Search Documents

By R. Augsten, K. K. Feng, K. C. Cheng

"Methane emission and the desorption characteristics of vertical borehole coal samples of Greenhills multiple seams in the vicinity of Elkford, British Columbia were investigated. Three vertical boreholes at depths of 335 m, 380 m and 395 m were drilled along the west wall of an active open pit mine and 44 core samples from various coal seams were obtained for desorption studies.The results are presented in three tables and illustrated with six figures. The methane content was found to increase significantly at depths greater than 200 m. The adsorption equation by Kim and the properties of the coal have been used to predict the methane content and these were compared with the measured values by the direct method.IntroductionThe coalification of plant material in the sedimentary rock produces different ranks of co al and gases of various composition. The gas mixtures are retained in coal beds and rock strata under pressure. The gas content in a coal bed varies considerably depending on the rank of coal and the depth of overburden. The gas content is defined as the volume of gases adsorbed in a unit weight of coal materials. The net amount of gases remaining in a coal seam depends on the difference in the rate of generation of methane by geo-thermal heat and the rate of diffusion of the gases out of the coal bed through sedimentary cover. The major factor that causes the change in rank and the liberation of gases is the temperature, which is governed by the thermal conductivity of sedimentary cover and the heat flux through the underlying rocks. The rate of diffusion of the gases out of the coal is governed by the porosity of the overlying rocks and the degree of fracture. The measured values of gas content in major North American coal beds are from zero up to 24 cm3 per gram of coal(1,2). A gas content of 2.5 to 9 cm3/g is considered ""gassy"" and that of 9 cm3/g or higher is considered ""very gassy"" for underground mining(3). Normally, the gas mixtures released from bituminous coal in Canada contain 90 to 98% methane and the remainder is made up of CO2, N2, 02, H2, He and other hydrocarbons(4)."

Jan 1, 1984

By Louis J. Cabri

"Mineralogical evaluation of ores containing platinum-group elements (PGE) is fraught with difficulties because of the low grades (often 1-3 g/t PGE), dispersal of PGE (usually as finegrained platinum-group minerals [PGM]), as well as occurring in solid solution in some base metal sulphides (BMS) such as pentlandite and pyrrhotite. Mineral processors not only need to know how the PGE are distributed, that is, their mineralogical distribution, but the grain sizes of the PGM, and especially the associated minerals.After obtaining a representative ground sample, common approaches include studying a large number of polished or polished thin sections, concentration of the PGM and sulphides by different gravity methods (e.g., heavy liquids, elutriation, micro-panning) and study of the produced concentrates. Unfortunately, these methods often do not produce concentrations that are sufficiently representative of a particular ore. The newly developed patented technology of hydroseparation (Rudashevsky et al., 2002) is especially effective at making concentrations of PGM over a wide range of concentrations (down to <300 ppb Pt+Pd+Au) and size fractions, including <45µm (down to a few micrometres in size), a size range not possible by other techniques. This water-based environmentally friendly laboratory technique provides a large amount of data from samples, which can range from 5 to 1000g, giving confidence to extrapolation of results to bench-scale and larger test work, especially when combined with quantitative image analysis to determine modal percent of major minerals and mineral liberation data, needed to predict the minimum (K80) and optimum (K40) grinds. INTRODUCTIONThe invention of the electron microprobe in the early 1960’s and scanning electron microscopes (SEM) with energy dispersive spectrometers (EDS) in the 1970’s presented mineralogists with powerful tools permitting them to obtain chemical and surface area data on minute amounts of minerals in situ, in a non-destructive manner. An area of process mineralogy that has very much benefited from this new technology was the characterization and understanding of PGM species, resulting in rapid growth of newly characterized species (Figure 1). Recognition of the first PGM may be ascribed to the Spanish explorer Ulloa in 1748, who described native platinum from South America. The second PGM (laurite, RuS2) was only recognised in 1866 by Wöhler in placer samples from Borneo (now Kalimantan) and the third (sperrylite, PtAs2) by Wells in 1889 from the Sudbury Ni-Cu sulphide deposits. The discovery of the important Pt-Pd deposits in the Bushveld Igneous Complex led to the characterization of the important Pt-Pd sulphides (cooperite, PtS2 in 1928 and braggite, (Pt,Pd)S2 in 1932). By the early 1960’s, only about 20 PGM were recognised, and many later proved to be poorly or incompletely characterized. Thus, the introduction of electron probe microanalysis (EPMA) led to a 50% increase of known PGM, as shown in a 1972 review on PGM (Cabri, 1972). At the time of the next review in 1981 (Cabri, 1981) the number of known PGM had grown to 75 and as of 2002, it had increased to 109 (Cabri, 2002). However, it is the author’s experience that less than about 25 PGM may be considered to be “common”, i.e., found in many different deposit types, as shown in Table 1, but usually only some of these occur in any one particular deposit."

Jan 1, 2004

By S. Bellec, P. Champagne, J. Châteauneuf, A. Berton, S. Fortier

"The start-up of new plants, extending from the commissioning of equipment to the production ramp-up, is a critical period where the processing circuit operation must be done in a structured and well controlled way to enable the gradual, safe and rapid achievement of production targets. The magnitude of the many risks associated with this pivotal period is accentuated in the actual context of low commodity prices. However, the implementation of a method that analyzes risks associated with a start-up, their probability of occurrence and their impacts leads to the identification of a series of preventive actions that can be applied in order to reduce potential negative impacts.Soutex has been involved in numerous start-ups over the last few years and has developed a structured methodology to assess this crucial period, maximize the pre-start-up preparation, ensure a smoother and safer ramp-up period and minimize the time needed before reaching commercial production.This paper describes a method to identify preventive actions to apply in order to reduce risks related to a plant start-up. Then, the various steps of the method are demonstrated using the industrial case study of the Canadian Malartic gold plant situated in Abitibi, Québec. The specific preventive actions, during start-up, the organisational measures and the ramp-up plan are detailed as they were effectively achieved. Finally, the post start-up actions are presented as well as some key results illustrating the achievement of their prior defined objectives.IntroductionPlanning a new plant or new circuit start-up in a mine installation involves various risks, both at the economical and safety levels. Unprepared staff and equipment can lead to safety issues that could threaten plant staff as well as the environment. Moreover, a poorly prepared start-up could often lead to equipment break-down, production stoppages and delays, leading to important economic impacts, delaying commercial production and therefore affecting directly the profitability of mining projects.It is common in the industry to have structured commissioning procedures for major equipment taken separately. Technical personnel from the equipment manufacturing company would usually come on site in order to perform the pre-operation verification, dry runs and the first hours of operations. This kind of assistance is usually focussed on one piece of equipment and neglects the interactions between the various equipment of the production chain. The commissioning phase is usually maintenance oriented and the information given by the manufacturing representative seldomly flows through the operation staff (in the case of this paper, the denomination “staff” refers to both managing and operating employees). The global process is usually not taken into consideration by the technical personnel sent on-site by the manufacturer during the commissioning phase. Many papers can be found describing the commissioning of new equipment focussing on the technology (Côté and Adante (2009), Wells et al (2007)) but without dealing with its integration process in the complete production chain."

Jan 1, 2016

By J. Koponen, K. S. Stadler, A. Fuerst, S. Gaulocher, Th. von Hoff, R. Veldsman

"Gearless mill drives (GMDs) are the workhorse in the mineral processing industries, more specifically when it comes to grinding crushed ore and cement (in various production stages) in semiautogenous (SAG) mills and large ball mills. They are renowned for their excellent reliability and robustness, long lifespan, and little need for maintenance, and thus yield a low total cost of ownership (TCO).A GMD represents a major investment for a mineral processing plant, and its availability is pivotal for the grinding process. As a basic rule, shut-down periods are to be minimized, but even much more important is that unscheduled shut-downs be avoided. In this contribution, we will present a portfolio of innovative remote diagnostic that consist of the following three key components:1. Trouble shooting is a form of corrective maintenance and is based on state-of-the art remote access technology, thus enabling highly skilled engineers to access the current sensor readings anytime and from anywhere in order to resolve urgent problems together with the GMD user.2. Periodic maintenance reports are a form of preventive and predictive maintenance and aim at continuous improvement based on long-term historical records and analyses of multiple measured signals. These detailed reports highlight the health and operational status of the GMD and are periodically (e.g. 3 months) submitted to the customer.3. Remote condition monitoring spans across preventive and predictive maintenance and is based on continuous recording and automatic analyses of relevant signals using advanced algorithms. The main issue is how to handle the enormous flood of data in an intelligent manner. The results of these analyses are made available to both the GMD user and supplier in real time in order to increase the availability and reliability of the GMD.In this paper, we consider various parts of the GMD, e.g. the cycloconverter, the ring motor, the auxiliary devices (e.g. cooling and lubrication systems), and also phenomena related to the mill itself (e.g. state and quantity of charge). The signal analysis techniques range from simple threshold-based analyses to complex time and frequency domain analyses. We will illustrate the benefits of the proposed approaches with some selected examples."

Jan 1, 2012

By G. J. Borbely, E. A. Devuyst, V. A. Ettel

"A new method for oxidative destruction of cyanide in industrial waste waters and slurries, such as gold mill barren liquors, tailing slurries and flotation tailings has been developed at the Inca research laboratories. Rapid decomposition of cyanide and related species is attained by treating the waste waters with a mixture of S02 and air at controlled pH and in the presence of a small amount of copper which acts as a catalyst. The approach selectively oxidizes cyanide and metal cyanide complexes, and also removes iron cyano complexes which are not removed by alkaline chlorination.The new method is shown to be less reagent intensive and therefore more economical than alkaline chlorination for treating gold mill and flotation waste waters. INTRODUCTIONOver 90% of the gold mined in Canada is extracted from the ore by ""cyanidation"". Wastes from the process consist of tailings which contain free cyanide, cyanide combined with heavy metals, thiosalts and thiocyanates. Because of the concern over the effect of toxic cyanides on the environment, all cyanide containing effluents will have to be treated in the future to meet certain government set concentration limits."

Jan 1, 1982

By Don Thompson

It isn?t a lie if you don?t tell the whole truth The pictures National Geographic didn?t print Other photos National Geographic didn?t print?

May 1, 2009

By G. Lee, E. T. C. Spooner

"Molybdenum mineralization at Boss Mountain is hosted by the Triassic Takomkane quartz monzodiorite batholith and is associated with a Cretaceous monzogranite stock. Ore has been mined from a sheeted vein system that describes a partial annulus centred upon the apical region of the stock and from subvertical breccia pipes that emanate from the stock. Molybdenite precipitation is coincident with CO2 effervescence from a dilute (1.9 mole o/o NaC/ equivalent) hydrothermal fluid over a temperature range of 250°C to 370°C at a pressure of approximately 350 bars, interpreted to be greater than or equal to the lithostatic load and equivalent to a depth of 1.3 km or less.IntroductionThe chemical and thermal constraints on molybdenum transport and deposition to form molybdenum ore deposits are not well understood. To address this problem, the Boss Mountain mine in central British Columbia, operated by Noranda Mines Ltd., was chosen as a well-described (Soregaroli and Nelson, 1976), relatively small and simple example of a Cordilleran Mo~ deposit. It is situated on the northeast slope of Takornkane Mountain, 10 km west of the community of Hendrix Lake (N.T.S. 93A/2W; latitude 52°06'N, longtitude 120°56'W). Access is from 100 Mile House by nearly 90 km of road, the first 50 km of which are paved."

Jan 1, 1995

By G. L. Palmer

"In 1986, anomalous sampling results for heavy minerals were obtained at various sites in Namaqualand on the west coast of the Cape Province. Drilling in 1987 at Graauwduinen penetrated up to 35 meters of heavy mineral-bearing Tertiary sands which extend several kilometers inland from the coast. The heavy mineral suite includes ilmenite, rutile, leucoxene, zircon and monazite, along with gamet, pyroxene and amphibole. Three deposits are recognized, two of which comprise the resource to be mined by Namakwa Sands Limited, a recently formed Anglo American Corporation subsidiary company.Mineable reserves in excess of 500 million tonnes have been delineated, sufficient to sustain mining for over 35 years at projected production rates. During the feasibility study, on-site investigations included test mining at various sites to assess rnineability and to provide material for metallurgical testing in a pilot plant located at the site. llmenite produced at the mine will be smelted at a new facility to be built at Saldanha Bay. Saleable products comprise titania-rich slag, pig iron, zircon and rutile.During the exploration phase, company environmental guidelines were established and monitored. The feasibility study incorporated a Class 1 Environmental Impact Report, the contents of which were made public following the principles of the Integrated Environmental Management legislation."

Jan 1, 1994

By Laura Prati

Gold-on-carbon catalysts resulted very active and selective in liquid phase oxidation [1, 2, 3] and during past studies we established that activity is ruled by two factors: particle dimension and gold exposure on the carbon surface [4]. These two parameters are also connected to the nature of activated carbon where the chemical nature of the surface oxygenated groups probably plays an important role [5]. Our studies, focused on the design of an active gold-on-carbon catalyst for liquid phase application, were aimed, operating a fine tuning of all the parameters involved in determining activity, to optimize gold-on-carbon preparation, keeping in mind that gold particle activity increases with decreasing particle size and increasing gold exposure. Gold sol immobilisation represents a versatile methodology in preparing gold catalysts [6]: throughout this work we used as sol stabilizing agent, the N-dodecil-N,N-dimethyl-3-amino-1-propan sulphonate (SB), that provides both sterical and electrostatic stabilisation, a condition we already demonstrated necessary to preserve particle dimension when carbon is used as the support [6]. We generated different gold sols by varying the relative amount of reagents (HAuCl4, SB, NaBH4), the type of alkali and the temperature of the gold precursor reduction. Moreover, as we had recently evidenced that there is also a carbon effect [5], we employed only one active carbon to immobilize the sols.

Oct 1, 2003

By K. Swedburg, M. Samuels

"The New Afton concentrator was commissioned in June 2012, reaching the design milling rate in September 2012. By late 2013, through a campaign of optimization and de-bottlenecking, it was recognized that the installed plant was capable of greatly exceeding the design throughput of 11,700 tpd. Because the value of the metal contained (by increasing the plant feed rate) exceeded the offsetting losses of copper and gold recovery (as the operation moved to a coarser grind), the concentrator feed rate was strategically increased with support of New Gold, while the operations team was given a mandate to evaluate, and then implement, flow sheet options that could re-establish the original design criterion grind target and achieve the corresponding improved recovery. Broadly, the two options implemented were the addition of a tertiary grinding stage consisting of Metso Vertimill® prior to rougher flotation (in order to address the grinding required at increasing throughput by increasing the power), and the addition of three Woodgrove Staged Flotation Reactors (SFR) added to the cleaner circuit after regrind of the rougher concentrate (to address the increased mineral loading to the cleaner circuit). Through test work, it was anticipated that the SFRs would be capable of achieving final concentrate grade in a single pass without the integration of recirculating loads, a strategy sometimes referred to pre-cleaning. This paper describes the expectations generated for the Woodgrove SFR unit operation through pilot plant testing on site, and compares those results with the performance of the expanded circuit that exceeded the original design criterion of P80 160 µm, which was commissioned in the second quarter of 2015.INTRODUCTIONThe New Afton concentrator, located near Kamloops, BC Canada, commenced operation in June 2012. The mill achieved the design throughput of 11,000 tonnes per day average during the month of September 2012 and, following various operational optimization efforts (O’Hara et al, 2015), achieved the design p80 grind size of 160 µm at the design milling rate in July 2013.During August 2013, trials were carried out to determine the throughput rate limits of the mill circuits and to evaluate mill metallurgical performance at higher rates. Milling rates up to 15,500 dmt per 24 hours were achieved during this trial, demonstrating potential capability for sustained milling rates exceeding the nominal design capacity. As was expected, the higher milling rates resulted in a coarsening of the grinding circuit product size, and resulted in marginally lower recoveries in the rougher flotation circuit. Despite the lower recoveries, the higher milling rates resulted in higher metal production and the financial analysis favored running at rates of at least 13,000 tonnes per operating day, with the higher cash flow in the near term offsetting the value of metal production loss at the end of the mine life (due to the short term increase in the rate of reserve depletion). Milling rates were sustained above 13,000 tonnes per day through the second half of 2013, and increased above 14,000 tonnes per day by mid-2014 (Figure 1)."

Jan 1, 2016

By Stephen A. Gasiorowski, Frank J. Hrach, James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity - up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle-particle contact. The small gap, high electric field, counter-current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in North America and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Jan 1, 2012

By D. J. Lloyd

"Bending is involved in the forming of many sheet parts and it is important to understand the phenomena involved. In this paper the basic equations describing bending on a global scale are compared with strain measurements of bent sheet. The development of strain on a local, microstructural scale is also investigated, as is the general aspects of plasticity and the failure process. It is shown that the global equations can be used to estimate the strains involved and the local strains can be attributed to various aspects of the plasticity. The bendability can be related to the fracture strain of the sheet and the ability of a sheet alloy to accommodate the necessary bending to form the part can be assessed.INTRODUCTION The ability of a sheet alloy to undergo bending without failure is an important capability in the forming of many parts and it is useful to be able to assess the bendability of an alloy during its development. The basic mechanics of bending were developed in the 1950s (Lubhan & Sachs, 1950; Hoffman & Sachs, 1953). When a sheet is bent the upper bend surface is in tension, the lower surface in compression and at some point within the sheet there is a plane of zero strain which is referred to as the neutral axis. For sheet exhibiting limited plasticity the neutral axis is static and occurs at the mid-point of the sheet thickness but for sheet exhibiting extensive plasticity the neutral axis progresses deeper in to the sheet as bending progresses. This results in two expressions for the maximum strain at the upper bend surface depending on the motion of the neutral axis. For Al alloys such as AA6111, AA6016 and the like extensive plasticity occurs and the neutral axis is expected to move during bending. However, very few studies have examined how the neutral axis motion and the strains develop, compared with the mechanics analysis. Geist and Parker (1984) used hardness measurements to investigate neutral axis motion but these experiments did not have the resolution necessary to compare the results with experiment but did indicate neutral axis motion. To understand the nature of plasticity and failure during bending it is important to know the extent of neutral axis motion, the scale of strain gradients developed through the sheet and the maximum strains occurring at the bend surface, finally comparing experimental results with the theoretical predictions. The influence of microstructure on the evolution of strain and failure can then be considered in the context of these parameters. Recently, bending in some automotive Al alloys has been reported mainly from the microstructural perspective (Lloyd, 2000, Lloyd et al., 2002, Mattei et al., 2013) and FEM studies have also investigated the development of plasticity under bending, demonstrating the tendency for strain localization (Becker, 1992, Shi et al., 2014)."

Jan 1, 2018

By P. Mattar

The geotechnical importance of studying fluid flow through porous media and soils in particular, becomes evident when dealing with groundwater movement in surficial geomaterials that can be initiated by hydraulic gradients that develop during construction activity, groundwater extraction, impounding of reservoirs and groundwater recharge during adverse climatic events. In a geotechnical context, rocks are regarded as virtually impermeable materials, with comparatively greater resistance to flow of water through their pore structure. The importance of the permeability of rocks comes to the forefront when deep geologic formations are used in geoenvironmental activities for disposal of hazardous and toxic materials. The permeability of the rocks encountered is of critical importance to these geoenvironmental activities since the movement or transport of the hazardous materials during their eventual release will be largely governed by the permeability characteristics of the geologic formation. The estimation of the permeability characteristic of geologic formations is a non-trivial exercise since the measure of permeability can be influenced by the scale at which the measurement is made. Regional-scale and borehole-scale estimates of the permeability can be greatly influenced by the inhomogeneities, including fractures, fissures, solution channels and other anomalies that are present in naturally occurring geologic media. These anomalies are considered to be site specific and can only be determined in a reliable fashion by either conducting tests at the appropriate scale or in the regional-scale through inverse analysis of tracer movement patterns in rock masses. The estimation of the permeability of intact units of a geologic medium has important geoenvironmental applications in connection with storage of wastes since the units in which repositories will be located should be sparsely fractured and the sealing of the fractures and fissures are a prerequisite to developing an efficient solution for storage. The intact permeability of geomaterials is therefore regarded as an important property that influences efficiency and reliability of geoenvironmental solutions for deep geologic disposal. The permeability of geomaterials such as concrete and cementitious grouts are also important to many geoenvironmental and infrastructure applications where durability of structural materials in general and cements used for sealing deep boreholes and other access shafts employed in waste management endeavours is influenced by the permeability characteristics of these materials

May 1, 2009

By Z. D. Hora

Limestone of economic interest is widespread in British Columbia. Triassic deposits on Texada Island are a convenient 1idewa1er source of li111es1one for cemen1 and lime for 1he Pacific orthwes1. Permian limes/one near Pavilion Lake is used for quicklime, and a deposit near Kam/oops is used for cement. Quarries at Dahl Lake and Pwrmigan Creek serve local pulp and paper needs.

Jan 1, 1984

By T. L. Lee, D. Y. Tan, J. Mi

Considerable progress has been made in studying the mechanism and effectiveness of using ultrasound waves to manipulate alloy solidification microstructure, However, uncertainties remain in both the underlying physics of how microstructure evolve under ultrasonic waves, and the best technological approach to control the final microstructure and properties. We used the ultrafast synchrotron X-ray phase contrast imaging facility housed at the Advanced Photon Source, Argonne National Laboratory, USA to study in-situ the highly transient and dynamic interactions between the liquid metal and ultrasonic waves/bubbles. The dynamics of ultrasonic bubbles in liquid metal and their interactions with the solidifying phases were captured in-situ for the first time. The experiments were complemented by the simulations of the acoustic pressure field, the pulsing of the bubbles and the associated forces acting onto the solidifying phases, providing more quantitative understanding for using ultrasound to control the growth of dendritic grains and to enhance grain multiplication effects for grain refinement.

Jan 1, 2014

By Paul Semple

"In 2007, Noront Resources Inc. discovered the high grade nickel copper PGE deposit in northwestern Ontario in a region now known as the Ring of Fire. Since the initial discovery, Noront has advanced the Eagle¹s Nest Project and in September 2012 released a feasibility study for the development of the Eagle¹s Nest Project. This paper summarizes the results of this recent study and outlines additional work planned in the next stages of project development. INTRODUCTIONThe following paper summarizes the findings of the recently completed feasibility study on Noront Resources Ltd.’s Eagle’s Nest Project. The feasibility study was compiled into a NI 43-101 report by Micon International. This paper is intended to summarize the major technical findings and for complete information, interested parties can find the entire NI 43-101 report at www.norontresources.com or on SEDAR.LOCATIONThe McFaulds Lake project area, which includes the Eagle’s Nest deposit, is located at approximately UTM 5844000 N and 547000 E, and between approximately 52º42’ and 52º50’ N latitude and 86º06’ and 86º24’ W longitude, approximately 250 km west of the community of Attawapiskat on James Bay and 575 km northwest of Timmins. The closest all-season accessible community to the McFaulds Lake project area is Nakina, 300 km to the south, where there is a paved airstrip, in addition to all weather road and railroad access (see Figure 1).The First Nations communities of Webequie and Ogoki/Marten Falls are located 90 km west and 120 km south southeast of McFaulds Lake, respectively. Both communities are served by regularly scheduled air service, primarily from Thunder Bay; both Thunder Bay and Timmins serve as support centres for the James Bay communities and the exploration projects in the area."

Jan 1, 2013

By D. Racicot, T. Hanel, E. H. Chown

Over thirty plutons in the Chibougamau-Desmaraisville belt were examined briefly in the field and sampled, in addition to the few masses that have been studied in detail. The survey indicates that the intrusions may be conveniently grouped in four main categories, based on their time of intrusion. These are; remobilized basement domes, pre-kinematic intrusions, syn-kinematic intrusions and postkinematic intrusions. Basement domes, as exemplified by the Lappa rent Massif, are composed of migmatized tonalite-diorite gneiss that has undergone at least two periods of mafic dyke intrusion and at least three major deformational periods. The rise of the basement domes was accompanied by extensive mylonitization and the intrusion of syn-tectonic plutons. Pre-kinematic plutons, such the Chibougamau pluton, are diori te-tonalite in composition, and were intruded into the supracrustal pile and partly eroded before the main deformation of the belt. Syn-kinematic plutons occur principally as marginal intrusions bordering the belt (Barlow), or as discrete intrusions along structural highs (La Dauversiere), and are either hornblende monzodiorite or tonalite in composition. Post-kinematic plutons, such as Muscocho, are principally granodiorite and often porphyritic intrusions locally deforming the enclosing rocks. The close relationship between mineralization and high-level intrusions such as the pre-kinematic and some of the post-kinematic plutons is discussed.

Jan 1, 1984

By K. C. Lahiri, H. P. Das, G. G. Sarkar

"The petrographic components of any particular rank of coal often show some distinct physical and chemical characteristics. Therefore, their pro-portionate distribution in a coal greatly influences the technological behaviour of the coal.In any size or gravity separation of a coal, the petrographic constituents become segregated to different degrees in some preferred size or specific gravity range. Therefore, a knowledge of the petrographic nature of the washed and/or screened fractions is often considered essential in selecting the most efficient method for coal preparation and in exploring the proper evenues for its utilization.A graphical method is described in this paper to indicate the mineral-matter content and the petrographic components of the washed fractions of a coal at different ash levels of separation in the form of a new washability diagram. This diagram can be conveniently used to assess or predict the petrographic composition of clean coal or sinks corresponding to any desired ash level in the cleans. With the help of this diagram, it is also possible to locate the yield level of cleans at which maximum enrichment of vitrinites and exinites occurs with the least amount of mineral-matter content."

Jan 1, 1971

By J. W. Stickney

"On July 1, 1977 Hudson Bay Mining and Smelting Company Limited announced the commencement of construction of a 3800 ton per day concentrator at Snow Lake, Manitoba. Snow Lake, a community of 2200 people, is located 130 road miles from the main metallurgical plants at Flin Flon.The design, detailed engineering and equipment selection for the project was awarded to Wright Engineers Limited of Vancouver, B.C., who would be working in close liason with Hudson Bay Mining personnel throughout the project.The feasibility of constructing a metallurgical plant in the Snow Lake area, in addition to the concentrator at Flin Flon, had been under study since 1964 with plants of varying capacities and designs being considered. Each successive study recommended a plant of increased capacity and sophistication and finally upon an in-depth study in 1976 of ore reserves, freight rates and operational benefits, the construction of a 3800 ton per day copper-lead-zinc concentrator appeared highly benificial."

Jan 1, 1981

By P. V. Barr, Y. -H. Li, A. P. Watkinson

Subsequent to a campaign of pilot-kiln trials of firing bio-oil and natural gas, scale-up to commercial lime kilns was made using an in-house mathematical kiln model. Both dry limestone and lime mud kilns of 3.5 m OD. by 100 m length were used for bio¬oil firing simulations. Comparisons were made against natural gas firing on the basis of specific firing rate, off-gas volume, energy consumption and overall lime quality. Model simulation results indicate that conversion from natural gas to bio-oil with no productivity loss will increase energy comsumption by about 7.5% and total off-gas volume by about 8%. Alternatively, a 6% decrease in productivity would be expected if off-gas volume is maintained constant. The calculations are sensitive to deviations in the lower heating value (LHV) used in the simulations. A 5% increase in the LHV of the bio-oil, which could result from a 3% decrease in the moisture content, reduces the energy penalty to 2% coupled with a slight reduction in off-gas volume.

Jan 1, 2004