Search Documents

By Jennifer Pakula

Productivity improvements in underground mining are becoming harder to find. Most mines quickly identify deficiencies in their processes and then struggle to make productivity gains beyond that plateau. One way to increase productivity in this situation is to modify existing methods of operation. Vale?s Stobie Mine has been in operation since the late 1800?s employing a variety of mining methods. Many mining advances have been incorporated over time. With the advent of mechanized rubber tired equipment, sublevel cave mining was introduced to allow economic extraction of a large low grade area. Additional productivity gains were seen in the sublevel cave area with the introduction of preloading production drill holes. In preloading, the holes are loaded with bulk emulsion ahead of the production cycle and then primed for blasting as needed. The introduction of preloading, although giving the Stobie sublevel cave process an overall productivity gain, saw an increase in oversize due to the collar priming technique employed. Handling oversize material prohibited the operators from handling additional units of optimally sized material. Prepriming, adding detonators at the toe and midcolumn of the production holes during the preloading process, was identified as a change that could reduce the formation of oversize. This paper describes the introduction of prepriming to the sublevel cave mining method and focuses on the process Stobie employees followed to ensure a safe transition to this productivity improvement.

Nov 1, 2011

By D. C. Carter, J. P. Anderle

"Exploration drilling of evaporite sequences in eastern Canada has undergone significant changes in equipment, techniques and philosophy since the early 1970s. The result has been the recovery of full-size cores from properly conditioned and stabilized holes, high quality open hole geophysical logs, and high quality metallurgical samples. The majority of modifications have resulted from the necessity to preserve the integrity of the evaporite deposit, and thus ensure the potential development, combined with the need for cost-effective high quality information. This is particularly evident in the priority placed on the development of non-erosive drilling fluids, casing and cementing procedures. The results are applicable to diamond drilling exploration of evaporite deposits anywhere in the world.IntroductionThe majority of current technical and scientific literature and expertise available on such subjects as drilling fluids or cementing procedures is applicable to large diameter, deep (several thousand metres) oil-field type drilling . The differences between oil-field drilling and wire-line core diamond-drilling are dramatic: large diameter, deep holes drilled with a low rpm tricone bit using large volumes of fluid pumped through a large annulus versus small diameter, shallow (less than 600 m) holes drilled with a high rpm diamond-set core bit using small volumes of fluid pumped through a small annulus. Exploration drilling of evaporite sequences in eastern Canada in the early I970s was conducted using oil-field equipment and techniques to complete holes of moderate (1000 m to 1500 m) depth . The prohibitive cost of these operations has necessitated that subsequent exploration drilling employs modified diamond-drilling equipment and techniques developed as part of a transition away from oilfield methodology. The result has been full size core, recovery approaching 1000/0 and the ability to run open hole geophysical logs; a combination of factors enhancing the collection of high quality information (Carter, I989a)."

Jan 1, 1990

By S. Masambi, S. M. Bradshaw, C. Dorfling

The presence of iron in base metal leach solutions complicates nickel and copper recovery processes. Leach solutions are commonly purified by precipitating iron as hematite, jarosite or goethite. Fast oxidation of ferrous to ferric is an important step to remove iron by precipitation at low pH values. This study reviews the ferrous oxidation mechanism and reaction rates in chloride media using molecular oxygen. This work contributes to the development of a better understanding of iron precipitation processing steps, which continues to be an important matter in hydrometallurgy. The specific objectives were to investigate (1) the effect of key process variables (acid concentration, copper concentration, and temperature) on the rate and extent of ferrous oxidation by dissolved oxygen and (2) the oxidation mechanism by varying chloride and hydrogen ion concentrations separately. Batch oxidation tests were performed using synthetic chloride solutions containing 45 g/L Fe and 3 g/L Ni at 50 and 80°C, dissolved Cu concentrations (0.3 to 3 g/L) and HCl concentrations (2 to 4.6 M). Regression analysis indicated that the significance of the effect of different variables on the extent of oxidation achieved after five hours decreased in the following order: HCl concentration > Cu concentration > temperature. Increasing the HCl concentration from 4 M to 4.6 M caused the degree of oxidation achieved after two hours to increase from 58.3% to 98.1%. The catalytic effect of dissolved copper on ferrous oxidation was more significant at low acid concentrations. Experimental data suggest that rapid oxidation of ferrous is possible at high HCl concentrations for two main reasons. First, the formation of ferrous chloride complexes allows ferrous oxidation to proceed without the formation of superoxide as an intermediate product (the rate limiting step in dilute acid solutions). Second, the formation of ferric chloride complexes stabilises the oxidation product.

Jan 1, 2016

By Euler M. De Souza

"This paper presents a study developed to assess the potential use of salt tailings as backfill to control surface subsidence and as a mine bulkhead used to isolate areas of potential brine inflows. A series of index tests, centrifuge model tests and quasi-static creep consolidation tests were performed to evaluate the creep and consolidation properties of salt backfl1l and to evaluate the effect of brine inflow and brine infiltration on backfill behaviour. The centrifuge models were specifically designed to study the mechanical behaviour of salt backfill under the influence of brine inflow and long-term creep. Test results indicated that salt tailings could be applied underground as a bulkhead to seal off areas of potential inflow with the additional advantage of controlling room closure and local back instability. It is hoped that this study will assist mine planners to develop contingency plans to control brine inflow occurrences. IntroductionThe use of salt tailings as backfill is a technique that would assist in the control of potential brine inflows and surface subsidence, and would have a very positive impact on the long term adverse environmental effects associated with surface salt tailings disposal. A centrifuge testing program was designed to evaluate the behaviour of salt tailings as backfill; the effectiveness of salt backfill as a bulkhead used to isolate areas of potential brine inflow and the potential use of salt backfill to control surface subsidence. The testing program was also used to evaluate the creep-consolidation properties of salt backfill and to evaluate the effect of brine inflow and brine infiltration on backfill behaviour. This paper presents the results of the experimental centrifuge testing program and a comparison of results with models tested under I g using an electrohydraulic servo-controlled loading frame (MTS) and a creep consolidation cell. Applicability of the results to practical underground soft rock mining is also discussed.The centrifuge model tests indicated that salt tailings could be applied underground as bulkheads to seal off areas of potential inflow with the additional advantage of controlling room closure and local back instability. Because the applied stresses (1.2 MPa) and fill consolidation were relatively low, the centrifuge simulated bulkhead did not retain all of the inflow brine. At typical field stresses it is expected that the fill would be able to seal off panels with brine inflows. Further testing at higher stresses are suggested to determine the consolidation and stress levels at which the fill would completely retain any potential brine inflow head and positively act as mine bulkhead."

Jan 1, 1994

By A. Singh

Two alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho have been processed by direct extrusion at 300°C and 200/230°C to produce various microstructures containing icosahedral quasicrystalline phase with different grain sizes. The alloys were mechanically tested in tension and compression. The mechanical properties were related to the grain size and microstructures studied by transmission electron microscopy. The extruded alloys showed a mixture of nano-sized icosahedral and monoclinic Mg4Zn7 phase, as well as icosahedral phase particles a few hundred nanometers in size distributed in the matrix. Coarse icosahedral phase particles several micron in size also remained after extrusion. The alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho extruded at the same temperature of 300°C produced very different grain sizes of 15 and 3 µm, respectively. The alloy Mg96.9Zn2.7Ho0.4 extruded at 200°C and Mg93Zn6Ho extruded at 230°C produced grain sizes of 0.7 µm and 1.5 µm, respectively. Both the alloys showed yield stresses of about 300 MPa in both tension and compression with elongations of about 18%. Hall-Petch parameters are calculated for the alloys.

Jan 1, 2006

By M. Saghaeian, R. Hejazi, Sheikhzadeh. V., A. Abazarpoor

"The morphology of iron ore concentrate particles is known to influence several properties of iron ore pellets, including drop number, compression strength, and reduction properties. This study aimed to determine why grinding methods and particle morphology influence green pellet properties. Particle morphology can be directly related to the grinding method: ball mill (BM) or high pressure grinding roll (HPGR). In this research, two iron ore concentrates, namely Gol-e-gohar and Ardakan, were ground by a BM and HPGR to produce a suitable Blaine value for pelletizing (nearly 1,900 cm2/g). Morphological features of particles were subsequently investigated by sieving and cyclone sizing for particle size distribution, the Brunauer-Emmett-Teller (BET) and Blaine methods for specific surface area (SSA) and scanning electron microscopy (SEM) for the evaluation of shape descriptors. It was concluded that HPGR resulted in generating a greater proportion of fine particles compared to ball milling. The BET results showed that the SSA of HPGR pellet feed was higher than that from the BM due to a greater proportion of cracks, indents and bulges and the creation of new fracture surfaces. SEM images processed by ImageJ software indicated that particles ground by the BM tended to be more rounded and less elongated than HPGR particles because of the breakage model of each method. To show the effect of morphology on the green pellet quality, green pelletizing was performed in a pilot pelletizing disc. The HPGR pellet feed had a higher drop number in comparison to the BM pellet feed, due to the angular and rough shape of the particles.INTRODUCTIONThe demand for fine or ultra-fine particles as feed material for ceramics, composite materials, and mineral processing is on the rise (Kotake, Kuboki, Kiya, & Kanda, 2011). The final concentrate of iron ore processing plants (filter cake) has a size range roughly between 0 and 300 µm, depending on the liberation of Fe containing particles (Meyer, 1980). In general, to produce a suitable pellet feed of appropriate quality, Blaine numbers of 1800–2000 cm2/g should be achieved (Van der meer, 2015)."

Jan 1, 2016

By Colin P. Skidmore

Long touted as Australia?s fourth uranium mine the sediment-hosted Honeymoon Uranium Project is close to commercial production using insitu-leach mining methods. Uranium mineralisation occurs as pitchblende coatings on unconsolidated quartz sand and gravels within a stacked aquifer system in a buried palaeochannel located in the Curnamona Region of South Australia. A final NI43-101 Feasibility Study is close to completion which has included extensive delineation drilling using PFN technology to accurately measure uranium grade and distribution. This data integrated with a detailed 3D sedimentalogical model is being used to optimise wellfield and plant design.

May 1, 2006

By Dharmendr Kumar, Pradip, Beena Rai, Venugopal Tammishetti

"Due to rapid depletion of high grade Indian iron ores, there is a need to utilize low grade fines and slimes. However, these fines and slimes, in their current form, cannot be utilized in steel making due to their high alumina (6-10%) contents. Several beneficiation strategies such as gravity separation, magnetic separation, flotation and selective flocculation are currently being explored for the upgradation of low grade fines and slimes. In our previous work density functional theory simulations were employed to come up with selective flocculants for beneficiation of iron ore slimes. Our simulation results suggested that starch and guar gum are more selective towards iron minerals than other minerals present in the sample. Grinding of iron ore fines becomes necessary in some cases to achieve adequate liberation for removing alumina impurities in Indian iron ores. We have thus investigated effect of grinding of iron ore fines on its selective flocculation-separation.In the present work, we have taken natural iron ore fines from one of the Indian iron ore mines and ground it to -400 mesh (<37 microns) in dry and wet conditions. X-ray diffraction study confirmed the presence of minerals hematite, goethite, gibbsite and kaolinite in the sample. The fine ground samples were used in selective dispersion-flocculation study with corn starch and guar gum flocculants. It is interesting to note that even though the dry and wet ground samples possess almost similar particle size distributions, significant differences were observed in yield and grades of the concentrates thus produced. These differences may be arising due to the coating of alumina containing minerals on iron minerals. We have also studied the effect of addition of dispersant while grinding. Our study suggests that grinding conditions determine the efficiency of the separation process."

Jan 1, 2016

By A. Haque

"This paper describes an improved formulation of an analytical shear strength model developed by Haque & Kodikara (2012) by incorporating the failure of regular concrete/rock joints subjected to CNS condition. Sokolovskii’s analytical solutions developed for failure stress of slopes have been found to be effective in this regard. The analytical models have been validated for predicting the shear behaviour of concrete/rock joints subjected to various CNS loading conditions. The model has been found to accurately predict the dilation, normal stress and shear stress behaviour for a regular triangular saw-tooth joint up to the peak shear stress. Moreover, the peak shear stresses of concrete-rock joints with asperity angles ranging from 5 to 27.5o compared reasonably well with the available laboratory test results.INTRODUCTIONA new shear strength model for elastic regular triangular concrete/rock joints loaded under Constant Normal Stiffness (CNS) boundary condition has been developed by Haque & Kodikara (2012). The salient feature of this model is its capability of accurately estimating the normal and shear stresses of joints with shear displacements under CNS condition by incorporating the elastic deformation of asperities. However, the shear strength model of Haque & Kodikara (2012) for the elastic asperities cannot be directly employed to predict the peak shear stress of a joint experiencing plasticity under applied loads. Therefore, the model inevitability requires articulation of an appropriate shear failure criterion simulating the boundary conditions of the loaded asperity to predict the peak shear stress and corresponding normal stress and dilation behaviour of concrete/rock joints. Sokolovskii (1960) developed a set of analytical solutions for failure stress of slopes comprising c-??soils, which can be exploited effectively to simulate the failure condition as encountered for loaded regular triangular concrete/rock joints (Seidel & Haberfield, 2002)."

Jan 1, 2015

By D. Mraz

"Under high pressure in a deep potash mine, the salt rock behaves in accordance with the concept of a generalized, perfectly plastic substance. The paper presents the evidence of this behaviour and engineering concepts f or room-and-pillar design. IntroductionThe mining and refining facilities at International Minerals &. Chemical Corporation (Canada) Limited are located near Esterhaz y at the southeastern edge of the Saskatchewan evaporites. Ore extraction began in 1962 and at the present time the annual mining capacity is in excess of eleven million tons of potash ore.A generalized geological section is shown in Figure I. The mining horizon is overlay in by 100 feet of rock salt followed by a thin bed of competent dry shale. The strata in the next 1,500 feet are generally competent and locally water bearing. The Blairmore formation contains strata of water-bearing unconsolidated sand. Below the mining horizon, rock salt is interbedded with anhydrite bands.The 8-foot mining bed is distinguished mainly by grade and clay content, as there is no definite bed boundary. The chief mineral s are halite, sylvite and, in some cases, carnallite, with up to 2 per cent disseminated clay. The ore is coarse grained, with crystals averaging one-half to three-quarters inch across.The major mining problem is related to the fact that the Dawson Bay formation, overlying the evaporites, contains areas and channels that are highly porous and permeable and are filled with unsaturated brine under high pressure. Consequently, all mining areas, with no exception, must be so designed that the overburden salt stratum remain s competently supported for the duration of the mine .This paper outlines a successful engineering method of determining the stability of the pillar s and designing a stable room -and-pillar mining system."

Jan 1, 1980

By Carmen Mihaela Neculita

Sulfate-reducing passive bioreactors efficiently treat acid mine drainage (AMD) by increasing its pH and alkalinity and by removing metals as sulfide precipitates, in addition to hydroxides and carbonates. However, the new mining legislation sets discharge limits based on physicochemical parameters and on the non-toxicity of treated effluent as well. In this study, toxicity was assessed for effluent from 3.5 L column bioreactors filled with mixtures of natural organic carbon sources and operated at two different hydraulic retention times (HRTs) of 7.3 d and 10 d for the treatment of a highly contaminated AMD. Acute toxicity was observed for D. magna, and a toxicity identification evaluation (TIE) procedure was performed to identify potential toxicants. To help the interpretation of the toxicity results, metal partition in the effluent was also determined by filtration and ultrafiltration, while geochemical modeling was performed for metal speciation evaluation. The 10 d HRT effluent was nonacutely lethal for rainbow trout but acutely lethal for D. magna, whereas the 7.3 d HRT effluent was toxic for both organisms. The toxicity to D. magna was eliminated by 2 h of aeration for the 10 d HRT effluent, and the TIE procedure suggested iron as a cause of toxicity. However, the 2 h aeration eliminated the toxicity of the 7.3 d HRT effluent, only if performed after the pH rising to 9.3. Data regarding metal speciation indicated instability of both effluents during aeration and were consistent with the toxicity being caused by iron. The study indicates that design of passive treatment should include sufficient HRT and posttreatment aeration to meet acute toxicity requirements. Keywords: acid mine drainage, sulphate-reducing passive bioreactors, hydraulic retention time, effluent toxicity, metal speciation

Nov 1, 2008

By P. J. Deveaux, M. J. Kreczmer

The Tartan Lake deposit 12 km northeast of Flin Flon, Manitoba, was discovered in March of 1984 during the investigation of a VLF anomaly. The discovery hole intersected 16.83 metres averaging 21 gm Au/tonne. Since then, 99 holes, over 21,000 metres, have been drilled outlining 419,491 tonnes grading 11.79 gm Au/tonne in a di stinct group of mineralized lenses referred to as the Main Zone. Three other mineralized zones are known on the property but no reserves have been allowed for these, the South , East and Base Line zones. The Main Zone consists of seven parallel, east-west striking, quartz lenses. The lenses dip steeply to the north and plunge steeply west to northwest. Lens number l strikes for 160m and extends vertically to the 90m level. Within th is lens there is a 60m interval of low grade materi al. Lens number 2 is located about 5-l0m within the foo twall of Lens number I. Near surface this lens stri kes for 40m, at 200m level the strike length increases to 200 m. To date the deepest mineralization on Lens 2 has been intersected at a vert ical depth of 527m. Five smaller lenses are located in the foo twall of Lens 2 , containing gold va lues similar to the two main lenses but erratically distributed. The South Zone, located 100m south of the Main Zone, strikes east-west fo r l00m above the 100m level. The East Zone, found 230m east of the Main Zone, strikes fo r 80m and may possibly be an ex tension of the South Zone. The Base Line Zone is located 275m south of the Main Zone. Sporadic, but very significant gold intersections have been obta ined1n all three zones. Gold-bearing quartz-ca rbonate tourmaline veins are generally confined to a silicous crystal tu ff hori zon. The crystal tuff exhi bits fi ve distinct types of alteration: silicification, sericitization, ca rbonati zation, chlorit ization and pyritization. Silicification has resulted in a perasive addition of silica and the generation of multiple quartz veins. Sericiti zation is restricted to the crystal tuff. All rock units are pervasively carbonatized . Ankerite is abundant in the quartz veins and within the shear zones, particul arly those located along the chilled margin of a nearby gabbro-diorite intrusion. Chloritization is widely spread th roughout the rock units, while pyritization fo rms a broad alteration halo associated with the orebody. Sulphide accesso ry minerals associated with the gold , whi ch fo r the most part appears to be free, are chalcopyrite and pyrite. Generally, the higher grade gold values are related to an increased content of sulphides in the qua rtz veins. The average sulphide content in the deposit is less than 5 %.

Jan 1, 1986

By A. Pearson, F. A. Auld, S. O. Colbeck

"""The theory of buckling of shafts and Steel tunnel-linings"" was published by E. Amstutz in 1970 and commented on by S. Jacobsen in 1974. The authors have revised and enhanced Amstutz’s work to address Jacobsen's comments on its limitations and to extend its validity over a wider range of pipe/shaft geometries, including those commonly found in deep mine access shafts. The author has looked at Amstutz’s assessment of strengthening with flexible shear anchorages and adapted the theory of non-linear shear deformation response of bolts to develop a method of assessing increased buckling capacity utilising the full plastic shear capacity of studs. INTRODUCTION “Amstutz Buckling” refers to the buckling of pipe embedded in concrete under external uniform pressure. In terms of a mining environment, this relates directly to the design of a watertight shaft. This load case will commonly occur where a main shaft is cast against a geostatically stable primary liner and the only load applied to the final shaft is that of a uniform ground water load. Ernst Amstutz wrote his first paper on buckling of pressure-shaft steel linings in 1950 and subsequently improved his theory (Amstutz, 1970), which was then widely adopted for use within the industry. Years later, an alternative approach (Jacobsen, 1974) was proposed. Within his paper Jacobsen critiques Amstutz work, identifying some mathematical inconsistencies and highlighting limitations of the theory imposed by approximations adopted by Amstutz. Despite these limitations Amstutz work has still been used as the favoured design theory for use in the mining industry. In reviewing this body of work the author realised that with the advent of readily available computing software it was possible to adopt an iterative approach using Amstutz approximate formulae to find a solution to the original precise formulae, thus eliminating the limitations highlighted by Jacobsen The shear deformation to load characteristics of bolts has long been established (Crawford & Kulak 1968) and used for the plastic design of bolted connections in shear. This relationship is directly transferable to the design of shear studs, typical properties are well known, and actual values easily established in simple lab tests. The author has taken this relationship and modified Amstutz theory (Amstutz, 1970) for shear anchored strengthened liner buckling, to give a more efficient solution, using readily available material properties."

Jan 1, 2019

By John S. Stevenson

Zeballos mining camp is on the west coast of Vancouver island; 195 nautical miles northwest from Victoria.; The spectacularly rich gold-bearing veins that made Zeballos an important; gold camp were found early in 1934. Small pockets of very coarse; gold had been found earlier under large boulders at the mouth of Spud; creek; and in the autumn of 1933 rich gold-quartz float was found near the; mouth of the creek. The rocky beds of the steep creeks entering Spud creek; were searched for its source and as a result the veins on the White Star property; were found. The Goldfield vein on the Spud Valley property was discovered; in 1935; and the No. 1 vein on the Privateer in 1936. In the general; prospecting activity that quickly followed; other veins were found; not; only in Spud creek but in other creeks draining into Zeballos river.

Jan 1, 1954

By G. R. Davidge

"Falconbridge Mine has a history of significant microseismic activity dating back to 1955. Since mid-1981, a microseismic monitoring system has been operating in the area around the No .9 Shaft hoist room located 25 m from the are zone at a depth of 1200m. Several mine wide faults dissect this area and have been shown to be microseismic-active due to mining. The microseismic monitor has been interfaced with a small dedicated personal computer and a communications device to perform routine data evaluation and to produce graphical output. The programs are described and selected result s from the monitoring program are presented.IntroductionFalconbridge Mine is located on the southeast rim of the Sudbury Basin. The nickel-copper sulphide ore zone is essentially a tabular orebody striking approximately east-west and dipping at 80 degrees north near surface and rolling to 75 degrees to 80 degree s south by the 1000 level. (Mine level number s represent the approximate depth in feet below ground surface .) This dip is maintained down to the 6000 level. The north wall is comprised of jointed norite and a faulted contact up to 1 m thick exists between the ore zone and the norite. The south wall rock is a greenstone with highly siliceous lenses and often has a faulted contact with the ore zone. No less than five mine wide faults exist, as shown in Fig. I.Mining ha s been carried out from virtually the bedrock contact to depths of 1830 m although the majority of current activity is between 900 and 1500 m below surface. A winze provides access below the 4025 level and the cage hoist room is located on the 3850 level in the north wall 25 m from the contact. Because of concern for the stability of this hoist room, there has been no mining activity within 60 m of the hoist room and by 1980 this block of ore was one of the major blocks of high-grade ore remaining in the mine . Mining of this block was originally scheduled for very late in the decade.Prior to a six-month shutdown in 1982, this mine produced approximately 450,000 tonnes of ore annually, mainly by cut and- fill techniques. Following the shutdown, annual production has been reduced to approximately 200,000 tonnes and production is now mainly by undercut and fill techniques .Mining-induced seismicity has occurred at Falconbridge Mine since at least 1955 and reviews of the microseismic problems for the periods from 1965 - 1970 and from 1971 to 1979 were made by Singh (1971) and Vongpaisal et al. (1980), respectively. The need for instrumentation was addressed by these authors. Following several large events during the spring of 1980, a decision was made to investigate existing microseismic monitors and to apply micro seismic monitoring techniques in Falconbridge Mine. Application of microseismic monitoring to Falconbridge Mine was to concentrate on the No . 9 Shaft hoist room area of the mine, particularly around the 4025 level where a large mechanized cut-and- fill stope was approaching this level. By mid - 1981, the microseismic monitor was fully installed and with in a year , a short-period seismograph and a personal computer had been added to the system."

Jan 1, 1984

By D. S. Robertson, G. E. Nutter, T. P. Podolsky

"IntroductionBasal Proterozoic quartz-pebble conglomerates are found both west of Elliot Lake, in Duncan, Jarvis and Aweres Townships, north of Sault Ste. Marie and to the east and northeast of Sudbury, Ontario. Locally, while well packed and pyrite-rich, they carry little to no uranium. Locally, they carry gold. These features generally are ascribed to variations in the source areas of the rocks.In two other areas of Canada, similar basal Proterozoic units contain quartz-pebble conglomerate beds with uranium.Sakami LakeLocation and HistoryThe Sakarni Lake uranium deposit is found in a narrow, northeast-trending, Archean greenstone belt located 95 miles southeast of Fort George, on James Bay, and 240 miles north of Matagami, Quebec (Fig. 1).The deposit was detected by Inco in 1971, during an airborne EM survey which carried a newly developed Inco spectrometer system flown at 450 feet. Ground investigation, in 1972, resulted in the discovery and sampling of quartz-pebble conglomerate which yielded assays as high as 0.19% U3O8.Extensive field exploration was conducted between 1972 and 1975. Sixty-five diamond drill holes, to a total of 13,969 metres, served to define the extent and economic potential of the conglomerates which extend over a total strike length of about eight kilometres."

Jan 1, 1986

By T. Bhambhani, O. Yavuzkan, D. R. Nagaraj

"Cu ore bodies commonly contain oxide Cu at the surface, with sulfide Cu content increasing with depth. The recovery of oxide Cu minerals by flotation is a longstanding challenge in the minerals industry, especially for high acid-consuming ores which would not be economical for direct acid leaching. Current practice of oxide Cu recovery involves sulfidization (often using controlled potential sulfidization or CPS) using NaSH (or Na2S) followed by flotation using traditional sulfide collectors. CPS has shown to improve recovery of oxide Cu but has the following limitations: a) HSE issues with NaSH, b) high consumption of NaSH, and c) inability to recover certain oxide Cu minerals because they are refractory to sulfidization. The oxide Cu flotation is further complicated by the presence of certain non-sulfide gangue minerals which adversely impact both recovery and selectivity.Over the past eight decades, numerous collectors have been proposed and evaluated for the direct flotation (i.e. without sulfidization) of oxide Cu minerals, the most researched of which is alkyl hydroxamate. While there are numerous publications dealing with the fundamentals of interaction of alkyl hydroxamates with single minerals, there are few publications which discuss the practical aspects of alkyl hydroxamate use in ore flotation, particularly their use with sulfidizing agents. Case studies in this paper include methods to identify optimum combinations of sulfidizing agents and oxide collectors to maximize recovery for various types of ores. It was observed that some ores do not require any sulfidization, while others require at least partial sulfidization to improve efficacy of AHX. Depending upon the ore type and mineralogy, recovery improvement in the range of 5 to 15% units, over and above that achieved with CPS, has been observed with the use of AHX. For ores requiring high dosages of NaSH, it was shown that AHX can be used to reduce the NaSH consumption significantly. The challenges associated with the presence of non-sulfide gangue minerals in oxide copper ores are included, and the use of modifiers to alleviate the associated problems and enhance the performance of AHX is discussed."

Jan 1, 2016

By Anna Szostak-Chrzanowski, Adam Chrzanowski

"New techniques in monitoring surveys and new methods in the analysis and prediction of ground subsidence are being developed in the Department of Surveying Engineering at the University of New Brunswick (UNB). The new surveying techniques include a telemetry monitoring system developed at UNB in cooperation with CANMET, and use of the satellite Global Positioning System. A generalized approach to the analysis of deformation surveys has been developed which permits an integrated analysis of geodetic and geotechnical measurements in geometrical modelling of ground subsidence. A computer program, FEMMA, has been developed for the elastic and non-linear elastic analysis and the deterministic prediction of deformations using the finite element method.IntroductionResearch and development of new monitoring techniques and new methods in the analysis and prediction of ground subsidence in mining areas is an integral part of a broad research program on deformation surveys which is being carried out in the Department of Surveying Engineering at the University of New Brunswick.The research concentrates on:developmentof a general method for predicting deformations with an emphasis on the use of the non-linear elastic finite element analysis; development of a generalized approach to the geometrical analysis of deformation surveys with an integration of geodetic and geotechnical measurements; and development of new monitoring techniques with an emphasis on continuous data acquisition and application of new space techniques such as the satellite Global Positioning System (GPS).This paper gives a brief report on the progress and recent developments within the above program."

Jan 1, 1987

By S. Kawai

Natural convective flow of the electrolyte solution plays an important role in several electrochemical systems. Copper refining electrolysis is the most important industrial process to produce high purity copper on large scale. Turbulent natural convection develops along vertical plane copper electrodes installed in an unstirred electrolyte accompanying with the electrochemical deposition and dissolution of copper during the electrolysis. It introduces the electrolyte stratification phenomenon. Thus, the electrolyte is circulated in a special way depending on each electrorefining tankhouse. The theoretical discussion is indispensable to understand the coupling phenomenon between the ionic mass transfer rate and the morphological variations of electrodeposited copper. In present study, the mass transfer rate of both Cu2+ and H+ ions as well as the momentum transfer rate is numerically analyzed accompanying with the turbulent natural convection along 1 m high Cu metal electrode surface.

Jan 1, 2007

By Y. Hou, E. Arinaitwe, L. Tong

A series of dense medium separation (DMS) tests were performed on four low-grade copper ores from Mount Polley mine in order to determine their amenability to pre-concentration. The tested ores contained disseminated sulphides, mostly chalcopyrite with low copper grades (0.15% - 0.2%) and relatively high iron grades (4.76% - 5.63%). The samples were screened into different size fractions ranging from 9.5 mm to 50.8 mm and DMS tests were performed on each size fraction at various separation densities. The pre-concentration efficiency at different size fractions and separation densities was evaluated in terms of metal upgrading and distribution. Mineralogical tests were also performed on selected DMS sink and float samples in order to understand the influence of mineralogy on the pre-concentration efficiency. The results showed that significant copper upgrading was achieved for intermediate size fractions only at the highest separation density tested. The copper recoveries generally increased with particle size at all separation densities. However, it was impossible to upgrade the copper content in the ores and achieve acceptable recoveries and mass rejections at the same time. Copper recoveries and grades showed a strong correlation with iron recoveries and grades indicating that it is possible to pre-concentrate copper by recovering magnetite and other iron-containing minerals in the ore. Overall, the results suggest that the optimum separation density and pre-concentration efficiency is a function of particle size, and that the ore mineralization properties limit the performance of DMS as a pre-concentration technology for such low-grade disseminated ores.

Jan 1, 2014