Search Documents

By W. T. Thompson, S. Durham, K. M. Jaansalu

The role of platinum on the relative stability of gamma - gamma prime equilibrium is only qualitatively known, and may bear upon the stability of a superalloy under a protective coating. The binary phase diagrams Ni-Pt and Al-Pt, and the Ni-rich corner of the Ni-Al-Pt ternary, are reviewed and simple self-consistent thermodynamic models are derived. These thermodynamic models are incorporated into a database used to predict the gamma-gamma prime equilibrium for single crystal superalloys. In small concentrations, platinum is predicted to increase the temperature stability, but not the proportion, of the gamma prime phase over the gamma phase in third generation alloys such as CMSX-10. Another effect of platinum addition is to significantly lower the solidus temperature. These findings are compared to experimental data in the literature.

Jan 1, 2004

By Ian Thomson

The Social License to Operate ? We are operating in an era where social license in the resource industry is as important ? if not more important ? than mineral potential ? Concept proposed by Placer Dome executive Jim Cooney in 1997 as essential requirement for the future survival of the mining industry ? ?You don?t get your social license by going to a government ministry and making an application or simply paying a fee? It requires far more than money to truly become part of the communities in which you operate.? Pierre Lassonde, President of Newmont Mining Corporation (2003). What it is ?Granted by the local community ? Intangible, informal, non-permanent ? Has to be earned and then maintained ? Defined as ? Ongoing Acceptance (a lower level) ? Ongoing Approval (a higher level) ? Expression of the quality of the ?relationship?

Aug 1, 2013

By Owsiacki. Leo

Both the 8 and A-C ore zones of the Heath Steele Mine contain extensive areas of brecciated ore. This texturally distinct ore type has been tentatively defined as a fragmental or conglomerate massive sulphide. It consists of subangular and round fragments of pyrite up to 30 em in diameter, smaller quartz clasts and chloritized, mineralized, lithic fragments in a faintly banded matrix of pyrrhotite and chalcopyrite. The chalcopyrite is concentrated in the pressure shadows of the fragments and appears to reflect remobilization and recrystallization during a deformation which postdates the formation of the clasts. A generally conformable relationship with the underlying banded pyrite-sphalerite ore, discordancy with the host banded argillites, spatial distribution and similarity to Kuroko ores suggest that the fragmental ore is of primary origin and that breccia formation is probably due to soft-sediment slumping or sliding initiated by volcanic explosions, as hypothesized for similar massive sulphides in various Japanese mines. It is nevertheless recognized that certain structural features in some clasts may result from deformation preceding the formation of the breccia, and at this stage a tectonic origin cannot be completely eliminated.

Jan 1, 1979

By I. A. Cameron

In 1979, John Peacey and William (Bill) Davenport published The Iron Blast Furnace Theory and Practice billed as "An up to date and comprehensive treatment of blast furnaces from fundamental principles to modern operations" (back cover). As a 1979 graduate of McGill University’s Metallurgical Engineering program, I belonged to the last "beta" student group which completed the prescribed blast furnace course work before The Iron Blast Furnace Theory and Practice was published. As my career developed, I become an international blast furnace consultant and have worked with blast furnace operators and raw material suppliers on 5 continents. The blast furnace is the dominate iron making process responsible for 70% of global steel production. Blast furnace engineers have implemented many improvements by manipulating the blast furnace process metallurgy using the principles presented by Peacey and Davenport to reduce coke consumption and increase oxygen usage and blast furnace productivity. This paper briefly summarizes some key principles presented by Peacey and Davenport (1979), describes process improvements made by blast furnace operators over the 35 years since The Iron Blast Furnace Theory and Practice was published and outlines important future developments in blast furnace technology.

Jan 1, 2014

The North Saskatchewan River flows southwest to northeast through a 22-km-long valley in the City of Edmonton, supplying the drinking water to dozens of downstream communities. During heavy rains, combined sewers occasionally overflow into the river, which has a significant negative impact on the water quality and the sensitive environment. The West Edmonton Sanitary Sewer (WESS) W12, a syphon connecting the Rat Creek Trunk to the Gold Bar Wastewater Treatment Plant across the river, was designed and constructed to take the overflow to the wastewater treatment plant. Due to the complexity of the project, various 3D technologies were applied to facilitate decision-making processes. 3D models were developed for design review and design conflict detection, while 4D models were established to help create a robust construction schedule. Construction sequencing animation was used to convey design intents and demonstrate construction stages to contractors and workers. The combined applications of 3D technologies helped the project team to identify critical issues, and assured effective communication among engineers, management, contractors, and other parties. Therefore, it provided more opportunities for the success of the project.

Aug 1, 2013

By S. Koski, M. Schmalzel, D. A. Jacobson, S. Crosby, P. Cook, M. Mular

"Mining operations, whether new or existing, are constantly looking for ways to maximize production and improve energy efficiency, while keeping the footprint required to a minimum. The Nordberg MP1250 cone crusher was designed with these three goals in mind. A series of side-by-side evaluations comparing an MP1250 to an MP1000 were completed at two Freeport-McMoRan operations. The first evaluation began October 2009 in a tertiary position and the second began March 2010 in a secondary position, where it remains in full production today. Utilizing 25% higher power capacity than the existing MP1000 tertiary crushers, the MP1250 had 29% higher capacity and 17% lower specific energy, adjusted for differences in feed and product size. The MP1250 compared to the existing MP1000 secondary crushers achieved 30% higher capacity at a slightly reduced specific energy, while achieving a finer product.The MP1250’s higher capacity and energy efficiency may have application in many crushing plants. Depending on site specific economic factors, greenfield projects may benefit from a smaller footprint and less ancillary equipment, whereas brownfield projects may benefit from higher capacity or a finer product within the same footprint."

Jan 1, 2012

By Å. Partapuoli, M. Henriksson, P. Wikström, J. Worth, G. Adolfsson

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB’s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012

By Fritz F. Prugger

In August, 1970, during routine shaft grouting, a major water source was intersected. Water and quicksand under very high pressure entered the shaft at a rate of 65 m3 per minute. The mine and both shafts were flooded. The breach was sealed simultaneously from within the shaft and through a relief hole drilled from surface. The mine was dewatered, rehabilitated and the equipment was restored. Production resumed two years after the accident.

Jan 1, 1979

Today?s Topics ? Data to decision value chain ? Practical Considerations ? Example ? Before / After DSS ? Quick Decision Support Demo Practical Considerations ? More data is not necessarily better ? Organization and process silos ? Good vs. ?optimal?, but impractical Solutions

May 1, 2008

By R. J. Labine, D. I. Brisbin, R. Roussain, P. R. Coad

"Abstract - The Owl Creek Mine is located near the west end of the Neo-archean Abitibi greenstone belt, 17 km northeast of Timmins, Ontario, and 4 km north of the Destor Porcupine fault. Gold occurs in epigenetic quartz veins and their pyritic wallrocks in two zones within a package of east striking, steeply north dipping, volcanic and sedimentary rocks. At the West Zone, 1 729 603 t of ore with a grade of 4.83 g/t Au (268 587 troy oz.) were produced from an open pit centered on a wedgeshaped unit of Tisdale Group basalt that occurs between two overturned, south facing units of Porcupine Group graywacke and argillite. Basalt/graywacke contacts are locally marked by graphiticcarbonaceous argillite, strike-parallel faults and massive quartz veins.Deformed quartz+/-ankerite veins occur along the graphitic sedimentary/volcanic contacts and in gently to moderately dipping fractures in basalts, and, to a lesser extent, in graywackes. Veins also occur sub-parallel to steeply dipping 070° foliation. Altered host basalts are composed of iron carbonate, sericite, quartz, carbon, chlorite and disseminated pyrite. Gold occurs as inclusions in pyrite, and less commonly as free gold in fractures and along graphite-quartz grain boundaries in quartz veins. Fractures preferentially developed in more competent basalts during pre- to syn-ore deformation are interpreted to have provided the permeability required for emplacement of mineralized quartz veins. Carbonaceous basalt/graywacke contacts further enhanced gold deposition by acting as chemical traps. The interaction of hydrothermal fluids with these carbonaceous sedimentary rocks led to the characteristic local darkening of host basalts due to carbon impregnation and chlorite development."

Jan 1, 1998

By I. M. Gordon, J. Blackshaw

"Run-of-mine ore is reduced to 4 per cent on 4 mesh (3/ 16 inch), using four stages of dry crushing. The mill feed is then reduced to 2 per cent on 48 mesh and 60 per cent through 200 mesh, using one stage of ball milling in cyanide solution. During the subsequent treatment about one-tenth of the tonnage is removed as a table concentrate and ground to 77 per cent through 325 mesh. The size of the mill tailing is 66 per cent through 200 mesh.Four stages of ore reduction began when the dry crushing plant at No. 26 Shaft came into operation at a maximum rate of 440 tons an hour on July 31, 1941. A detailed description of the crushing plant was published in C .I .M. Trans., Vol. LVI, 1953.One-stage ball milling in cyanide solution came into full operation on January 11, 1938. The ball milling plant had a capacity of 4800 tons daily when reducing mill feed at 2. 7 per cent on 1/ 4 inch to 54. 3 per cent through 200 mesh. Primary grinding to 60 per cent through 200 mesh commenced May 22, 1945, when the feed was 3 per cent on 4 mesh. Under these conditions the capacity of the ball milling plant is estimated at 4300 tons daily. A description of the 11 Hollinger Crushing and Grinding Plant"" by D. C. McLaren was published in the Canadian Mining Journal, June 1944.The concentrate grinding circuit using a 7 x 15 low discharge ball mill and a 19-foot diameter bowl classifier with a 6-inch centrifugal pump to close the circuit began operating in the ball milling plant on October 24, 1939."

Jan 1, 1965

By Jack Zhang, Chuck Edwards

"The versatility and specificity of rare earth elements (REEs) have led to their use in an ever increasing variety of applications in new technologies. Consequently, demand for REEs has increased significantly. However, to separate REEs safely and effectively is a complex and expensive process. While China has consistently invested in R&D of REE processing technologies, there have been only sporadic activities in REE mineral processing in North America in the past 20 years. This paper presents a review of REE mineral processing technology, providing an update on current capabilities in REE mineral processing. This paper reviews REE extraction from the major commercially valuable REE-bearing minerals such as bastnaesite, monazite, and xenotime, and also from the ion-absorption type of REE deposits. Currently, there are four major REE mining areas in China, one in the United Sates, and one in Australia. A review of the REE extraction processes in these major REE mining areas closes out the paper.INTRODUCTION The rare earth elements (REEs) include the 15 lanthanide elements, plus yttrium and scandium. The lanthanide elements are normally categorized in two groups: the light rare earth elements (LREEs), i.e. lanthanum through europium (atomic number (Z) = 57 through 63); and the heavy rare earth elements (HREEs), i.e. gadolinium through lutetium (Z = 64 through 71). Yttrium is usually grouped with the HREEs due to similarity in physical and chemical properties. Table 1 lists the REEs, atomic numbers, and abundances in earth’s crust (Taylor and McCleannan, 1985). Promethium is the rarest due to lack of stable isotopes. REEs with low atomic numbers are more abundant than those with high atomic numbers. More interesting is that the REEs with even atomic numbers are much more abundant than adjacent lanthanide elements with odd atomic numbers as shown in Table 1."

Jan 1, 2012

By G. Russo

During the construction of the S.Martin La Porte access adit, 9m in diameter, extreme squeezing conditions occurred while crossing Carboniferous schistose formations, with diametric convergence up to 2m. Back-analysis of monitoring results shows that an acceptable simulation of the observed excavation behaviour can be derived using a combined analytical and numerical approach, with simple elasto-plastic laws but a progressive reduction of residual parameters and a relevant increase of dilatancy.

May 1, 2009

By R. E. Jones

"Crusher sizing and application in mining operations is the selection of a crusher or a series of crushers to reduce run of mine ore to a size suitable for either autogenous or conventional grinding. It is important that the crusher or crushers be sized to operate within the range to which they have been designed. By the range to which they have been designed, we mean that the reduction ration must be held between specified limits. Reduction ration is the relationship between feed size to product size.In todays plants reduction is usually accomplished in three stages by primary, secondary and tertiary crushers.Primary crushers are either jaw or gyratory and are designed to handle run of mine feed at an open side setting of 5-1/2” to 7”. Reduction ration should not exceed 7 to 1.Jaw CrushersThe model size of a jaw crusher signifies the feed opening. A model 60 x48 jaw has a feed opening 60” wide by 48” long. The 48” is the dimension between the top of the swing jaw and the top of the stationary jaw. The 60” is the width between the two side frames. The crusher open side setting is the discharge opening at the bottom of the crushing chamber with the jaws in an open position. When corrugated jaw plates are used, the open side setting is measured from tip of one jaw plate to the valley of the opposite jaw plate. If a jaw crusher has a 6” open side setting with a 1” jaw motion, you could also say it has a 5” closed side setting."

Jan 1, 1974

By G. Mucsi, J. Faitli, K. Bohács

"The authors developed an online tube rheometer to supplement a Netzsch MiniCer (Netzsch GmbH, Germany) stirred media mill in order to monitor online the rheological characteristics of the suspension and therefore the result of grinding during the process. Previously it was demonstrated that the above measuring system was working appropriately based on the preliminary tests. The product related stress model was applied for the evaluation of the grinding results. It was found that the suspension concentration and the change of the material properties during grinding, consequently the rheology strongly affects the grinding result, i.e. specific surface area, median particle size as well as specific grinding energy. The tested model limestone – water suspensions behaved Newtonian initially, then after a given grinding time their properties had changed and they become Bingham plastic. INTRODUCTIONStirred media milling now is a common practice to produce fine and ultrafine granular materials for different purposes. With an increasing demand of ultrafine powders for industries (Kwade, 1999), wet and dry ultrafine grinding has been increasingly used in various fields, such as minerals (Mucsi, Rácz, & Mádai, 2013)(Rácz, 2014), ceramic materials (Becker & Schwedes, 1999), pigments (Ohenoja, Illikainen, & Niinimäki, 2013), chemical products (Baláž et al., 2013), microorganisms (Kwade & Schwedes, 2002) and pharmaceutics (Afolabi, Akinlabi, & Bilgili, 2014). It is well known that suspension rheology affects the wet comminution of materials (He, Wang, & Forssberg, 2006a). The rheological behaviour of the suspension containing the ground particles might indicate the level of interparticle interaction or aggregation and therefore it is an important variable factor of the process control (Muster & Prestidge, 1995). The influence of the rheological behaviour of mineral suspensions on their grindability has attracted more and more interests and attention, especially on ultrafine grinding performance (He, Wang, & Forssberg, 2006b) (Bernhardt et al., 1999). However, there are still many issues concerning the machine and the process for the different applications. When grinding is effective and the particle size range decreases significantly, the circulating suspension is becoming typically non-Newtonian. The changed rheological behaviour and the increasing rheological material parameters can negatively affect the grinding efficiency; therefore it is an important issue. Ultrafine stirred media milling as well as solid-liquid two phase flow have been studied for a long time at the Institute of Raw Materials Preparation and Environmental Processing of the University of Miskolc. Regarding ultrafine grinding the research is focusing on the description of materials’ grindability (energetic aspects) both in wet and dry circumstances (Mucsi et al., 2013; Rácz, 2014). Concerning rheology, the three measuring pipes tube rheometer was developed decades ago (Faitli & Gombköto, 2015). So far many different solid materials from all over the world had been tested in this rheometer (Faitli & Gombköto, 2015). Main aim of these tests was to gain basic data for large scale hydraulic transport applications. Among the many stirred media mills there is a Netzsch MiniCer mill at the Institute. It was reasonable to combine the two fields together, and the goal of the research presented in this paper is to develop an online tube rheometer for the Netzsch mill and to carry out grinding and rheological testing simultaneously."

Jan 1, 2016

By J. L. Rodrigues Bravo

The aim of this paper is to show the results of the study that relate the variations of the bismuth content in the Caraíba Metais' electrolytic copper with the main electrolysis' process variables as electrolyte flow rate and temperature, anode's impurities content, electrolyte composition, current density, etc and their combinations and factors like cathode washing, blend of materials entering rod plant's furnace, analytical methods, shot-circuit inspection, etc. Also, the methodology considered arsenic, bismuth and antimony mass balance in the electrolysis and their electrolyte's molar ratio relations as well as bibliographic references of refineries that operate in similar conditions. The results showed the circumstances with the major probability of causing bismuth content increasing in the electrolytic copper and the main operating conditions that have to be fixed for having less bismuth variation and lower content in the electrolytic copper.

Jan 1, 2007

By Paul D. Young, Michael J. Allan

"The Con Mine has been producing gold continuously since 1938. In 1990 laboratory and pilot plant investigations began into the use of pressure oxidation for treatment of an arsenic trioxide waste product from two previous roaster operations on the property. This led to the construction in 1992 of a 96 ton/day plant to treat a mixture of arsenic waste and flotation concentrate from the existing mill. The plant was commissioned in the fall of 1992.This paper describes experience gained in the commissioning and initial operation of the plant. The unique aspects of treating a hazardous waste product are described including special operating procedures to satisfy environmental and employee safety concerns. The paper further describes modifications made to the process flowsheet, to operating procedures and to materials of construction in the early months of operation."

Jan 1, 1994

By C. A. Young

"The stabilization of tailings has been a matter of concern to the Mining Industry for many years. In earlier times, when mines were small and only high grade ore deposits were mined, the problem was not a great one. But, more recently - during the last 30 to 40 years - the increased world demand for various metals, combined with the vast strides that have been made in the improvement of metallurgical extraction processes, have resulted in the development of lower grade ore bodies.About 30 years ago The International Nickel Company started experiments to stabilize the surface of the tailings and prevent them from becoming a dust source under certain weather conditions. The use of chemicals to form seals, covering with crushed stone, mulching with straw and some early seedings were some of the stabilizing methods tried. Results were either unsuccessful or impractical economically.In 1954 a series of experiments to establish vegetation on the tailings began. Varying degrees of success were achieved but however unsuccessful a particular scheme turned out, the attempt to find a solution was never written off. As we look back, we realize that the first significant break-through came as the result of three test plots planted in the spring of 1957. Each plot covered an area of approximately one-third of an acre. One plot was successful and persisted until it was covered up by the expansion of the tailings area in 1961.In 1960 a review of all our test plots to that date was carried out to assess the factors which effect the chance of grass being established."

Jan 1, 1969

By Scott A. Stebbins

Cost evaluation models constructed specifically to evaluate the economic potential of an individually motorized railcar system of ore and waste transport demonstrate that the approach may be considerably more cost effective than traditional rubber-tired haulage methods. The system design places a motorized drive unit on each railcar, as opposed to the more common configuration in which a series of un-motorized cars trail behind a single locomotive. These motorized railcars are directed to various load and dump points by a computerized dispatch system, and as such have the advantage of operating unmanned. In addition, the tractive effort of the rail-type drive system is noticeably more efficient than that of the rubber-tired mode of transport. The savings are realized primarily through comparative reductions in the requirements for labor and, to a lesser degree, energy.

Nov 1, 2011

By Donald Leroux, Jean-François Wilhelmy, Ahmed Bouajila

"A young private R & D organization, COREM celebrated its 10th anniversary in 2009. Managed by a consortium of nine mining and metallurgical companies, COREM has the mandate of increasing the competitiveness of its member companies through the development and transfer of mineral processing innovations. Typical technologies developed by COREM include alternative mineral processing techniques, novel operating strategies, innovative sensors and process simulation software. Many of them were developed in partnership with universities and selected research organizations.Because the COREM membership base is broad (from ferrous to base, to precious metal industries), its R & D program must deliver technologies with applications within a wide spectrum of mineral processes. Comminution, physical (gravity and magnetic) separation, flotation, cyanidation, pelletizing and thermal processes are the main topics of the R & D program. A number of new technologies have been developed and transferred to the plants of member companies. These examples of transferable technologies demonstrate the capability of COREM to impact the bottom-line of its member companies.INTRODUCTIONCOREM is a private mineral-processing R & D organization that operates from its own laboratories and pilot-plant with its own staff of professionals and technicians (about 95 persons). It is managed and financially supported by a consortium of nine mining and metallurgical companies and three provincial and federal ministries. The very ‘down-to-earth’ mission statement of COREM is to increase the competitiveness of the mineral processing plants of its members. The eighteen plants upon which the COREM technology development program is currently based can be found in Québec, Newfoundland and Labrador, New Brunswick, the Netherlands and Botswana."

Jan 1, 2010