Search Documents

By M. Rafati

In this investigation, the effects of T4 and T6 heat treatments of AZ91 magnesium cast alloy have been studied. The effects of different microstructural details such as morphology, size and distribution of precipitates and their influence on fracture mechanisms were investigated by optical and scanning electron microscopy. The mechanical strength of the alloy after T6 treatment was found to increase in comparison to the T4 treatment, due to the formation of discontinuous precipitates in the grain boundaries. Precipitation in this alloy occurs in two ways: continuous precipitation, which nucleates and grows inside the grains, and discontinuous precipitation, which forms at the grain boundaries. During ageing, the length of the continuous precipitates increases, and, hence, interprecipitate distance decreases. The formation of discontinuous precipitates causes initiation and propagation of cracks at and the weakening of the grain boundaries. This is the principal reason for the reduction of the ultimate tensile strength in T6 heat treatment in comparison to the T4 condition.

Jan 1, 2006

By Keith Donovan

Why are we here? Improve equipment performance & health ? Eliminate undesirable downtime and expensive secondary damage ? Maximize equipment life, optimize running costs (reduce costs) ? Improve safety and environmental performance ? Capture and consistently apply equipment knowledge ? Improve Proactive Maintenance processes & practices

May 1, 2009

By K. Buxmann

Climate change is a subject of growing concern. Based on the International Energy Agency, about 19% of man made greenhouse gas emissions globally are generated by the transport sector. This paper will focus on the environmental aspects of the light-weighting in transport and the resulting savings of fuel and electricity. Aluminium is an option for lightweight applications in transport, with very high benefits not only in the use stage, but also in the stage of vehicle recycling. Life cycle assessment is used to quantify the relative benefits of light-weighting specific components of cars, commercial road vehicles, buses, ships and trains. A vehicle consists of many components, which are produced by different processes and undergo different types of end-of-life operations. This document does not intend to compare a generic aluminium vehicle with a generic "heavy materials" vehicle. It rather tries to use a pragmatic approach based on specific examples of components where aluminium is used and can be used in the design of new vehicles, also taking into account future developments. The case studies in this paper are based on real cases where aluminium was used. For each component, sensitivity analyses are applied to see the impact of specific parameters such as the end-of-life recycling rate and the use stage driving distance. Significant greenhouse gas savings by the use of aluminium are demonstrated for cars and even higher ones for trucks, buses, trains and ships. In addition, the total potential benefits of light-weighting with aluminium are shown on the global level.

Jan 1, 2007

By G. Gabra, M. Nagamori, J. J. Panneton

"RESUMELa calcination contrôlée de 10 serpentine permet de produire de 10 magnésie active. Le degré de I'activation est mesure par 10 solubilité du magnésium dans les acides faibles tel que I'acide acétique, La serpentine contenue dans les résidus d'amiante du Québec peut donc être activée par calcination. Le teneur en magnésie active des rejets d'amiante calcinés est fonction de divers paramètres: température, temps de calcination, granulométrie, etc. Les rejets d'amiante de différentes provenances démontrent des comportements thermochimiques différents qui sont étudiés dans Ie présent travail au moyen d'ATD, de TG, de la diffraction des rayons X et de la lixivation par l'acide acétique. On constate qu'un maximum d'environ 80% de la magnésie totale peut être activé dans certains rejets d'amiante du Québec et Ie degré d'activation dépend de la provenance.vIntroductionOn sait depuis longtemps que la serpentine, Mg3Si2O5(OH)4, un silicate hydroxylé de magnésium, devient amorphe lorsqu'elle perd de I'eau d'hydratation entre 600 et 700 °C. La serpentine ainsi calcinée est alors dissociée en magnésie et en silice. Cette magnésie, dite active, est soluble dans un acide faible ou même dans les solutions de sels d'ammonium.Plusieurs precédés chimiques ont été proposés afin d'extraire sous forme de composés magnésiens la magnésie de la serpentine. La plupart de ces procédés comportent une activation par calcination de la serpentine préalablement à une Iixiviation par un acide ou par une solution d'un sel d'ammonium.Malgré la contamination par Ie fer et par d'autres éléments, les compositions chimiques des rejets de différentes mines d 'amiante du Québec, présentées au tableau 1, sont très proches de la serpentine typique. Puisque Ie degré d'activation de la magnésie varie grandement d'une serpentine à I'autre lors de la calcination, la première étape de la recherche sur la transformation chimique des rejets d'amiante du Québec se résume à une étude de leurs comportements thermochimiques."

Jan 1, 1982

By K. Schimann, H. D. Knipping, J. P. Fouques

"RESUMELe gisement d 'uranium de Cigar Lake, dans la région de l'Athabasca au nord du Saskatchewan, fut découvert en mai 1981 par Cogema Canada Ltée, opérant pour Ie compte de la ""Waterbury Lake Joint Venture"".Le corps minéralisé. qui est dépourvu de toute expression directe en surface, est situé a la discordance entre les met sédiments du wottaston Group (Protérozoïque inférieur ou Aphébien) et les grès de l 'Athabasca (Protérozoïque moyen ou Hélikien), à une profondeur de 410 a450 m.Fin 1984, Ie gisement était reconnu par 105 sondages minéralisés repartis sur une longueur de 1800 m, pour une largeur comprise entre 25 et 105 m. 11 se présente sous forme d’une lentille aplatie de 5 a30 m de puissance, et montre une remarquable continuité d'ensemble. Une ride ou bombement topographique de la discordance est associée au gisement surtoute sa longueur.A l'échelle régionale, le corps minéralisé à est associe à un corridor structural d’orientation est-ouest, a l'intérieur duquel des facies particuliers aténdance blast mylonitique sont développes dans les formations métapolitiques agraphite du socle métamorphique. Il est entouré par un halo d'altération très important, caractériser Ie développement de minéraux argileux alumino-magnesiens (illite-chlorite).La minéralisation est située, pour la plus grande part, dans les grès d'Athabasca, et se compose essentiellement d'uraninite et de sulfo-arseniures de nickel et de cobalt,De nombreux levés géochimiques et géophysiques ont été effectues dans la région de Cigar Lake. Aucune anomalie ne peut être associée directement au corps minéralise, mais la combinaison des données en provenance de plusieurs sources s’est révélée fort utile au niveau de l’interprétation géologique régionale et de la définition des cibles de sondages a l'intérieur des zones reconnues favorables.Le gisement de Cigar Lake présente de nombreuses analogies avec plusieurs des gites classiques de la région de l'Athabasca; il est caractérise en particulier par l'intensité des phénomènes d’altération et la présence de minéralisations extrêmementriches.En 1984, les réserves géologiques globales estimées par géostatistique sur I ‘amas minéralise principal s 'élevaient a 110 000 tonnes d'uranium, aune teneur moyenne de 12.2%, avec une précision de 25% à l'intervalle de confiance de 95%.ABSTRACTThe Cigar Lake uranium deposit, in the Athabasca area of North Saskatchewan, was discovered in May 1981 by Cogema Canada LId., as operator of the Waterbury Lake Joint Venture. The deposit, which is devoid of direct surface expression, is located at the unconformity between the Lower Proterozoic (Aphebian) Wollaston Group meta-sediments and the Middle Proterozoic (Helikian) Athabasca sands tone, at a depth of 410 m to 450 m below surf ace.AI the end of 1984, the deposit had been defined by 105 mineralized holes over a length of 1800 m and a width of between 25 m and 105 m. It has the shape of a flat-lying lens 5 m to 30 m thick and shows a remarkable longitudinal and latera continuity from the information obtained to date. A well-defined bulge of the unconformity underlies the mineralized zone over its entire length.The deposit appears to be controlled by an east-west-trending structure within which a particular rock facies (""augen gneiss"") has developed in the graphitic metapelites of the Wollaston Group. It is surrounded by a strong alteration halo affecting both sandstone and basement, characterized by extensive development of Mg-A I rich clay minerals (illite-chlorite).The mineralization is hosted principally by the Athabasca sandstone, and consists mainly of uraninite and sulfo-arsenides of nickel and cobalt.Numerous geochemical and geophysical surveys have been carried out in the Cigar Lake area, and no specific geochemical or geophysical anomaly can be directly associated with the mineralized body, although there may be locally a good coincidence. However, a combination of several methods proved extre"

Jan 1, 1986

By G. Song

This paper reports the anodizing voltage, gas evolution and sparking behaviors of an anodized coating formed on AZ91D in a silicate containing solution. According to their responses to an anodizing current, a four-stage anodizing mechanism is proposed. At the same time, the formed coating is characterized in terms of its microstructure, composition, thickness and corrosion performance. It was found that deposition of MgSiO3, Mg(OH)2 and MgO as well as dehydration of Mg(OH)2 are involved in the anodising process; the vigorous gas evolution accompanied by intensive sparking and the corresponding negative anodising efficiency in the later stage of the anodising process are closely associated with thermal decomposition of water due to the high temperature resulting from the intense sparking on the surface of the anodized alloy; the thickness, porosity, and composition of the anodised coating on a magnesium alloy depend on the final anodising cell voltage; and the corrosion resistance of a thick but porous coating containing more silicates appears to be more corrosion resistant than a thin but compact coating containing less silicates.

Jan 1, 2006

By Hans E. Madeisky, Bruce W. Downing

The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: an orthosite-hosted magmatic sul?de nickel, dunite-hosted magmatic sul?denickel, porphyry copper-gold, and volcanic-hosted high sul?dation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray ?uorescence equipment, already used for grade control at many mine sites, could provide the whole-rock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997

By MacDonald W. L. F. C. A.

IN accordance with the usual approach to a participation in a panel discussion, this paper is, in some respects, intentionally controversial. I would suggest, how-ever that there is more than a grain of truth in many of the comments made. Before dealing with a particular problem. It is appropriate to set out a few of the more significant objective of an: accounting system: (1) The provision of historical data <•concerning past events, for the information of shareholders, tax authorities, etc. This data can also be used as a tool to predict the future. (2) The provision of a record to safeguard the company's assets and to form the basis of any claim for insurance or other damages. (3) The provision of an accounting framework in making an economic study of a proposed course of future action such as the development of an orebody or the outlay of a substantial sum for new equipment. ( 4) The

Jan 1, 1962

By R. S. Boorman, H. G. Ansell

"Poor separation of lead from a copper concentrate of a major base metal producer was thought to have resulted from copper (0.2-0.4%) in the galena which caused it to float with chalcopyrite. No inclusions of copper mineral were detected which could account for the flotation of galena. The tendency for copper-bearing galena to float with chalcopyrite was confirmed by Hallimond-tube experiments in which the floatability of copper-doped synthetic galena (0.1-0.4% Cu) was approximately four times as high as copper-free galena. The difference in the cell edge (5.9338 ± 0.0003 A, Cudoped galena; 5.9361 ± 0.0002 A, Cu-free galena) indicated that the copper was lattice-bound and did not occur as submicroscopic mineral inclusions."

Jan 1, 1973

By Euler De Souza

"The uninterrupted operation of a ventilation system is critical to ensure the mine meets its scheduled production and, as important, is vital to the health and safety of all personnel working underground. Those operating the mine ventilation system must have fundamental engineering training in the art of fluid dynamics and have a good comprehension and control of the mine ventilation network. Ventilation management by untrained and inexperienced personnel may result in serious consequences when the system becomes ineffective. This paper shares observations and experiences pertinent to the occurrence of upset conditions as a result of the improper design and operation of mine ventilation systems. A series of real life case studies are presented to describe disruptions to mine ventilation systems and the gradual deterioration of system operational efficiencies leading to eventual failure. Special focus is given to mistakes made and on the resulting serious consequences. The case studies also demonstrate how each upset condition was resolved, permitting the mines to safely resume production activities.INTRODUCTIONThe ventilation of operating mines is a continuously changing and evolving system; upset conditions will occasionally occur, but should be promptly resolved in order for the system to function properly, according to design, and in compliance.Those designing, managing or operating the mine ventilation system must have pertinent training and have a good understanding of fundamental ventilation concepts to be able to devise and implement engineering solutions to day-to-day challenges. Realistically, the operator must also have extensive practical experience and be able to effectively apply operating procedures, design criteria and ‘best practices’. They must be able to, on a daily basis, evaluate the mine ventilation system, determine and locate any problems, understand the causes of each problem, find a solution, and promptly and efficiently correct those problems.Ten case studies are presented to demonstrate how fundamental design or operational mistakes can lead to adverse conditions or to catastrophic consequences, how detailed on-site engineering assessments can be employed and how simple, low cost, engineering solutions can be implemented to successfully resolve the issues and return the ventilation system to compliance, permitting the mines to safely resume production activities."

Jan 1, 2019

By S. Koski

The Cerro Verde copper-molybdenum porphyry mine, majority owned and operated by Freeport- McMoRan Copper & Gold, is located 30 km southwest of Arequipa Peru. The concentrator, which produces copper and molybdenum concentrates, started operating in late 2006 with a 108,000 tpd design capacity, processing primary sulfide ore (mainly chalcopyrite and molybdenite). Plant capacity was recently increased to 120,000 tpd. The comminution circuit consists of one 60? x 113" primary crusher, four MP-1000 secondary crushers in closed circuit with dry screens, four 2.4m x 1.6m High Pressure Grinding Rolls (HPGRs) in closed circuit with wet screens, and four 7.3m x 11m gearless ball mills in closed circuit with cyclones. The HPGR circuit is fed by the Secondary Crushing circuit product at a T80 of 35 millimeters, and the HPGR circuit product feeds the Ball Mill circuit at a T80 of 3000 microns. This paper describes operating experiences with HPGRs during these first four years highlighting improvements in operating practices and presentation of data regarding operational efficiencies, also discussed are the primary benefits provided by HPGRs such as production of micro fractured particles, reduced ore Bond Work Index, and reduced power consumption. Cerro Verde represents the first installation of HPGRs in both the copper industry and large scale hard rock mining.

Jan 1, 2012

By Simon C. Dominy, Ian M. Platten, Garry F. Johansen, Alwyn E. Annels, Brian W. Cuffley

Abstract - Coarse gold-bearing veins are characterized by high grades that are localized and erratic. Effective sampling of coarse gold-bearing veins is difficult because of the low concentration and erratic nature of the gold particles. Diamond drilling is an effective measure of geological continuity, however, grade distribution can only be reliably obtained from underground development (including close-spaced sampling, bulk sampling, and trial mining). Comparison between surface and underground drilling, underground linear/panel and bulk sampling indicate that drilling and linear/ panel samples generally understate bulk sample grades. Bulk samples are likely to be the closest estimators of true grade. It is unlikely that anything above an Inferred Resource category can be estimated from surface drilling alone, and at best the grade will only be a global estimate. Underground development, in-fill drilling and bulk sampling/trial mining will be required to delineate Indicated and Measured Resources. Closely spaced development and bulk sampling is likely to be the only way to determine Reserves. The resource estimation process must driven by a clear geological model that should attempt to understand both geological and grade continuity. Traditionally, grade interpolation has been undertaken using classical methods, though more recently, computer-based block modelling techniques have been used with some success. Three case histories are presented, documenting the problems of estimating resources in coarse gold-bearing veins and the practical ways in which they were approached.

Jan 1, 2000

By J. A. Chamberlain

DURING a recent trip across Canada and parts of the northern United States, the. writer examined some forty mine models. Construction -details and the uses to which the models were being put were outlined in a report to Eldorado Mining and Refining, Limited, and a specific model was proposed on the basis of the Company&apos;s particular needs at their Beaverlodge operation. It was felt, however, that portions of the report would be of some value to anyone contemplating building a mine model. For this reason, a synopsis of some of the more important aspects of the problem is presented here, together with a suggested model type that appears to have wide application. Thanks are due not only to Eldorado for permission to publish the following material, but also to the many mine personnel across Canada who allowed the writer to examine their models and gave freely of their time in discussion.

Jan 1, 1958

By W. Curlook, V. G. Papangelakis, M. Baghalha

A pressure acid leaching process has been developed for the extraction of metal values, nickel, copper, cobalt and zinc, from base metal smelter slags. The basic concept contemplates cooling the smelter slags through solidification sufficiently slowly to induce a good measure of crystallization; and subsequently, after fine grinding, to pressure leach such slags at around 250°C while applying oxygen overpressure, utilizing smelter byproduct sulphuric acid. High levels of extraction of the slags&apos; metal values are thereby achieved. It has been shown that if the same slags are quenched thereby producing an amorphous structure, the resulting metal extractions are very low. The process is applicable to smelting furnace throwaway/discard/dump slags, as well as to in-process converter slags. By extracting the bulk of the residual base metal values in the throwaway/discard/dump slags, the resulting leached residues are rendered virtually benign vis-à-vis the external environment.

Jan 1, 2004

By M. R. Julien

"The geomechanical behavior of rocksalt shows very distinctive features. The response of this most ductile of all low porosity rocks is dominated by inelastic processes that are strongly time- and historydependent. These characteristics must be taken into account when analyzing underground openings. Different constitutive models have been proposed and used for this purpose, and this paper presents the general formulation and applications of one of these. The SUVIC model relies on a unified approach with internal state variables producing mixed hardening to represent the inelastic behavior, which lead to specific solutions for plasticity and creep. The model equations have been implemented into a finite element code to perform numerical analyses. Simulations results are presented to show that this model captures essential aspects of rocksalt behavior under simple and complex laboratory testing conditions. Simulations are also conducted to analyze the response of underground openings. INTRODUCTIONPredicting the response of man-made excavations in rocksalt can be quite a challenge as it requires a reliable constitutive model to represent the material behavior. This softest of all low porosity rocks shows a highly non-linear inelastic behavior, very sensitive to history and rate effects (e.g. Senseny et al., 1993; Cristescu & Hunsche, 1997; Julien, 1999; Wittdke, 2014). The many deformation (micro) mechanisms acting locally in rocksalt make the construction of appropriate constitutive equations quite complex. Nonetheless, there have been significant progresses made over the last two decades or so; many of these developments have been included in a series of specialized Conferences Proceedings (Ghoreychi et al., 1996; Aubertin & Hardy, 1998; Cristescu et al., 2002; Wallner et al., 2007; Bérest et al., 2012)."

Jan 1, 2015

By C. L. Popp

The scope is to address issues confronted by parties in the mining industry such as: Mine planners, survey and engineering departments, field teams and subcontractors. Describing approaches and best practices for assembling a project team to identify and create modeling requirements and to implement beneficial results. 3D Machine Control and Guidance tools continue to reduce project risk and attract quality resources with skill sets new to the earthmoving industry. These tools increase production, reduce rework and help with government permitting.

May 1, 2013

By X. (Mike) Yao

Rock mechanics engineers must provide ground support designs that ensure a safe underground working environment. Unexpected falls of ground are unacceptable while ground support systems must be adequate. Ground support must be economic for the area supported and the time frame the opening is in use. While numerical modeling can be used for ground support design, empirical models are still the common useful design tools. Empirical models are best developed and improved from local experiences although some models, such as Stability Graph (Potvin et al, 1992), are in extensive use by the Canadian mining industry. To determine the adequacy of ground support practices at HBMS, a database of 50 fall of ground case histories between 1985 and 2001 was compiled. For each failure, the recorded data included: location, rock type, rock mass conditions, opening and failure geometry, installed ground support and failure mechanism. An analysis of the database was done to obtain an understanding of failure frequency association with rock types, stope geometry and installed ground support, and to assess what support design changes were necessary. The paper describes changes made to ground support and mining practices during the last five years, and the formation of new ground support standards and practices which have been successful in reducing ground falls while providing improved, efficient and economical ground support.

May 1, 2002

By Wignall. T. K., J. De Geoffroy

Statistical models are fitted to the observed distributions of eighteen characteristics of the population of commercial porphyry deposits of North and South America. The statistical base required for the formulation of the statistical models includes 58 commercial porphyry-copper-molybdenum deposits of the Cordilleran Belt from which geological, geometric and economic data were collected. Predictive and composite models are derived from the statistical study to assist explorat10n. planning, engineering studies and fmanc1al analyses as required for the development of new porphyry deposits in the Cordilleran Belt.

Jan 1, 1973

By M. Dupuis

It has been previously demonstrated [l] that there is no obvious thermal balance related issue limiting the size of a Hall-Héroult cell. Yet, it is well known that a forced-air sidewall cooling system is part of the AP50 cell design [2], In the present study, the authors analyze the impact of thermal loading on the mechanical deformation of high amperage cell potshells. The effect of adding cooling fins or a forced-air sidewall cooling system is then assessed.

Jan 1, 2005

By Richard W. Hutchinson, Robert W. Hodder

"Pyritic massive sulphide deposits lie conformably above submarine volcanic rocks, and beneath siliceous and manganiferous iron formations. The massive bodies are often zoned, with a barren pyritic top grading downward into pyrite with sphalerite, and occasionally galena, and a chalcopyrite-rich base. They are frequently brecciated, like the lavas beneath them, which contain pyrite and chalcopyrite as coatings on joints and fractures and as dispersed grains. The lavas also exhibit propylitic, argillic and silicic alteration. These sulphide deposits appear to have formed on sea bottom from fluids escaping through the lavas during periods of exhalative and sometimes explosive volcanism. The process may be comparable to the present deposition of base metals from hot brines in the Red Sea. Some porphyry copper deposits resemble the altered, sulphide-impregnated lavas which lie beneath bodies of pyritic massive sulphide. In porphyry copper deposits, pyrite and chalcopyrite occur as veinlets and dispersed grains in intensely fractured tuffs, flows, sub-volcanic intrusions or other host rocks, characterized by propylitic, argillic and silicic alteration. Metal zoning is present; sphalerite and galena often occur in manganiferous veins peripheral to a shell of pyritic veinlets which encloses the mineable zone of chalcopyrite-bearing veinlets. This sulphide distribution appears to have formed from hydrothermal fluids escaping, either passively or violently, from solidifying magma. The fluids may be comparable to hot brines encountered by drilling in the Salton Sea area of California.There are also important differences between massive sulphide and porphyry copper deposits. The former usually occur in differentiated, mafic-to-felsic subaqueous volcanic rocks, whereas porphyry copper deposits are often associated with shallow plutons and subaerial volcanic rocks of intermediate to felsic composition. Calcic-sodic metasomatism accompanies the massive sulphides, whereas potassic metasomatism characterizes the porphyry cop.per deposits. Further, ages of massive sulphides range from Archean (Keewatin) to Tertiary, but porphyry coppers are Triassic to Tertiary in age. These similarities and differences suggest that massive sulphide and porphyry copper deposits are related tectonically and metallogenetically. The former were generated during early stages of crustal evolution, particularly in Archean time, and were repeatedly derived during early stages of younger, individual tectonic cycles. In contrast, the porphyry coppers developed during the later stages of crustal evolution - later in terms of both absolute age and relative age within younger individual tectonic cycles. They appear in younger rocks generally, and specifically in rocks involved in events of the middle and late tectonic stages of orogenic belts. The massive sulphide deposits are of early-magmatic eugeosynclinal affiliation, whereas the porphyry deposits formed in late-magmatic, predominantly subvolcanic settings at the edge of continental plates, where contemporaneous exhalative volcanism was mainly a subaerial phenomenon. Transitional types of deposits exist and are found on continental margins with flanking eugeosynclinal sequences."

Jan 1, 1972