Search Documents

By Norman A. Parlee

Introduction The principal primary iron and steel producing capacity of the Dominion Steel and Coal Corporation is at the Dominion Iron and Steel, Limited, plant at Sydney, Cape Breton Island, Nova Scotia. The main raw materials are Cape Breton coal, Wabana (Newfoundland) iron ore, and Port-au-Port (Newfoundland) limestone. This plant, which was established at the turn of the century has gradually expanded its production facilities so that today its ingot producing capacity is over 720,000 tons annually. Principal operating units of the plant at present are three batteries of 173 Koppers by-product coke ovens with conventional by-product recovery equipment, three blast furnaces .of 15 ft. 6 in., 18 ft. 3 in., and 19 ft. 3 in. hearth diameter (inside the brick), one 700-ton hot metal mixer, ten open hearth furnaces (two of 175-ton capacity, three 12 5-ton, five 60-ton), one 10-ton electric furnace, a 40-inch blooming mill, a billet mill, a rail mill, a tie plate mill, rod and bar mills, and a wire and nail mill. Extensive machine shops and an iron and brass foundry are also available for plant maintenance and repairs. This paper will describe developments during the past five years and those now in process. It will also briefly discuss research being done and indicate the direction of future development.

Jan 1, 1951

Despite the fact that mined minerals and gemstones have allowed human beings to continuously improve their standard of living throughout the ages, mining has also been implicated in violent conflict for two principle reasons. The first is that mineral resources have been used or traded to conduct or finance violent conflict from small to large scales. The second is the substantial social, economic and environmental changes that occur in a community or a region as a result of mining activity which can either precipitate or re-awaken latent conflict. A modern complication of mining-related violent conflict is the trend for activists, international NGOs and intergovernmental organisations (e.g. the United Nations) to regard any human consequences of resource extraction in terms of Human Rights violations. Acknowledging but not labouring the Human Rights implications of mining-related violent conflict, this paper explores whether or not there is a relationship between the actual or perceived value of mineral resources and the level of violence that occurs in mining-related conflicts. Key to the investigation is a mapping exercise of mining related conflict from 2005 ? 2012: to see where mining related conflict is happening; to identify precipitant causes of mining related conflict; and, to discover what correlation ? if any ? there might be in the degree of violence and the value of the mineral(s) implicated. Findings of the analysis are presented in this conference paper.

Aug 1, 2013

By G. A. Sutton

"At the San Manuel mine (Arizona, USA), in-situ copper leaching of a copper porphyry deposit was carried out from 1986 to 1999 during underground and open-pit mining. In 1993–1994, well¬field testing of the supergene zone, composed primarily of chrysocolla and copper-rich clay minerals, led to estimates that 52% of the acid-soluble copper (ASCu) could be recovered during in-situ leaching; however, the actual recovery from zone 6, which had the longest leach history, was approximately 42%. Comparing drillcore assay data from holes drilled before and after leaching also indicated an approximate recovery of 42%. The discrepancy between the predicted (52%) and actual (42%) recovery is probably related to several factors, including difficulty maintaining fluid saturation, channelling effects, and gypsum precipitation. ¦ KEYWORDS Copper oxides, in-situ leaching, Modelling, Porphyry, Solvent extraction and electrowinning (SXEW), Well-to-well RÉSUMÉ À la mine San Manuel (Arizona, États-Unis), on a procédé de 1986 à 1999 à la lixiviation in-situ de cuivre d’un gisement porphyre cuprifère pendant l’exploitation minière souterraine et à ciel ouvert. En 1993 et 1994, des essais effectués dans des champs de captage de la zone supergène, composée principalement de chrysocolle et de minéraux argileux cuprifères, ont abouti à des estimations selon lesquelles on peut récupérer 52 % de cuivre soluble dans l’acide (ASCu) pendant la lixiviation in-situ ; toutefois, la récupération réelle dans la zone 6, qui affiche l’histoire la plus ancienne en matière de lixiviation, était d’environ 42 %. La comparaison des données d’analyses de forage obtenues à partir de trous forés avant et après la lixiviation indiquait également une récupération approximative de 42 %. La différence entre la récupération prévue (52 %) et réelle (42 %) réside probablement dans plusieurs facteurs, notamment la difficulté à maintenir la saturation des fluides, les effets de canalisation et la précipitation du gypse. ¦ MOTS CLÉS d’un puits à l’autre, extraction par solvant et extraction électrolytique (SXEW), lixiviation in-situ, modélisation, oxydes de cuivre, porphyreINTRODUCTION in-situ copper leaching at the San Manuel mine, Arizona, USA (Figure 1), began in 1986. It was recognized that some of the copper oxide resource was not economically recoverable by conventional open-pit and heap leach methods using solvent extraction and electrowinning (SXEW) and a high stripping ratio would be required to access part of the resource. At the time, in-situ leaching was becoming popular in the uranium industry, but the approach was virtually unknown in the copper industry, especially at a large scale."

Jan 1, 2019

By R. G. K. Morrison

By arrangement between the Ontario Mining Association and Messrs. John Taylor & Sons, Mining Engineers, 6 Queen Street Place, London, E.C.4, the writer was engaged for a period of not more than three months to report on the rockburst situation in Ontario mines. This was later amplified, by mutual agreement, to include, at the expense of detail, visits to the larger camps where rockbursts had not occurred, to get a general picture of conditions and to discuss the subject with operators in their respective areas. Scope of Activities Visits were paid to the following properties for the purpose of enquiry and discussion; the underground workings of those mines marked with an asterisk were visited on one or more occasions: KIRKLAND LAKE * Macassa Mines, Limited * Kirkland Lake Gold Mining Co., Ltd. * Teck-Hughes Gold Mines, Limited * Lake Shore Mines, Limited * Wright-Hargreaves Mines, Limited Sylvanite Gold Mines, Limited Toburn Gold Mines, Limited EAST KIRKLAND & LARDER LAKE Upper Canada Mines, Limited Chesterville Larder Lake Gold Mtng Co., Ltd. Kerr-Addison Gold Mines, Limited Omega Gold Mines, Limited PORCUPINE * Hollinger Consolidated Gold Mines, Ltd. * Mcintyre Porcupine Mines, Limited * Dome Mines, Limited * Buffalo Ankerite Gold Mines, Limited Paymaster Consolidated Mines, Limited Preston East Dome Mines, Limited Pamour Porcupine Mines, Limited Broulan Porcupine Mines, Limited Hallnor Mines, Limited Naybob Gold Mines, Limited Delnite Mines, Limited Moneta Porcupine Mines, Limited DeSantis Porcupine Mines, Limited Coniaurum Mines, Limited SUDURY lnternational Nickel Co. of Can., Ltd. * Falconbridge Nickel Mines, Limited LITTLE LONG LAC AREA * Little Long Lac Gold Mines, Limited MacLeod-Cockshutt Gold Mines, Ltd. Hard Rock Gold Mines, Limited Bankfield Consolidated Mines, Limited Magnet Consolidated Mines (1936), Ltd. à PICKLE LAKE AREA * Central Patricia Gold Mines, Limited * Pickle Crow Gold Mines, Limited UCHI LAKE * Uchi Gold Mines, Limited McKENZIE ISLAND AREA Gold Eagle Gold Mines, Limited * McKenzie Red Lake Gold Mines, Ltd. * Cochenour Willans Gold Mines, Limited RED LAKE * Howey Gold Mines, Limited Hasaga Gold Mines, Limited Madson Red Lake Gold Mines, Limited

Jan 1, 1942

By G. C. Mackenzie

At the last Annual Meeting of the Institute, Dr. C. V. Corless sketched the potential mineral wealth of Canada so clearly, graphically and with-all so entertainingly that one's imagination was fired with the promise held out to future generations for the tremendous expansion of the mining industry in the Dominion. Posterity will undoubtedly witness the fruit of much of the geographical search and survey that is now carried on by our government mining departments. Year after year the work advances, slowly but surely, new areas are . explored, older areas are surveyed in detail, the information being compiled in maps and reports of incalculable value to the prospector, the engineer and the general public. The immensity of the task of exploring, geologically, the outlying portions of the country, with the ultimate view of making valuable mineral discoveries, may be visualized from a study of Dr. Corless' paper and the subsequent discussion which took place and one becomes impressed with the fact that three-quarters or more of the problem can be included under the word "transportation". For instance Dr. Corless said, "The few geological explorers who have penetrated to these remoter regions . . . . . . have as a rule been compelled to stick closely to canoe routes,"; Dr. Goodwin remarked, "This barren Laurentian granite, which is put down on the maps as covering the greater part of this area, is the best guess the geologist could make from travelling along watercourses Within the next few years . . . . . . the Timiskaming and Northern Ontario railway will undoubtedly be extended to James Bay . . . . . . In order that we may be prepared for the probable influx of prospectors when transportation facilities to tidewater are provided, I think all available information on this district should be gathered together in handy form." All three-Corless, Goodwin and Cole-emphasize the well-known fact that explorers, geologists and prospectors working in new country must stick to the watercourses and that transportation by rail, road or water has always been the all-important deciding factor in facilitating the exploration and development of remote districts. Dr. Corless did, however, suggest other means of transportation in stating, "The aeroplane will be of assistance in future study of some parts of these remote areas."

Jan 1, 1924

By M. J. Marinigh

Increased safety requirements, higher operational costs, greater environmental restrictions, and new competitive processing techniques are the challenges smelter operators must confront in order to remain economically viable. In converting furnaces which have tuyeres such as the Noranda Reactor and the Teniente, Peirce Smith and Hoboken converters, efficient tuyere line management is critical to optimizing blowing rates, increasing refractory life, and improving safety. This paper will describe recent improvements made to equipment used for tuyere punching, tuyere silencing, tuyere pyrometry and refractory drilling of tuyeres and how the proper application of the equipment can lead to operational and safety improvements.

Jan 1, 2007

By J. P. Caulfield

THE Hudson Bay Mining and Smelting Company's underground mine at Flin Flon, Manitoba, has in the past been serviced by two working shafts-the North Main shaft, and the No. 3 shaft. The North Main shaft is used to hoist the total production from under-ground, and handles the greater part of the mine supplies and crews. The shaft is five-compartment design, rectangular in cross-section, and is equipped entirely with steel shaft sets from the surface to the finished depth of 2,210 feet. Hoisting equipment in the surface plant will not permit the North Main shaft to be extended below its present finished depth. The No. 3 shaft, located approximately 2,300 feet from the North Main shaft, is used primarily as a ventilation shaft, and for hoisting lower-level development waste to the 390 level, where this material is used as mine fill. The No. 3 shaft is of standard rectangular design, timbered with 8-in. by 8-in. creosoted fir sets, hung on 6-foot centres. From the surface to the 1,430 level, the No. 3 shaft consists of three 5 ft. by 5 ft. compartments, and below this level to the completed depth of 2,300 feet, the shaft is increased to four compartments. To service the mine and to expedite development below the 2,210 level, a one and one-half compartment winze was sunk from the 2,210 level to a depth of 766 feet, or approxima tel y the 3,000 level.

Jan 1, 1941

By G. M. Behrend

"AbstractMeasurement and control systems in minerals processing plants are usually well thought out and designed. The criteria and design parameters have been interpreted correctly.However, these systems often fail to perform satisfactorily or break down altogether as a result of in-plant conditions which are unpredictable and over which the instrument systems designer has no direct control. The foresight necessary to anticipate the problems and allow for them in the systems design can only be generated by experience.This paper lists the most common of these problems and offers practical methods for their solution. It then follows with an analysis of instrument installation practices and comments on special points that need watching.Finally, instrument maintenance is discussed with a view to achieving good maintenance at the best possible economy.Good MeasurementGeneralTHE MINES and mineral processing plants of the nineteen seventies, after decades of sensible caution, have now committed themselves to extensive automatic control. X-ray analyzers are freely specified. Sample acquisition systems are efficient and automated, computers are reliable and relatively cheap, and computer control systems in conjunction with the new analyzers are operating in a good many plants and are proving to be profitable.The sight of shift foremen and floor operators assembled in front of a TV-tube and taking a computer data display as gospel truth is quite common now, and yet was quite unthinkable only ten years ago."

Jan 1, 1977

By L H. Warren

The types of equipment available for generating a plasma have been reviewed. The efficiency and potential of the plasma generating equipment used in performing extractive metallurgical reactions have been determined. A general classification of the reactions that might be per-formed in a plasma has been proposed. Experimental work done on extractive metallurgical plasma reactions, heat transfer between the plasma and solids, and the quench of the products of plasma reaction has been summarized. From the preliminary results it appears that the high-intensity are or the transpiration-cooled anode plasma torch offer the most promising areas for further research. C ONSIDERABLE world-wide research effort is currently being devoted to the development of processing technologies which employ the new high-temperature generating devices that have appeared over the past few years. The plasma flames produced by these devices offer the potential for subjecting materials to any single gas or mixture of gases at temperatures up to 20,000°K. With these conditions available, many reactions in extractive metallurgy,

Jan 1, 1965

By Philip J. Bangerter, Chris Twigge-Molecey

Design for safety is critical to metallurgical plants, due to the inherently dangerous nature of their processes. Two significant areas of concern are: 1. preventing catastrophic process failures that cause damage or injury; and 2. operational safety that directly affects those working in or living near the plant. Process safety involves human behaviour, but the designer can eliminate or control hazards by engineering approaches, and control impacts through the design of the operating procedures. The tools available to guide safe facility design include bowtie analysis, hazard analysis, and hazard and operability studies. Clean plant design principles can guide the design process to address in-plant occupational health and safety issues. Auditing and review is a key part of the overall design process.

Jan 1, 2015

By S. Klingmann

ABSTRACT In this paper, we used data collected from the Gibraltar mine to analyze the effect of the TyreSense tire monitoring system on tire performance by reducing tire wear and preventing premature tire failure or damage. We analyzed the relationship between tire temperature, tire pressure, and tire failure or damage to help better understand the importance of controlling high tire temperature and pressure. The results enhance and expand the knowledge of the management of tire operational pressure and temperature.

Jan 1, 2014

By V. L. Eardley-Wilmot

Diatomite as prepared for the market is a fluffy, white powder, remarkably light in weight-it weighs only 10 to 15 pounds per cubic foot, or one-tenth as much as sand. Being extremely porous and inert, it is in large and increasing demand for insulation and filtration purposes, as general filler, and for many other uses. Structure Structurally, diatomite is quite different from any other known commercial material. It is composed of myriads of microscopically small, siliceous shells of diatoms which belong to a group of flowerless aquatic plants called algae. When these plants die, the siliceous remains sink to the bottom of the water and form beds of diatomite. Over 8,000 species of diatoms are known, named, and tabulated. The intricate scroll-work and patterns on many of these are one of the marvels of nature, and yet so small are they that from 40 to 70 million separate diatoms may be contained in one cubic inch of material. However, the size and shape of these diatoms, which vary greatly (compare Figures 5 and 6), have an important bearing on the commercial use of the diatomite. The diatoms in the majority of the known deposits are so typical of that deposit that, after a micro-examination, an expert can usually tell not only from what part of the world, but also from what particular deposit, the sample has come.

Jan 1, 1931

By A. Zaidi

"The mining and metallurgy industry is highly energy intensive and one of the largest energy users in Canada. Energy costs are also a major component of total production costs in this industry as described in the 1990 Report of The Canadian Industry Program for Energy Conservation (CIPEC). For some plants, energy costs are reported to be up to 30% of total production costs. Therefore, a reduction in energy costs provides an opportunity to improve industry profitability. The specific energy intensity and production costs can be reduced by using modem energy efficient natural gas technologies. In addition, these technologies often improve product quality and increase productivity. Natural gas not only offers economic benefits, but is also environmentally benign as compared to other major energy sources. Emissions of NO"", CO2 particulates and SO2 are lower with natural gas than other fossil fuels.This paper provides a brief overview of some state-of-the-art gas technologies for the mining and metallurgy industry including cogeneration, oxy-air-fuel burners, ceramic immersion tube heaters, direct gas contact process, low NOx burners, and energy efficient liquid heating systems.CogenerationCogeneration is defined as the simultaneous production of electricity or mechanical power and useful process heat from a single fuel source. One of the primary considerations in selecting a cogeneration system is the relative quantities of electrical and thermal energy which are to be produced. Two types of systems are discussed below."

Jan 1, 1993

By P. C. Lighthall, D. W. Zandee, W. Shukin

"IntroductionThis chapter deals with the on land disposal and storage of fine tailing in slurry form behind dams. Other types of tailing, such as coarse dry cobbs from magnetic separation of iron ores and other dry materials, have special problems and are not addressed in this paper. The disposal of mine waste is not included, except as such materials may be of value in the construction activities related to tailing disposal.In earlier North American mining, mines were smaller and frequently disposed of their tailing by direct discharge into neighbouring streams or bodies of water. Where that was not practical or not permitted, the solids were collected in tailing ponds and only the effluent liquids were released or decanted. The dams used for these early impoundments were fragile structures and failures were common. With the advent of large, low-grade open pit mines, and increasing awareness of environmental and safety considerations, recently established mines have carefully-designed tailing disposal systems, with wellconstructed dams and attention given to protection of the environment. Older mines are being improved or at least being examined critically with a view to upgrading as necessary to meet the new standards.Modern tailing disposal systems are highly variable and unique to each mine. Tailing pond selection and design is dependent on available topography as also is the design of transport and water reclaim systems. Suitable sites that are at higher elevations than the mills or distant from them may require that the tailings be pumped. Dams, either earth or rock structures built of the most convenient and economic material, are usually a suitable mix of local borrow, mine waste and coarse tailings. The most economic structures are those built mostly of coarse tailing."

Jan 1, 1989

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTIONThe process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic.A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities."

Jan 1, 2012

By Milton Fies

Introduction The first experiment in underground gasification of coal in the United States was conducted at Gorgas, Walker county, Alabama, under a co-operative arrangement between the U.S. Bureau of Mines and the Alabama Power Company, at the suggestion of the Power Company. The test was conducted on property of the Alabama Power Company, that owns some 19,000 acres of coal-bearing lands on which there is developed a highly mechanized mine producing some 2,500 cons of good quality steam coal per day. At the same locality ?there is a 200,000 kilowatt steam plant one of the largest in the southern portion of the United States. The Alabama Power Company owes much of its beginning in 1912 to British vision and courage. The original plans for building hydroelectric plants in Alabama, and for the construction of necessary transmission lines, were submitted to Sperling & Company, bankers of London, who agreed to underwrite certain bond issues, the proceeds of which would be used in launching the new Company on its programme. The set-up by which these funds from England were received was through an intermediary Canadian company, which the English investors desired. The Canadian company - Alabama Traction, Light and Power Company, Ltd. became owner of the securities of the Alabama Power Company and marketed its own securities through the banking house of Sperling & Company. Without assistance at this time the Alabama Power Company could not have gone ahead with its programme of expansion and the bringing together of the properties necessary for laying the foundation for a strong Company, fortified with ample power resources essential for future requirements and for dependable service to the public.

Jan 1, 1948

By A. K. Ratte, C. M. Brown

"IntroductionIn autogenous mills, grinding of the ore feed is accomplished by the direct action of the variously sized rocks making up the feed on each other and the mill interior. Size reduction is achieved without the addition of grinding media foreign to the mill feed, differing in this respect from rod, ball, and pebble milling. The term ""semi-autogenous"" has entered common usage in the industry to describe autogenous mills to which supplementary grinding ball additions are made to increase the rate at which size reduction of the mill feed occurs, beyond that achieved solely by the action of rock on rock. In a semi-autogenous grinding (SAG) mill, 50Jo to 10% of the mill volume may be occupied by grinding balls, whereas a range of 25% to 45% is more usual in ball milling.The comminution of mineral ores using ""conventional"" techniques has been described in previous papers. In conventional operations, size reduction of mined ore, and liberation of the valuable mineral content, is typically accomplished using flowsheets employing two to four stages of crushing. Crushing is followed by one to three stages of grinding and classification using various combinations of rod, ball, and pebble mills. This paper describes operations employing autogenous or semiautogenous grinding as the principal stage in the comminution process. Primary crusher discharge, or in some instances run of mine ore, is fed directly to an autogenous or semi-autogenous grinding circuit. Final product sizing may be accomplished in a single grinding stage, the mills operating in closed circuit with classification equipment, or in several stages using autogenous and semi-autogenous mills for primary grinding, and ball or pebble mills for secondary grinding. In several operations a portion of the primary mill discharge is crushed in an intermediate comminution step, these circuits being called autogenousball- crusher circuits (ABC). Many different flowsheets exist, but common and important to most are crushed ore stockpiles, reclaim feeder and mill feed conveyor systems, pumps, screens, and classifiers. Autogenous grinding is employed in both wet and dry processes, although today wet predominate."

Jan 1, 1989

By Francis Gray

Mr. F. W. Gray: It is not my intention to read my paper as it is too long, so I will touch only on the high lights. The Sydney field is the most favourable example of undersea coal mining that exists, and I have not been able to find anything like it elsewhere. The nearest approach to it is a field in England where the Whitehaven collieries are operating, but it has a lot of faults. The net result of these faults so far met with in the seaward advance of the workings has been to increase, by something over 100 feet, the gain in depth of cover, in a distance of approximately three and three-quarter miles. In the Sydney field there are no faults of any consequence. On the east side, the English measures rise. In Australia the sea bottom fell and the cover became too light. On Vancouver Island the coal ran out, and in Japan the seams are steep and contorted. The Chilian fields resemble our own to some extent. An inundation of two collieries took place there some time ago, due, it is said, to the rise workings being allowed to approach the sea bottom too closely in the vicinity of a fault. The Cape Breton undersea field has been proved over a frontage of about thirty miles and has been attacked and penetrated for a considerable distance along that front. We have passed the prospecting stage and now generally use developed land areas as points of attack to win the undersea coal. Of our mining under the sea, it can be said that, with the exception of No. 1-B and Princess colliery, Sydney Mines, no real attempt has been made to win the undersea coal.

Jan 1, 1927

By The Mine Staff

THE PROPERTY of the Lamaque Mining Company, Limited, ?is located in the Town of Bourlamaque, seventy miles east of Noranda, in Bourlamaque township, Abitrbi county, north western Quebec. Gold production commenced at Lamaque in April, 1935, with an initial mill capacity of 250 tons per day. The capacity was doubled in November of the same year, and in December, 1937, it further increased to 1,200 tons per day. During the war years the mill operated at a reduced tonnage, but in 1951 milling units were added along with complementary crushing and shop facilities to bring the capacity to 1,500 tons per day. Finally, in 1953, the capacity was raised to 2,000 tons per day, which rate is being maintained at the present time. The total production at Lamaque from April 2nd, 1935, to December 31st, 1956, has been 9,168,901 tons of ore from which 2,208,168 ounces of gold was recovered. The total value of this production , excluding E.G. M.À.*, was $77,869,653.

Jan 1, 1957

By A. McLean, M. Barati

In this paper, examples are presented of pyrometallurgical research and associated teaching activities during the past century within the Department of Metallurgical Engineering, now the Department of Materials Science and Engineering, at the University of Toronto. Throughout these years, pyrometallurgical research has been characterized by recognition of the importance of the interdependence of measurements and models as well as the development and application of sensors, for the generation, validation and practical implementation of new knowledge. The important role played in the delivery of lectures and participation in joint research by Adjunct Professors with strong backgrounds in the pyrometallurgical industry is described. Projects conducted in close collaboration with the industrial sector and opportunities for students to obtain practical experience working as teams on a "round-the clock" shift basis within an industrial pilot plant environment are outlined. These activities, together with the involvement of students in poster competitions and the presentation of papers at society conferences and technical meetings, are still vital elements in the development of pyrometallurgists equipped with the appropriate professional skills for subsequent employment within academia, government laboratories or the industrial sector.

Jan 1, 2015