watchword of all industrial companies, nothing is left undone to attain this end. Transportation, where necessary, becomes a question of very great importance. For this reason every mechanical contrivance known to man is employed, with its resultant advantages. So successful has man's ingenuity been that, offhand, we are inclined to say that practically all transportation on a large scale is done mechanically, that is, where speed and economy are desiderata. Granting this, one would think that to read a paper on the horse before your honourable and highly technical Society would surely be a waste of time, and that any Company employing old-fashioned 'horse' power would certainly be very much behind the time, to say the least. However, the fact remains that the biggest industry in our country today-coal mining-must use horse power to a great extent, being compelled -both by considerations of economy and by necessity. For this reason,' in the production of coal under present conditions, the pit horse is of great importance to this industry and is to be considered seriously as one of the units that help to make coal mining a success or a failure. Hence, in employing horses as a power for transportation, care must be exercised in selecting the animals, and the care of this power must be considered as seriously as any other department of such an organization. In selecting a pit horse, several things must be borne in mind, that is, one must get as much horse power as possible in as compact a form as is practicable. This determines the type of horse we must use, which is of very great importance under our present conditions of coal mining. With low roof, steep grades, and forced production, a distinct type of animal must be selected.

Jan 1, 1930

By Yongjie Bu, Wei Sun, Zhiyong Gao, Yuehua Hu, Hongbiao Tao, Runqing Liu, Central South University

"The flotation behavior of O-isopropyl-N-ethyl thionocarbamate (IPETC) and pH for chalcopyrite and galena was studied through pure mineral test, adsorption quantity determination, solution chemistry calculation and Materials Studio simulation. The results show that the recovery differential value of chalcopyrite and galena is about 20% when pH of the pulp 9.5 and IPETC is 7×10-4 mol/L, the flotability differences of the two minerals is significant. There is competitive adsorption between OH? and IPETC on mineral surfaces, it lead to galena flotability is lower than chalcopyrite flotability. IPETC can remove the hydration layer on mineral surface and adsorb on active sites for collector adsorption, minerals have a better hydrophobicity.INTRODUCTIONCopper and lead are two of the most widely used metals in industrial and living, their applications include building construction, various metal alloys, heat and electricity, machine manufacturing (Zhang et al., 2014). Chalcopyrite and galena are the major source of copper and lead, normally they associated with each other. With the growing use of these resources, high grade and dissemination large particle sizes minerals are less and less, the use of low grade and complex dissemination minerals have to be paid more attention (Chen, Ye, & Li, 2010; Liu, Sun, Hu, & Wang, 2009). As the special properties and complex composition of copper-lead sulfide ore, flotation separation of chalcopyrite from galena effective is a research emphasis and difficulty point in mineral processing (Bruckard, Sparrow, & Woodcock, 2011).In the separation process of chalcopyrite and galena, it is rather important to choose effective collector (Huang, Wang, & Liu, 2014). Enlarging and using the two mineral flotability will be a good basis and start in flotation (Reyes-Bozo et al., 2014). Qin et al. (2013) made a great deal of research on flotation separation of copper/lead concentrate, collector O-isopropyl-N-ethyl thionocarbamate (IPETC), butyl xanthate (BX) and ammonium dibutyl dithiophosphate (ADTP) were investigated, BX and ADTP floated both chalcopyrite and galena well, specific adsorption appeared in the surface of mineral, the problem was the collectors were not selective enough, however IPETC showed better selective."

Jan 1, 2016

By H. L. Ramandi, P. Moore

"The corrosion of support bolts in underground mines has become an increasingly prevalent issue over the past two decades. With an increase of premature failures due to Stress Corrosion Cracking (SCC), it is evident that understanding the environmental factor influencing the cable bolt corrosion is critical for maintaining effective ground support hence the safety and productivity of underground spaces. Experimental testing of rock and cable bolts were accomplished in a variety of packings, including saturated clay, saturated coal, mine water and grout/cement to investigate their corrosion behaviours. Water samples were obtained and analysed for pH and electrical conductivity (EC) during the experiment. After a period of 76 days the bolts were retrieved and analysed visually. Primary factors were found to be the presence of geological materials and the aeration of the bolts, i.e. the vicinity to air and air flow, while secondary factors were observed to be pH levels and EC. It was also found that the coal/clay interfaces and the water/grout/cement interfaces are non-relevant to corrosion of rockbolts and cable bolts. The proposed framework can be applied to other reinforcement materials used in underground spaces for improved understanding of corrosion environment.INTRODUCTION Rock bolts and cable bolts are the major reinforcement elements used in mining industry to improve the rockmass properties for safe and productive mining. They are normally used to pin large beams or blocks of rock in underground mines to stabilise the rockmass in the roof (strata) against collapse. The rockbolts are typically low cost hot rolled rebar while cable bolts are composed of strands of wire, normally wound together around a central king wire (Hyett and Bawden, 1993; Vandermaat, 2014). The typical length of the bolts in underground mines is 2.4 m and 4–12 m for rockbolts and cable bolts, respectively (Vandermaat, 2014; Windsor and Thompson, 1997). Cable bolts are much more flexible and usually offer a much higher load capacity than rigid rockbolts. Their increased length and flexibility allows cable bolts longer than the height of a roadway to be used in underground mines."

Jan 1, 2017

By J. J. Benitez

MIBC (methyl-isobuthyl carbinol) was previously shown to enhance significantly sylvite flotation when used at the stage of preparation of amine dispersions. In this paper Atomic Force Microscopy (AFM) is used to study the effect of MIBC on deposition of octadecylamine (ODA) on the surface of mica. The AFM images indicate that amino terminated, and therefore hydrophilic, deposits of ODA are observed on the mica surface in the ODA dispersions free of MIBC. In the presence of MIBC a methyl terminated (hydrophobic) monolayer is obtained on the mica surface. The transition between the monolayer and bilayer phases is due to the presence of MIBC. Experiments carried out in distilled water reproduced the results obtained from the brine. Working in pure water instead of brine simplifies the preparation conditions and the analysis by AFM.

Jan 1, 2006

By R. J. Rotzinger

The Gibraltar Mine and Mill facility were commissioned in 1972 by Gibraltar Mines Ltd utilizing a flowsheet consisting of two stages of crushing followed by a rod mill / ball mill grinding circuit. During operations a number of opportunities were evaluated to expand the mill capacity; however, the economics of the day did not allow any of these projects to proceed. The mine continued to operate until late 1998 when it was shutdown and put on care and maintenance due to low commodity prices. Taseko Mines acquired Gibraltar in 1999 and in 2004, with the improvement in the metal markets, made the decision to restart operations. During the restart planning a number of opportunities for mill improvements and upgrades were identified and, after operations were successfully restarted, the decision was made to once again review expansion opportunities for Gibraltar. Taseko evaluated various expansion alternatives eventually deciding to install a SAG Mill, convert the existing rod mills to ball mills and distribute the SAG discharge to the resultant six 6 parallel ball mills. This paper discusses the design, implementation and commissioning of the SAG mill grinding circuit.

Jan 1, 2012

By A. Ghahreman

Activated carbon is proven to be able to catalyze arsenic oxidation in aqueous solution under acidic conditions. A commercially available granular coconut shell based activated carbon (AC) has been evaluated for catalysis of arsenic oxidation in this study. The rapid small-scale column test (RSSCT) has been developed to simulate and predict the performance of a carbon-based arsenic treatment system in a pilot scale reactor. Effects of residence time, aeration rate, and initial arsenic concentration in the influent solution on the AC catalysis of arsenic oxidation under dynamic and continuous conditions were studied by manipulating these parameters during RSSCTs. The effectiveness of the AC on arsenic oxidation was examined over the course of constant diffusivity based RSSCT operation. Residence time and initial arsenite concentration are proven to be the most effective impacting parameters on the arsenic oxidation process. For the 218 min residence time, the highest steady-state arsenic oxidation efficiency achieved was 98% with 1 g/L As(III) being treated at pH=1 under 0.05 L/min oxygen aeration. In a long-running RSSCT, the oxidation efficiency did not seem to deteriorate over a course of 666 hours operation, corresponding to 13986 mL total influent throughput volume. INTRODUCTION Arsenic is toxic to both animals and plants and inorganic arsenicals are proven carcinogens in humans. The increased extraction of low grade and complex mineral resources has introduced high ratios of arsenic into metallurgical processes. Discharge of arsenic by acid mine drainage resulting from mining activities has added intensive pressure on the need for proper treatment (Lawrence & Higgs, 1999). Since trivalent arsenite is more toxic and has lower affinity to solid surfaces for adsorption, many treatment systems initiate with an oxidation step to convert arsenite to arsenate and reach the ultimate immobilization of arsenic by the following precipitation of arsenate (Nazari, Radzinski, & Ghahreman, 2016). Scorodite precipitation has been studied extensively as a means of arsenic immobilization due to its high stability and negligible potential of releasing arsenic (Filippou & Demopoulos, 1997). As a stable ferric arsenate mineral, crystalline scorodite can contain up to 30 wt% arsenic (Paktunc, Dutrizac, & Gertsman, 2008). Arsenic must be in its pentavalent oxidation state in order for scorodite to be precipitated via oxidizing ferrous ions (Clancy, Hayes, & Raskin, 2013).

Jan 1, 2019

By Masayuki Ishikawa

In a radio frequency and optoelectoronic device packaging, Gold-Tin (Au-20 wt% Sn eutectic) solder is used widely due to the excellent electrical and thermal conductivity, high strength, and negligible creep characteristic under repetitive thermal cycling. With the recent lead-free movement, Gold-Tin solder is recognized as an alternative material for high temperature Lead-Tin solder. Generally, Gold-Tin solder is supplied in the forms such as ribbons, pellets, and ring frames. However, these forms must be set-up accurately on the joint area to press chips in bonding, therefore, it is difficult for these forms to satisfy the recent requirements for the down sizing in the connection areas. On the other hand, Au-20 wt% Sn solder paste can be applied flexibly to various supplying methods, such as printing, dispensing system and pin transcript. These methods also make it possible to reduce the production cost. However, in the case of using the solder paste, the void issue is one of the most undesirable problems. The void causes the degradation of the characteristics such as the bond strength, electrical characteristic and thermal conductivity. We have been intensifying the development of the void free paste, and have achieved void reduction by optimizing the powder size, the flux composition and the reflow condition.

Oct 1, 2003

By H. J. McQueen

Aluminum was hot worked at 400 - 500°C and strain rates (e ) of 0.004 -0.1s-1, under reversing strains (c) of 0.5 to 0.2 or 0.5 to 0 and also advancing from 0.5 to 1 or 0.5 to 5. Under similar test conditions for different parts of the strain paths, the average measured flow stresses are found to agree with each other. In the forward and backward strain path tests, the almost identical steady state plateaus affirm the occurrence of dynamic recovery (DRV). On reversal of strain direction at constant e , there was generally negligible Bauschinger effect. In specimens annealed at 400°C, static recrystallisation (SRX) was followed microstructurally. mainly by disappearance of elongated grains with serrated boundaries because the new grains were only little a finer than the old due to low strain energy. The only influence of reversing strain path observed was the effect of change of grain boundary area as grains elongated or returned towards equiaxed. In optical microscopy, elongated grains with serrations and deformation bands confirmed DRV in forward path specimens. In reverse path specimens, equiaxed grains were gradually restored with retention of serrations and bands. In low magnification polarized optical microscopy, grain alignment increased with strain for forward path specimens; whereas it decreased in reverse path ones, supporting DRV. Orientation imaging microscopy (OIM/SEM) revealed that elongated grains are broken up as deformation bands rotate during the forward path and that grains return to equiaxed appearance on backward straining. Comparative studies using optical microscopy in polarized light (POM), OIM/SEM and transmission electron microscopy (TEM) revealed that while subgrains remain equiaxed and constant in size and character during the forward and backward paths, the fraction of low angle facets decreased while that of high angle grain facets increased with increasing strain; these are coupled with a fairly low fraction of medium angle boundaries. The results contribute to the understanding that dynamic recovery in aluminum maintains sub-boundaries with low misorientation but as grains elongate and more subgrain become adjacent to grain boundaries the fraction of high angle boundaries rises (with backward straining it was vice versa).

Jan 1, 2007

By D. A. McIsaac

In these days, when mass production seems to be the watchword of all industrial companies, nothing is left undone to attain this end. Transportation, where necessary, becomes a question of very great importance. For this reason every mechanical contrivance known to man is employed, with its resultant advantages. So successful has man's ingenuity been that, offhand, we are inclined to say that practically all transportation ?On a large scale is done mechanically, that is, where speed and economy are desiderata. Granting this, one would think that to read a paper on the horse before your honourable and highly technical Society would surely be a waste of time, and that any Company employing old-fashioned 'horse' power would certainly be very much behind the time, to say the least. However, the fact remains that the biggest industry in our country today-coal mining-must use horse power to a great extent, being compelled both by considerations of economy and by necessity. For this reason,' in the production of coal under present conditions, the pit horse is of great importance to this industry and is to be considered seriously as one of the units that help to make coal mining a success or a failure. Hence, in employing horses as a power for transportation, care must be exercised in selecting the animals, and the care of this power must be considered as seriously as any other department of such an organization. In selecting a pit horse, several things must be borne in mind, that is, one must get as much horse power as possible in as compact a form is practicable. This determines the type of horse we must use, which is of very great importance under our present conditions of coal mining. With low roof, steep grades, and forced production, a distinct type of animal must be selected.

Jan 1, 1930

By N. Djilali

Many of the transport phenomena encountered in proton exchange membrane fuel cells occur intrinsically at the microscale level. Physically representative models that fully account for the salient physico-chemical and transport processes in PEM fuel cells are necessary to achieve truly predictive models that can be used with confidence to: (i) gain a better understanding of in-situ processes and couplings, (ii) explore new concepts, and (iii) support design and optimization. The development of more general, rationally based macroscale models requires use of knowledge on the microscale level to provide guidance, and to determine the required parameters and coefficients (model "constants"). In this paper we present a new membrane transport model, the binary friction membrane model (BFM2), recently developed to account for coupled protonic and water transport in polymer membranes. This general model is based on rational and physical consideration, removes several of the limitations of the empirical models used to date, and is formulated for all purfluoro-sulfonic acid membranes. The use of the BFM2 in a fuel cell model is illustrated highlighting significant performance predictions compared to existing empirical model. The second part of the paper addresses the fundamentals of two-phase transport in hydrophobic gad diffusion media. Computational and experimental visualizations resolving the microscale dynamics of water transport between the fibres of a GDL are presented, revealing transport mechanisms that are, contrary to assumptions used to date, dominated by fingering and channeling.

Jan 1, 2005

By T. Hofbauer, M. J. Dry, G. B. Harris, C. W. White

"Urban Mining is a term that is increasingly being used, and represents an appreciable source of secondary materials for the metals extraction industry, a source that does not incur mining costs, but does, at present, incur considerable disposal costs. Electric Arc Furnace Dust (EAFD) is probably the most common of these materials, with an estimated global production of 8 million tonnes annually, of which 1 million tonnes is generated in North America. The contained annual metal value in EAFD at current prices is of the order of $6 billion, yet, apart from the zinc, virtually none of this is recovered.Despite many attempts over the years, with pyrometallurgical, hydrometallurgical or hybrid processes, currently the only commercially viable method of treating these materials is smelting in a Waelz Kiln (or a Rotary Hearth Furnace), which essentially recovers only the zinc, in an impure oxide form, and generates a secondary slag waste, which is still toxic and requires disposal. This paper describes the development of a chloride-based treatment process to recover all components of the EAFD in a marketable form, which centres around the novel hydrochloric acid recovery and recycle operation. Laboratory, miniplant and pilot plant data are presented, leading to the definition of a viable process flowsheet enabling the recovery of pure iron and zinc products (the principal components of EAFD), together with secondary products such as copper, silver, lead, cadmium, magnesium and manganese. A rigorous mass-energy balance is used to examine the preliminary economics involved."

Jan 1, 2014

By J. Suarez Condezo, E. Herrera Alarcon

The Ilo Smelter Modernization Project will require treating the slag from the Peirce Smith converters in Slag Cleaning Furnaces using pig iron technology. Currently the slags from the converters show variable magnetite contents. The copper contained in this slag is recovered in Reverberatory Furnaces, where the smelting rate was improved due to the high silica content of the converter slag. Preliminary industrial tests where developed to clean the slag from converters using pig iron. The results showed that the magnetite content has a significant influence in this process. This work describes the actions that are being implemented in the converter operation to control the magnetite content in the slag in order to maintain the high copper recovery of the smelter when the new facilities are commissioned. This task will demand a strong control of both the slag chemistry and converter practices in order to get the copper recovery considered as the design criteria (~97.4%).

Jan 1, 2007

By M. Mahdi, L. So, A. MacMillan, D. Metcalfe, J. Woloshyn, D. Sauter, N. Uys, JP. Janse van Rensburg

For city smelters, with limited real estate, efficient slag cleaning furnaces followed by water granulation to produce an iron silicate product is the preferred process approach. Water granulation, however, consumes large volumes of water and requires high maintenance due to abrasive slag/water slurries. Air granulation offers an alternative to water granulation, which eliminates water use and has low maintenance requirements. Although full-scale operation has not been implemented for copper slags, full-scale operation for platinum group metal (PGM) converter slag has been implemented. A review of full-scale air granulation performance for PGM converter slag is provided. Based on PGM converter slag granulation performance, parallels to copper slag granulation are drawn and full-scale operation for copper slag is modelled using computational fluid dynamics (CFD). INTRODUCTION Typical slag management practices in the copper industry include dumping, slow air cooling, and water granulation, as shown in Figure 1. Dumping is the most commonly used slag handling method for most metal production plants, but presents challenges including the requirement for a large slag pit, requirement for expensive/high-maintenance “hot” mobile equipment, risks associated with transportation of molten slag, and no value recovery from slag as a sellable by-product or from slag as a source of heat.

Jan 1, 2019

By Quenton Johnson, W. A. Gough, David Carr

"This paper describes the application of the BrainWave Model Predictive Controller (MPC) and Advanced Control Expert (ACE) Advanced Supervisory Control System on the SAG Mill, Ball Mill, and Rougher Flotation cells for a new gold processing line at the Oceana Gold - Haile Gold mine in Kershaw, South Carolina. For this project, ANDRITZ supplied the control system design and programming, operator-training simulator and advanced control. The advanced control was tested against the IDEAS™ dynamic simulator, and commissioned during the startup of the processing plant to help achieve target production as quickly as possible. Operators were able to run the equipment in a consistent and optimized manner from an early stage of the plant operation, increasing efficiency and profitability. MPC is able to reduce process variability beyond the best performance that can be obtained with conventional Proportional Integral Derivative (PID) control methods. MPC is able to optimize the control of processes that exhibit an integrating type response in combination with transport delays or variable interaction, which are characteristic of many gold processes including SAG mill weight control and Flotation cell froth level control. The experience and benefits of applying MPC during the startup of a new gold processing plant are presented in this paper.INTRODUCTION Mineral processing operations present many challenges for automatic process control due to variations in unmeasured ore properties, material transport delays, and non-linear response characteristics. Advanced process control technologies such as expert systems and multi-variable model predictive controllers are often used to improve the control of these processes to increase productivity and recovery efficiency. Typically these systems are applied after the mine has been in operation for a period of time. For this project, a complete dynamic process simulator was developed using the IDEAS platform for the purpose of training operators before the plant was constructed. Operators were able to become familiar with the process and the control system in order to become proficient in the use of the controls before the plant was ready to start. They were able to practice abnormal condition management including startup and shutdown of the process using the simulator and develop complete Standard Operating Procedures (SOPs) for these situations. The simulator was also used to test the control system functionality and operator Human Machine Interface (HMI) configuration to reduce errors and improve the performance of the control system during plant start-up."

Jan 1, 2017

By T. Iwasaki

This paper points out two key elements in resource trade in general and the Canada-Japan relationship in particular. The first is that the advanced countries have a more important role than one would expect in the supply of resources in world trade. Canada 's dual role as a major resource supplier in conjunction with an advanced economy will continue to increase. The second point is the heavy reliance on foreign resource supplies in some advanced economies, particularly in Japan. Finally, as regard the future of the Canada-Japan economic relationship, particularly .in resource development, it is suggested that trade could be enhanced by an accelerated exchange of various types of resources between the two countries. These include natural resource commodities as well as the more abstract capital, technological and human resources.

Jan 1, 1978

By R. J. Goodman, P. Lafleur

This paper presents a current interpretation and projections of recent statistics on raw materials availability based on familiarity with the Canadian steel industry and its development. Problems and opportunities are recognized and discussed.

Jan 1, 1976

By L. Li

Backfill is increasingly used in underground mines, as it can help reduce the environmental impact from mining operations. However, the primary objective of backfilling is to provide safe working space for miners, by improving ground stability conditions. As cement is often added to the backfill, a critical issue is the determination of the required backfill strength (cohesion) due to the binder. This value is usually obtained from a solution proposed by Mitchell and co-workers, in the early 1980?s, for stopes with an exposed backfill face. This paper presents a brief review of the Mitchell et al. solution, with some of its main limitations. Some of the recently developed solutions for backfill design are then summarized and discussed.

Aug 1, 2013